Fanstel Taipei BC840M Bluetooth 5.0 Module User Manual
Fanstel Corporation, Taipei Bluetooth 5.0 Module
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 4193135 |
| Application ID | NEDuxCJNhxpSATUr88465A== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 38.94kB (486767 bits) |
| Date Submitted | 2019-03-07 00:00:00 |
| Date Available | 2019-03-11 00:00:00 |
| Creation Date | 2019-03-07 09:34:07 |
| Producing Software | Acrobat Distiller 10.1.16 (Windows) |
| Document Lastmod | 2019-03-07 09:34:07 |
| Document Title | untitled |
BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 BluNor BC840 is a powerful, highly flexible, ultra low power Bluetooth Low Energy (BLE) using Nordic nRF52840 SoC. With an ARMCortexTM M4F MCU, available 1MB flash, 256KB RAM, embedded 2.4GHz multiprotocol transceiver, and an integrated PCB trace antenna. It allows faster time to market with reduced development cost. BC840 size is compact(7.0x9.0x1.5mm), short range (10 meters) module. It is ideal for wearable. BC832M is compact in size. It range is estimated at 1000 meters for 125 Kbps data rate. Specifications: nRF52840 CKAA, ARM Cortex M4F, 64 MHz 64 level comparator ARM® TrustZone® Cryptocell-310 co- 15 level comparator with wake-up from OFF processor mode Complete RF solution with integrated antenna Temperature sensor BLE 5 data rate: 2Mbps, 1Mbps, 500kbps, 4x4-channel pulse width modulator (PWM) 125kbps. Audio peripherals: I2S, digital microphone IEEE 802.15.4 Thread and Zigbee data rate: 250 interface (PDM) Kbps 5 x 32 bit timers with counter mode 2.4 GHz proprietary data rate: 2 Mbps, 1 Mbps Up to 4x SPI masters/3x SPI slaves DC-DC converter, inductors on board. Up to 2x I2C compatible 2-wire masters/slaves Direct powered by Lithium batteries or USB 2x UART (CTS/RTS) supply (up to 5.5V) Quadrature Demodulator (QDEC) 32 MHz main crystal on board. 3x real time counters (RTC) Serial Wire Debug (SWD) 128-bit AES HW encryption Nordic SoftDevice Ready SoC Receiver Sensitivity: -96 dBm at 1Mbps Over-the-Air (OTA) firmware update SoC TX power: programmable +8dBm to - Flash/RAM: 1MB/256KB. 20dBm. 48 General purpose I/O pins LGA, 64 pins. USB 2.0 full speed (12 Mbps) controller Integrated PCB trace antenna QSPI 32 MHz interface Operation voltage: 1.7V to 5.5V High speed 32 MHz SPI Operation temperature: - 4 0 ° C t o + 8 5 ° C Type 2 NFC-A tag with wake-on field, Touch- QDID: 108621 to-pair support FCC ID: Pending Programmable peripheral interconnect (PPI) IC IC Pending 12 bit/200 Ksps ADC, 8 configurable channels CE, TELEC, RCM: Pending with programmable gain Applications Wearable Beacons/Proximity Secure IoT Connected appliances BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 Lighting products Home and building automation Sensors Model Summaries module SoC Size, mm BT Antenna BC840 nRF52840-CKAA 7.0x9.0x1.5 PCB trace BC840M nRF52840-CKAA 7.0 (10 antenna area)x12.0x1.5 PCB trace BT range,1 Mbps, LMPI 10 meters, est. 150 meters.est BC840E nRF52840-CKAA 7.0x12.0x1.5 u.FL BT range, 1Mbps, 1.52m BT range, 125 Kbps, LMPI. 400 meters, est. BT range, 125 kBps, 1.52m Availability Sample Sample Sample BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 Table Of Contents 1. Introduction .......................................................................................................................................................... 4 BC840 Block Diagram.......................................................................................................................................... 4 BC840 .................................................................................................................................................................. 5 BC840M ............................................................................................................................................................... 5 BC840E ................................................................................................................................................................ 5 2. Codes Development Using Nordic Tools ............................................................................................................ 5 Easy, fast and safe code development ............................................................................................................... 5 Over-The-Air DFU ................................................................................................................................................ 5 SoftDevices .......................................................................................................................................................... 5 Development Tools .............................................................................................................................................. 6 3. Product Descriptions ............................................................................................................................................ 7 Block Diagram of nRF52840................................................................................................................................ 7 ARM Trustzone CryptoCell 310 ........................................................................................................................... 