Everspring Industry Co ST812 FLOOD DETECTOR User Manual UserMan

Download:
Mirror Download [FCC.gov]
Document ID	2103159
Application ID	Br+Gq6HX5IMrDZ/LFYX9mA==
Document Description	UserMan
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.83kB (197878 bits)
Date Submitted	2013-10-28 00:00:00
Date Available	2013-10-28 00:00:00
Creation Date	2013-09-25 11:45:13
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2013-09-25 11:45:13
Document Title	Microsoft Word - ST812_A501112117R_ZDK4.54_美俄規
Document Creator	PScript5.dll Version 5.2.2
Document Author:	101199

Z-WaveTM enabled network. Z-WaveTM enabled devices displaying the Z-WaveTM logo
can also be used with it regardless of the manufacturer, and ours can also be used in
other manufacturer’s Z-WaveTM enabled networks. Inclusion of this Flood Detector
on other manufacturer’s Wireless Controller menu allows remote turn-on of connected
modules and their connected lighting when the Detector is triggered. Z-WaveTM nodes
in the system also act as repeaters if they support that function.
ST812 FLOOD DETECTOR
These instructions should be read in conjunction with your System Installation
and Operating Manual and be retained for future reference.
The Flood Detector consists of a transceiver, flood sensor and 3-meter flood sensor
cable. Protect your property from water damage! The Flood Detector is designed to
sense the presence of water in basements, yachts and many others residential and
commercial applications, providing early warning of developing floods. The Flood
Detector is designed so that the transceiver is mounted on the wall and the flood
sensor is placed in a location where water presence, such as a result of leakage or
flooding, is probable. Upon flood detection, the Detector will beep and flash and
report its status to the node ID. Once water is released, it will report to the node ID
as well.
Product Layout
The Flood Detector is powered by 3 x AA 1.5V alkaline battery. When battery level
drops below unacceptable level, the Detector flashes red LED once every 30 seconds
and reports low battery status to the node ID. When this occurs, the batteries should
be replaced as soon as possible.
Power Up
1. Undo and remove the screw from the bottom edge of the transceiver. Remove the
back cover.
c Two-color Indication LED (red & green)
d Flood Sensor
e Sensor Rack
f Flood Sensor Cable Rack
g Link Key
h Battery Compartment
Introduction
2. Unscrew the screw from the battery cover and remove the battery cover.
3. Fit 3 AA size 1.5V batteries to the battery spring.
The Flood Detector is a Z-WaveTM enabled device and is fully compatible with any
Note: Auto inclusion timeout is 4 minutes during which the node information of
explorer frame will be emitted once every 5 seconds. Unlike “inclusion” function as
shown in the table below, the execution of auto inclusion is free from pressing the link
key on the Detector.
Function
Description
LED & Beep Indication
No node ID
The Z-Wave Controller does not allocate a
node ID to the Detector.
2-second on, 2-second off
Inclusion
1.
Beep once whenever link
key is pressed once.
4. Refit the battery cover by fastening its screw.
2. Pressing link key three times within 1.5
second will enter inclusion mode. The
detector will stay “awake” for 10 minutes
to allow time for setting and device status
enquiring.
Include to or Exclude from a Z-WaveTM Network
In the rear casing, there is a link key which is used to carry out inclusion, exclusion,
reset or association. When first power is applied, its two-color LED flashes on and off
alternately and repeatedly at 2-second intervals. It implies that it has not been
assigned a node ID and cannot work with Z-Wave enabled devices. The Detector
will stay “awake” for 10 minutes when power is first applied to allow time for
configuration.
Please get familiar with the terms below before starting the
operations.
Function
Inclusion
Exclusion
Association
Reset
Have Z-Wave Controller entered
inclusion mode.
Exclusion
Description
Add a Z-Wave enabled device (e.g. Flood Detector) to Z-Wave network.
Delete a Z-Wave enabled device (e.g. Flood Detector) from the network.
After inclusion, you have to define the relationship between devices. Through
association, device can be assigned as master/slave, and specify which
slave is going to be controlled by which master.
Restore Flood Detector to factory default.
Reset
The table below lists an operation summary of basic Z-Wave functions. Please refer
to the instructions for your Z-WaveTM Certificated Primary Controller to access the
setup function, and to include/exclude/associate devices. The detector executes the
function of auto inclusion when…
Association
1.
Have Z-Wave Controller entered
exclusion mode.
