Everspring Industry Co SP103 Wireless Alarm System 908.42MHz User Manual

Download:
Mirror Download [FCC.gov]
Document ID	847577
Application ID	PQi+NMEpWSVsnH9arj5+kQ==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	28.45kB (355672 bits)
Date Submitted	2007-09-26 00:00:00
Date Available	2007-09-26 00:00:00
Creation Date	2007-09-24 17:54:58
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2007-09-24 17:54:58
Document Title	untitled

SP103 PIR DETECTOR
1. Do not position the detector facing a window or direct sunlight. PIR Detectors
are not suitable for use in conservatories or draughty areas.
2. Do not position the detector directly above or facing any source of heat, eg: fires,
radiators, boiler etc.
3. Where possible, mount the detector so that the logical path of an intruder would
cut across the fan pattern rather than directly towards the detector.(FIGURE
2b)
The PIR Detector is a Z-WaveTM enabled device and is fully compatible with any
Z-WaveTM enabled network. Z-WaveTM enabled devices displaying the Z-WaveTM
logo can also be used with it regardless of the manufacturer, and ours can also be
used in other manufacturer’s Z-WaveTM enabled networks. This PIR Detector is
controllable to our modules, such as On/Off Module AN135 and Lamp Module
AD130. Inclusion of this PIR Detector on other manufacturer’s Wireless Controller
menu allows remote turn-on of connected modules and their connected lighting
when the Detector is triggered.
(M)
10
The PIR Detector is designed to detect movement in a protected area by detecting
changes in infra-red radiation levels caused, for example, when a person moves
within or across the devices field of vision, a trigger radio signal will be transmitted.
100°
10
Adding to Z-WaveTM Network
2.0
0 2 4 6 8 10 (M)
In the rear casing, there is a tamper switch which is used to carry out inclusion,
exclusion or association. Put a Z-WaveTM Wireless Controller into
inclusion/exclusion mode, press the tamper switch on the detector to complete the
inclusion/exclusion process (FIGURE 1)
FIGURE 2a
FIGURE 2b
Installation
Choosing A Mounting Location
1 Front Cover
2 PIR Motion Sensor
3 Time-off Knob
The recommended position for a PIR Detector is in the corner of a room mounted
2m from the floor. At this height, the detector will detect movement up to 6-12m
depending on adjustment. (FIGURE 2a) Also, in this position, the 110 degrees
fan-shaped detection pattern can normally offer greater protection than mounting on
a flat wall. Before selecting a position for a PIR Detector the following points should
be noted:
1.
2.
4 Battery
5 Rear Cover
6 Tamper Switch
Using a Phillips screwdrivers to detach the rear cover. (FIGURE 3a)
Insert 2 AAA-size 1.5V batteries to the battery compartment, ensuring that
3.
Time-off knob controls how long the connected load or lamp will stay on after
the motion has been detected. It is set from 5 seconds to 12 minutes. “T”
means 5 seconds, while “+” is 12 minutes. After the expiry of preset time-off, the
Detector will turn OFF the load or the lamp plugged into the On/Off Module
AN135, Lamp Module AD130. The red indicator LED on the load or the
connected lamp will be off too.
correct polarity is put. (FIGURE 3b)
Refit the rear cover. (FIGURE 3c)
FIGURE 3a
FIGURE 3b
FIGURE 3c
4. Hold the rear cover in position and mark the two mounting holes. Drill the holes,
insert the plastic wall plugs and screw the rear cover to the wall using the
screws supplied. Offer the Detector up to the rear cover using screws as
originally supplied. (FIGURE 4)
2. When the tamper switch is pressed, the unit will enter normal mode. Upon
motion being sensed, the Detector will turn ON the load or the lamp plugged
into the On/Off Module AN135, Lamp Module AD130.
After the elapse of preset time-off, the Detector will turn OFF the load or the
lamp plugged into the On/Off Module AN135, Lamp Module AD130.
In normal mode with the tamper switch being pressed, the red indicator LED on
the Detector will not illuminate to conserve battery life when the detector is
triggered, (unless the battery is low).
3. By pressing the tamper switch for more than 5 seconds, and then release it.
The Detector will send an alarm command (ALARM_REPORT, Alarm Type ==
0x01, Alarm Level == 0x11) to the Module. The load or the lamp plugged into
the On/Off Module AN135 or Lamp Module AD130 will flash for 10 seconds.
FIGURE 4
Note: After removing batteries, wait for 5 seconds to refit batteries.
Operation
Advanced Operation
1. With the tamper switch not being pressed, the unit enters test mode, which
allows the user to make a test. When the movement has been detected, the
