Extreme Networks AP3915E Wireless 802.11 a/ac+b/g/n Indoor Access Point User Manual AP7632 rev 2

Extreme Networks, Inc. Wireless 802.11 a/ac+b/g/n Indoor Access Point Users Manual AP7632 rev 2

Contents

Users Manual (AP7632)_rev 2.pdf

Installing the ExtremeWiNG 802.11 a/ac+b/g/n
Indoor AP7632 Access Point
Overview of the AP7632
The AP7632 is an 802.11ac Wave 2 Access Point featuring dual 2x2:2 radios.
The all-metal design of the AP supports high operating temperatures, external
antennas, and flexible mounting options for wall mount, ceiling mount, beam
or T-bar. The AP can be powered by 802.3af or by using a 12VDC wall brick.
The AP7632 model has the following features:
• Radios: 2 radios (2.4GHz and 5GHz); 1 IoT Radio (2.4 GHz)
•Console Port: RJ45
• One RJ45, 10/100/1000 Ethernet Port (LAN1) with PoE
•LEDs: 4 (see Figure 2)
•One Reset button
• Power: PoE 802.3af; 12VDC power in connector (see Table 1)
• Antennas:
–Five external antennas (four band-locked antennas and one BLE
antenna)
– Three RSPMA mount style antenna connectors
• External USB 2.0 port with features to support a locking module
•Safety Hangar provision
• Temperature:
– -20 to +55*C ambient temperature anywhere
– -20 to +70*C ambient temperature near sea level
• Enclosure: Plastic with metal base
In Figure 1, the top image indicates the top view of AP7632 and the bottom
one indicates the side view of AP7632.
Figure 1 Top and Side View of AP7632
Table 1 shows ways to power the AP7632.
Table 1 Powering the AP7632
Note: The AP7632 requires a minimum base firmware of WiNG 5.9.1.
12.4G/5G Radio 1 and 2
2GE1/PoE
3Console RJ45 connector
4Reset button
5Optional 12V DC power supply connector
6BLE Radio
7Kensington Lock Slot
82.4G/5G Radio 1 and 2
1USB Port
Power Source Description
Power over
Ethernet
(PoE)
Power is provided through the RJ45 Ethernet port (GE1 port)
to the right of the 12V DC port. This is the preferred method
of powering the AP on ceiling and high wall installations.
Figure 2 shows the LEDs on the front of the AP7632.
Figure 2 LEDs on AP Front Face
Green LEDs indicate 2G Wi-Fi Radio, Amber LEDs indicate 5.2G Wi-Fi Radio,
and Blue LED indicates the IoT Radio. The Status LED is ON only during
diagnostics.
For detailed installation information about the AP7632, see the Extreme
Networks WiNG AP7632 Installation Guide.
Verifying the AP7632 Box Contents
Verify the contents of the box and ensure that the following items are
available:
Mounting and Connecting the AP
Use these instructions as guidelines for mounting and connecting the AP7632
easily and safely.
The AP7632 comes with a Mounting Bracket (ordering part #37201) that can
be used to mount the AP on a flat surface. You can also purchase an optional
flat metal indoor bracket (ordering part #37210) for easy installation.
You also have an option to purchase the optional adapter if you want to mount
the AP on a drop ceiling or mount it to a beam.
For more information about installing the optional bracket and the adaptor,
see the Extreme Networks WiNG AP7632 Installation Guide.
For installation videos of the AP, see www.extremenetworks.com/support/
Mounting the AP on a Dry or Wood Wall/Solid Flat
Ceiling
To install the AP on a dry wall or flat surface:
Option 1: Using the Main Bracket
1 Use the main bracket as a template and mark the hole centers on the wall.
2 Drill two holes 81mm (3.200”) apart from each other on the wall where you
want to mount the AP.
3 Insert the screws through the bracket and into the holes. Use the screw-in
anchors if needed.
4 Insert the Ethernet cable’s RJ45 connector into the LAN1/GE1 port.
5 Slide the AP onto the bracket’s four feet. Ensure that the AP is secured in
place and tightened.
External 12V
DC power
supply
(optional)
The AP7632 can also be powered by an external DC power
supply plugged into an AC source. Plug the supply’s input
jack into the DC-In port (callout 5 in Figure 1).
