Fantom Vacuum Cleaner Fm625H Users Manual 1

Fantom Vacuum Vacuum Cleaner FM625H FM625H_REV_1104A

FM625H to the manual 613e7ea8-53b8-462f-8829-567aa82b0397

: Fantom-Vacuum Fantom-Vacuum-Fantom-Vacuum-Vacuum-Cleaner-Fm625H-Users-Manual-550693 fantom-vacuum-fantom-vacuum-vacuum-cleaner-fm625h-users-manual-550693 fantom-vacuum pdf

Open the PDF directly: View PDF .
Page Count: 8

COMMERCIAL LIGHTWEIGHT

UPRIGHT VACUUM

OWNER’S MANUAL

Model FM625H

120V., 60Hz., 12 Amps

FOR HOUSEHOLD OR COMMERCIAL USE

FANTOM

94 Main Mill Street, Door 16

Plattsburgh, NY 12901

Tel.: 1 (800) 275-9251

When using electrical appliance, basic safety precautions should always be observed to

reduce the risk of fire, electric shock or injury, including the following:

1. Read all instructions before using your

vacuum.

2. Use only as described in this manual. Use

only manufacturer’s recommended

accessories. Use the vacuum only for its

intended use.

3. To protect against a risk of electric shock,

do not immerse any part of the system in

water or other liquids.

4. Never yank cord to disconnect from outlet;

instead, grasp plug and pull to disconnect.

5. Do not pull cord, use cord as a handle, close

a door on cord, or pull cord around sharp

edges or corners. Keep cord away from

heated surfaces.

6. Do not leave the vacuum plugged in when

unattended. Unplug the electrical cord when

not in use and before servicing.

7. Turn off all controls as applicable before

unplugging from electrical outlet.

8. Do not handle plug or hand vacuum with wet

hands or operate without shoes.

9. Do not allow cord to touch hot surfaces.

10. Do not run appliance over cord.

11. Do not operate the system with a damaged

cord or plug, or if the appliance or any other

part of the system has been dropped or

damaged. To avoid the risk of electric

shock, do not disassemble or attempt to

repair the vacuum. Return the unit to

FANTOM (see warranty) for examination

and repair. Incorrect re-assembly or repair

can cause a risk of electrical shock or injury

to persons when the vacuum is used.

12. Close supervision is necessary for any

appliance being used by or near children.

13. Do not leave the system unattended while

connected.

14. Do not allow to be used as a toy. Close

attention is necessary when used by or near

children, pets or plants.

15. Keep hair, loose clothing, fingers and all

parts of body away from opening and

moving parts.

16. Do not use vacuum to pick up flammable

or combustible liquids such as gasoline or

use in areas where they may be present.

17. Do not pick up anything that is burning or

smoking such as cigarettes, matches or

hot ashes.

18. Use extra care when cleaning on stairs.

19. Do not use the vacuum without all the

filters in place.

20. Use only extension cords UL-rated or cUL

at 15 amperes. Extension cords rated for

less amperage may overheat. Care should

be taken to arrange the cord so that the

cord cannot be pulled or tripped over.

21. Do not put any objects into openings. Do

not use with any opening blocked. Keep

free of dust, lint, hair and anything else that

may reduce air flow.

22. Store your appliance indoors in a cool, dry

area.

23. Keep your work area well lit.

24. Keep end of hose, wands and other

openings away from your face and body.

25. Do not use outdoors or on wet surfaces.

Use only on dry surfaces.

26. Using improper voltage may result in

damage to the motor and possible injury to

the user. Correct voltage is listed on rating

label.

27. If the supply cord of this appliance is

damaged, it must only be replaced by

FANTOM, because special purpose tools

are required.

28. Connect to a properly grounded outlet

only. See grounding instructions.

Model FM625H

ONE (1) YEAR LIMITED WARRANTY

FANTOM warrants this product to be free from defects in material and workmanship for a period of

one (1) year from the date of the original purchase, when utilized for normal commercial or household

use, subject to the following conditions, exclusions and exceptions.

If your appliance fails to operate properly while in use under normal household conditions within the

warranty period, return the complete appliance and accessories, freight prepaid to:

FANTOM, 94 Main Mill Street, Door 16, Plattsburgh, N.Y. 12901

If the appliance is found by FANTOM to be defective in material or workmanship, FANTOM will repair

or replace it free of charge. Proof of purchase date and $14.95 to cover the cost of return shipping

and handling must be included. *

Non-durable parts including, without limitation, filters, brushes and electrical parts which normally

require replacement are specifically excluded from warranty.