2.
Pressing link key three times within 1.5
second will enter exclusion mode. The
detector will stay “awake” for 10 minutes
to allow time for setting and device status
enquiring.
1.
Press link key three times within 1.5
second. The detector will stay “awake” for
10 minutes to allow time for setting and
device status enquiring.
Beep once whenever link
key is pressed once.
2.
Within 1 second, press and hold the link
key until beep tone stops.
Long beep for 5 seconds
3.
IDs are excluded and all of preset
value will be reset to factory default.
2-second on, 2-second off
1.
Have Z-Wave Controller entered
association mode.
Beep once whenever link
key is pressed once.
2.
Pressing link key three times within 1.5
second will enter association mode. The
detector will stay “awake” for 10 minutes
to allow time for setting and device status
enquiring.
3.
There are two groupings - 1 and 2. Refer
to Z-Wave’s Groups as described on
page 3 & 4.
Auto Inclusion
The function of auto inclusion will be executed as long as the Detector does not have
a node ID and in situations where…
1. The power is first applied.
Beep once whenever link
key is pressed once.
ÚIncluding a node ID allocated by Z-Wave Controller means inclusion.
2. The execution of exclusion/reset is successful where the stored node ID is cleared.
ID allocated by Z-Wave Controller means exclusion.
Excluding a node
ÚFailure or success in including/excluding the node ID can be viewed from the Z-Wave
screws provided.
4. Refit the transceiver to the back cover and secure with the fixing screw supplied.
5. Place the flood sensor cable and flood sensor to its rack.
Controller.
Installation
Note: The transceiver should never be submerged in water.
A clean smooth surface is required to mount the Flood Detector securely. The length
of flood sensor cable is 3 meters. If a 3-meter cable is too long, roll up the cable and
fasten it by twist ties. The transceiver should be placed as high up as possible on the
wall to improve communication and to prevent it from coming into contact with water in
case of flooding. After completion of battery insertion and set up, follow the below
procedures:
Programming
1. Z-Wave’s Groups (Association Command Class Version 2)
The Flood Detector supports two association groups with one node support for
Grouping 1 and three nodes support for Grouping 2. This has the effect that when the
Detector is triggered, all devices associated with the Detector will receive the relevant
reports.
1. Attach the flood sensor near the floor.
2. Use the back cover, flood sensor cable rack and sensor rack as a template to
mark the position of fixing holes on the wall. Drill the holes and insert the plastic
wall plugs supplied respectively.
There are two kinds of reports: ALARM_REPORT and SENSOR_ALARM_REPORT.
1-1 Grouping 1 (Max. node 1)
1-1-1
Power Applied command
The Detector will send ALARM_REPORT command to the nodes of
Grouping 1 to inform the devices that the Detector is powered up.
ALARM_REPORT Command:
[Command Class Alarm, Alarm Type = 0x02, Alarm Level = 0x01]
1-1-2
Flood Event Report (Binary Sensor Report)
Once the Detector has been triggered by water, the Detector will send
SENSOR_ALARM_REPORT to the nodes of Grouping 1 to inform them
there is a flood event; meanwhile, its red LED will flash for one minute
and beep for 30 seconds. Wait till water is released,
SENSOR_ALARM_REPORT will be sent to the associated devices.
SENSOR ALARM REPORT Command:
Event Present:
[Command Class Sensor Alarm, Sensor Alarm Report, Sensor Type
Water Leak Alarm State = 0xFF(255), Seconds = 0x00]
Event Clear:
[Command Class Sensor Alarm, Sensor Alarm Report, Sensor Type
Water Leak Alarm State = 0x00(0), Seconds = 0x00]
3. Fix the back cover, flood sensor cable rack and sensor rack using the fixing
1-1-3
3. Advanced Programming
Low Battery Report (Alarm Command Class)
When the battery level of the Detector drops to an unacceptable level,
the Detector will send a low battery command to the nodes of Grouping
1; meanwhile, the Detector will flash red LED once every 30 seconds.
3-1 Low Battery Indication
The users can also enquire the battery status of the Detector by sending
BATTERY_GET command via Z-Wave Controller. Once the Detector receives
the command, it will return BATTERY_REPORT command. The Detector will
send Battery_Level = 255 (0xFF) command to the Z-Wave Controller to inform
that the Detector is in low battery status.
