Etross telecom ETS8848 FIXED WIRELESS TERMINAL(FWT) User Manual Characteristic

Shenzhen Etross telecom Co., ltd. FIXED WIRELESS TERMINAL(FWT) Characteristic

User Manual

3G WCDMA FWT-8848 User's Manual Version 1.013G WCDMA FWT-8848User's Manual3G WCDMA FWT-8848 Version 1.0 -2014
3G WCDMA FWT-8848 User's Manual Version 1.021, General Description3G WCDMA FWT-8848 is a WCDMA to Analog Converter(single port, insert 1sim card only), the device can produce a FXS line to allow a regular phone tobe connected and u sed just like a local landline(PSTN) except your calls willgo out the GSM network. This device can both receive and make calls.The main application is: Connecting the RJ-11 FXS line to connect Ordinarytelephone set for voice call; to connect PBX for call extensions; to connectbilling systems for public phone use; to connect VoIP FXO gateway to realizeVoIP call termination; to connect alarm system for security purpose, etc. It is nota VOIP gateway, nor a GSM+VOIP gateway, It is a GSM Fixed WirelessTerminal that produces an analog FXS phone line .Module employed:Longsung U61003G Tri-Band UMTS/HSDPA/HSUPA（WCDMA/FDD）：850/1900/2100 MHz2G Quad-Band GSM850/900/1800/1900MhzAppearance and StructureItem 3G WCDMA FWT-8848 RemarkAppearance White/blackMaterial ABS (Acrylonitrile Butadiene Styrene)Dimension 170mm×118mm×30mmExcludingantennaWeight 250g Weight of Main
3G WCDMA FWT-8848 User's Manual Version 1.03unitPower Switch Rocker switchPower Socket 12V DC inputPhoneinterfaceRJ112 RJ-11 portsAntennainterfaceSMA-femaleLED displayNo.1: Power, No.2.in use, No.3, in talk, No.4,Battery, if have, No. 5-7, Signal strengthFrom left toright(front sideview)Front side LEDs display for Signal strength, Power, WorkingStatus,Talking and Battery indicator;Rear side1pcs SMA antenna connectors, 2 RJ-11 output,Power port and switch;Bottom side1pcs Sim card holder slots, you can insert Sim cardinto the slot .2, Features:1) It is a 1 port WCDMA FWT which has 2 RJ-11 outputs for extensions;2) It can connect with ordinary telephone set, PBX , VOIP Gateway, Billing meteretc.3) Employ industrial module to make4) Simple to install and easy to maintain5) Steady module and reliable design ensures good performance6) Provides optimized circuit directly connecting the exchange device forextensions
3G WCDMA FWT-8848 User's Manual Version 1.047) Compatible to most telephones, PBX device.8) Strong signals with high gain antenna9) Attractive plastic casing10) SIM card supported (1.8V, 3V)11) Caller ID display12) Provides reversal polarity signal for metering13) No noise and clear voice14) Suitable for wide voltage range and low power consumption15) Suitable for all kinds of weather and environment16) Locking PIN / network (optional)3,Technical Specifications:Air interface standard:Longsung U6100 is a wireless module which is designed for the globalmarket. It is a consumptive product; it can be designed in many kinds ofapplications which can work on HSPA/UMTS/EDGE/GPRS/GSM network.U6100 support the Bands as the following:3G Tri-Band UMTS/HSDPA/HSUPA (WCDMA/FDD): 850/1900/2100 MHz;2G Quad-Band GSM: 850/900/DCS1800/PCS1900 MHzPhone interface: supply RJ-11 Phone InterfaceHanging voltage: 45VPicking off voltage: 30mA / 41mADialing tone Frequency: 450HzAntenna interface: Antenna amplifying>2.5dbSensitivity:<-104DBMTransmitting power<3WColor: White /Black (optional)AC-Adapter interface: Input: AC 110~240VAC 50~60HzOutput: 12DC 1A.AC-Adapter type: EU, US, AU, British can be optional4, Operation Circumstance:Operation temperature: -10c~60C
