Everspring Industry Co CC128 SOLAR Camera User Manual CC128

Everspring Industry Co Ltd SOLAR Camera CC128

Users Manual

1Figure 2Figure 1C128U SOLAR CAMERA KITInstallation and Operating ManualIntroductionThe Solar Camera is designed to economically provide safety,security, convenience to your home and business. Its solarpanel collects daylight and maintains a charge to the battery ofthe camera during daylight hours. A negligible amount of energyis released by the rechargeable battery to operate the cameraduring nighttime.The components included in the C128U Solar Camera Kit:¡´ 1 x Solar Camera with PIR and Solar Panel(Transmitter)¡´ 1 x Audio & Video Receiver¡´ 1 x Power Adapter for Receiver¡´ 1 x 3 Feet RCA/SCRT Cable¡´ 1 x 6V 1.2A Rechargeable Battery¡´ 1 x 9V Alkaline Battery¡´ 1 x Waterproof Rubber PlugCautionPay attention to the following before you install:1. Sufficient daylight: Solar panelrequires constant charge duringdaylight hours. Please mount thecamera at the location that canreceive sufficient daylight exposure.2. Detecting sensitivity: A passiveinfrared sensoroperates by detectingthe objectivemovement and heat.When the temperatureof the moving objectand its surroundingarea are close in value, it may reducePIR’s sensitivity. The motion detector’sinfrared beams radiate outward like the slat of a wooden fence.Prior to mounting, keep in mind that the motion sensor is moresensitive to the motion that crosses these “slats”, and lesssensitive to the motion that moves directly towards the sensor(see Figure 1 and 2.)3.Keep a light source during nighttime: The camera cannot workin total darkness. Please bear in mind the camera's viewingarea must be illuminated with a suitable light source duringnighttime.InstallationStep 1: Install the camera (refer to Figure 3):a. Use the fixing template provided to mark the position of thefour fixing holes. Drill four 5mm-diameter holes.b. Mount backplate by inserting two screws into fixing holes onthe top edge of backplate. (All electronic components arehoused within the backplate.)c. Adjust the “DWELL_SW(SW3)” knob on backplate to set uptransmission time (lock time) of images and voices. It can beset as 10,20,30 or 40 seconds.d. Adjust the “CH_SW” knob on backplate to set up a channel.And remember which channel you selected.e. Plug the camera’s 12 Pin plug (Cable) into socket on thebackplate, then secure the camera set (front cover) to thebackplate by inserting screws into two fixing holes on thebutton edge of front cover and backplate. And then insert thewaterproof rubber plug into the hole at the bottom of frontcover.f. The camera and PIR which under the main solar panelcabinet can be swiveled upward to 5°, downward to 45°(referto Figure 4) and 90° horizontally (refer to Figure 5)g. Adjust the camera and PIR angle according to your need.Figure 3Figure 5Figure 4
2Figure 6 European VersionFigure 7 American VersionFigure 7 American VersionStep 2: Install Receiver Unit(Two visions available: European and American)European Version (refer to Figure 6):To connect receiver to your TV:1. Plug the 1M Scart connector cable that packageincluded into your TV.2. Plug the other end, yellow (video), white (audio) and red(trigger) RCA connectors into the corresponding RCAconnectors on the receiver.American Version (refer to Figure 7):To connect receiver to your TV:1. Plug the yellow (video) and white (audio) RCA connectorsinto TV socket.2. Plug the yellow (video) and white (audio) RCA connectorsinto the corresponding RCA connectors on the receiver.Step 3: Install option accessory VCR Controller (refer toFigure 6 or Figure 7)By adding the optional VCR Controller (C755) will enable thesystem to automatically record anyone who approaches yourpremises. The VCR Controller will automatically switch yourVCR on to Record and Off once the person has left.Plug RJ45 connector of VCR Controller (C755) in AUX outlet ofthe receiver, and VCR will record the images and voices whenCamera detects movement. (Please refer to C755 manual forinstallation and operation).Operating Instruction:(1) Buzzer/Light ON/OFF SW: Select “Buzzer/Light SW” at"ON". When PIR camera is triggered, image and voices willbe transmitted. Upon receiving the signals, the receiversounds “Beep” twice in response and the LED will flash for1 minute.(2) Transmission time (lock time) of image and voices can beset as 10, 20, 30, or 40 seconds by carefully adjusting the“DWELL_SW (SW3)” knob of Camera.(3) When lock time of trigger is over, the camera will continuetransferring image and voices if PIR sensor is still undertriggered condition. Otherwise, the camera will send an“OFF” signal to the receiver and shut down images andvoices.(4) When PIR of the camea is triggered, the camera will send2.4GHz RF signal to the receiver. Thus, images and voiceswill be displayed on TV or monitors through the receiver.(5) When battery is low: a. In the condition of camera on, Camera sends a signal to thereceiver to lighten the “Battery” LED and sound two “beeps”for alert.b. If battery is low during image transmitting, the image willstay on for 5 seconds only. Then there will be two beepsand the “Battery” LED will be on.(6) If the camera battery is recharged to normal level, the lowBattery LED will be turned off when the camera is triggeredagain.You can also additionally have a 9V DC 300mA regulator powerAC adapter and wire it on S3 (refer to Figure 3) of backplate torecharge and to transmit images and voices continuously.Note:(1) What you should do when the camera does not work properly:a. Unscrew the camera (two screws on the edge of front cover)b. Press “SW1” on Wall Mount to restore the systemc. Turn off the receiver, then turn it on.d. Hang the camera on Wall Mount, and tighten 2 screws onthe bottom of the camera.(2) When battery is low, video automatically reduces to 5seconds to save battery.(3) Position the receiver and set up channel first while installing,then position the camera and set receiver in the samechannel with the camera.(4)When the image on TV is not clear, it means that somebodymay use the same channel as yours in your neighborhood.You can change both channels on the backplate of cameraand the receiver. Remember to set the camera in the samechannel as that of the receiver.
3SPECIFICATIONSCC128 CA117Camera Type CC128Picture Type Color CMOS Operating Frequency 2400-2483MHz (for 4 channels)TV System PAL/NTSC Transmission Range 75m in open spaceSensitivity 3Lux@F1.2 Channel Selection Switch 4 positions for 1~4 selectionLens Angle 78° DiagonalLens 4.3mm F2.0 Buzzer & Light Switch 3 positions for buzzer & light on /buzzer off/offCamera Angle Left & Right 90°¡Ó 5°, Down 45°Power Switch 2 positions for power on/ offMicrophone Build in Triggered Buzzer & Light function Build inTransmitting Frequency 2400~2483MHz (for 4 channels) Antenna Type RodAC Adapter 12VDC, 500mA AC adapterBattery 1 x 9V back up battery, 1x 6Vrechargeable solar batteryDwell Time Switch 4 positions for 10s/20s/30s/40sPower Supply Source Solar Panel (110*160mm)Channel Switch 4 positions for 1~4 selectionPIR Detect ionDistance/Angle 8M/90° (under 28°C)Connector 1 x RJ-45 for VCR Controller1 x DC Jack for Power3 x RCA Jack for triggered(red),audio(white), video(yellow)© 2002 Everspring Industry Co., All Rights Reserved… ………………………………………………………………………………………………………………………………………..…… D/NL/F/E/B/S/CH

Navigation menu