9 Mechanical Drawings ......................................................................................................................................... 12 Pin Assignments of BC840, BC840M, and BC840E ......................................................................................... 14 Pin Function ....................................................................................................................................................... 16 Mounting BC840 and BC840M on the Host PCB .............................................................................................. 17 Host Board Layout ............................................................................................................................................. 17 4. BC840 Evaluation Board ...................................................................................................................................18 Nordic Development Tools ............................................................................................................................... 18 Android OS Apps .............................................................................................................................................. 19 iOS Apps ........................................................................................................................................................... 19 BC840 EvaluationBoard Schematics................................................................................................................. 20 Suggestion for Battery Power Application ......................................................................................................... 21 5. Production ..........................................................................................................................................................22 Preloaded Firmware ........................................................................................................................................... 22 AT Command Codes ......................................................................................................................................... 22 Soldering Temperature-Time Profile for Re-Flow Soldering ............................................................................. 23 Cautions, Design Notes, and Installation Notes ................................................................................................ 23 Packaging........................................................................................................................................................... 26 FCC Label .......................................................................................................................................................... 26 Revision History .....................................................................................................................................................27 6. Contact Us ......................................................................................................................... 錯誤! 尚未定義書籤。 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 1. Introduction BluNor BC840 Series are powerful, highly flexible, ultra low power wireless modules using Nordic nRF52840 SoCs. With an ARMCortexTM M4F MCU, 1MB flash, 256KB RAM, embedded 2.4GHz multi-protocol transceiver, and an integrated antenna, it allows faster time to market with reduced development cost. The following is a block diagram of BC840. Antenna circuit and main clock are integrated. All 48 GPIOs of nRF52840 can be accessed from main board. For lower power consumption at idle state, a 32.768 kHz crystal can be added on the host board. Connection to an external NFC (Near Field Communication) antenna is provided. BC840 Block Diagram BlueNor BC840M is a sister module of BC840. The physical size is slightly larger to accommodate longer range PCB trace antenna. BC840E is with an u.FL connector for an external antenna. BC840 and BC840M common features: • nRF52840 CKAA with Cortex M4F MCU • 1MB flash, 256 KB RAM • Supports NFC • Integrated PCB trace antenna. BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 • 64 LGA pins • 48 GPIOs BC840 • Estimated range is 10 meters. • Size: 7.0x9.0x1.5 mm. BC840M • Estimated range is 1000 meters. • Size: 7.0x12.0x1.5mm.Antenna area width is 10.0mm. BC840E • With an u.FL connector for external antenna. • Size: 7.0x12.0x1.5 mm. 2. Codes Development Using Nordic Tools Development tools by Nordic and other third party development tools recommended by Nordic should be used . Easy, fast and safe code development Nordic development environment for nRF52840 offers a clean separation between application code development and embedded protocol stacks. This means compile, link and run time dependencies with the embedded stack and associated debugging challenges are removed. The Bluetooth low energy and ANT stack is a pre-compiled binary, leaving application code to be compiled stand-alone. The embedded stack interface uses an asynchronous and event driven model removing the need for RTOS frameworks. Over-The-Air DFU The nRF52840 is supported by an Over-The-Air Device Firmware Upgrade (OTA DFU) feature. This allows for in the field updates of application