FLYTECH TECHNOLOGY K936C43 Terminal Hardware System User Manual K936 C43 V1 0

FLYTECH TECHNOLOGY CO., LTD Terminal Hardware System K936 C43 V1 0

User manual

Version 1.0 June 2011 Bedside Terminal Hardware System User Manual
iCopyright 2011 June All Rights Reserved Manual Version 1.0 Part Number: 3LMKK9360110 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without the prior written consent of the manufacturer. TRADEMARK Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation. Microsoft® and Windows® are registered trademarks of Microsoft Corporation. Other trademarks mentioned herein are the property of their respective owners. Safety IMPORTANT SAFETY INSTRUCTIONS 1. To disconnect the machine from the electrial power supply, turn off the power switch and remove the power cord plug from the wall socket. The wall socket must be easily accessible and in close proximity to the machine. 2. Read these instructions carefully. Save these instructions for future reference. 3. Follow all warnings and instructions marked on the product. 4. Do not use this product near water. 5. Do not place this product on an unstable cart,stand,or table.The product may fall, causing serious damage to the product.
ii 6. Slots and openings in the cabinet and the back or bottom are provided for ventilation;to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered.The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.This product should never be placed near or over a radiator or heat register,or in a built-in installation unless proper ventilation is provided. 7. This product should be operated from the type of power indicated on the marking label.If you are not sure of the type of power available, consult your dealer or local power company. 8. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. 9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. CE MARK This device complies with the requirements of the EEC directive 2004/108/EC with regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage Directive”. FCC This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. UL
iiiThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help CAUTION ON LITHIUM BATTERIES There is a danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. Battery Caution Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery according to the local disposal instructions. Safety Caution Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related legislation, peripherals shall be 4.7.3.2 "Materials for fire enclosure" compliant. 4.7.3.2 Materials for fire enclosures For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material of a FIRE ENCLOSURE, in the thinnest significant wall thickness used, shall be of V-1 CLASS MATERIAL or shall pass the test of Clause A.2. For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all STATIONARY EQUIPMENT, the material of a FIRE
iv ENCLOSURE, in the thinnest significant wall thickness used, shall be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1 LEGISLATION AND WEEE SYMBOL 2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling and disposal of electric and electronic devices and their components. The crossed dustbin symbol on the device means that it should not be disposed of with other household wastes at the end of its working life. Instead, the device should be taken to the waste collection centers for activation of the treatment, collection, recycling and disposal procedure. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
vRevision History Changes to the original user manual are listed below: Version Date Description 1.0 June 2011 Initial release
vi Table Contents 1 Item Checklist....................................7 1-1 Standard Items ..........................................................7 2 System View ......................................8 2-1 Front View .................................................................8 2-2 Rear View..................................................................9 2-3 I/O View...................................................................10 3 Driver Installation ............................ 11 3-1 Driver List ................................................................11 3-2 Chipset Driver Installation........................................12 3-3 VGA Driver Installation ............................................13 3-4 Audio Driver Installation...........................................16 3-5 10/100/1000Mb LAN Driver Installation...................17 3-6 POSTouch Driver Installation...................................18 4 System Assembly............................22 4-1 HDD Replacement...................................................22 5 Peripheral Installation.....................23 5-1 Phone Set Installation..............................................23 5-2 Arm Installation........................................................23 5-3 MSR Installation ......................................................24 6 Specification....................................25 7 Jumper Settings ..............................27 7-1 C43 V1.0 motherboard ............................................27
71 Item Checklist Take the system unit out of the carton. Remove the unit from the carton by holding it by the foam inserts. The following contents should be found in the carton: 1-1 Standard Items Driver CD Manual Power Adapter Power Cable System Phone Module
8 2 System View 2-1 Front View Number Description 1 Build-in camera 2 Build-in Microphone 3 TV Key pad (power, volume, channel, and nurse call button) 4 Smart card reader slot 5 Phone set holder ① ② ③ ④ ⑤
92-2 Rear View Number Description 1 Speakers 2 VESA Holes 3 Rear I/O (from left to right: RJ48, USBx2, DC-IN, Display port , LAN Connector)4 HDD door 5 MSR Slot (Option) ① ② ③ ④ ⑤
10 2-3 I/O View Number Description 1 LAN (RJ45) 2 USB x 2 3 SCSI Connector 4 USB x 1 5 Phone Jack (RJ11) 6 Audio Line-out 7 Audio Line-in 8 Audio MIC-IN 9 RFID sensor ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨
113 Driver Installation 3-1 Driver List C43 Driver List Folder/File File Description <CD>:\ K936_C43.htm Driver List <CD>:\COMMON\INTEL\Chipset\i9xx Chipset Driver <CD>:\COMMON\INTEL\VGA\GMA3150 VGA Driver <CD>:\COMMON\Audio\Realtek_HD_Codec-AEC_enable Audio driver with AEC enable<CD>:\COMMON\ POS_Touch POSTouch Driver <CD>:\COMMON\Lan_driver\Intel 10/100/1000Mb LAN Driver -The following procedures are for Windows 2000/XP, other platforms are similar.
