FUJIFILM Business Innovation LUFX Limited Modular Transmitter User Manual Lupin IOT

Fuji Xerox Corporation Limited Limited Modular Transmitter Lupin IOT

Contents

Users manual with statement

5About Consumables5.1 Available Consumables.................................................................... 725.2 EP Cartridge .................................................................................... 745.3 Fuser Unit ........................................................................................ 775.4 Transfer Roll Cartridge ..................................................................... 815.5 Feed Roll.......................................................................................... 85Lupin_IOT.book  Page 71  Monday, February 24, 2003  10:23 AM
725About Consumables5.1Available ConsumablesThe following consumables are available for this printer. To order these, contact our Printer Support Desk. EP cartridgeThe EP cartridge includes the toner and the photosensitive drum. If the toner in the EP cartridge is insufficient, the printout will become light and blurred. If it is time for replacement, replace with a new EP cartridge. The following types of EP cartridge are available: z6 Kpv: can print approximately 6,000 pagesz10 Kpv: can print approximately 10,000 pagesz15 Kpv: can print approximately 15,000 pagesThe possible number of pages that can be printed is based on A4 size paper with a print ratio of 5% and the default density setting using one EP cartridge. The number of pages that can be actually printed varies according to the conditions of use.Use of EP cartridges not recommended by our company may impair print quality or printer performance. Use only EP cartridges recommended by our company on this printer.“5.2 EP Cartridge” for details on how to replace the EP cartridge. Lupin_IOT.book  Page 72  Monday, February 24, 2003  10:23 AM Note: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
5.1 Available Consumables735About ConsumablesRegular replacement partsRegular replacement parts packaged together include the fuser unit, the transfer roll cartridge, and the feed roll. About 100,000 pages for a fuser unit and about 200,000 pages for a transfer roll cartridge and a feed roll can be printed. When these parts have reached this limit, replace them with new ones. The possible number of pages that can be printed is based on A4 size paper with a print ratio of 5% and the default density setting. The number of pages that can be actually printed varies according to the conditions of use.z“5.3 Fuser Unit” for details on how to replace the fuser unit. z“5.4 Transfer Roll Cartridge” for details on how to replace the transfer roll cartridge. z“5.5 Feed Roll” for details on how to replace the feed roll. Fuser unit Transfer roll cartridgeFeed rollLupin_IOT.book  Page 73  Monday, February 24, 2003  10:23 AM
745About Consumables5.2EP CartridgeThis section explains about the EP cartridge. 5.2.1 Cautions on Handling the EP CartridgeWhen handling the EP cartridge, take note of the following points:zDo not subject it to direct sunlight or strong light. zWhen installing the EP cartridge, select a location not subject to strong light and try to finish the installation within 5 minutes. zDo not touch the surface of the photosensitive drum. Do not let the EP cartridge stand or place it upside down. The drum might get damaged. zA drum shutter protects the photosensitive drum from light. Do not open the drum shutter. zAlthough the toner is not harmful to the body, wash it off immediately if your hands or clothes are stained with it. zIt is recommended to use up the EP cartridge within 1 year after opening it. 5.2.2 Replacing the EP CartridgeProcedure1Switch off the power of the printer.  Never throw an EP cartridge into an open flame. It can cause an explosion and you can get burnt.Lupin_IOT.book  Page 74  Monday, February 24, 2003  10:23 AM
5.2 EP Cartridge755About Consumables2Remove any paper in the center output tray. 3Open the top cover. Do not touch any parts inside the printer. 4Hold the EP cartridge by the grip and pull it out slowly. To prevent the toner from dirtying the floor, lay a piece of paper on the floor first before putting the EP cartridge down. 5Take the new EP cartridge out of the box and shake it 7 to 8 times in the manner as shown in the diagram.    zIf the toner is not evenly spread out, the print quality may drop. Also, if you did not shake the EP cartridge well, there may be operating noise or the interior of the EP cartridge may be damaged during operation. zDo not touch the surface of the photosensitive drum. Lupin_IOT.book  Page 75  Monday, February 24, 2003  10:23 AM