red indicator LED on the Detector will illuminate and the load or the lamp
plugged into the On/Off Module AN135, Lamp Module AD130 will turn ON. It
implies that the unit is working properly.
The following information is for someone that has some experience setting up a
Z-Wave system or someone that has computer software running a Z-Wave
controller.
Enabling/Disabling Power Saving Function (for testing)
Note: When the battery is connected, the LED behind the lens will be on for
about 1 minute as warming-up duration until the PIR has stabilized when the
LED turns OFF.
When no movement has been detected for 10 seconds, the SP103 will enter the
power saving mode. It can be disabled or enabled power saving function by setting
Configuration Parameter # 3.
Cannot carry out
inclusion and association
This parameter can be configured with the value of 0 through 127, where 0 means
power saving being enabled and others mean power saving being disabled.
PS : As long as the batteries have been refitted, the Detector will enable the power
saving function automatically.
Cannot control the
connected modules
Configuring the Phase Level of ON Command
The Configuration parameter that can be used to adjust the phase level of ON
command is transmitted is Configuration Parameter # 1. This parameter can be
configured with the value of 0 through 127.
The detector not working
1. Run out of battery
power
2. Check if reverse
battery polarity
3. Check if the detector
is out of order
1. Run out of battery
power
2. Check if the detector
is out of order
1. Replace a new
battery
2. Refit the battery with
correct polarity
3. Ensure the detector is
working properly
1. Replace a new
battery
2. Ensure the detector is
working properly
1.
1.
2.
Value
0: Set Device OFF(0x00)
Value
1-99: Set Device On (1-99)
Value 100-127: Set Device On to the last phase (0xFF)
3.
4.
Note: 0xFF means the device will be on to the last phase before the device was
turned off.
Wakeup Command Class
Run out of battery
power
Check if the mounting
location is proper
Check if the detector
is mounted above a
radiator or heater
Check if the detector
is out of order
2.
3.
4.
Replace a new
battery
Reposition its
mounting location
Remove the source of
interference or
reposition its
mounting location
Ensure the detector is
working properly
Specifications
SP103 will send a Wakeup Notification Command if it has been included into a
Z-Wave network. The prerequisite is the connected Z-Wave controller needs to emit
a node ID and wakeup time interval to the Detector.
Battery
1.5V AAA size x 2
Range
Up to 100 meters line of sight
Warm Up Time
PIR Detection Coverage
The SP103 will wake up every 4 hours (default) and resend the Wakeup Notification
Command unless configured for another time interval. The SP103 will stay awake
for 10 seconds and then go back to sleep to conserve battery life.
Frequency Range
About 1 minute
Up to 12m x 110° (at 2m mounting height & below 20°C)
908.42 MHz (US) / 868.42 MHz (EU)
*Specifications are subject to change without notice
A501110874R
The time interval between Wakeup Notification Commands can be adjusted if you
have a device in which that is supported. Refer to that device’s instructions. The
time interval of Wakeup Notification Commands is counted on the basis of minute
and minimum criterion is one minute. For instance, please always enter 60, 120,
or 180 seconds etc. all of which are equivalent to 1, 2 and 3 minutes respectively.
The time interval of wakeup cannot be entered 59, 61, 119, 121, 179 or 181
seconds.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
Troubleshooting
Symptom
Possible Cause
Recommendation
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
WARNING:
Do not dispose of electrical appliances as unsorted municipal waste, use separate
collection facilities.
Contact your local government for information regarding the collection systems
available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances
can leak into the groundwater and get into the food chain, damaging your health
and well-being.
When replacing old appliances with new once, the retailer is legally obligated to take
back your old appliance for disposal at least for free of charge.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2007:09:24 17:54:58+08:00
Modify Date                     : 2007:09:24 17:54:58+08:00
Format                          : application/pdf
Title                           : untitled
Document ID                     : uuid:2412c689-7ad5-4609-aab8-8b484843bc93
Instance ID                     : uuid:09ea5161-a79e-4564-b121-25e8232b28a2
Page Count                      : 4

EXIF Metadata provided by EXIF.tools