Ericsson Wi Fi 20031001 802.11a Radio Module User Manual RAR20031001 ERM2 Manual 2
Ericsson Wi-Fi 802.11a Radio Module RAR20031001 ERM2 Manual 2
user manual
B2CH079AA B2CH079AA Product Manual ERM2 5 GHz WLAN Radio Module Document Date: Document Number : Document Version Number : Document Status: November 2007 PM-B2CH079AA Release © Copyright 2006 by BelAir Networks. All rights reserved.. Page 1 of 14 B2CH079AA Product Manual – ERM2, 5 GHz WLAN Radio Module November 2007 Page 2 of 14 PM-B2CH079AA Version 2 B2CH079AA Product Manual – ERM2, 5 GHz WLAN Radio Module Contents About this Document .................................................................... 3 Introduction .................................................................................... 4 Conditions of Use ........................................................................... 5 Module Installation and Service.................................................... 7 Final Product Requirements ......................................................... 8 Regulatory Statements ................................................................ 11 About this Document This document is a product manual for the B2CH079AA 5 GHz WLAN Radio Module, including its limitations on use in any product marketed or offered for sale. It is intended as a supplement to training and documentation by BelAir Networks Inc. or its authorized agents. November 2007 Page 3 of 14 PM-B2CH079AA Version 2 B2CH079AA Product Manual – ERM2, 5 GHz WLAN Radio Module Introduction The B2CH079AA (hereafter referred to as “the module”) is a 5 GHz radio module compatible with the IEEE 802.11 standard for Wireless LAN operation. It is designed to be interoperable with WLAN products which are based on Direct Sequence Spread Spectrum (DSSS) radio technology. The module contains a complete 802.11a radio and Medium Access Control (MAC) protocol engine which allows implementation of an 802.11a module. The module is not intended for stand-alone operation. It will only be marketed as a complete product, in conjunction with a package, DC power supply and antenna (hereafter referred to as “the product” or the “final product”). Since the module has a BelAir networks proprietary digital interface, it cannot be directly connected to any standard telecommunications or computer devices. It can only be used with final products designed and authorized specifically for that purpose. November 2007 Page 4 of 14 PM-B2CH079AA Version 2 B2CH079AA Product Manual – ERM2, 5 GHz WLAN Radio Module Conditions of Use General Conditions of Use This manual is intended to supplement training provided by BelAir Networks or authorized parties. The module B2CH079AA is only intended for use in BelAir Networks products and is not for sale to the general public as a stand-alone module. Please read this entire document, including the Regulatory Statements section before attempting to install or operate the module. Warning: Any use of B2CH079AA in any manner which is not expressly specified within this manual or specifically approved by BelAir Networks or its authorized agents will void the user’s right to operate this module, and is expressly forbidden by BelAir Networks. This includes any modification of the module, installation of the module in a configuration or used with an antenna which is not expressly listed in this document or approved by BelAir Networks. List of Approved Final Products The B2CH079AA module is only approved for use in the following BelAir Networks products: • BelAir200. See BelAir200 documentation for complete manufacturing instructions. • BelAir100. See BelAir100 documentation for complete manufacturing instructions. • BelAir50c. See BelAir50c documentation for complete manufacturing instructions. Operation of the module within the products expressly listed above is required to ensure compliance to all FCC and Industry Canada regulations. Any modification of the module, or its use in any configuration not expressly listed above may void the user’s right to operate this module. Country of Use B2CH079AA is certified with limited modular approval for use as an Intentional Radiator in the United States as device: FCC ID: RAR20031001 and in Canada as November 2007 Page 5 of 14 PM-B2CH079AA Version 2 B2CH079AA Product Manual – ERM2, 5 GHz WLAN Radio Module IC: 4674A-20031001. Please read all regulatory statements