12 3-2 Chipset Driver Installation a. Click “Windows” in the Driver List menu of K936 C43 and then doule-click “v9.1.1” b. Double-click “infinsts911_autol.exe” on the My computer window. c. Click the “Next” button on the Welcome window. d. Click the “Yes” button on the License Agreement window. e. Click the ”Next” button on the Readme Information window. f. Click the “Finish” button and restart your system.
133-3 VGA Driver Installation a. Click “WinXP” of “VGA” section in the Driver List menu and then double-click “v14.37.50.4.5260” b. Double-click “winxp.exe” on the My computer window.. c. Click the “Next” button on the Intel(R) Chipset Graphics Driver Software- Install Shield(R) Wizard dialog. d. Click the “Next” button on the Intel(R) Graphics Media Accelerator Driver dialog.
14 e. Click the “Yes” button on the Intel(R) Graphics Media Accelerator Driver dialog. f. Click “Next” button on the Intel(R) Graphics Media Accelerator Driver dialog. g. Click “Next” button on the Intel(R) Graphics Media Accelerator Driver dialog. h. Select “Yes, I want to restart my computer now” and click the “Finish” button on the Intel(R) Graphics Media Accelerator Driver dialog. For WinXP and POSReady 2009 upgrade a. Click “WinXP” of “VGA” section in the Driver List menu.
15b. Click the “Next” button on the Software Update Installation Wizard dialog. c. Click “I Agree” and click “Next” button on the Software Update Installation Wizard dialog. d. Click the “Finish” button on the Software Update Installation Wizard dialog to restart your system.
16 3-4 Audio Driver Installation a. Click “Windows” of the “Audio” section in the Driver List menu. b. Double-click R254+AEC” on the My Computer window. c. Double-click “Setup.exe” on the My Computer window. d. Click “Next” button on the Realtek Audio Setup window. e. Click “Finish” button on the Realtek Audio Setup window.
173-5 10/100/1000Mb LAN Driver Installation a. In the “intel” section, click on “Windows” and click on “Alpha” b. Double-click “v15.6” c. Double-click Setup.exe d. Click the Finish button on the Maintenance Complete window. e. Click the OK button and restart your system. v15.6
18 3-6 POSTouch Driver Installation a. In the “Touch Screen auto…” section, click “Windows”. b. Click “Install Touch Driver” on “FT Touch Auto Install V1.0.4.1” window to detect the touch type in your system. c. “FT Touch Auto Install” program will detect what touch type and interface being installed on the system. d. Click ”Next”. e. Select ”I agree…” and click ”Next”. f. Select the installation folder for the touch utility driver and click ”Next”.
19 g. Select the shortcut folder for the touch utility driver and click ”Next”. h. Click ”Next”. i. Click ”Next”. j. The computer is installing the touch driver k. Click ”Continue Anyway” button. l. The serial ports are scanned for a touch device. The Touch panel is on COM5.
20 m. Click ”Finish”. n. Click ”OK” to restart the computer and finish the touch utility installation. o. The computer has restarted. Click on the ”Start” button, select “Programs”, then select ”Touchutility”. p. Select the Device tab. q. Click on the 3 points or the 9 points calibration button. r. Follow the instructions on the screen to do the calibration of the touch panel
21 s. Touch anywhere on the screen to save the calibration.
22 4 System Assembly 4-1 HDD Replacement a. Find the HDD door at the rear right side of the system and loosen the screws(x2) b. To replace the HDD, push the HDD outwards as picture shown.
235 Peripheral Installation 5-1 Phone Set Installation a. Loosen the screws(x2) to open the cable cover. b. Slide the phone module into the phone set holder and connect the phone cable to the connector on the phone module. c. Connect the other end of the phone cable to the connector on the system. 5-2 Arm Installation a. Connect the cables to the system b. Tighten the screws(monitor screwx4) Note: Only use concrete walls to fix the Arm (and wall box) to.
24 5-3 MSR Installation a. Connect the MSR cable to connector to the on system side. b. Fasten screws(x2) to secure the module.
