Extreme Networks SA201 Open networking adaptor IoT User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3995592
Application ID	s6W4+Y/1FxWMrY8d9mW6TA==
Document Description	Users Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	71.29kB (891094 bits)
Date Submitted	2018-09-07 00:00:00
Date Available	2018-09-11 00:00:00
Creation Date	2004-12-17 11:57:16
Producing Software	Acrobat Distiller 18.0 (Windows)
Document Lastmod	2018-09-03 15:22:00
Document Title	QXO-SA201 Extreme Networks Defender Adapter Quick Reference
Document Creator	FrameMaker 2017
Document Author:	Extreme Networks

Installing the Extreme Networks SA201
Defender Adapter
SA201 Side Ports
Figure 1
Table 3 Contents of the SA201 Box
SA201 Ethernet port and 12V DC Power Supply
Overview of the SA201
The SA201 is an Open Networking Adapter IoT (Internet of
Things) solution that is used to securely deploy IoT devices.
SA201 adapter can be used to provide proxy service for the
Defender Adapter Application. SA201 has a full layer 1-7
visibility and can be paired 1:1 with a medical or IoT device
in a hospital or campus environment.
Note: The SA201 requires a minimum base firmware of
Defender 3.1.
For Cloud, the minimum base firmware is ExtremeCloudTM
Appliance 4.26.02.
The SA201 adapter has the following specifications:
• Primarily designed to support and securely manage IoT
devices by reporting any abnormal flow to the
Application and preventing the IoT devices from
launching malware attacks.
• Two RJ45 Gigabit Ethernet ports:
– One network port with Cloud icon
– One device port that reads DEVICE
• LEDs: 4 on both faces (Figure 2)
– The LEDs are located on both faces of the adapter to
allow visibility from both sides.
• Power: PoE and 12V DC Power Supply.
• Temperature
– Operating Temperature: 0°C to +35°C (32°F to 95°F)
– Non-operating Temperature: -40˚C to +70˚C (-40°F to
158°F)
• Enclosure: Plastic material with soft rubber on two
edges, for shock resistance and friction.
• Enabled for ExtremeCloudTM support.
The SA201 uses Power over Ethernet (PoE) as follows:
Table 1 Power Sources
Power Source
Power over Ethernet
(PoE)
Optional Power Source
Description
Power is provided through the RJ45
Ethernet port (LAN1 port) on the Network
side of the SA201 adapter. When the
SA201 adapter is powered by 802.3AT, the
DEVICE port is capable of power sourcing
(refer Figure 1).
Item
M4 wood screws; the head may be up to 2.5 mm
thick. Screw dimension: 3.5x25.4mm.
Screw-in wall anchors
Note: Before mounting the SA201, read the Safety
Guidelines section.
Mounting and Connecting the SA201
Use these instructions as guidelines for mounting and
connecting the SA201 easily and safely.
LEDs
Electrical Hazard: Use ESD (Electrostatic Discharge)
protection wrist strap when installing the SA201 adapter.
There are LEDs on four of the six sides of the SA201 unit.
Figure 2 shows the LEDs located on the front cover of the
adapter.
Figure 2
LEDs on Front Cover
Mounting the SA201 on a Table
To mount the SA201 adapter on a table:
1 Place the SA201 adapter on a table close to the Device
and Network cables.
2 Connect the Device and Network LAN cables.
Figure 3
Number
Description
ESD-protective wrist strap
(purchased separately)
1 Mark the two hole centers. The two screw centers should
be 3.6” apart.
2 For drywall/plasterboard walls, when using plastic
anchors, drill two holes using a drill bit of 6mm or 1/4”
diameter.
3 For wood walls, when using only wood screws, drill two
holes using a drill bit of 3mm or 1/8” diameter.
4 Screw in the respective screws into the holes.
5 Attach the SA201 adapter to the screws.
6 Rock it back and forth to ensure that the unit is secured
in place.
7 Connect the LAN cables.
Figure 5
Mounting the SA201 to a Wall
Mounting the SA201 on a Table
Connecting the SA201 unit to the Network
Power
Caution: Connect the equipment only to an outlet with
grounding for additional safety against electric shock when
using the protective earthing conductor.
Status
Mounting to a Shelf
For detailed installation information about the SA201, see
the Extreme Networks SA201 Installation Guide.
Power Connections
Quantity
PSE Client Port
Table 2
IoT (BLE or 802.15.4)
SA201 LED Status
LED Icon
LED Color
Description
Power
GREEN
Normal power status
Status
GREEN
Normal operational status
AMBER
Non-operational status
GREEN
Normal operational status
(DEVICE port is capable of
providing PoE)
OFF
Non-operational status
PSE Client
Port
IoT (BLE)
BLUE
Indicates BLE is enabled
OFF
Non-operational status
1 Place the SA201 at a secure position close to the
corresponding equipment.
2 Secure the unit using wire ties.
3 Connect the LAN cables.
Mounting the SA201 to a Wall
You can mount the SA201 adapter using the wall mount
keyholes in the back of the unit. The keyholes are
bidirectional and let the adapter to be mounted in either
direction.
Figure 4
Electrical Hazard: To reduce potential safety issues, only
the AC adapter provided with the product, a replacement
AC adapter provided by the agency, or an AC adapter
purchased separately as an accessory from the agency
must be used with the product.
Connect the LAN 1 cable to the RJ45 Ethernet Port on the
left of the 12V DC port.
Figure 6
Connecting the SA201 to the Network
Tools required
Description
External 12V DC Power Supply The SA201 can also be powered
(optional; #30512 - PWR 12VDC, by an external DC power supply
2A, 2.1mm x 5.5mm connector) plugged into an AC source. Plug
the supply’s input jack into the
DC-In port.
Note: If the SA201 adapter is plugged into the PoE switch
port and the 12V DC-In port, the unit will use the DC input
power source over the PoE port.
For detailed information about Network Speed and Link
Activity, see the Extreme Networks SA201 Installation
Guide.
Verifying the SA201 Box Contents
Verify the contents of the box as listed in the following
table:
Table 3 Contents of the SA201 Box
Quantity
Item
Number
Description
SA201 Quick Reference
Flat-head screwdriver
M4 screws and wall anchors
The following hardware is included:
SA201 Adapter