software and SoftDevice. SoftDevices The Nordic protocol stacks are known as SoftDevices and complement the nRF52 Series SoCs. All nRF52 Series are programmable with software stacks from Nordic. This bring maximum flexibility to application development and allows the latest stack version to be programmed into the SoC. SoftDevices available from Nordic: S140: Bluetooth low energy concurrent central/peripheral/observer/broadcaster stack. BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 Development Tools Nordic Semiconductor provides a complete range of hardware and software development tools for the nRF52 Series devices. nRF52 DK board is recommended for firmware development. Nordic software development tools can be downloaded from the following webpage. http://infocenter.nordicsemi.com/index.jsp?topic=/com.nordic.infocenter.nrf52/dita/nrf52/development/nrf5 2_dev_kit.html&cp=1_1 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 3. Product Descriptions Brief description of nRF52840 SoC is provided. For full description of the SoC, please download from Nordic Semiconductor website. https://www.nordicsemi.com/eng/Products/Bluetooth-low-energy Block Diagram of nRF52840 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 The following is a block diagram of Nordic nRF52840 Bluetooth Low Energy (BLE) SoC. Arrows with white heads indicate signals that share physical pins with other signals. The 32 bit ARM Cortex M4F MCU with hardware supports for DSP instructions and floating point operations, code density and execution speed are higher than other Cortex M MCU. The Programmable Peripheral Interconnect (PPI) system provides a 20-channel bus for direct and autonomous system peripheral communication without CPU intervention. This brings predictable latency times for peripheral to peripheral interaction and power saving benefits associated with leaving CPU idle. The device has 2 global power modes BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 ON/OFF, but all system blocks and peripherals have individual power management control which allows for an automatic switching RUN/IDLE for system blocks based only on those required/not required to achieve particular tasks. The radio supports Bluetooth low energy and ANT. Output power is scalable from a maximum of +8dBm down to -20 dBm in 4dB steps. Sensitivity is increased to -96 dBm to -89 dBm, depending on data rate. Sensitivity for BLE is -96 dBm, and -92.5 dBm for ANT. The NFC block supports NFC-A tags with proximity detection and Wake-on-field from low power mode. The NFC enables Out-Of-Band (OOB) Bluetooth pairing of devices and thus greatly simplifying deployment. ARM Trustzone CryptoCell 310 ARM® TrustZone® CryptoCell-310co-processor is a security subsystem which provides Root of Trust (RoT) and cryptographic services for a device. CryptoCell services are available to the application through a software library API, not a hardware register interface. The following cryptographic features are provided. • FIPS-140-2 certified True Random Number Generator (TRNG) BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 • RSA asymmetric encryption Up to 2048 bit key size PKCS#1 v2.1/v1.5 Optional CRT support • Elliptic curve cryptography (ECC) NIST FIPS 186-4 recommended curves using pseudo-random parameters, up to 521 bits: ➢ Prime field: P-192, P-224, P-256, P-384, P-521 SEC 2 recommended curves using pseudo-random parameters, up to 521 bits: ➢ Prime field: P-160, P-192, P-224, P-256, P-384, P-521 Koblitz curves using fixed parameters, up to 256 bits: ➢ Prime field: P-160, P-192, P-224, P-256 Edwards/Montgomery curves: ➢ Ed25519, Curve 25519 ECDH/ECDSA support • Secure remote password protocol (SRP) Up to 3072 bit operations • Hashing functions SHA-1, SHA-2 up to 256 bit size keyed-hash message authentication code (HMAC) • AES symmetric encryption General purpose AES engine (encrypt/decrypt, sign/verify) 128 bit key size Supported encryption modes: ECB, CBC, CMAC/CBC-MAC, CTR, CCM/CCM*. • ChaCha20/Poly1305 symmetric encryption Supported keyed size: 128 and 256 bits Authenticated encryption with associated data (AEAD) mode 10 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 11 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 Mechanical Drawings The followings are mechanical drawings of BC840. Size is 7.0x9.0mm. It has 64 LGA pins on a 8x8 matrix, top view of module: 12 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 BC840M mechanical drawings, top view. 13 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 Pin Assignments of BC840, BC840M, and BC840E The followings are BC840/BC840M/BC820E pin assignment. Pin functions are in a table in next section. Please refer to Nordic nRF52840 Product Specifications for detailed descriptions and features supported. https://www.nordicsemi.com/eng/Products/nRF52840 BC840, BC840M, and BC840E pin assignments BC840 52840 CKAA pin# pin# pin name Descriptions A0 J1 P1.01 GPIO A1 K2 P0.25 GPIO A2 K4 P0.19 GPIO A3 J6 P0.17 GPIO A4 K8 D+ USB D+ A5 J8 D- USB D- A6 H9 DCCH DC to DC converter output A7 J10 VDDH High Voltage Power Supply B0 H1 P1.04 GPIO B1 J2 SWDIO Serial Wire Debug Data I/O B2 K3 P0.22 GPIO 14 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 B3 K7 P0.15 GPIO B4 K6 P0.18 GPIO P0.18/reset B5 J9 VBUS 5V DC power for USB 3.3V