FRC Internet ABCAU500G 2.4GHz mini PCI 802.11b/g User Manual Installation Instructions

Download:
Mirror Download [FCC.gov]
Document ID	1267393
Application ID	//3UH7dOJqL1xnWDqRvemA==
Document Description	Installation Instructions
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.79kB (22373 bits)
Date Submitted	2010-04-15 00:00:00
Date Available	2010-04-15 00:00:00
Creation Date	2010-04-05 12:56:56
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2010-04-05 12:56:56
Document Title	Microsoft Word - AB-CAU-500-GGGA installation instructions _3-30-10_.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	MBriggs

AB-CAU-500-GGGA Installation Instructions
IMPORTANT: Professional installation of this unit is required in order to comply with regulatory
requirements. Detailed software setup information is available only to properly trained
and qualified installation personnel. Contact FRC Internet Products, LLC for more
information.
Installation Instructions
The AB-CAU-500-GGGA Wireless Access Point w/Backhaul unit is designed to mount to a 1 ½”
– 1 ¾” diameter pole using the attached mounting clamp. Slide the clamp down the mounting pole (RF
connector side facing up) until the desired position is achieved, then tighten the two U-bolt nuts until the
unit is securely attached to the pole
Assemble and attach the enclosed weatherproof Ethernet connector per the included instructions
(Tyco Electronics Instruction sheet 408-8933). NOTE: Ethernet wiring to be standard wiring per
TIA/EIA-568-B
Connect the other end of the Ethernet wiring to the Ethernet POE injector. The POE injector
should be powered by the included POE power supply.
Connect RF cables and antennas. Antennas should be mounted per manufacturers instructions
included with the selected antenna. Unused RF connectors should be properly covered using a type “N”
dust cap or other suitable method. (Please note other installation notes listed below when installing
antennas).
Other important installation notes:
•
•
•
•
•
•
When using RF cables, ensure the antenna base plate or frame is on the same grounding plane as
the CAU. Failure to do so may result in electrical damage to the radios
Before connecting RF cables touch the center conductor and shield to the grounding plane. Always
connect the antenna first, ground or discharge the center conductor, then connect the CAU.
Any RF connector threaded on upside down forming a 'cup' needs to be taped. Follow the
recommended torque instructions for the RF connectors and NEVER force a connector.
Do not put the CAU where the surrounding air is stagnant. Heat pockets will form more readily
between the heat sync nodules creating an insulating affect.
When finished installing, double check all bolts for tightness.
If so desired, use the attached grounding lug to improve ground connections for the internal
Ethernet surge protector.
RF Exposure Information
The antennas used for this transmitter are 3 dBi max gain for radios #1-3 (802.11b/g) and
31.4.dBi max. gain for radio #4 (802.11a). Antennas for radios #1 -3 must be installed to provide a
separation distance of at least 20 cm from all persons while the antenna for radio #4 must provide a
distance of 330.75 cm from all persons. The radios must not be co-located or operating in
conjunction with any other antenna or transmitter.
AB-CAU-500-GGGA-INSTALL_r- (3-30-10)
PAGE 1 OF 2
Please ensure the appropriate RF exposure warnings are provided to the end user once installation
has been completed
FCC Terms Of Use
This unit contains FCC ID W93-ABCAU500AAAA and W93-ABCAU500G
This device complies with Part 15 of the FCC Rules and Regulations. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Contact Information
FRC Internet Products, LLC
1511 S. Benjamin Ave
Mason City, IA 50401 USA
Tel 641-424-0370
Fax 641-424-1945
info@frccorp.com
AB-CAU-500-GGGA-INSTALL_r- (3-30-10)
PAGE 2 OF 2

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2010:04:05 12:56:56
Modify Date                     : 2010:04:05 12:56:56
Title                           : Microsoft Word - AB-CAU-500-GGGA installation instructions _3-30-10_.doc
Creator                         : PScript5.dll Version 5.2
Author                          : MBriggs

EXIF Metadata provided by EXIF.tools