1IoT Radio 4Status
2Radio 1, 2.4GHz
3Radio 2, 5GHz
Table 2 Contents of the AP7632 Box
Quantity Item
1 AP7632 Quick Reference Guide
1 Mounting Bracket for 802.11ac Indoor AP assembled onto the AP
1 Cloud Quick Start Card
The following hardware is included:
2 Phillips Pan-head wood screws
2 Screw-in anchors
Electrical Hazard: Only qualified personnel should perform
installation procedures.
Note: Remove the main bracket from the AP to use it as a template.
Note: The four feet of the bracket must be horizontal and pointing to
the right. The flat part of the large surface must be touching the wall.
Power Source Description Option 2: Mounting the AP directly to the wall using 2 screws
1 Remove the main bracket attached to the back of the AP.
2 Drill two holes 104mm (4.100”) apart from each other on the wall.
3 Insert the screws into the holes and use the screw-in anchors if needed.
4 Insert the Ethernet cable’s RJ45 connector into the GE1 port (Figure 1; side
view). Attach the optional DC adaptor if there is no PoE on the Ethernet
cable.
5 Insert the keyholes of the AP onto the screws and slide it down till it is
firmly held by the screw heads. If the AP is loose, unmount the AP and
decrease the distance between the screw head and the wall. Remount the
AP.
Figure 3 Attaching AP to a Wall using 2 screws
Option 3: Using an optional Flat Metal Indoor Bracket
1 Attach the Flat Metal Indoor bracket to the main bracket. Keep the adaptor
to the center of the bracket, push and rotate it (Figure 4).
2 Hold the AP to the surface to which it needs to be attached and use the
optional adapter’s end holes as a template to mark the attachment holes.
3 Drill two holes on the solid surface (wall or ceiling) where you want to
mount the AP.
4 Connect the LAN/Ethernet cable to the back of the AP.
5 Hold the AP, insert and tighten the 2 screws until you lock it into place.
Figure 4 Attaching the optional Flat Metal Indoor Bracket to
the main bracket
Option 4: Using an optional Wall and Box bracket
Remove the main bracket from the AP. Follow the procedure mentioned in
ExtremeWireless AP7632 Installation Guide to mount the AP on a Wall and
Box bracket.
Mounting the AP to a Bracket on a Junction or Gang
Box
To mount the AP to a Bracket on a Junction or Gang box, use the Wall and Box
Bracket (needs to be purchased separately).
1 Remove the main bracket from the AP.
2 Follow the procedure mentioned in ExtremeWireless AP7632 Installation
Guide to mount the AP on a Wall and Box bracket.
Mounting the AP to a Suspended or Drop Ceiling
1 Attach the T-bar adaptor by pushing down the main bracket’s angled
locking tabs, pulling up on the T-bar adaptor’s locking pin, and
Note: Leave 1/8” gap between the screw head and the wall.
Note: Mounting the AP to a flat ceiling/wall requires the optional Flat
Metal Indoor Bracket (Purchasing Part #37210), which must be
purchased separately.
Note: Mounting the AP to a flat ceiling/wall requires either the Main
Bracket (Option 1), Flat Metal Indoor Bracket (Option 3), or the
optional Wall and Box Bracket (Option 4 - purchasing part #30516),
which must be purchased separately.
Note: The slot and lock cuts in the rear of the AP (visible when the
main plate is removed) are used for mounting the Wall and Box
bracket. The unlock tab on the bracket should be pointed up. In this
position, the AP7632 can be mounted with the antennas facing
upward or downward.
Note: Mounting the AP to a suspended or drop ceiling requires the
optional adapter (Universal Mounting Kit for EWLAN APs; purchasing
part # KT-135628-01), which must be purchased separately.
simultaneously rotating the adaptor onto the Main Bracket until the locking
pin clicks in place.
2 Slide the T-bar holder onto the T-bar and replace the tiles to hold the
adaptor onto the T-bar.
3 Hold the AP and rock it back and forth to ensure that it is securely
mounted.
4 Attach the Ethernet cable’s RJ45 connector to the LAN1/GE1 port.
The optional WS-MBI-DCMTR01 (purchasing part #30518) adaptor can also be
used for T-bar installations without the mounting bracket. For detailed
instructions, refer ExtremeWireless AP7632 Installation Guide.
Connecting a Power Supply to the AP7632
If you need to power the AP7632 with an external 12V DC power supply, you
can plug the power cord into the power connector (callout 5 in Figure 1) on the
back of the AP. There is no wall mount for the 12V DC power supply. When the
device is powered on, the power LED on the front face of the AP is lit. Refer to
the Extreme Networks WiNG AP7632 Installation Guide for
information about optional power supplies.