regulator B6 F9 P0.07 GPIO B7 G10 P0.12 GPIO C0 G1 P1.07 GPIO C1 H2 SWDCLK Serial Wire Debug clock input C2 J5 P0.20 GPIO C3 J4 P0.21 GPIO C4 J7 P0.14 GPIO C5 G9 P1.08 GPIO C6 F10 P1.09 GPIO C7 E10 P0.08 GPIO D0 J3 P1.00 GPIO D1 G2 P1.05 GPIO D2 F1 P0.09 GPIO, NFC antenna connection D3 H6 P0.16 GPIO D4 H7 P0.13 GPIO D5 H8 P0.11 GPIO D6 D9 P0.27 GPIO, configured as I2C SCL on EV-BC840 D7 E9 P0.06 GPIO E0 F3 P1.03 GPIO E1 E3 P1.06 GPIO E2 E2 P0.10 GPIO, NFC antenna connection E3 C6 P1.15 GPIO E4 C7 P0.29/AIN5 GPIO, analog input 5 E5 C8 P0.31/AIN6 GPIO, analog input 6 E6 C9 P0.26/SDA GPIO, configured as I2C SDA on EV-BC840 E7 C10 P0.04/AIN2 GPIO, analog input 2 F0 H5 P0.23 GPIO F1 H4 P0.24 GPIO F2 G3 P1.02 GPIO F3 C5 P1.12 GPIO F4 B6 P0.02/AIN0 GPIO, analog input 0 F5 B8 VDD DC supply in, 1.7 to 3.6V F6 B9 P0.00/XL1 GPIO, connection for 32.768 kHz sleep crystal F7 B10 P0.01/XL2 GPIO, connection for 32.768 kHz sleep crystal G0 B7 GND Ground G1 A7 P0.30/AIN7 GPIO, analog input 7 G2 A3 P1.11 GPIO 15 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 G3 A4 P1.13 GPIO G4 GND Ground G5 GND Ground G6 GND Ground G7 D10 P0.05/AIN3 GPIO, analog input 3 H0 A5 P0.03/AIN1 GPIO, analog input 1 H1 A6 P0.28/AIN4 GPIO, analog input 4 H2 B4 P1.10 GPIO H3 B5 P1.14 GPIO H4 GND Ground F5 GND Ground H6 GND Ground H7 GND Ground Pin Function 16 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 Mounting BC840 and BC840M on the Host PCB The following figure shows recommended mounting of BC840 and BC840M module on the host PCB. • For the best Bluetooth range performance, the antenna area of BC840M module shall extend 5.5 mm outside the edge of host PCB board, or 5.5 mm outside the edge of a ground plane. • For the best Bluetooth range performance, the antenna area of BC840 module shall extend 2.5 mm outside the edge of host PCB board, or 2.5 mm outside the edge of a ground plane. • The next choice is to place BC840M on a corner of host PCB, the antenna area shall extend 5.5 mm from the edge of ground plane. Ground plane shall be at least 5 mm from the edge of the antenna area of module. • The next choice is to place BC840 on a corner of host PCB, the antenna area shall extend 2.5 mm from the edge of ground plane. Ground plane shall be at least 5 mm from the edge of the antenna area of module. • We don’t recommend mounting BC840 module in the middle of a host PCB. For the best Bluetooth range performance, keep all external metal at least 30mm from the antenna area. Host Board Layout Library components for some PCB layout software are available. Or, it can be extracted from EV-BC840 evaluation board Gerber files. Gerber files can be downloaded from: http://www.fanstel.com/download-document/. 17 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 4. BC840 Evaluation Board An evaluation board consists of the followings: • Mini USB cable • Evaluation board • 10-conductor cable for connection to Nordic nRF52 DK (DK is not included) Nordic Development Tools A Nordic nRF52840 DK is recommended for programming this evaluation board. Nordic development tools can be downloaded from: https://www.nordicsemi.com/eng/Products/nRF52840 Many application examples can be downloaded from Nordic website. 18 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 Some firmware, Android OS, and iOS app codes can be downloaded from Bluetooth 5 Codes section of this Fanstel webpage. http://www.fanstel.com/download-document/ BT840 firmware can be used in all nRF52840 modules, e.g., BT840, BT840F, BT840E, BC840, and BC840M. Android OS Apps The following Android OS apps are available for download from Google Play Store: BlueNor nrf5x: to use with Bluetooth 5 stacks, AT commands, or Slave firmware. Master firmware does not connect to a smartphone. Source codes can be downloaded from http://www.fanstel.com/download-document/ BlueNor Mesh: to use with BlueNor mesh firmware to send command to any node in a mesh. Node number is displayed when acknowledgement is received. Source codes will be uploaded to Fanstel website when supporting Bluetooth 5. iOS Apps The following iOS apps can be downloaded from Apple APP Store. BlueNor Mesh: to use with BlueNor mesh firmware to send command to any node in a mesh. Node number is displayed when acknowledgement is received. BlueNor nrf5x firmware, apps, and source codes will be uploaded when ready. 19 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 BC840 EvaluationBoard Schematics 20 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 Evaluation board can be used as a reference design for using modules.. Suggestion for Battery Power Application Standby current consumption is important for battery-powered product. We suggest adding a 32.768 kHz crystal and 2 capacitors on host board. The 32MHz main clock won’t be active at idle state to save power. Two inductors required for on-board DC to DC converter are inside BC840 and BC840M. You can enable DCDC converter to have lower power consumption. 