at the end of this document before any attempt to install or operate this module. The module is only certified for operation in the United States and Canada. Before attempting to install and operate this module in any other country, contact BelAir Networks for approval. Module Labeling One or more labels are applied to the module during manufacture, including a label which identifies the FCC and Industry Canada identification numbers. Do not attempt to remove any labels from the module. November 2007 Page 6 of 14 PM-B2CH079AA Version 2 B2CH079AA Product Manual – ERM2, 5 GHz WLAN Radio Module Module Installation and Service Installation into a Product The module shall only be installed by a technician trained by BelAir Networks or its authorized agents. It should only be installed into an approved product (see above) following all manufacturing and service procedures for that product. The module should only be installed into a final product in a manufacturing or service depot site. Caution: B2CH079AA is an electro-static discharge (ESD) sensitive device. All appropriate ESD measures must be taken when handling the module. Failure to employ appropriate ESD protection may damage the module. Module Service The module is not intended as a field-serviceable unit. It contains no fieldreplaceable or field-serviceable parts, or any external adjustable mechanisms. The module should only be serviced in a manufacturing or service depot site approved by BelAir Networks or its authorized agents. November 2007 Page 7 of 14 PM-B2CH079AA Version 2 B2CH079AA Product Manual – ERM2, 5 GHz WLAN Radio Module Final Product Requirements The requirements below apply to any final product in which the B2CH079AA module is installed. Antenna Usage and Module Transmit Power B2CH079AA module shall only be used in conjunction with the following antenna types as outlined in the table that follows: Antenna Models and Maximum Allowable Power Setting Frequency Band Channels Location 5.730 – 5.845 GHz 146 to 169 Maximum Rated Transmit Power with Antenna Type Indoor / Outdoor Antenna Gain Max Rated Transmit Power MaxRad MMO58004NF 4 dBi 20 dBm MaxRad MMO58010NF MTI MT-482003/N 10 dBi 20 dBm BelAir BMA000210 10.5 dBi 20 dBm BelAir BMA000203 15 dBi 20 dBm H+S SPA 5600/9/23/0/V 23 dBi + MTI MT-486001 28 dBi + MTI MT-485028/N MTI MT-485001 MAXRAD WISP4959018MBV Andrew P2F-52-NEA 22 dBi + 19 dBi 15 dBi 30 dBi + 20 dBm (P2P)* else 13 dBm 20 dBm (P2P)* else 8 dBm 20 dBm (P2P)* else 14 dBm 20 dBm (P2P)* else 17 dBm 20 dBm (P2P)* else 21 dBm 20 dBm (P2P)* else 6 dBm In order to comply with the FCC and Industry Canada rules in the USA and Canada, respectively, it is required to respect the maximum transmit power limits as follows for each of the antenna types. +, * see notes following : November 2007 Page 8 of 14 PM-B2CH079AA Version 2 B2CH079AA Product Manual – ERM2, 5 GHz WLAN Radio Module * P2P indicates that the rated transmit power is only permissible for use in point-topoint links. For point-to-multipoint or multipoint-to-multipoint links the power must be reduced as shown. These antennas require an external filter between the product and antenna, part number BMA000281-A Warning: Use of this module in conjunction with any antenna not expressly listed above will void authority to install or operate this equipment. Warning: Setting of module transmit power above the limits specified in the above table for a particular combination of antenna type, frequency of operation, and type of usage, will exceed FCC or Industry Canada limits and void authority to install or operate this equipment. Product Installation Products which contain B2CH079AA-A shall only be installed by professional installers trained by BelAir Networks or its authorized agents. In addition to normal installation procedures and good installation practice, professional installers are responsible to ensure that: 1. Only an approved antenna (see above) is connected to the module, and, 2. The antenna is mounted in such a manner and in such a location that access to the antenna by the general population is minimized. Access to the antenna by the general population should be limited to more than the minimum safety distance. This distances are outlined according to product type and whether high gain antennas are used: November 2007 Page 9 of 14 PM-B2CH079AA Version 2 B2CH079AA Product Manual – ERM2, 