FISHERPAYKEL Dishwasher Manual L0906175
DD24DCX6-88527A DD24DCX6-88527A FISHER & PAYKEL DISHWASHER - Manuals and Guides L0906175 View the owners manual for your FISHER & PAYKEL DISHWASHER #DD24DCX688527A. Home:FISHER & PAYKEL:/ Dishwasher Parts:FISHER & PAYKEL dishwasher parts:#DD24DCX688527A FISHER & PAYKEL dishwasher parts:#DD24DCX688527A FISHER & PAYKEL dishwasher manual
User Manual: FISHERPAYKEL FISHERPAYKEL Dishwasher Manual FISHERPAYKEL Dishwasher Owner's Manual, FISHERPAYKEL Dishwasher installation guides
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
(1,1) -1 - 599618C DD24D install A2 USCA.indd 15/4/09 10:01:39 AM Importand SAVE THESEINSTRUCTIONS lh_÷ mocDIs shown in thLs docum_÷nt w_÷bsit_÷ www.fish_÷rpoykd.comor mc2y not b_÷c2vc2ilc2bl_÷in c_ll mc2rk_÷ts c_nd c2r_÷.subj_÷ct to chc2ng_÷ c2t c2ny tim_÷, f::or curr_÷nt cDtoi/s c2bout mocDI c2nd sp_÷cificotion c2vc2ilc2bility in your country, pl_÷c2.s_÷ go to our contoct your /ocol FTsh_÷r& Poy£÷ld_÷ol_÷r. SAFETY AND WARNINGS Important installation Electrical hazard Before installing breaker. If permanently the DishDrawer GROUNDmNG safety instructions! of this DishDrawer Be sure to leave the DishDrawe¢ _, remove the house fuse or open the circuit installation must comply A t the completion connecting the DishDrawe¢ _ unplugged. _, be sure the power is isolated and This appliance must be grounded. [n the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for eBectric current. This appBiance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances. WARNmNG - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded. may result in electrical shock or death. Take care = panel edges are sharp. Failure to use caution could result in injury or cuts. materials connections electrician to ensure that The DishDrawer_ The switched supplied with for indoor are turned and electrical skills. and electricity regulations. the Installer must perform outlet the DishDrawer% use only. OFF. It is the responsibility each installation MUST be installed power complies with t_ a_wf_rfuture of the plumber and all Codes and Regulations. rem_val must be outside the DishDrawer fr_m the enc_sure _ cavity if service so that it is accessible is required. after installation. Care should the power be taken supply damage Make from when the appliance is installed or removed to reduce the likelihood of damage cord. _ is to be relocated water from one installation to another it must be kept upright to avoid spillage. sure only new hoses are used for connection (supplied with DishDrawerC% Old hoses shouM not be reused. to install If the product boat the DishDrawer is installed or mobile technician_ Cut hazard _ installation, Ensure all water Failure advice local building _ is manufactured Do not modify the power supply plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use an extension cord, adapter plug or multiple outlet box. this with your all packaging If the DishDrawer to follow basic mechanical the Customer. of the DishDrawer This DishDrawer [f the DishDrawer is installed as a permanently connected appliance: GROUNDmNG INSTRUCTIONS °This appliance must be connected to a grounded metal, permanent wiring system, or an equipment=groounding conductor must be run with the circuit conductors and connected to the equipment°grounding terminal or lead on the appliance. Failure with Final Check List. Remove mNSTRUCTmONS _ requires these Instructions facility travel _ correctly in a motor containing to the location could vehicle, the product invalidate boat or similar any warranty mobile facility, to the service shop at your of the product. or liability claims. you must bring expense the vehicle, or pay the service to I (1,2) -1- 599618C DD24D install A2 USCA.indd 15/4/09 10:01:39 AM PRODUCT D MENS ONS [ ,_OJ/ [[(?1 (]'J (1:)?; OFJ/JU 1: [J(?[ _? J_ C; 'J (?1) _E Product dimensions (inches (mm)) _ m_ _ $, Cabinetry dimensions A ove[al heght_ofprodu t B overaJl wdth C overall depth of product (exd curvature/handJe) of product c_- c_ ° 321/4 -34%" (819.5- 879.5) 321/4 -345/d ' (819.5- 879.5) 321/4 -34%" (819.8- 879.5) 23 946"(599) 23 946"(599) 22 _d' (570) 23 946"(599) 22 _d' (570) _- A i nsde heig ht of cavity 22 _d' (570) B inside width of cavity i "_sde depth of avity a depth of drawe_ (open) (exc[curvaturdha/die) 21 sad' (538) 21 _6" (538) 21 34d' (538) C E heght_of chassis 31 7/8"(809) 31 7/8"(809) 31%"(8o9) D heght E heightoftoekickspace F height range of eveJling fe_-_t G depth of chassis (incLtrimseal) m depth of drawer front panel (exd.curvature,!