FLYTECH TECHNOLOGY K948C73 Bedside Terminal Hardware System User Manual R13 K948 C73 v1 0

FLYTECH TECHNOLOGY CO., LTD Bedside Terminal Hardware System R13 K948 C73 v1 0

User manual

Version 1.0 August 2013 Bedside Terminal Hardware System User Manual
i Copyright 2013 All Rights Reserved Manual Version 1.0 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without the prior written consent of the manufacturer. TRADEMARK Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation. Microsoft® and Windows® are registered trademarks of Microsoft Corporation. Other trademarks mentioned herein are the property of their respective owners. Safety IMPORTANT SAFETY INSTRUCTIONS 1. To disconnect the machine from the electrical Power Supply, turn off the power switch and remove the power cord plug from the wall socket. The wall socket must be easily accessible and in close proximity to the machine. 2. Read these instructions carefully. Save these instructions for future reference. 3. Follow all warnings and instructions marked on the product. 4. Do not use this product near water. 5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. 6. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided. 7. This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company. 8. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. 9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
ii CE MARK This device complies with the requirements of the EEC directive 2004/108/EC with regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage Directive” FCC This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation "Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment." This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help Battery Caution Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery according to the local disposal instructions. Indicating that replacement by inadequately trained personnel could result in a hazard (such as excessive temperatures, fire, or explosion) Lithium battery: CR2032
iii Safety Caution Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related legislation, peripherals shall be 4.7.3.2 "Materials for fire enclosure" compliant. 4.7.3.2 Materials for fire enclosures For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material of a FIRE ENCLOSURE, in the thinnest significant wall thickness used, shall be of V-1 CLASS MATERIAL or shall pass the test of Clause A.2. For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all STATIONARY EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest significant wall thickness used, shall be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1 CAUTION SYMBOL IN CARTON ATTENTION WARNING: To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth. WARNING: Do not modify this equipment without authorization of the manufacturer. WARNING: If an appliance coupler or separable plug is used as the disconnecting device, it shall
iv be readily identifiable and easily reached by the operator. For single-phase portable equipment, a plug on a cord of length not greater than 3m is considered to be easily reached. LEGISLATION AND WEEE SYMBOL 2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling and disposal of electric and electronic devices and their components. The crossed dustbin symbol on the device means that it should not be disposed of with other household wastes at the end of its working life. Instead, the device should be taken to the waste collection centers for activation of the treatment, collection, recycling and disposal procedure. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. Power supply is specified as a part of ME EQUIPMENT Please read the user manual
vRevision History Revision Date Description V1.0 August, 2013  Release
vi Table of Contents 1 Intended Use ...................................................... 1 2 Package Checklist ............................................ 2 2-1 Standard Items ................................................................................. 2 3 System View ....................................................... 3 3-1 Front View .......................................................................................... 3 3-2 Side View............................................................................................ 4 3-3 Rear View ........................................................................................... 4 3-4 Bottom View ...................................................................................... 5 3-5 Dimension .......................................................................................... 5 4 System Assembly .............................................. 6 4-1 SSD/HDD Replacement .................................................................. 6 5 Peripherals Installation .................................... 7 5-1 Phone module Installation .............................................................. 7 5-2 Stand Installation ………………………………………………………………….8 6 Specification ...................................................... 9 7 Jumper Setting ................................................ 12 7-1 C73 Motherboard ........................................................................... 12 7-2 Connectors & Functions ................................................................ 13 7-3 Jumper Setting ................................................................................ 14
11 Intended Use According to the Instructions for Use (IFU) of the manufacturer, the Bedside Terminal has the following intended use: The Bedside Terminal Hardware System is a computing device capable of storing, retrieving and sending data electronically. This Bedside Terminal Hardware System, including its user interface, battery, PCB and power supply, is intended to be fixed to a stand in medical care environment.