ALARM REPORT Command:
[Command Class Alarm, Alarm Type = 0x01, Alarm Level = 0x01]
1-2 Grouping 2 (Max. nodes 3)
BATTERY REPORT Command:
[Command Class Battery, Battery Report, Battery Level = 20%-100%]
1-2-1 Control other Z-Wave devices
When the Detector has been triggered, it will control other Z-Wave
devices for operation by sending Basic Set command to the nodes of
Grouping 2; meanwhile, the Detector will flash red LED for one minute
and beep for 30 seconds.
3-2 Wakeup Command Class
The unit stays in sleep status for the majority of time in order to conserve battery
power. However, it can be woken up at specified intervals by setting
WAKE_UP_INTERVAL_SET command by Z-Wave Controller. After the unit
wakes up, it will send Wakeup Notification Command to the node ID that
requires to be reported. The minimum and maximum wakeup interval is 60
seconds and 194 days respectively. Allowable interval among each wakeup
interval is 1 second, such as 60, 61, 62 ….
Basic Set Command:
Event Present:
[Command Class Basic, Basic Set, Value = Basic set level]
Event Clear:
[Command Class Basic, Basic Set, Value = 0x00(0)]
2. Z-Wave’s Configuration
4. Command Classes
2-1 Basic Set Level
The Flood Detector supports Command Classes including…
When Basic Set Command is sent where contains a value, the receiver will take
it for consideration; for instance, if a lamp module is received the Basic Set
command of which value is decisive as to how bright of dim level of lamp module
shall be.
*COMMAND_CLASS_SENSOR_BINARY
*COMMAND_CLASS_BASIC
*COMMAND_CLASS_CONFIGURATION
*COMMAND_CLASS_WAKE_UP_V2
*COMMAND_CLASS_MANUFACTURER_SPECIFIC
*COMMAND_CLASS_VERSION
*COMMAND_CLASS_ASSOCIATION_V2
*COMMAND_CLASS_BATTERY
*COMMAND_CLASS_SENSOR_ALARM
*COMMAND_CLASS_ALARM
Example:
0: OFF
1-99: ON
(Binary Switch Device)
Dim Level (Multilevel Switch Device)
Function
Basic Set level
Parameter Number
Size
Configuration Command
Range
0~99
Default
99
Operation
1. When water is detected, the Detector flashes red LED for one minute and beeps
for 30 seconds as maximum during which an event report will be sent to the node
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
ID. In normal mode, the detection interval is set for one minute. If the Detector is
triggered, it will not be triggered again until one minute has elapsed, thus avoiding
false trigger.
2. When water is released, the green LED on the Detector will illuminate once.
3. When the battery level on the Detector drops to a certain level, the red LED will
flash once every 30 seconds and an event report will be sent to the node ID.
Troubleshooting
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Symptom
Possible Cause
Recommendation
LED not indicating and
working
Batteries have not been
fitted or insufficient
battery power
Check out if batteries are
fitted or replace new
batteries
Break down
Do not open up the Detector
and send it for repair
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
The unit is not
discharged completely.
After removing batteries,
press the Link Key several
times. Wait for 10 seconds
and replace batteries.
Unit does not stay
“awake” for 10 minutes
after power-on.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
WARNING:
Do not dispose of electrical appliances as unsorted municipal waste, use separate
collection facilities.
Specification*
Battery Type
Battery Life
Operating Frequency
FCC ID
1.5V AA x 3 pieces
2 years**
908.42 MHz (US) / 869 MHz (RU)
FU5ST812
Contact your local government for information regarding the collection systems
available.
*Specifications are subject to change without notice
**10 triggers per day
A501112117R
If electrical appliances are disposed of in landfills or dumps, hazardous substances
can leak into the groundwater and get into the food chain, damaging your health and
well-being.
2013/09
When replacing old appliances with new ones, the retailer is legally obligated to take
back your old appliance for disposal at least for free of charge.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2013:09:25 11:45:13+08:00
Create Date                     : 2013:09:25 11:45:13+08:00
Format                          : application/pdf
Title                           : Microsoft Word - ST812_A501112117R_ZDK4.54_美俄規
Creator                         : 101199
Document ID                     : uuid:71be4151-a8ae-4464-af3a-409ac97b9212
Instance ID                     : uuid:74c2174d-232a-4833-a332-35e523e67fa1
Page Count                      : 5
Author                          : 101199

EXIF Metadata provided by EXIF.tools