5 GHz WLAN Radio Module Minimum Safety Distances Radios with ERM2 RAR20031001 Product Standard Antennas RF boards : All valid combinations BelAir50, BelAir 100,100T,100S ERM2 ARM3C PSM1,2 WRM1,2 ERM2 ARM3C PSM1,2 WRM1,2 up to 19 dBi Any 10 dbi 15 dbi up to 30 dBi Any 25 dBi 25 dBi 35 cm (13.8 in) Distance BelAir 200 Distance ARM3C :RAR20000003 High Gain Antennas up to 19 dBi Any 10 dbi 125 cm (49.2 in) 15 dbi up to 30 dBi 50 cm (19.7 in) PSM1,2:RAR20004001, RAR20008001 Any 25 dBi 25 dBi 160 cm (63 in) WRM1,2 : RAR20006001, RAR20007001 Adherence to these rules by the professional installer is mandatory. See full installation procedures for the particular product for details. Product Labeling The following permanent label, or one containing equivalent information, must be affixed in a conspicuous location on the exterior of every product containing this module: This device contains the following: RAR20031001 IC: 4674A-20031001 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. November 2007 Page 10 of 14 PM-B2CH079AA Version 2 B2CH079AA Product Manual – ERM2, 5 GHz WLAN Radio Module Regulatory Statements The following regulatory notes apply to the product which contains module B2CH079AA. The following sections or equivalent information shall appear in the user-manual of the final product. Regulatory Information and Disclaimers Installation and use of this device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications to this product not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. The manufacturer is not responsible for any interference to radio or television equipment caused by unauthorized modification of this device, or attachment of any antennas or equipment other than those specified by the manufacturer. The manufacturer or its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. Manufacturer’s FCC Conformity Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by November 2007 Page 11 of 14 PM-B2CH079AA Version 2 B2CH079AA Product Manual – ERM2, 5 GHz WLAN Radio Module turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Manufacturer’s Industry Canada Conformity Statement This device has been designed to operate with an antenna having a maximum gain of 30 dB. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. RF Exposure Statement This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65C and found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF exposure from radio frequency devices. This device complies with FCC RF radiation exposure limits for an uncontrolled environment. The radiated output power of this Wireless LAN device is below the FCC radio frequency exposure limits. However, this device should still be installed November 2007 Page 12 of 14 PM-B2CH079AA Version 2 B2CH079AA Product Manual – ERM2, 5 GHz WLAN Radio Module and used in such a manner that the potential for human contact during normal operation is minimized. In order to comply with RF exposure limits established in the ANSI C95.1 standard, this equipment should be installed and operated at a minimum distance between the radiator and a human body. This minimum distance is: Minimum Safety Distances Radios with ERM2 RAR20031001 Product Standard Antennas RF boards : All valid combinations BelAir50, BelAir 100,100T,100S ERM2 ARM3C PSM1,2 WRM1,2 ERM2 ARM3C PSM1,2 WRM1,2 up to 19 dBi Any 10 dbi 15 dbi up to 30 dBi Any 25 dBi 25 dBi 35 cm (13.8 in) Distance BelAir 200 Distance ARM3C :RAR20000003 High Gain Antennas up to 19 dBi Any 10 dbi 125 cm (49.2 in) 15 dbi up to 30 dBi 50 cm (19.7 in) PSM1,2:RAR20004001, RAR20008001 November 2007 Any 25 dBi 25 dBi 160 cm (63 in) WRM1,2 : RAR20006001, RAR20007001 Page 13 of 14 PM-B2CH079AA Version 2 B2CH079AA Product Manual – 2.4 GHz WLAN Radio Module BelAir Networks Inc. 603 March Road Kanata, Ontario Canada K2K 2M5 613-254-7070 Sales sales@belairnetworks.com Support support@belairnetworks.com General Information Info@belairnetworks.com November 2007 Page 14 of 14 PM-B2CH079AA Version 2
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2007:11:15 11:21:36-05:00 Create Date : 2007:11:15 11:21:36-05:00 Format : application/pdf Title : Microsoft Word - RAR20031001_ERM2_Manual_2.doc Creator : mdubois Document ID : uuid:57bc0513-1376-4b01-825a-deb8b1b9d7e5 Instance ID : uuid:f10c6bbf-df1b-4ba7-b5f7-f9633be07590 Page Count : 14 Author : mduboisEXIF Metadata provided by EXIF.tools