22 Package Checklist 2-1 Standard Items a. System b. Phone module c. Power adapter d. Power Cable e. Manual f. Stand
33 System View 3-1 Front View Number Description 1 Build-in camera 2 Camera LED 3 Touch screen 4 Touch keys (from left to right: reading light, volume down, volume up, channel down, channel up , power button) 5 Smart IC card reader 6 VOIP phone (optional)
43-2 Side View Number Description 1 Combo smart IC card reader with separate RFID antenna (optional) 2 Speaker 3-3 Rear View Number Description 1 Light Sensor 2 Webcam switch 3 Ventilation 4 SSD/HDD door 5 Cable cover 6 Vertical I/O port (from left to right: Nurse call, Display port, DC jack, USBx2, LAN )
53-4 Bottom View Number Description 1 Ventilation 2 From left to right: Video in, Audio left, Audio right (optional) 3 Bottom I/O port (from let to right: LAN, USBx2, Remote, Power button) 4 Microphone 5 Smart IC card reader 6 USBx1 7 Phone jack (RJ11) 8 From left to right: Audio line-out, Mic-in, Audio line-out 3-5 Dimension
64 System Assembly 4-1 SSD/HDD Replacement 1. Remove the screw (x1) to open the HDD door. 2. Remove the screw (x1) that fixed the HDD to the system. 3. Pull the HDD outward as shown in the picture. 4. The HDD is secured by a metal bracket, remove the screws (x2) to release the metal bracket from the HDD.
75 Peripherals Installation 5-1 Phone module Installation 1. Loosen the screw(x1) to open the cable cover. 2. Slide the phone module into the phone holder and connect the other end of the phone cable to the connector on the system.
85-2 Stand Installation 2. Fasten the screws.(monitor screw M6x10 4pcs)
96 Specification Model K948 Motherboard C73 Processor Intel Celeron 1047UE Core Logic CPU with Graphic built-in HM76 System Memory 2 x DDR3 SO-DIMM slot up to 8GB FSB1600Mhz Graphic Memory DX11, HD Graphic 350MHz LAN Controller / PHY Intel WG82583V / Intel WG82579V Audio Controller Realtek ALC 662-GR HD codec I/O Controller Winbond W83627UHG Touch TF P-cap 18.5” Camera LED Green-color (GPIO) Microphone 1 Power LED Tri-color (GPIO) Watch Dog Timer Hardware WDT Display Size 18.5” Resolution 1366 x 768 Brightness 250 nits DC-In 12V-48V 5A-1.5A Storage HDD Either 2.5" SATA SSD or HDD Expansion Mini PCI e 1 x full size slot or half size slot Side I/O (Back-Left) Smart IC Card Reader(optional) 1 Rear I/O (Left) LAN (2nd LAN) 1xRJ45 (with 10/100/1000,LED indicator) USB 2 (USB 2 .0) Remote 1x SCSI 26 pin Reset Button 1, button can be pressed by probe Power Button 1 Rear I/O (Right) Composite Video Video in, Audio Left, Audio Right Line-out 2 (Auto-detect,GPIO), in external IO
10Model K948 Motherboard C73 Mic-In 1 (Auto-detect,GPIO), in external IO Vertical I / O LAN 1 x RJ45 (with 10/100/1000) Power DC Jack 1 x DVI-D Display Port 1 x DVI-D USB 2 (USB 2 .0) Nurse Call 1 x RJ48 Touch Keys Power Button 1xPower button (GPIO) Channel Adjustment 1xChannel up, 1xChannel down (GPIO) Volume 1xVolume up, 1xVolume down (GPIO) Reading light 1xReading light(GPIO) Environment EMC & Safety FCC Class B, CE, LVD / UL60950 / EN60601 Environment Operating Temperature 0°C ~ 35°C (32°F ~ +95°F) Storage Temperature -20°C ~ 60°C (-4°F ~ 140°F) Humidity 20% - 85% RH non condensing Weight Weight 5Kgs Operating System OS Support Windows Embedded POSReady7, Windows 7, Linux Communication & Peripherals Speaker 2 x 2.5W Build In Microphone In the bottom side Webcam 5M web cam (USB interface) with webcam door (w/ fly LED cable to MB & control by GPIO) VOIP Phone (Front left) Handset module (optional) Smart IC Card Reader Comply with ISO 7816-1,2,3,T=1 and T=0 protocol Combo Smart IC Card Reader (optional) with separate RFID antenna in the front bezel Comply with ISO 7816-1,2,3,T=1 and T=0 Support MIFARE, MIFARE+ ,Desfire, PC/SC 2.0, HID Light Sensor Yes (GPIO) TV Tuner & DVD Maker Card Mechanical reserved * This specification is subject to change without prior notice. Application: Access to patient records / Hospital administration system / Bed management
11Manufactory information: Factory: Flytech Technology Co., Ltd. Address: NO.36 Huaya 3rd Rd., Guishan Township, Taoyuan County 33383, Taiwan Tel No: 886-3-272-9688 Fax No: 886-3-272-9666 Note: Cleaning solution-Wipe with cloth using clean water, 2 times a week. Adaptor Manufacturer: FSP TECHNOLOGY INC. 1. Model: PMP105-18-B15 Rating: 100-240V,47-63Hz,0.7 – 1.4A 2. Model: PMP60-12-B16 Rating: 100-240V,47-63Hz,1.22-0.68A
127 Jumper Setting 7-1 C73 Motherboard
13 7-2 Connectors & Functions Connector Function CN2 Scanner CN3 Nurse Call LED Power CN4 Build-In MIC CN5 Inverter CN6 COM5 (for touch) CN7 USB port for Web Cam CN8 HDD LED CN9 SATA Power CN10 SATA Power CN11 PS/2 keyboard CN12 LVDS CN14 COM1 CN16 USB CN17 Power LED CN18 USB CN19 USB CN20 IrDA CN22 Reading Light CN23 Cradle CN25 USB CN26 USB CN27 First Audio Jack CN28 Second Audio Jack CN29 To front USB board connector CN30 30P All-In-One (Membrane, 2D scanner, RFID, Smart CN31 Speaker & MIC CN32 MSR CN33 Speaker CN34 MIC CN36 Power Button CN37 LAN LED CN38 Adaptor Connector CN39 LAN LED RJ45_1 LAN1 USB1 USB1, USB2 SCSI 1 SATA SW1 System Reset SW2 System Power Button RJ45_2 LAN2 DP1 DVI-D PWR1 Adaptor Power Jack USB2 USB1, USB2 RJ48_1 Nurse Call USB3 USB RJ11_1 Handset SATA0 SATA SATA1 SATA FAN_CPU1 CPU Fan
14 7-3 Jumper Setting Brightness Type Selection Function JP1 (1-2) (3-4) (5-6) ▲LED Power Mode Setting Function JP8 (1-2) ▲ATX Power AT Power LCD ID Setting Function JP5 (1-2) (3-4) (5-6) (7-8) 18.5” AUO LCD ▲ = Manufacturer Default Setting OPEN SHORT

Navigation menu