21 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 5. Production Preloaded Firmware Production testing codes are not erased before shipping from factory. To load your firmware, please erase the entire chip and re-program using instruction below. //program BT840 Bootloader+Softdevice+Application hex nrfjprog -f NRF52 --program BT840_AT_3in1PC181113.hex --chiperase --reset //The file BT840_AT_3in1PC181113.hex = softdevice S140v6.1.1+BT840_AT_UARTwithout32K+bootloader AT Command Codes Begin in November 2018, we use AT command codes for production testing. Up to date codes can be downloaded from: https://www.fanstel.com/download-document/ You can erase and reprogram with your codes. Or, use AT command codes as preloaded. If you need a special version of codes, programming services are available with MOQ and programming charges. 22 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 Soldering Temperature-Time Profile for Re-Flow Soldering Maximum number of cycles for re-flow is 2. No opposite side re-flow is allowed due to module weight. Cautions, Design Notes, and Installation Notes Failure to follow the guidelines set forth in this document may result in degrading of the product’sfunctions and damage to the product. Design Notes (1) Follow the conditions written in this specification, especially the control signals of this module. (2) The supply voltage has to be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, provide a decoupling circuit (for example a ferrite in series connection and a bypass capacitor to ground of at least 47uF directly at the module). (3) This product should not be mechanically stressed when installed. (4) Keep this product away from heat. Heat is the major cause of decreasing the life of these products. (5) Avoid assembly and use of the target equipment in conditions where the products' temperature may exceed the maximum tolerance. (6) The supply voltage should not be exceedingly high or reversed. It should not carry noise and/or spikes. (7) this product away from other high frequency circuits. Notes on Antenna and PCB Layout (1) Don’t use a module with internal antenna inside a metal case. 23 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 (2) For PCB layout: • • • Avoid running any signal line below module whenever possible, No ground plane below antenna, If possible, cut-off the portion of main board PCB below antenna. Installation Notes (1) Reflow soldering is possible twice based on the time-temperature profile in this data sheets. Set up the temperature at the soldering portion of this product according to this reflow profile. (2) Carefully position the products so that their heat will not burn into printed circuit boards or affect the other components that are susceptible to heat. (3) Carefully locate these products so that their temperatures will not increase due to the effects of heat generated by neighboring components. (4) If a vinyl-covered wire comes into contact with the products, then the cover will melt and generate toxic gas, damaging the insulation. Never allow contact between the cover and these products to occur. (5) This product should not be mechanically stressed or vibrated when reflowed. (6) If you want to repair your board by hand soldering, please keep the conditions of this chapter. (7) Do not wash this product. (8) Refer to the recommended pattern when designing a board. (9) Pressing on parts of the metal cover or fastening objects to the metal will cause damage to the unit. (10) For more details on LGA (Land Grid Array) soldering processes refer to the application note. Usage Condition Notes (1)Take measures to protect the unit against static electricity. If pulses or other transient loads (a large load applied in a short time) are applied to the products, check and evaluate their operation before assembly on the final products. (2)Do not use dropped products. (3)Do not touch, damage or soil the pins. (4) Follow the recommended condition ratings about the power supply applied to this product. (5)Electrode peeling strength: Do not add pressure of more than 4.9N when soldered on PCB (6) Pressing on parts of the metal cover or fastening objects to the metal cover will cause damage. (7) These products are intended for general purpose and standard use in general electronic equipment, such as home appliances, office equipment, information and communication equipment. 24 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 Storage Notes (1)The module should not be stressed mechanically during storage. (2)Do not store these products in the following conditions or the performance characteristics of the product, such as RF performance will be adversely affected: • Storage in salty air or in an environment with a high concentration of corrosive gas. • Storage in direct sunlight • Storage in an environment where the temperature may be outside the range specified. • Storage of the products for more than one year after the date of delivery storage period. (3) Keep this product away from water, poisonous gas and corrosive gas. (4) This product should not be stressed or shocked when transported. (5) Follow the specification when stacking packed crates (max. 10). Safety Conditions These specifications are intended to preserve the quality assurance of products and individual components. Before use, check and evaluate the operation when mounted on your products. Abide by these specifications, without deviation when using the products. These products may short-circuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated when a short circuit occurs, then provide the following failsafe functions, as a minimum. (1)Ensure the safety of the