Epson Personal Station Mac Product Information Guide

ES-300GS pdsmacpg

: Epson Epson-Epson-Personal--Station-Mac-Product-Information-Guide-665285 epson-epson-personal--station-mac-product-information-guide-665285 epson pdf

Open the PDF directly: View PDF .
Page Count: 5

Download
Open PDF In Browser	View PDF

EPSON ES-300GS
, scanner cover

scanning
windpw

/

rubber
friction
plate

powei switch

scanning
window
.

/

216 mm by 356 mm (8.5 inches by
14 inches) US legal size

Minimum
document size:

55 mm by 90 mm (2.2 inches by
3.5 inches) business card (with the
attachable card guide)

Document
capacity:

10 sheets standard paper
(60 g/m2 to 90 g/m2)
5 sheets for thermal paper
(thickness 0.05 mm)
7 sheets for checks (thickness 0.16 mm)
3 sheets for business cards (thickness
0.1 mm to 0.23 mm) with the attachable
card guide

Scanning speed:

4 ppm (A4 or letter, 300 dpi BW)

Optical resolution: 300 dpi
-rollers

Output resolution: 50 dpi to 600 dpi

parallel in/t&ace
connector
rubber
friction
Plate

Maximum
document size:

Output mode:

Error diffusion: 3 modes
Dither: 4 resident modes and one userdefined mode

A/D converter:

8 bits

Image sensor:

CCD

Grayscale levels:

256 levels

Scaling:

50% to 200%

Text enhancement: Background elimination technology
) rollers

Brightness:

7 levels

Contrast:

256 levels

Gamma correction: 5 resident tables (linear, analog monitor,
3 printers)
Userdefined table

power<
mhour,

0 “Return pin” denotes the twisted-pair return, to be
connected at signal ground level. For interface wiring be
sure to use a twisted-pair cable for each signal, and to
complete the connection on the return side. These cables
should be shielded and the ground connected to the
chassis of the host computer and the scanner.

TTL level compatible

Electrical standard: As per ANSI X3.131-1986 standard
ID setting

Selectable from 0 to 7 with push buttons
(8 should not be selected; 9 selects the
GT-6500 or ES-6OOC emulation mode)

Cl All interface conditions are based on TTL level.

Scanners

4/96

EPSON ES-30OGS-3

EPSON ES-300GS
Connector type:

%-pin D-SUB COMeCtOr

Problems and Solutions
The problems you may have while using the scanner often
involve the operation of your software and computer.
Problems fall in the following major categories:
0 Incorrect setup of the interface

Signal pin assignments

0 Inappropriate selection of the scaflner functions

In this table, the direction of the signals is given relative to
the scanner.

Ll Incorrect setup of your computer or software
Cl Incorrect operation of your software
Cl Incorrect loading of documents.
Also see the documentation that came with your software
and computer for possible solutions.

Indicator lights
If an error occurs, the scanner stops operating and the
Ready and Error lights show the type of error.
Error type
Command error
InteIface em
Fatal emor

Rerdy
on
on
Flashing

Em
on
Flashing
flashing

Command error
The scanner has received incorrect commands from your
scanning software. When this error occurs, retry the scanning
operation. The scanner returns to normal operation when it
receives correct commands. Normally you do not need to
reset the scanner, which is done by turning the scanner off
and then on.
caution:
R Whenever you turn ofthe scanner, wait at least 20 seconds
befoe turning it back on. Rapidly turning it on and @can
damage the scanner.

Initialization

Interface error

The scanner can be initialized (returned to a fixed set of
conditions) in the following ways.

The scanner may not be properly connected to the computer.
Check the interface co~eCtions. Then turn the scanner off
and back on to reset it.

Hardware initialization:
0 When the power is turned on.

The interrupt settings or the port addresses for the interface
board may not be set correctly or may conflict with other
installed expansion boards.

0 When the scanner receives an ZiT signal at the parallel
interface (pin 31 goes low).
0 When the scanner receives a SCSI Reset signal at the SCSI
interface.
Software initialization:
0 When the software command ESC @ (initialize the
scanner) is received.
0 When the SCSI Bus Device Message is received.

EPSON ES-300GS-4

4/96

Scanners

EPSON ES-300GS
-

Fatal error
This error indicates one of the following problems:
The fluorescent lamp needs to be replaced.

Scanner Bundled Kit
The bundled kit for the scanner includes the following:

Paper is jammed in the document feeder.

ES-300GS-PC

ES-300GS-MAC

There is no document in the document feeder or the
document was not loaded correctly.

ES-3OOGS Personal
Document Station
Bidirectional parallel
interface card
Attachable card guide
Parallel interface cable
Xerox” Desktop Document
Management Suite”
for Microsoft@ Windows””

ES-300GS Personal
Document Station
SCSI interface cable
Attachable card guide
m*J?aper” Document
Management & Archival
Suite

The software may not be set up properly.
Check to see if the fluorescent lamp is on. If not, the lamp
may need to be replaced. Contact your dealer or a.qualified
service person for assistance.
Turn off the scanner and remove any paper that may be
jammed in the document feeder. If the scanner still does not
operate properly, or if this error occurs repeatedly, consult
your dealer.

Information Reference List

Make sure the document is loaded correctly in the document
feeder, and then resume scanning.

Engineering Change Notices

Check to see that your software is installed correctly. Also
make sure you have selected the correct device driver for the
scanner. See your software manual for details.

None

Product Support Bulletins
None

Note:
To clear afntal error, you will need to reset fhe scanner by turning
it offand then on.

Technical Support Bulletins
None
Related Documentation

Scanners

4/96

TM-ES3COGS

ES-3OOGS Service Manual

PL-ES3OOGS

ES-3OOGS Parts Price List

4003693

ES-3OOGS User’s Guide

CPD2766 4/95

Getting Started (-f’C)

CPD3392 3/96

Getting Started (Mac)

EPSON ES-300GS-5



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Creator                         : Capture Reviewer 2.01
Producer                        : Acrobat PDFWriter 3.03 for Windows
Create Date                     : Monday, May 18, 1998 2:15:50 PM
Title                           : Personal Document Station Mac - Product Information Guide
Subject                         : This document contains specifications, general setup/usage information, interface information, and troubleshooting tips.
Modify Date                     : 2007:02:26 08:10:26-08:00
Page Count                      : 5
Page Mode                       : UseOutlines

EXIF Metadata provided by EXIF.tools