Ewig Macao Commercial Offshore NU-601 Wireless Food Thermometer Transmitter User Manual manual

Ewig Industries Macao Commercial Offshore Limited Wireless Food Thermometer Transmitter manual

Contents

users manual

Simple WirelessFood/Meat ThermometerUser GuideSimple Two Step SetupSimple Set up Instructions Remote Sensor:1. Remove the stand clip from the four comers on back of unit.2. Insert 3 AAA Alkaline or Lithium batteries in remote sensor byremoving the four screws on back of unit. (The stand clip mustbe removed)3. LCD display will show all segments of 3 seconds4. Attach sensor if required for application5. Sensor will automatically link to Main Station when MainStation is activated.6. Press the C/F button toggle between Centigrade andFahrenheit.Simple Set up Instructions Main Station:1. Insert two AAA Alkaline or Lithium batteries in mainstation in battery compartments.2. LCD display will show all segments for 3 seconds andkeeps and goes into to receiving mad for 1 minute.3. Main Station automatically links remote transmitters.Write the sensor number on back of remote sensor toinclude which channel is being used for a particularsensor.Specifications: Operating Instructions Main Station:Temperature Range –40F to 392F (40°C to 200°C)LLL indicates reading less than –40F (40°C)HHH indicates reading more than 392F (200°C)Display resolution 1 degree C/F Indoor temperatureTemperature range 32F to 122F (0°C - 122°C)LLL indicates reading less than 32F (0°C)HHH indicates reading higher than 122F (50°C)1. Normal operation – The Main Station automatically linksup to three remote transmitters. If more than onesensor is being used the next higher channel isautomatically selected. If all three channels are in use,the main station will automatically replace Channel 1.2. C/F button – on back of unit is used to toggle betweenCentigrade and Fahrenheit.3. Hi/Low Button – Pressing the Hi/Low button on back willtoggle between higher than and lower than temperatureset points. This is indicated by arrows on the LCDscreen.4. Channel Button – on back will change channel displaywhen multiple sensors are used. A Channel Auto scrollfeature in enabled by holding the Channel button downfor 2 seconds. The remote temperature display will thendisplay each remote sensor for 2 seconds.5. Hi/Low Button & Channel Button – When pressedtogether it allows toggling between indoor temperaturedisplay or set temperature display.6. Set Button – on front is used to set remote temperaturealarms. Depressing the set button will allow a togglebetween channels when multiple sensors are in use.7. Up arrow – pressing the up arrow on front is used in setmode and will increases the set temperature 1 degreeper second.8. Alarm Set Point Reached – When more than oneremote alarm set point is reached the left most displaywill be overwritten with the temperature with the remotesensor temperature that has reached its set point.9. Alarm – The Alarm will sound when the set temperatureis reached until.Battery Life – 5 months depending on useLow Battery indicators – if remote sensor batteries or main stationbatteries are low an icon will be present on main station. Caution: Donot mix alkaline batteries with Cadmium or Lithium batteries.Note: The temperature displayed is taken from the interior sensorunless probe is used. When the probe is used the temperaturedisplay is form the probe itself.FCC Statement:This device complies with part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) This device may not causeharmful interference, and (2) this device must accept anyinterference received, including interference that may causeundesired operation.A. Any front key is pressed (Set or Up arrow)B. The Alarm Times Out after 1 minuteNOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may causeharmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.Remark:Modifications not authorized by the manufacture may void users authority to operate this device

Navigation menu