whole system by installing a protection circuit and a protection device. (2)Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a dual fault causing an unsafe status. Other Cautions (1)This specification sheet is copyrighted. Reproduction of this data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. (2)Do not use the products for other purposes than those listed. (3)Be sure to provide an appropriate failsafe function on your product to prevent an additional damage that may be caused by the abnormal function or the failure of the product. (4)This product has been manufactured without any ozone chemical controlled under the Montreal Protocol. (5)These products are not intended for other uses, other than under the special conditions shown below. Before using these products under such special conditions, check their performance and reliability under the said special conditions carefully to determine whether or not they can be used in such a manner. 25 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 • In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where liquid may splash. • In direct sunlight, outdoors, or in a dusty environment • In an environment where condensation occurs. • In an environment with a high concentration of harmful gas. (6) If an abnormal voltage is applied due to a problem occurring in other components or circuits, replace these products with new products because they may not be able to provide normal performance even if their electronic characteristics and appearances appear satisfactory. (7) When you have any question or uncertainty, contact Fanstel. Packaging Production modules are delivered in reel, 1000 modules in each reel. FCC LABEL The Original Equipment Manufacturer (OEM) must ensure that the OEM modular transmitter must be labeled with its own FCC ID number. This includes a clearly visible label on the outside of the final product enclosure that displays the contents shown below. If the FCC ID is not visible when the equipment is installed inside another device, then the outside of the device into which the equipment is installed must also display a label referring to the enclosed equipment The end product with this module may subject to perform FCC part 15 unintentional emission test requirement and be properly authorized. This device is intended for OEM integrator only. 26 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 Revision History • September 2018 Version 0.20: initial draft release. 27 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 6.Contact Us United States: Fanstel Corp. 7466 E. Monte Ctisto Ave. Scottsdale AZ 85260 Tel. 1 480-948-4928 Fax. 1-480-948-5459 Email: module@fanstel.com Website: www.fanstel.com Taiwan: Fanstel Corp. 10F-10, 79 Xintai Wu Road Xizhu, New Taipei City, Taiwan 22101 泛世公司 臺灣省新北市汐止區新臺五路 79 號 10 樓之 10, 22101 Tel. 886-2-2698-9328 Fax. 886-2-2698-4813 Email: tp@fanstel.com Website: www.fanstel.com China: Fanstel Technologies Corp. 11 Jiale Street Ping-Dih, Long-Gang, Shen Zhen, GD 518117 泛世康科技(深圳)有限公司 廣東省深圳市龍崗區坪地鎮佳樂街 11 號 Tel. 86-755-8409-0928 Fax. 86-755-8409-0973 QQ. 3076221086 Email: sz@fanstel.com Website: www.fanstel.com 28 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation of the device. FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 29 BC840/M/E, Compact BLE 5, Thread, Zigbee ModulesVer 0.30 Dec. 2018 Canada, Industry Canada (IC) This Class B digital apparatus complies with Canadian ICES-003 Cet appareil numérique de classe B est conforme à la norme NMB-003. This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the Le present appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence.L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage adioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Canada, avis d'Industry Canada (IC) “Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement." Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements ISEDétablies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. (Modular approval) End Product Labeling: The final end product must be labeled in a visible area with the following: “Contains IC: 4100A-BC840M”. Caution: Exposure to Radio Frequency Radiation. To comply with RSS 102 RF exposure compliance requirements OEMstatement The Original Equipment Manufacturer (OEM) must ensure that the OEM modular transmitter must be labeled with its own FCC ID number. This includes a clearly visible label on the outside of the final product enclosure that displays the contents shown below. If the FCC ID is not visible when the equipment is installed inside another device, then the outside of the device into which the equipment is installed must also display a label referring to the enclosed equipment The end product with this module may subject to perform FCC part 15 unintentional emission test requirement and be properly authorized. This device is intended for OEM integrator only 30
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Create Date : 2019:03:07 09:34:07+08:00 Modify Date : 2019:03:07 09:34:07+08:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Title : untitled Producer : Acrobat Distiller 10.1.16 (Windows) Document ID : uuid:ec0d8188-1571-4d23-82ab-bd37f1648124 Instance ID : uuid:d803c3de-1089-49f2-a94d-fce00de4f1e8 Page Count : 30EXIF Metadata provided by EXIF.tools