3G WCDMA FWT-8848 User's Manual Version 1.05Storage temperature:-20C~70COperation humidity:45%-95%Atmosphere pressure:86-106KpaEnvironment noise: <60DBTransmitting Power:2WSensitivity: <-104dbmAntenna Amplifying: >2.5dbDialing frequency: 450HzHanging voltage: 45VPicking current: 30mA/41mA5, Packing ListName Quantity Remark3G WCDMA FWT-8848 1pcs 3G/2GAc- adapter 1pcs AC-110-240V, DC12V/1AAntenna 1pcs Magnetic Antenna with 3mcableUser's Manual 1pcs EnglishG.W: 0.75kg per unit. 20pcs/Carton, 16kg /CartonCorton Box Size: 55cmX34.5cmX32.5cm6,Installation And ConnectionThe Condition for InstallationThe terminal asks for 110- 220V AV power supply. It must be installed in thearea where the GSM network can cover. The strength of the signal can affectthe quality of voice.1. Insert SIM card into the SIM card holder at the back of the terminal.2. Install antenna. In order to ensure the quality of voice, antenna must be putbeyond 1.5 from the telephone and terminal.3. On end of the telephone line connects to the “Phone” port of the terminal,the other end connects to telephone.4. “Power” port connects to power adapter that is connected to 110-220V ACpower supply.1) The Installation for Connecting to Ordinary Telephone
3G WCDMA FWT-8848 User's Manual Version 1.06The Sketch for connecting ordinary TelephoneDraw your attention: Because there are many types of ordinary telephone andtheir electric parameters are different. In order to avoid mutual disturbancebetween telephone and terminal and affect voice quality. The distance betweentelephone and terminal is 1.5m at least.2) The installation for connecting to billing device for meteringIf the users demand to register cost during calls, billing device can beconnected between terminal and ordinary telephone. Billing device register costaccording to the anti-polarity signal that is provided by terminal.The sketch for connecting to Billing device or Computer charging system
3G WCDMA FWT-8848 User's Manual Version 1.073) The installation for connecting to PBX for call extentionsIf users want to connect small PBX to this terminal, connect terminal’s “Phoneport” to the PBX.The sketch for connecting to PBX device.4) The installation for connecting VoIP gateway for Call TerminationSuppose a VoIP call originates from US, which was transferred from US Serverto China Server on VoIP, finally the call will be terminated from internet to GSMnetwork and to be sent out to the destination answer side.The sketch for connecting to VoIP gateway5) The installation for connecting to alarm system for SecurityThe GSM FWT can substitute the PSTN for connecting to alarm system for
3G WCDMA FWT-8848 User's Manual Version 1.08security purpose when PSTN failure or not available.The sketch for connecting to alarm system7, Function SettingBefore you do the following function settings, Lift handset or press hands freekey of telephone set, then you can press the buttons according to the followinginstructions to finish setting, you will hear 2 beeps when you finish, this testifysetting successfully.1) Restore to factory default setting*#99#99# restore to factory default setting.2) Adjust dial interval*#01#30# , 01--command，30--time，Max 9.9 seconds，Min 0.5 seconds, defaultsetting is 3 seconds.*If you use GSM FWT-8818 for connecting to VoIP gateway, you can set dialinterval as 0.5 second, it can make PDD<5 sec (Method: *#01#05#);*If you use GSM FWT-8818 for connecting telephone, PBX, billing device, youcan set dial interval as 3 seconds or 5 seconds as you like (Method: *#01#30#,set the dial interval as 3 seconds).3) Adjust Earphone Volume*#02#15# 02--command，15--volume，Max 16，Min 1, default setting is 15.4) Adjust Mic. Volume (sensitivity)