_andle) I depth of curvature o_ handle J depth of toekick K height of upper @awe font h heightof owerdrawerfront M heghtofinstallation N heght of drawer fronts bracke sots(onlopofchasss) 2 3/8"(60) 2 3/8"(60) 2 s/8"(60) 21 3A"(552) 21 Y4"(552) 21 3A"(552) 1H6"(18) "/id'(18) "/i?'(18) 7A6"(11) 1%" (41) n/a 2 - 4 SAo"(50 - 110) 2 - 4 sAo"(50- 11o) 2 % - 5"(67 - 127)_* 151/2" (394) 15 11A6"(398) 14"(356) 14"(356) 15 1¼6"(398) min 12 1/4"(311.5)min ¼6" (2) lk6" (2) ¼6" (2) 29 %6" (751) 30 1A6"(764) 28 _A"(717.5) rain C} assishe ghts nchde bracket sots Besst} e Tbekick Pa_e[ _ ckness(Mr mira Panel h cknessus_g tt_esupplied screwsis W' (9 ram)), Note: lot Prr:,finishedFJa_door models, height from top of hande _o_op of drawe --2 V_"(64 mm) (inches (mm)) _ m _ c_- (rlSkk,) of adjace t_ cabinetry Minimum clearances (inches(mm)) 32 SA6- 34 sA" (820- 882.5) 32 sA6 - 34 sA" (820- 882.5) 32 sA6 - 34 Y4" (820- 882.5) 23 s/8" (600) 23 s/8"(600) 23 s/8"(600) 22 7/8"(580) 22 7/8"(580) 22 7/8"(580) 30" (762) 315A6-65A6"(lO0-160) 30" (762) 315A6-65A6"(lO0-160) min. 28 s/d' (720) 315A6-65A6"(lO0-160) L(2,1) -1 - 599618C DD24D install A2 USCA.indd 15/4/09 10:01:39 AM PARTS SUPPUED Drain hose support (1) Drain hose joiner (1) Wire clip (2) Clamp (1) Top mounting brackets (2) Phillips 16 mm screws (9) Washer (1) Moisture protection tape (1) (to prevent moisture d_m_ge) Edge protector (1) (if serviceshole partition is metal) Hexagonal socket (2) (long & short) Prefinished toekick (I) white or black If the Drain hose(s) supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hose(s) by 1I' 10"(3.6 m).The kit is available from the nearest Fisher& Paykel Authorized Service Agent, or Toll free 1.888.936.7872 or www.fisherpaykekcom. CAVKY PREPARATION Importand Besure the edgesof the serviceshole are smooth or covered, ff the services hole is through a metal partition the hole must be protected with the Edge If no side partition, use a brace for securing. protector supplied to prevent damage to the power cord or hoses. These marks indicate mounting bracket screw locations $6 Preferred position. If adequate clearance, services hole can be higher to clear toekick space. If hole is higher, ensure drain hose(s) are routed straight into the waste connection. (10 mm) ta Water Connection Recommended HOT (Maximum 140°F/60°C). Supplied hose to suit 3/8" (9 ram) male compression fitting. Water Pressure Water softener Other models models Max Min 1 MPa (145 psi) 0.1 MPa (14.5 psi) 1 MPa (145 psi) 0.03 MPa (4.3 psi) max. 17 11A6" Drains will need to be separated acceptability with your local rabbi to satisfy kosher in respect requirements. to kosher We suggest you confirm (450 mm) max. o 1 1/2" installations. Water supply (38 mm) \ J i _min. 7 Ys" Drain hose Inlet hose Power cord (excl.plug) 78 ½" (2000mm) 70 ½" (1800 ram) 64 ¾" 49" (1650 mm) (1250 ram) z?i\t Left hand side Right (200 mm) hand side 29 ½" 27 ½" 110-120VAC (750 mm) (700 mm) max. 15 A L(2,2) -1 - 599618C DD24D install A2 USCA.indd 15/4/09 10:01:39 AM I OPTIONALW HARD WIRING THE PRODUCT Remove the access cover Ensure the drawer is removed and then rotated counterclockwise to prevent kinked hoses. Remove Power supply Access cover Remove knock-out for cable clamp. Fit suitable cable clamp for the conduit and terminate the wiring as shown. Use copper conductors only. Ensure the drawer clips on both sides are reset. c,/...._.,_ © Ensure the drawer is now rotated clockwise back. Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward. (1,1) -2- 599618C DD24D install A2 USCA.indd 15/4/09 10:02:23 AM ROUTETHE HOSESAND MOVE _NTOTHE CAVITY If top mounting brackets are being used, ensure they're securely fitted before sliding product into cavity. Ensure hoses and cord are not kinked or twisted. optional (x2) OR Loosen feet only and _2 take care when pushing _q_' the product into the / cavity that you do not bendthe feet. REMOVETHE DRAWER AND LEVELTHE PRODUCT Ensure product is level and aligning with cabinetry. Using the most appropriate length Hexagonal socket supplied, fully extend levelling feet up to required distance by hand. Ensure the drawer is removed then rotated counter-clockwise to prevent kinked hoses. and Hexagonal socket X4 I (1,2) -2599618C DD24D install A2USCA.indd 15/4/09 10:02:23 AM SECURE THE PRODUCT AND REFIT THE DRAWER The product has three pairs of mountinq brackets: a pair of optional brackets on the top (C) and two pairs of formed brackets in the side of the chassis (A,B). Use at least two out of the three pairs to secure the product. optional Ensure the drawer clips on D/ ........ ,," both sides are reset. C 3A" (19 mm) Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer Ensure the sound insulation is repositioned correctly. runner Ensure the drawer is now rotated clockwise back. _} F_TTHE TOEK_CK Where the toekick meets the bottom of the tub is the cut-off point lmportand D o not overtighten screw. are facing forward. L(2,1) -2- 599618C DD24D install A2 USCA.indd 15/4/09 10:02:23 AM PLUMBING AND DRAINAGE OPTIONS DishDrawer ®with Waste Disposal DishDrawer ® using Air Break with Drain Hose Joiner (_;il} DishDrawer O 1 1/2"(38 If space is limited for fixing, push hose through drain hose support to required height ® and Standpipe mm) If space is limited for fixing, push hose through drain hose support to required height HIGHLOOP min. 6" (150 ram) ! _] 37 3/8" (950 mm) Max. height to top of Air Break (countertop or wall mounted) min. R 8" (200 mm) (200 mm) Fit supplied washer Fit supplied washer Fit supplied washer Ensure hoses are routed straight to joiner. Remove excess hose material if necessary. Ensure hoses / t L(2,2) -2- 599618C DD24D install A2 USCA.indd 15/4/09 10:02:23 AM I F NAL CHECKLIST [] Check all parts are installed. [] Ensure product TROUBLESHOOTING o is level, securely fastened to the cabinetry and opens and closes freely. The DishDrawer ® must be free to fully close with no resistance from the cabinetry. [] [] Ensure any knockouts as fully extended [] If using Plumbing 6"(150 [] have been drilled out and o No lights as possible to prevent the weight of excess hoses. Keep hoses sagging. Any excess length of hose o Water around is a minimum fitted o mm) higher than the drain hose joiner. Turn on the power and water supply. Then press the Power (©) button DishDrawer ® should beep and Wash Programme If product existing o o o o If front Selector Panel press Rinse and close the drawer(s). Start the programme plumbing connections and hoses for leaks. Check washer and panels are misaligned Check the cabinetry is square. Drawer(s) don't dose properly If a problem is obstructing the drawer(s) from closing properly eg sound hoses or drawer latches. occurs, consult the Troubleshooting If after checking section of the User Guide. these points you still need assistance, please refer to the Service & Warranty book for warranty Service Centre, or contact Add three cups of water into the DishDrawer ®.On the Wash Programme is is secured to the cabinetry. Check and relevel product. Check the spray arm is in place and free to rotate. on. Check if Auto Power option is tipping Ensure the product to turn lights and is switched hose clamps are correctly fitted. insulation, [] on and the spray arm(s) are correctly water suppJy and drainage Check connections, side of the high loop. and Drainage OPTION A, ensure the Highloop pressing the Start/Pause with LCD only) come on when the drawer is opened Ensure nothing [] correctly. No water suppJy (® shows on display-models turned high loop not on. light up. [] plate, after the rinse cycle installed or drain hoses not routed Ensure power is connected must not support the DishDrawer ®on.The above the filter and free to rotate. or plugs in drain connection be kept on the dishwasher remaining Check water is connected, has been made. The drain hose joiner should a half turn after seal contact. drain connection [] properly o Ensure inlet hose to water supply has rubber washer fitted and is tightened further Excessive water Check for kinked drain hoses or blocked waste connection, us through details and your nearest Authorized our website, www.fisherpaykel.com. by (_H) button. After the Rinse programme has finished, ensure machine has run and drained correctly. [] Check water supply and drainage connection for leakage. Repeat for each drawer. www.fisherpaykel.com www.fisherpaykel.ca 599618C US CA 04.09
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 8 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Sun Jun 21 04:13:05 2009 Author : Title : Subject :EXIF Metadata provided by EXIF.tools