The liability of FANTOM is limited solely to the cost of the repair or replacement of the unit at our

option. This warranty does not cover normal wear of parts and does not apply to any unit that has

been tampered with or used for commercial purposes. This limited warranty does not cover damage

caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in

transit. This warranty does not cover damage or defects caused by or resulting from damages from

shipping or repairs, service or alterations to the product or any of its parts, which have been

performed by a repair person not authorized by FANTOM.

This warranty is extended to the original purchaser of the unit and excludes all other legal and/or

conventional warranties. The responsibility of FANTOM if any, is limited to the specific obligations

expressly assumed by it under the terms of the limited warranty. In no event is FANTOM liable for

incidental or consequential damages of any nature whatsoever. Some states do not permit the

exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from

state to state.

*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of

purchase date and to attach tag to item before packing with your name, complete address and

phone number with a note giving purchase information, model number and what you believe is

the problem with item. We recommend you insure the package (as damage in shipping is not

covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER

SERVICE”. We are constantly striving to improve our products, therefore the specifications

contained herein are subject to change without notice.

----------------------------------------------------------------------------------

OWNERSHIP REGISTRATION CARD

Please fill out and mail the product registration card within ten (10) days of purchase. The registration will enable us

to contact you in the unlikely event of a product safety notification. By returning this card you acknowledge to have

read and understood the instructions for use, and warnings set forth in the accompanying instructions.

RETURN TO EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901

_________________________________________________________________________________________

Appliance model

________________________________________________________________________________________

Date purchased Name of store

_________________________________________________________________________________________

Owner’s name

________________________________________________________________________________________

Address City State Postal code

SAVE THESE INSTRUCTIONS

For Household or Commercial Use Only

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should malfunction or breakdown,

grounding provides a path of least resistance for electric current to

reduce the risk of electric shock. This appliance is equipped with a cord

having an equipment-grounding conductor and grounding plug. The plug

must be inserted into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment-grounding conductor

can result in a risk of electric shock. Check with a qualified electrician or

service person if you are in doubt as to whether the outlet is properly

grounded. Do not modify the plug provided with the appliance - if it will

not fit the outlet, have a proper outlet installed by a qualified electrician.

This appliance is for use on a nominal 120-volt circuit, and has a

grounding attachment plug that looks like the plug illustrated at right.

Make sure that the appliance is connected to an outlet having the same

configuration as the plug. No adaptor should be used with this appliance.

Model FM625H

IMPORTANT SAFETY INSTRUCTIONS

Printed in China 12 1 Rev. 11/04A

PRECAUTIONARY MEASURES ORDERING REPLACEMENT HEPA DUST CUP FILTERS

3. Before you start vacuuming, make

sure to remove large or sharp objects

that might damage the debris screen.

1. Do not operate the vacuum cleaner

too close to heaters, radiators or

cigarette butts.

2. Before inserting the power plug into

the wall outlet, make sure that your

hands are dry.

4. When pulling out the power plug

from the wall outlet, pull the plug not

the power cord.

IMPORTANT: If the suction opening in the unit or the hose is BLOCKED, switch off

the vacuum cleaner and remove the blocking substance before you start the unit

again.

Call: 1 (800) 275-9251

Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time

TO ORDER REPLACEMENT HEPA FILTERS

Item XF621H

for Model FM625H

Call: 1 (800) 275-9251

Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time

FOR TECHNICAL SUPPORT

for Model FM625H

Please Note:

The HEPA Filter is washable. It should, however, be replaced every three (3) to six

(6) months depending on usage to ensure peak performance of your vacuum.

The exhaust filters and filter ring are rinseable. They should however be replaced

every three (3) months to ensure peak performance of your vacuum.

Important:

Make sure that ALL filters have been completely air dried for 24 hours before re-

installing back in the vacuum.

5. Do not pick up anything that is

burning or smoking such as

cigarettes, matches or hot ashes.

6. Do not use without all filters in

place.

211

TROUBLE SHOOTING GUIDE GETTING TO KNOW YOUR BAGLESS STICK VAC

PROBLEM POSSIBLE REASON POSSIBLE SOLUTION

VACUUM WILL

NOT OPERATE

1. Power cord not firmly plugged

into outlet.

2. No power in wall outlet.

3. Needs servicing.

4. Thermostat has tripped.

1. Plug unit in firmly.

2. Check fuse or breaker. Replace

fuse/reset breaker.

3. Call 1-800-275-9251.

4. Turn the unit off and unplug

from outlet. Allow unit to cool

down, then restart.

VACUUM WILL

NOT PICK-UP OR

SUCTION POWER

IS WEAK

1. Dust cup is full.

2. Unit clogged.

3. HEPA Filter needs cleaning

or replacing.