3G WCDMA FWT-8848 User's Manual Version 1.09*#03#10# 03--command，10--amount，Max 16，Min 1, default setting is 10.5) Setting local area code*#04#*0755# 10--command，*0755—area code，Max 5 numbers, use "*"instead if area code is less than 5 digits.6) Setting IP numbers*#05#17911# 05--command，17911—IP numbers，Max 5 numbers, use "*"instead if IP number is less than 5 digit.7）Hide Caller ID (been sent out)Setting*#13#01# 13--command，01--value，Max-02，Min-00 Default settingis 0000-- presentation indicator is used according to the subscription of theCLIR service01 – CLIR allowed02 – CLIR prohibitedNotice: This Setting need GSM carrier support.8) Bar incoming call Setting*#14#00# 14--command，00--value，00--no barring, 01--set barring defaultsetting --009)FSK setting (optional) (should confirm before order)*#17#00# setting caller ID17-order, 00-value, 00-DTMF, 01-FSK, default setting is 00This setting need terminal has FSK Chip set support10) Billing Mode setting*#15#00#15--command, 00-value, 01-reversal polarity, 02-12 KHz, 03-16 KHz, defaultsetting-- 0111）IMEI change Setting ( for Quad Band M35 Module only)1. Write IMEI to RAM*#18#IMEI no.#, 18--command, IMEI No. --15-digit IMEI no.2. Check IMEI, if it is right, and then write it to module.*#19#IMEI no.#, 19--command, IMEI No. --15-digits IMEI No.
3G WCDMA FWT-8848 User's Manual Version 1.010Notice: Step 1 and Step 2, IMEI no. must be same.12) Pin Lock &Network Lock Setting (optional)(Should confirm beforeorder)2)PIN Lock1, Set to open PIN code check and automatic PIN lock function*#07#*1234# 07-command, 1234- the current SIM card PIN codeIf set sucessfully, the device will open PIN code check, and automaticallychange the current SIM Card into "PIN on" from "PIN off"2, Set to close PIN code check and auomatic PIN lock function*#08#*1234# 08-command, 1234- the current SIM card PIN codeIf set sucessfully, the device will close PIN code check and automatic PIN lockfunction.3, Set to change PIN code, open automatic PIN lock function*#09#1234*56785678# 09-command, 1234- the current sim card PIN code,5678-new PIN code. (5678 can be any other 4 digits number, suppose you canuse 2009).If set successfully, the device will change the current sim card PIN code as youwant.5678, or the any other 4 digit PIN codes, and open automatic PIN lockfunction.2)Network Lock1,Set to open Network lock function*#10#01234# 10-command, 01234-password2,Set to close Network lock function*#11#01234# 11-command,01234-password3,Set the Network codes*#12#1*46003*46003# 12-command,1--No. Of IMSI, 46003--the IMSI code forChina Telecom*#12#2*46000*46000# 12-command, 2--No. Of IMSI, 46000--the IMSI code forChina Mobile8,Making Calls and Answer Incoming Calls
3G WCDMA FWT-8848 User's Manual Version 1.011Making Calls1. Lift the handset or press “hand-free” key, you will hear dialing tone, thenyou can dial the telephone numbers you want to call.2. Dialing: dialing the telephone numbers you want to call3. On completion of dialed digits, you can press “#” to transmit the calledtelephone numbers. If you don’t dial any key for continual 3 secondsduring the dialing, terminal transmits called telephone numbersautomatically.4. During calls, if the telephone numbers is not free ones, the terminalsends out anti-polarity signal.5. If the calling party or called party hangs up, the terminal stops sendingout anti-polarity signal.Answering Incoming CallsWhen some calls are coming in, if the connected telephone has the functionof displaying incoming calls, the telephone rings and displays the incomingtelephone numbers. Now users can lift the handset or press “hand-free” toanswer it.
3G WCDMA FWT-8848 User's Manual Version 1.012Warranty CardPlease fill in the blanks carefully, and keep it properly as the voucherfor warranty.Type of Equipment 3G WCDMA FWT-8848User’s name Contact with:Contact Tel.no.AddressDate of Ex-worksDate of Maintenance Damage Management MaintainerSales Agent(Stamp)Purchasing Date
FCC Statement Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures. - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. The distance between user and products should be no less than 20cm.

Navigation menu