LAN/Console Connections
The AP7632 has one GE1 (Ethernet) port and a Console port. Refer to Figure 1
for the location of these ports. During administration and maintenance
through the GE1 or Console, the AP must still have a power connection
through either an Ethernet PoE cable or a DC power supply.
Professional Installation Instruction
Installation personal
This product is designed for specific application and needs to be installed by a
qualified personal who has RF and related rule knowledge. The general user
shall not attempt to install or change the setting.
Installation location
The product shall be installed at a location where the radiating antenna can be
kept 36 cm from nearby person in normal operation condition to meet
regulatory RF exposure requirement.
External antenna
Use only the antennas which have been approved by the applicant. The non-
approved antenna(s) may produce unwanted spurious or excessive RF
transmitting power which may lead to the violation of FCC/IC limit and is
prohibited.
Installation procedure
Please refer to user’s manual for the detail.
Instructions d'installation professionnelle
Installation
Ce produit est destine a un usage specifique et doit etre installe par un
personnel qualifie maitrisant les radiofrequences et les regles s'y rapportant.
L'installation et les reglages ne doivent pas etre modifies par l'utilisateur final.
Emplacement d'installation
En usage normal, afin de respecter les exigences reglementaires concernant
l'exposition aux radiofrequences, ce produit doit etre installe de facon a
respecter une distance de 36 cm entre l'antenne emettrice et les personnes.
Antenn externe
Utiliser uniiquement les antennes approuvees par le fabricant. L'utilisation
d'autres antennes peut conduire a un niveau de rayonnement essentiel ou non
essentiel depassant les niveaux limites definis par FCC/IC, ce qui est interdit.
Procedure d'installation
Consulter le manuel d'utilisation.
Warning: Please carefully select the installation position and make sure that
the final output power does not exceed the limit set force in relevant rules. The
violation of the rule could lead to serious federal penalty.
Warning: Avertissement: Choisir avec soin la position d'installation et
s'assurer que la puissance de sortie ne depasse pas les limites en vigueur. La
violation de cette regle peut conduire a de serieuses penalites federales.
ExtremeWiNGTM Access
Points
Quick Reference
P/N 37113 AP-7632-680B40-US
P/N 37114 AP-7632-680B40-WR
Notice
Copyright © 2017 Extreme Networks, Inc. All Rights Reserved.
Legal Notices
Extreme Networks, Inc., on behalf of or through its wholly-owned subsidiary,
Enterasys Networks, Inc., reserves the right to make changes in specifications
and other information contained in this document and its website without
prior notice. The reader should in all cases consult representatives of Extreme
Networks to determine whether any such changes have been made.
The hardware, firmware, software or any specifications described or referred
to in this document are subject to change without notice.
Trademarks
Extreme Networks and the Extreme Networks logo are trademarks or
registered trademarks of Extreme Networks, Inc. in the United States and/or
other countries.
All other names (including any product names) mentioned in this document
are the property of their respective owners and may be trademarks or
registered trademarks of their respective companies/owners.
For additional information on Extreme Networks trademarks, please see:
www.extremenetworks.com/company/legal/trademarks/
Documentation & Support
For product support, including documentation, visit:
www.extremenetworks.com/support/
Operational Description of Antenna
Configuration and RF Output Power Setting
Per KDB 353028 D01 Antennas Part 15 Transmitters v01 requirement, Applications must
contain an exhibit listing each antenna, the antenna gain, antenna type, and antenna
manufacturer/vendor and output power that can be used for the device, that the info
listed below are correct and represent the product in consideration under this filing.
Regulatory and Compliance Information
Safety Guidelines
This section contains notices that are intended to protect your personal safety and
prevent damage to the equipment.
Qualified Personnel:
Federal Communications Commission (FCC) Notice
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Industry Canada Notice
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le
dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit
accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un
fonctionnement indésirable.
Caution :
1 The device for operation in the band 5150-5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
2 The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall
be such that the equipment still complies with the e.i.r.p. limits specified for point-to-
point and non-point-to-point operation as appropriate; and
3 Users should also be advised that high-power radars are allocated as primary users
(i.e. priority users) of the bands 5650-5850 MHz and that these radars could cause
interference and/or damage to LE-LAN devices.
Electrical Hazard: Only qualified personnel should perform installation
procedures. Within the context of the safety notes in this documentation,
qualified persons are defined as persons who are authorized to commission,
ground and label devices, systems, and circuits in accordance with established
safety practices and standards. A qualified person understands the
requirements and risks involved with installing outdoor electrical equipment in
accordance with national codes.
Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
Warning: FCC Radiation Exposure Statement: This equipment complies with
FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 31cm
between the radiator & your body.
Avertissement:
1 les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement
pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable
aux systèmes de satellites mobiles utilisant les mêmes canaux;
2 le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 à 5
850 MHz) doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point
à point et l’exploitation non point à point, selon le cas;
3 De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de
haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité)
pour les bandes 5650-5850 MHz et que ces radars pourraient causer du brouillage et/
ou des dommages aux dispositifs LAN-EL.
European Waste Electrical and Electronic Equipment
(WEEE) Notice
In accordance with Directive 2012/19/EU of the European Parliament on waste
electrical and electronic equipment (WEEE):
1 The symbol above indicates that separate collection of electrical and electronic
equipment is required.
2 When this product has reached the end of its serviceable life, it cannot be disposed of
as unsorted municipal waste. It must be collected and treated separately.
3 It has been determined by the European Parliament that there are potential negative
effects on the environment and human health as a result of the presence of hazardous
substances in electrical and electronic equipment.
4 It is the users’ responsibility to utilize the available collection system to ensure WEEE
is properly treated.
For information about the available collection system, please contact Extreme
Customer Support at +353 61 705500 (Ireland).
Hazardous Substances
This product complies with the requirements of Directive 2011/65/EU of the
European Parliament and of the Council of 8 June 2011 on the restriction of the
use of certain hazardous substances in electrical and electronic equipment.
Detachable Antenna Usage
This radio transmitter (IC: 4141B-AP3915E / Model: AP7632) has been approved by ISED
to operate with the antenna type listed below with maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 4141B-AP3915E / Model: AP7632) a été approuvé par ISED
pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est
supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
Warning: IC Radiation Exposure Statement: This equipment complies with
ISED radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 36cm
between the radiator & your body.
Warning: Déclaration d'exposition aux radiations: Cet équipement est
conforme aux limites d'exposition aux rayonnements ISED établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec
un minimum de 36 cm de distance entre la source de rayonnement et votre
corps.
Approved Antenna(s) list:
Declaration of Conformity in Languages of the European
Community
English Hereby, Extreme Networks, declares that this Radio LAN device is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Finnish Valmistaja Extreme Networks vakuuttaa täten että Radio LAN device
tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen mukainen.
Dutch Hierbij verklaart Extreme Networks dat het toestel Radio LAN device
in overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
Bij deze verklaart Extreme Networks dat deze Radio LAN device
voldoet aan de essentiële eisen en aan de overige relevante
bepalingen van Richtlijn 1999/5/EC.
French Par la présente Extreme Networks déclare que l'appareil Radio LAN
device est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE.
Par la présente, Extreme Networks déclare que ce Radio LAN device
est conforme aux exigences essentielles et aux autres dispositions de
la directive 1999/5/CE qui lui sont applicables.
Swedish Härmed intygar Extreme Networks att denna Radio LAN device står I
överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Danish Undertegnede Extreme Networks erklærer herved, at følgende udstyr
Radio LAN device overholder de væsentlige krav og øvrige relevante
krav i direktiv 1999/5/EF.
German Hiermit erklärt Extreme Networks die Übereinstimmung des "WLAN
Wireless Controller bzw. Access Points" mit den grundlegenden
Anforderungen und den anderen relevanten Festlegungen der
Richtlinie 1999/5/EG.
Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Extreme Networks ∆ΗΛΩΝΕΙ ΟΤΙ Radio LAN
device ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ
ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/
ΕΚ.
Icelandic Extreme Networks lysir her med yfir að thessi bunadur, Radio LAN
device, uppfyllir allar grunnkrofur, sem gerdar eru i R&TTE tilskipun
ESB nr 1999/5/EC.
Italian Con la presente Extreme Networks dichiara che questo Radio LAN
device è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.
Spanish Por medio de la presente Extreme Networks declara que el Radio LAN
device cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Portuguese Extreme Networks declara que este Radio LAN device está conforme
com os requisitos essenciais e outras disposições da Directiva 1999/5/
CE.
Malti Hawnhekk, Extreme Networks, jiddikjara li dan Radio LAN device
jikkonforma mal-htigijiet essenzjali u ma provvedimenti ohrajn
relevanti li hemm fid-Dirrettiva 1999/5/EC.
P/N 9035136-02

Navigation menu