Optionally, you can use the 12V DC External power supply.
PoE sourcing is not available when the unit is powered
using the 12V DC power supply.
For more information, see the Extreme Networks SA201
Installation Guide.
Regulatory and Compliance Information
Federal Communications Commission (FCC) Notice:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority
to operate this equipment
2 When this product has reached the end of its serviceable life, it cannot be
disposed of as unsorted municipal waste. It must be collected and treated
separately.
3 It has been determined by the European Parliament that there are
potential negative effects on the environment and human health as a
result of the presence of hazardous substances in electrical and electronic
equipment.
4 It is the users’ responsibility to utilize the available collection system to
ensure WEEE is properly treated.
For information about the available collection system, please contact
Extreme Environmental Compliance at Green@extremenetworks.com.
Hazardous Substances
This product complies with the requirements of Directive 2011/65/EU of the
European Parliament and of the Council of 8 June 2011 on the restriction of
the use of certain hazardous substances in electrical and electronic
equipment.
Declaration of Conformity in Languages of the European Community
Hereby, Extreme Networks, Inc. declares that the radio equipment type
Wireless LAN Access Point is in compliance with Directive 1999/5/EC. The
full text of the EU declaration of conformity is available at the following
Internet address: http://www.extremenetworks.com/
Note: Changes or modifications made to this device which are not
expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Extreme Networks
Defender Adapter
Quick Reference
P/N 39505
QXO-SA201-FCC
.This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Warning: FCC Radiation Exposure Statement: The antennas
used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be colocated or operating in conjunction with another antenna or
transmitter.
Industry Canada Notice:
This device complies with RSS-247 of the Industry Canada Rules. Operation
is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-247 d'Industrie Canada
applicable aux appareils radio exempts de licence. Son fonctionnement est
sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de
brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage
reçu, y compris un brouillage susceptible de provoquer un fonctionnement
indésirable.
For Mobile Device Usage
Warning: Radiation Exposure Statement: This equipment
complies with ISED radiation exposure limits set forth for
an uncontrolled environment. This equipment should be
installed and operated with greater than 20cm between the
radiator & your body.
Warning: Déclaration d'exposition aux radiations: Cet
équipement est conforme aux limites d'exposition aux
rayonnements ISED établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé à plus
de 20 cm entre le radiateur et votre corps.
Safety Guidelines
This section contains notices that you must adhere to ensure your personal
safety and to prevent any damage to the equipment.
Caution: The unit and all interconnected equipment must be
installed indoors within the same building, including all PoEpowered network connections as described by Environment A of
the IEEE 802.3af standard.
European Waste Electrical and Electronic
Equipment (WEEE) Notice
NCC Statement
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許
可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及
干擾合法通信；經發現有干擾現象時，應立
即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線
電通信。
低功率射頻電機須忍受合法通信或工業、科
學及醫療用電波輻射性電機設備之干擾。
在 5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限
於室內使用。
電磁波曝露量 MPE 標準值 1mW/cm2，送測產品實測值
為 0.315 mW/cm2
In accordance with Directive 2012/19/EU of the European Parliament on
waste electrical and electronic equipment (WEEE):
1 The symbol above indicates that separate collection of electrical and
electronic equipment is required.
Notice
Copyright © 2018 Extreme Networks, Inc. All Rights Reserved.
Legal Notices
Extreme Networks, Inc. reserves the right to make changes in specifications and
other information contained in this document and its website without prior notice.
The reader should in all cases consult representatives of Extreme Networks to
determine whether any such changes have been made.
The hardware, firmware, software or any specifications described or referred to in
this document are subject to change without notice.
Trademarks
Extreme Networks and the Extreme Networks logo are trademarks or registered
trademarks of Extreme Networks, Inc. in the United States and/or other countries.
All other names (including any product names) mentioned in this document are
the property of their respective owners and may be trademarks or registered
trademarks of their respective companies/owners.
For additional information on Extreme Networks trademarks, please see:
www.extremenetworks.com/company/legal/trademarks/
Documentation & Support
For product support, including documentation, visit: www.extremenetworks.com/
support/
P/N 9035972-01

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
Page Mode                       : UseNone
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Format                          : application/pdf
Creator                         : Extreme Networks
Title                           : QXO-SA201 Extreme Networks Defender Adapter Quick Reference
Create Date                     : 2004:12:17 11:57:16Z
Creator Tool                    : FrameMaker 2017
Modify Date                     : 2018:09:03 15:22+08:00
Metadata Date                   : 2018:09:03 15:22+08:00
Producer                        : Acrobat Distiller 18.0 (Windows)
Document ID                     : uuid:703991f4-3e74-4b4d-be2a-d3f927febb32
Instance ID                     : uuid:efdf4776-2c0c-4530-839f-6ace9b0962e3
Page Count                      : 2
Language                        : en
Author                          : Extreme Networks

EXIF Metadata provided by EXIF.tools