4. Debris screen needs

cleaning.

5. Exhaust filters or filter ring

needs cleaning.

1. Empty and clean dust cup.

2. Turn unit off and unplug from

wall outlet. Remove Dust Cup

Filter and check for object(s) in

air duct and remove.

3. Clean or replace HEPA Filter.

4. Clean debris screen.

5. Clean exhaust filters and filter

ring.

DUST ESCAPING

FROM VACUUM

1. Dust cup is full.

2. Dust Cup is not installed

correctly.

1. Empty and clean dust cup.

2. Review Dust Cup instructions.

VACUUM, HOSE

OR BRUSHES

WILL NOT PICK-

UP

1. Hose clogged.

2. Dust cup is full.

1. Remove hose and/or brushes.

Remove obstruction from hose

and /or brush.

2. Empty and clean dust cup.

1. Hand Grip

2. Hose Holder

3. Flexible Hose

4. Carrying Handle

5. Intelli-SenseTM Filter Monitor

6. On/Off Switch

7. Exhaust Filter Cover (x2)

8. Dust Cup Release

9. Dust Cup Cover

10. Dust Cup

11. Motorized Floor Brush

12. Hose Handle

13. Dusting Brush

14. Trap Door Release Button

15. Power Cord Quick Release

16. Extension Tube

17. Nozzle Release Pedal

18. Crevice Tool

19. Pet Hair Brush

20. Air Driven Turbo Brush

Technical Specifications

Voltage: 120V., 60Hz.

Power: 12 Amps

Illustrations may differ from actual product

10 3

OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS

Fig. 17

Exhaust

Filter

Cover

WARNING: Always remove the power

plug from the wall outlet before

assembling or removing accessories.

Inserting The Handle Into The Main

Unit

• Insert the handle into the hole on the

top of the unit. Make sure that the slot

in the handle fits correctly into the

opening. (Fig. 1)

• Insert the sleeve nut into the unit first.

Then holding the sleeve nut with your

thumb, insert the bolt. Using a flat

screw driver, secure the bolt to the

sleeve nut. (Fig. 1)

• To remove the

handle, you have

to remove the

bolt and the

sleeve nut.

Attaching The Motorized Floor

Brush To The Main Unit

• Insert the motorized floor brush into its

location at the bottom of the main unit,

in the direction of the arrow. (Fig. 2)

• Make sure that the motorized floor

brush is firmly inserted into the floor

brush socket.

• Insert the inlet hose into the floor brush

hose connector that is on the floor

brush. (Fig. 3)

Attaching The Hose To The

Main Unit

• Hold the end of the removable hose

handle and insert it into the hose

connector. (Fig. 3)

Fig. 2

Motorized Floor

Brush Hose

Connector

Hose

Connector

Fig. 3

Motorized

Floor Brush

Hose Connector

Inlet

Hose

Pin

Motorized Floor

Brush Release

Winding & Unwinding The Power

Cord

This vacuum cleaner is

equipped with a convenient

cord storage feature. The

power cord winds around

the two cord holders at

the back of the unit. The

top one has a quick

cord release feature.

Turn the cord hook to

the left or the right to

remove the power cord.

(Fig. 4)

When using the vacuum,

attach the power cord to

the cord holder so that

the power cord is out of

the way when you

are vacuuming.

(Fig. 5)

Fig. 4

Cord holder

Changing & Cleaning the Exhaust

Filter

The exhaust filter is a rinseable filter but

should be replaced every three (3) months.

• To remove the exhaust filter covers,

push the exhaust filter covers up.

Remove the filter. (Fig. 17)

• Rinse the exhaust filters in lukewarm

water and air dry the filters completely

for 24 hours. Do not use a washing

machine to rinse the filters. Do not use

a hair dryer to dry them. Air dry only.

Never operate the vacuum without the

exhaust filters in place.

• When the filters are

dry, replace into

the exhaust filter

covers and replace

on the vacuum.

• Severely soiled or

clogged filters should

be thoroughly rinsed with

fresh tepid water. A mild

detergent can be used

if required.

IMPORTANT:This unit is equipped

with a motor protective thermostat. If

for some reason the vacuum cleaner

should overheat, the thermostat will

automatically turn the unit off. Should

this occur:

• Push the On/Off button once.

• Disconnect the plug from the

power source.

• Check the source of overheating

problem. (i.e. clogged hose or

filter)

• If clogged hose or filter is found,

unclog the hose and replace the

filters.

• Wait at least 45 minutes before

attempting to reuse the vacuum.

