FXT Technology 002 5.8G AV Transmitter User Manual FX799T 25MW FXT Technology Co Ltd

Download:
Mirror Download [FCC.gov]
Document ID	2848418
Application ID	I6+1CHVt+Qp93Fz6Zpt9mA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.86kB (110737 bits)
Date Submitted	2015-12-21 00:00:00
Date Available	2015-12-21 00:00:00
Creation Date	2015-12-10 15:21:30
Producing Software	Adobe Acrobat Pro 9.3.2
Document Lastmod	2015-12-10 15:21:30
Document Title	FX799T 25MW --FXT Technology Co.,Ltd
Document Creator	Adobe Acrobat Pro 9.3.2
Document Author:	Administrator

PRODUCT
SPECIFICATION
MODEL: FX799T
FXT 5.8GHz 25mw 40 Channel
AV Transmitter
Modulate
Wideband FM Modulate
Video Format
NTSC/PAL
Value
Units
Characteristics
Min.
Typ.
Max.
Output Impedance
---
50
---
Ohm
Output Power
---
13
---
dBm
Frequency Range
Operating Voltage
Supply current
Output Voltage(VOUT)
Operating Temperature
-10
---
+85
℃
Video Band Width
---
6.0
---
MHz
Audio Carrier Frequency
---
6.5
---
MHz
10
Video Input Level
0.8
1.0
1.2
Vp-p
11
Video Input Impedance
---
75
---
Ohm
12
Audio Input Level
0.5
---
2.0
Vp-p
13
Audio Input Impedance
---
10K
---
14
Weight
----
7.5
---
15
Antenna Connector
16
Dimensions (L x W x H)
5645-5945
MHz
7.0
12
20
---
60
---
mA
VOUT = 5V
SMA Connector
31x22x10 mm
利用 pdfFactory Pro 测试版本创建的PDF文档 www.pdffactory.com
Ohm
Gram(s)
Change frequency band & channel
Single push to change CH, push and hold for 2 seconds to change FR
Below is TX channel table for your reference:
CH
FR
CH
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
FR1(F)
5740
5760
5780
5800
5820
5840
5860
5880
FR2(E)
5705
5685
5665
5645
5885
5905
5925
5945
FR FR3(A)
FR4(R)
5865
5658
5845
5695
5825
5732
5805
5769
5785
5806
5765
5843
5745
5880
5725
5917
FR5(B)
5733
5752
5771
5790
5809
5828
5847
5866
Pin description
5PIN connector
1. DC IN (7-20V)
2. GND
3. VIDEO IN
4. GND
5. 5V/VCC OUT
利用 pdfFactory Pro 测试版本创建的PDF文档 www.pdffactory.com
The output power of this device is less than 20mW.The SAR test is not required.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications or changes to this equipment. Such modifications or changes
could void the user’s authority to operate the equipment.
A certified modular has the option to use a permanently affixed label, or an electronic label.
For a permanently affixed label, the module must be labelled with an FCC ID: 2AGB8-002.
The OEM manual must provide clear instructions explaining to the OEM the labelling
requirements, options and OEM user manual instructions that are required
For a host using a this FCC certified modular with a standard fixed label, if (1) the module’s
FCC ID is notvisible when installed in the host, or (2) if the host is marketed so that end
users do not have straightforward commonly used methods for access to remove the module
so that the FCC ID of the module is visible; then an additional permanent label referring to
the enclosed module:
“Contains Transmitter Module FCC ID: 2AGB8-002 or “Contains FCC ID: 2AGB8-002 ”
must be used. The host OEM user manual must also contain clear instructions on how end
users can find and/or access the module and the FCC ID.
Host product is required to comply with all applicable FCC equipment authorizations
regulations, requirements and equipment functions not associated with the transmitter
module portion. compliance must be demonstrated to regulations for other transmitter
components within the host product; to requirements for unintentional radiators (Part 15B).
To ensure compliance with all non-transmitter functions the host manufacturer is
responsible for ensuring compliance with the module(s) installed and fully operational. If a
host was previously authorized as an unintentional radiator under the Declaration of
Conformity procedure without a transmitter certified module and a module is added, the
host manufacturer is responsible for ensuring that the after the module is installed and
operational the host continues to be compliant with the Part 15B unintentional radiator
requirements. Since this may depend on the details of how the module is integrated with
the host, we suggest the host device to recertify part 15B to ensure complete compliance with
FCC requirement: Part 2 Subpart J Equipment Authorization Procedures , KDB784748 D01
v07, and KDB 997198 about importation of radio frequency devices into the United States.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Administrator
Create Date                     : 2015:12:10 15:21:30+08:00
Modify Date                     : 2015:12:10 15:21:30+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2015:12:10 15:21:30+08:00
Creator Tool                    : Adobe Acrobat Pro 9.3.2
Format                          : application/pdf
Title                           : FX799T 25MW --FXT Technology Co.,Ltd
Creator                         : Administrator
Document ID                     : uuid:42bf8b39-57f3-4ff5-8f59-99f0953d78bf
Instance ID                     : uuid:5c0fd880-66de-4815-abd2-7a40f3052ab8
Producer                        : Adobe Acrobat Pro 9.3.2
Page Count                      : 3

EXIF Metadata provided by EXIF.tools