256 Specification Model K936 Motherboard C43 V1.0 CPU Intel pineview D525 1.8G L2 1M, Dual core Core Logic CPU with Graphic built-in + ICH 8M System Memory 2 x DDR3 DIMM up to 4GB FSB800Mhz Graphic Memory Intel GMA 3150 share system memory 256MB LAN controller / phy Intel WG82583V / Intel WG82567V Audio controller Realtek ALC 662-GR HD codec I/O controller Winbond W83627UHG BIOS AMI LVDS Interface Mstar TSUMU18ER-1 Touch controller Idealtek local touch (RS232) Touch True flat- 5 wire-RS232 / DMR-USB Watch Dog Timer Hardware WDT 2nd VGA Display port connector Display size 15.6" Resolution 1366 X768 Brightness 250 nits Storage HDD 1x 2.5" SATA HDD, pSSD Expansion Mini PCIe 2 x PCI-e full size slot for video decoder card / RCA module Buttom I / O Power button 1 Handset 1xRJ11(4 pin) Remote 1x SCSI 26pin, USB 3 (USB 2.0) LAN (2nd LAN) 1xRJ45 (with 100/1000,LED indicator) Reset button 1, button can be pressed by probe MIC-in 1(Auto-detect, GPIO), in external IO Line-out 2(Auto-detect, GPIO), in external IO Vertical I / O Power DC Jack USB 2 (USB 2.0) LAN 1 x RJ 45 (with 100/1000) 2nd Display 1 x Display port Nurse call 1 x RJ 48 Membrane
26 Power button 1xpower button(GPIO) Channel adjustment 1xChannel up, 1xChanngel down(GPIO) Volume 1xvolume up, 1xvolume down(GPIO) Nurse call 1x Nurse call (GPIO) Certificate EMC & Safety FCC Class B, CE, LVD / UL 60950 / UL 60601 Environment Operating Temperature 0°C ~ 35°C (32°F ~ 104°F) Storage Temperature -20°C ~ 55°C (-4°F ~ 140°F) Operating Humidity 20% - 80% RH non condensing Storage Humidity 20% - 85% RH non condensing Weight 4 kg (without handset / cradle) Communication & peripherals Build in Microphone In left side of Web cam with GPIO TV Tuner (Analog RCA,optional) RCA connector Smart IC card reader Comply with ISO 7816-1,2,3,T=1 and T=0 protocol RFID module Internal USB connection MSR (optional) 3 track (PS2) Handset module VOIP phone Cradle, mechanical switch Webcam 1.3M web cam(USB) with web cam door Bedside light blue color Video decoder card mini PCIe video decorder card 2D scanner(Optional) 2D scanner Operating System OS Support Windows® XP Professional, Windows Embedded POSReady 2009, Windows XP Embedded, Windows XP Professional for Embedded, Windows 7, Linux
277 Jumper Settings 7-1 C43 V1.0 motherboard 7-1-1 Motherboard Layout
28 7-1-2 Connectors & Functions Connector Function CN3 USB Port For Web Cam CN4 Speaker & MIC CN5 Cradle CN6 Speaker CN7 Audio Jack (Line out & MIC) CN9 Inverter CN10 Build-In MIC CN12 Nurse Call Button CN14 Membrane CN15 30P All-In-One (Membrane, 2D scanner, RFID, Smart card, Audio Jack) CN17 Nurse Call LED Power CN18 Audio Jack (Line Out) CN19/JP5 System Indicator CN20 IrDA CN21 LVDS CN22 Power LED CN23 PS/2 Keyboard CN24 MSR CN25 COM1 CN26 System FAN CN27 MIC for AEC CN28 Power Button CN29/30 SATA Power CN31 HDD LED CN32/35 Internal USB CN33 USB Port For DVD Dong CN34 LAN2 LED CN36 Battery CN37 USB Port For RFID CN38 2D Scanner CN39 USB Port For Smart Card CN40 LAN1 LED DP3 DVI PWR3 +19V DC Jack RJ11_3 Handset RJ45_3 LAN2
29RJ45_4 LAN1 RJ48_3 Nurse Call SATA1/2 SATA SCSI_3 Remote Control USB3 USB3 USB4 USB1, USB2 of HUB USB5 USB1, USB2 JP3 Touch JP4 Inverter Selection JP6 LCD ID Setting JP7 MCU Power Button JP8 Power Mode Setting JP9 MCU Mode Setting JP10 System Reset JP11 CMOS Operation Mode
30 7-1-3 Jumper Setting Inverter Selection Function JP4 (1-2) (3-4) (5-6) ▲CCFL LED System Indicator Function JP5 (1-2) (3-4) (5-6) (7-8) ▲Disable Enable MCU Power Button Function JP7 (1-2) Disable ▲Enable Power Mode Setting Function JP8 (1-2) ATX Power ▲AT Power
31 MCU Mode Setting Function JP9 (1-2) ▲Normal ISP Debug System Reset Function JP10 (1-2) ▲System Normal System Reset CMOS Operation Mode Function JP11 (1-2) ▲CMOS Normal CMOS Reset ▲ = Manufacturer Default Setting Note: OPEN SHORT

Navigation menu