• After unit has cooled down for

45 minutes, plug in the cleaner

and push the On/Off button. The

vacuum should start again.

• If the vacuum still does not start,

contact customer service at

1 (800) 275-9251.

Motor Thermostat

Cleaning the Filter Ring

1. Around the HEPA filter

there is a filter ring.

This is washable in

lukewarm water.

(Fig. 16) To remove

the filter ring, slide it

off the HEPA filter.

2. We recommend

washing the filter ring

when you are

washing your HEPA

filter. Always allow the

filter ring to air dry for 24 hours before

replacing onto the HEPA filter. Never

run the vacuum without all the filters in

place.

Fig. 16

Fig. 1

Sleeve nut Bolt

Fig. 5

49

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

On/Off Switch

The On/Off switch has three different

positions. (Fig.6)

• Push on the "I" side to turn the

vacuum ON. Set the vacuum here

when using the removable hose

handle with the accessories or when

vacuuming bare floors.

• Push on the “II" side to turn the

motorized floor brush on.

• Push on the “O” side to turn the

vacuum to the OFF position.

Using The Unit With The

Accessories

• Remove the removable

hose handle from

the hose connector.

• Attach the extension

tube, crevice tool,

the dusting brush,

pet hair brush or air

driven turbo brush

to the end of the

hose. (Fig. 8)

= OFF

= ON

(Bare Floors/Tools)

Using The Unit With The Motorized

Floor Brush

• Unwind the power cord and plug into

the 120V outlet.

• Press the On/Off switch to the “II”

position so that both the vacuum

and the motorized floor brush is

turned “ON”

NOTE: When vacuuming deep pile

carpets or hard wood floors, lower the

angle of the handle for easier

maneuverability. (Fig. 7)

= ON

(Carpet)

Fig. 6

Fig. 8

Fig. 7

Manual Variable Suction Control

Your vacuum cleaner includes a

variable suction control valve on the

hose handle. The suction power can be

adjusted by moving the slide to the

desired position. For example. Less

suction is required on upholstery and

draperies compared to thick shag

carpets, which require maximum

suction.

Dusting Brush

The dusting brush is used

for the furniture, venetian

blinds, books, lamp shades

and shelves.

Extension Tube

For hard to reach places. Use with

crevice tool or with dusting brush.

Wash

once a

month or

when

suction

appears

reduced

Fig. A

PLEASE NOTE: The white pleated

filter material in the HEPA Filter will

discolor over time -This is NORMAL

and will NOT affect the performance

of the filter. If the HEPA filter

is properly

"TapCleaned”

after each use

and suction

does not return

to 100%, then

we suggest that

the HEPA filter

be “TapCleaned”

vigorously until

no more dust

can be removed,

then rinsed under the faucet and

allowed to air dry for 24 hours before

refitting into the vacuum. (Fig. A)

This should be done once a month

or when suction appears to be

reduced.

Note: Even though the HEPA filter is

washable, it should be replaced every

3 to 6 months, depending on usage.

Warning: Allow 24

hours for drying before

replacing in unit.

Warning:Always empty the dust

cup container and clean the HEPA

filter, filter ring and debris screen

before each use and during

prolonged usage.

Never over fill the dust cup container -

remove dirt and clean the HEPA filter,

filter ring and debris screen when dirt in

dust cup is at or below the "MAX" level or

during prolonged usage because you

could risk damaging the motor.

If you wash the Hepa filter, make sure

that it has completely air dried for 24

hours before inserting back into the

vacuum.

Please Note: The HEPA Filter is

washable. It should, however, be

replaced every three (3) to six (6) months

to ensure peak performance of your

vacuum.

The filter ring and exhaust filter are also

rinseable but they should be air dried for

24 hours before replacing into the

vacuum. They should however be

replaced every three (3) months to ensure

peak performance of your vacuum.

Important: Make sure that ALL filters are

completely dry before re-installing back in

the vacuum.

2. To separate the filter assembly, hold

the bottom of the debris screen and

pull the dust cup cover out. Then

remove the HEPA filter with the filter

ring from the debris screen (Fig. 13)

3. Once you have removed the

HEPA filter from the debris

screen, remove the filter ring from

around the HEPA filter.

4. Vigorously “TapClean” the HEPA

filter on a hard surface until no

more dust is observed falling out.

(Fig. 14)

The HEPA

filter may also

be washed by

running it under

the tap allowing

the water to run on

the dirty side.

(Fig. 15) We

recommend

washing it once a

month or when

suction appears

reduced. Always

allow 24 hours for

air drying before

replacing into the vacuum.

