FXT Technology 002 5.8G AV Transmitter User Manual FX799T 25MW FXT Technology Co Ltd

FXT Technology Co., Limited 5.8G AV Transmitter FX799T 25MW FXT Technology Co Ltd

User manual

PRODUCT SPECIFICATION MODEL: FX799T FXT 5.8GHz 25mw 40 Channel AV Transmitter Modulate Wideband FM Modulate Video Format NTSC/PAL Characteristics Value Units Min. Typ. Max. 1 Output Impedance --- 50 --- Ohm 2 Output Power --- 13 --- dBm 3 Frequency Range 5645-5945 MHz 4 Operating Voltage 7.0 12 20 V 5 Supply current --- 60 --- mA 6 Output Voltage(VOUT) VOUT = 5V V 7 Operating Temperature -10 --- +85 ℃ 8 Video Band Width --- 6.0 --- MHz 9 Audio Carrier Frequency --- 6.5 --- MHz 10 Video Input Level 0.8 1.0 1.2 Vp-p 11 Video Input Impedance --- 75 --- Ohm 12 Audio Input Level 0.5 --- 2.0 Vp-p 13 Audio Input Impedance --- 10K --- Ohm 14 Weight ---- 7.5 --- Gram(s) 15 Antenna Connector SMA Connector 16 Dimensions (L x W x H) 31x22x10 mm 利用 pdfFactory Pro 测试版本创建的PDF文档 www.pdffactory.com
Change frequency band & channel Single push to change CH, push and hold for 2 seconds to change FR Below is TX channel table for your reference: CH FR CH CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 FR FR1(F) 5740 5760 5780 5800 5820 5840 5860 5880 FR2(E) 5705 5685 5665 5645 5885 5905 5925 5945 FR3(A) 5865 5845 5825 5805 5785 5765 5745 5725 FR4(R) 5658 5695 5732 5769 5806 5843 5880 5917 FR5(B) 5733 5752 5771 5790 5809 5828 5847 5866 Pin description 5PIN connector 1. DC IN (7-20V) 2. GND 3. VIDEO IN 4. GND 5. 5V/VCC OUT 利用 pdfFactory Pro 测试版本创建的PDF文档 www.pdffactory.com
The output power of this device is less than 20mW.The SAR test is not required. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user’s authority to operate the equipment. A certified modular has the option to use a permanently affixed label, or an electronic label. For a permanently affixed label, the module must be labelled with an FCC ID: 2AGB8-002. The OEM manual must provide clear instructions explaining to the OEM the labelling requirements, options and OEM user manual instructions that are required For a host using a this FCC certified modular with a standard fixed label, if (1) the module’s FCC ID is notvisible when installed in the host, or (2) if the host is marketed so that end users do not have straightforward commonly used methods for access to remove the module so that the FCC ID of the module is visible; then an additional permanent label referring to the enclosed module: “Contains Transmitter Module FCC ID: 2AGB8-002 or “Contains FCC ID: 2AGB8-002 ” must be used. The host OEM user manual must also contain clear instructions on how end users can find and/or access the module and the FCC ID. Host product is required to comply with all applicable FCC equipment authorizations regulations, requirements and equipment functions not associated with the transmitter module portion. compliance must be demonstrated to regulations for other transmitter components within the host product; to requirements for unintentional radiators (Part 15B). To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. If a host was previously authorized as an unintentional radiator under the Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements. Since this may depend on the details of how the module is integrated with the host, we suggest the host device to recertify part 15B to ensure complete compliance with FCC requirement: Part 2 Subpart J Equipment Authorization Procedures , KDB784748 D01 v07, and KDB 997198 about importation of radio frequency devices into the United States.

Navigation menu