5.2 EP Cartridge765About Consumables6Place the EP cartridge on a flat surface and pull out the seal horizontally. zWhen pulling out the seal, pull it out horizontally. The tape might break if it is pulled out diagonally. zAfter the seal has been pulled out, do not shake or dump the EP cartridge.  7Hold the EP cartridge by the grip and insert it into the slot inside the printer. zDo not touch any parts inside the printer. zEnsure that the EP cartridge is firmly set. 8Close the top cover securely. Lupin_IOT.book  Page 76  Monday, February 24, 2003  10:23 AM
775About Consumables5.3Fuser UnitThis section explains about the fuser unit. 5.3.1 Caution on Handling the Fuser UnitThe fuser unit is included as one of the regular replacement parts. Before replacing the fuser unit, open the box of the regular replacement parts and get the new fuser unit ready. When handling the fuser unit, take note of the following points:zDo not replace the fuser unit immediately after using the printer. You may get burnt. zNever touch a labeled area found on or near the heat roller. You can get burnt. If a sheet of paper is wrapped around the heat roller, do not try to remove it by yourself to avoid injuries or burns. Switch off the machine immediately, and contact our Printer Support Desk.zBe sure to switch off and unplug the machine before accessing the interior of the machine for cleaning, maintenance, or fault clearance.  Access to a live machine’s interior can cause electric shock.Lupin_IOT.book  Page 77  Monday, February 24, 2003  10:23 AM
5.3 Fuser Unit785About Consumables5.3.2 Replacing the Fuser UnitProcedure1Switch off the power of the printer and leave it for 30 minutes until the fuser unit cools down.  2Remove any paper in the center output tray. 3Lift the second lever from the top left corner of the back of the printer. Lupin_IOT.book  Page 78  Monday, February 24, 2003  10:23 AM
5.3 Fuser Unit795About Consumables4Open the rear cover. Do not touch any parts inside the printer. 5Lift the lever at both ends of the fuser unit to unlock it. 6Pull down the 2 levers at the bottom of the fuser unit. 7Remove the fuser unit slowly. Lupin_IOT.book  Page 79  Monday, February 24, 2003  10:23 AM
5.3 Fuser Unit805About Consumables8Set the new fuser unit slowly. 9Lift up the 2 levers at the bottom of the fuser unit and push down the levers at both ends of the fuser unit to lock it.  10Close the rear cover. Lupin_IOT.book  Page 80  Monday, February 24, 2003  10:23 AM
815About Consumables5.4Transfer Roll CartridgeThis section explains about the transfer roll cartridge. 5.4.1 Caution on Handling the Transfer Roll CartridgeThe transfer roll cartridge is included as one of the regular replacement parts. Before replacing the transfer roll cartridge, open the box of the regular replacement parts and get the new transfer roll cartridge ready. When handling the transfer roll cartridge, take note of the following points:zDo not remove and reinsert the transfer roll cartridge in use. zWhen the message to replace the transfer roll cartridge appears, replace the transfer roll cartridge immediately. Otherwise, the printer will be forcibly stopped. Never throw an transfer roll cartridge into an open flame. It can cause an explosion and you can get burnt.Lupin_IOT.book  Page 81  Monday, February 24, 2003  10:23 AM
5.4 Transfer Roll Cartridge825About Consumables5.4.2 Replacing the Transfer Roll CartridgeProcedure1Switch off the power of the printer.  2Remove any paper in the center output tray. 3Open the top cover. Do not touch any parts inside the printer. Lupin_IOT.book  Page 82  Monday, February 24, 2003  10:23 AM
5.4 Transfer Roll Cartridge835About Consumables4Hold the EP cartridge by the grip to pull it out slowly. To prevent the toner from dirtying the floor, lay a piece of paper on the floor before putting the EP cartridge down. 5Squeeze the levers on both ends of the transfer roll cartridge and pull it out slowly towards you. 6Pick up  the new transfer roll cartridge by the levers at both ends and slowly slot it in. Lupin_IOT.book  Page 83  Monday, February 24, 2003  10:23 AM
5.4 Transfer Roll Cartridge845About Consumables7Hold the EP cartridge by the grip and insert it into the slot inside the printer. zDo not touch any parts inside the printer. zEnsure that the EP cartridge is firmly set. 8Close the top cover securely. Lupin_IOT.book  Page 84  Monday, February 24, 2003  10:23 AM