Dust Cup

Cover

HEPA

Filter

Debris Screen

Fig. 13

Filter Assembly

Filter

Ring

Fig. 14

Warning: Never over fill the dust

cup - remove dirt and clean the

HEPA dust cup filter, filter ring and

debris screen each time the dust cup is

emptied during prolonged usage or risk

motor damage.

Fig. 15

Crevice Tool

For radiators, crevices, corners,

baseboards and between cushions.

Pet Hair Removal Brush

The pet hair removal brush

is for use on upholstery,

drapes and other fabric

surfaces to remove lint, pet

hair, etc. THE PET HAIR REMOVAL

BRUSH IS NOT INTENDED TO BE

USED AS A PET GROOMING

DEVICE.

8 5

OPERATING INSTRUCTIONS

Emptying the Dust Cup Container

Warning: Always unplug the

unit from electrical outlet before

opening the Dust Cup (container).

Fig. 11

Fig. 10

2. To empty the dust cup container,

hold the dust cup from the top over a

garbage container and press on the

trap door release button that is on

the front side of the dust cup

container to release the dust cup

bottom (Fig. 11)

When the Intelli-SenseTM Filter

Monitor lights up, it means that the

dust cup is full or the HEPA filter, filter

ring and debris screen need cleaning.

You must empty the dust from the

dust cup and clean the HEPA filter,

filter ring and debris screen right

away.

Intelli-SenseTM Filter Monitor

Hold

Push

Cleaning the HEPA Filter

Warning:After each Use -

Always remove the Filter

Assembly, then vigorously “TapClean”

HEPA Filter and clean Debris Screen

and Filter Ring until no more dust can

be removed.

IMPORTANT, Please Note : The

“TapClean” HEPA Filter will stop most of

the tiniest dust particles from re-entering

the air you breathe. In fact it stops

99.97% of all particles as small as 0.3

microns - many times smaller than a

human hair!!! Because of this incredible

filtration performance, the HEPA Filter

will quickly accumulate, inside the white

filter folds, many fine dust particles that

are difficult to see but which will

eventually block or reduce your suction

power - if not cleaned properly.

1. To remove the filter assembly from

the dust cup, hold the dust cup

container in one hand and with the

other hand, turn counter clockwise

and pull out the filter assembly.

(Fig. 12)

Filter Assembly

Dust Cup

Container

OPERATING INSTRUCTIONS

Important: In order to ensure that

maximum air suction is maintained,

empty the dust cup frequently and tap

clean the HEPA filter, filter ring and

debris screen at the same time. Ensure

that the rotating brush is kept free of hair

and string which may accumulate and

decrease brush performance.

Using The Unit With Air Driven

Turbo Brush

Turbine

Tilt

Upwards

Locking Latch

From time to time, the turbine of your

turbo brush will require cleaning. To do

this:

1. Remove the turbo brush from the hose

or telescopic extension tube.

2. Slide locking latch forward then tilt the

top housing of the brush upwards. The

top housing is hinged and will tilt up

approximately 45° only.

3. There may be some dust, lint, hair, etc

on the turbine wheel. Remove as much

of this as possible.

4. You may also use the unit’s hose with

crevice tool attached and use the

vacuum to remove any additional

debris from the turbine.

5. Ensure that the turbine wheel moves

freely by rotating it with your finger. If

the turbine does not rotate, call

Customer Service for help.

6. Once clean, close the top cover of the

turbo brush and slide the locking latch

toward the rear of the brush to lock.

To use the air driven turbo brush to

clean upholstery:

1. Remove the flexible hose from the

hose connector. (Fig. 9)

2. Push the air driven turbo brush onto

the end of the flexible hose as far as

it will go.

Cleaning Air Driven Turbo Brush

Fig. 9

The efficiency of your air driven turbo

brush depends on the bristle brush

rotating at high speed. Strong air suction

is needed to accomplish this. In order to

ensure that maximum air suction is

maintained, please read the following

instructions:

1. Empty the dust cup frequently.

2. Always vigorously “TapClean” the

HEPA filter, filter ring and the debris

screen when emptying the dust cup

container.

3. Ensure that the rotating brush is kept

free of hair and string which may

accumulate and decrease brush

performance.

4. Keep air driven turbo brush turbine

free of dirt and foreign matter. (See

illustration for cleaning instructions.)

Important: Do NOT use the vacuum

without the HEPA filter and filter ring in

place.

1. To remove the dust cup container,

press down on the dust cup release

and pull the dust cup container out

from the vacuum. (Fig. 10)

Attaching the Air Driven Turbo

Brush to the Flexible Hose

Fig. 12

6 7