855About Consumables5.5Feed RollThis section explains about the feed roll. 5.5.1 Caution on Handling the Feed RollThe feed roll is included as one of the regular replacement parts. Before replacing the feed roll, open the box of the regular replacement parts and get the new feed roll ready. When handling the feed roll, take note of the following points:There are feed rolls inside the interior of the printer (2 in 2 locations, 4 in total), tray module (1 location), paper tray (1 location), single-sheet bypass tray (1 location) and multiple-sheet bypass tray (1 location). Be sure to switch off and unplug the machine before accessing the interior of the machine for cleaning, maintenance, or fault clearance.  Access to a live machine’s interior can cause electric shock.Lupin_IOT.book  Page 85  Monday, February 24, 2003  10:23 AM
5.5 Feed Roll865About Consumables5.5.2 Replacing the Feed RollThe following procedure explains how to replace the feed roll of the paper tray. Follow the procedure here for replacing the feed roll of the tray module as well. Inside the printer (2 locations)Single-sheet bypass tray (1 location) Multiple-sheet bypass tray (1 location)Feed rollTray module (1 location) Paper tray (1 location)Lupin_IOT.book  Page 86  Monday, February 24, 2003  10:23 AM
5.5 Feed Roll875About ConsumablesFeed roll at the paper trayProcedure1Pull the paper tray out of the printer.  The feed roll on tray modules can be replaced without pulling out the paper tray. 2While pushing down the shaft of the feed roll as shown in the diagram (1), widen the tab of the feed roll to loosen it (2) and then slowly remove the feed roll from the shaft on the paper tray (3).  3Hold the tab on the new feed roll as shown in the diagram and slowly push it into the shaft on the paper tray.  Ta bLupin_IOT.book  Page 87  Monday, February 24, 2003  10:23 AM
5.5 Feed Roll885About ConsumablesBy aligning the small tabs on the feed roll with the slots of the shaft, push the feed roll completely in so that the tab fits into the slot. 4Push the paper tray completely into the printer. Feed roll inside the printerProcedure1Remove any paper in the center output tray. Lupin_IOT.book  Page 88  Monday, February 24, 2003  10:23 AM
5.5 Feed Roll895About Consumables2Open the top cover. Do not touch any parts inside the printer. 3Hold the EP cartridge by the grip and pull it out slowly. To prevent the toner from dirtying the floor, lay a piece of paper on the floor first before putting the EP cartridge down. 4While pushing down the shaft of the feed roll as shown in the diagram, widen the tab on the feed roll to loosen it (1) and then slowly remove the feed roll from the shaft of the paper tray (2).  5Hold the tab on the new feed roll as shown in the diagram and slowly push it into the shaft on the paper tray.  Ta bLupin_IOT.book  Page 89  Monday, February 24, 2003  10:23 AM
5.5 Feed Roll905About ConsumablesBy aligning the small tabs on the feed roll with the slots of the shaft, push the feed roll completely in so that the tab fits into the slot. 6Hold the EP cartridge by the grip and insert it into the slot inside the printer. zDo not touch any parts inside the printer. zEnsure that the EP cartridge is firmly set. 7Close the top cover securely. Lupin_IOT.book  Page 90  Monday, February 24, 2003  10:23 AM
1.4 Installation Procedure10Installing the Printer11.4.3 Installing the EP CartridgeWhen installing the EP cartridge, take note of the following points:zDo not subject it to direct sunlight or strong light. zWhen installing the EP cartridge, select a location not subject to strong light and try to finish the installation within 5 minutes. zDo not touch the surface of the photosensitive drum. Do not stand or place the EP cartridge upside down. The drum might get damaged. zA drum shutter protects the photosensitive drum from light. Do not open the drum shutter. zAlthough the toner is not harmful to the body, wash it off immediately if your hands or clothes are stained with it. zIt is recommended to use up the EP cartridge within 1 year after opening it. Procedure“5.2.2 Replacing the EP Cartridge” for details when replacing the EP cartridge.1Open the top cover. Do not touch any parts inside the printer. Never throw an EP cartridge into an open flame. It can cause an explosion and you can get burnt.Lupin_IOT.book  Page 10  Monday, February 24, 2003  10:23 AM
1.4 Installation Procedure11Installing the Printer12Take the EP cartridge out of the box and shake it 7 to 8 times as shown in the diagram.    3Place the EP cartridge on a flat surface and pull the seal out horizontally. zWhen pulling out the seal, pull it out horizontally. The tape might break if it is pulled out diagonally. zAfter the seal has been pulled out, do not shake or bump the EP cartridge.  4Hold the EP cartridge by the grip and insert it into the slot inside the printer. zDo not touch any parts inside the printer. zEnsure that the EP cartridge is firmly set. 5Close the top cover securely. Lupin_IOT.book  Page 11  Monday, February 24, 2003  10:23 AM

Navigation menu