Farsun Photoelectric Science Technologies FG2106 Bluetooth Barcode Scanner User Manual bt v2 0 en1 btw

Farsun Photoelectric Science Technologies co., LTD Bluetooth Barcode Scanner bt v2 0 en1 btw

Contents

User manual

3 .Bluetooth communication parameter settingsWhen the scanner is set too much,you can scan"Return to default" settings for Bluetoothrecovery settings code to allow the scanner toresume factory settings.①.Bluetooth restore the default SettingsReturn to default②.Bluetooth scanner and receiver matching methodPair Code③.Sleep modeScanner can scan the following Settings,to set upall kinds of sleep time.To extend batterylife,Suggest that sleep time shoulds not be set toolong.<Sleep time 20 Seconds>Sleep time 60 SecondsSleep time 2 MinutesSleep time 10 Minutes④.Normal ModeNormal mode ：Scan barcodes directly then thedecoded data transfer to the receiver anddisplayed on the PC or your host ,But if thetransmission fails (for example, over thetransmission distance or the receiver is not open),then issue "di da " sound prompts the user totransmission failure.Normal Mode⑤. Inventory modeWhen the scanner is not in the receiver's operatingrange, please use the Inventory mode First you canset up the mode "Inventory mode" then you scan thebarcodes ,the data will be stored in the scanner. Inventory modeNote:When using "Inventory Mode",the user need toscan the clear data set code will scanner memoryempty.Transfer dataTotal Number of dataClear data4.Bluetooth scanner auxiliary functionsBluetooth keyboard is fast<Bluetooth keyboard is slow>⑥.Wired model2 .Bluetooth barcode scanner performance parametersCommunication distance: Indoor 7~10mCommunication protocol: Bluetooth 3.0Compatibility: iOS,Mac,Android,XP,Win7 etc.Data memory: 4096Byte FlashScanning type: manual single scan/continuousscanning/automatic scanningSource: LED（622nm-628nm）The maximum scanning speed: 200 times/secDecoding accuracy: more than 3.3milDepth of focus：3.3mil:2mm-100mm10mil:2mm-350mm15mil:5mm-500mm30mil:10mm-800mmDecoding IC: 32bit high-speed processorPCS ：The minimum reflectivity of 30%working current: Decoding the current 40mA,workingcurrent 20mA,Standby current 5mA,shutdown current18uA,Internal constant current constant voltagecharging,Support while charging work.Charging source: 5V 500mA.Charging time: 1.5 hour.Service time: 30 hour.Scan Mode: Two-way single.prompting mode：Buzzer + lightError rate: 1 / 5000000Scanning angle: rotation angle±30°, Oblique Angle±45°, deflecting angle ±60°.Decoding ability: UPC-A, UPC-E, EAN-8, EAN-13, Code 128, Code 39, Code 39 Full ASCII,Codabar/NW7, Code 93, Code 11, MSI, Interleaved 25,Industrical 25, ISBN, ISSN, China Post etc.Domesticgeneral one-dimensional codes.Support interface : USB HID, USB Virtual Serial(Needto drive and setup code please contact the dealer)The seismic test：Many times from 1.5 meters heightfell to the ground of concrete can still worknormally after impact.Authentication：CE,FCC,RoHS,ClassIBluetooth barcode scanner characteristics*.Wireless operation, convenient to carry, usingflexible workplaces;*.Power rechargeable, can also transmit data,using a shortcut;*.With fine ability to decode;*.Key is comfortable, life one million times;*.Storage mode support extreme distance work;*.750mAh Large capacity lithium battery,persistent work;*.Support Windows XP, Win 7,Androld,iOS,MacPacking detail: a scanner, a receiver, a USBcharging line, a simple description.1 .Bluetooth barcode scanner overviewProduct appearance figureBarcode read correctlyWhen you use the USB cable ,the scanner willchange the wireless mode into wired mode .You also can close the wire mode ，please scan thefollow barcode.Wired mode Off<wired mode On>4/72/7 3/71/7Bluetooth barcode scanner operation points for attention①.Take out the receiver,Plugged into PC(POS)USBInterface,After waiting for the computer toinstall the driver(About 3 to 5 seconds, neednot operation, the computer automatically),Themouse cursor in the need to enter the barcode inthe text box,You can scan you need to enter thebar code.②.Cable model methods of use：Plugged intoPC(POS)USB Interface,immediate use.③.General fault repair methods：The USBreceiver to plug,Then scan"Defalut"setting.The scanner needs and receiver after the match,Can be usednormally.To match the receiver insert a computer USBinterface,After waiting for it into the working state,Byscanner scan "Pair Code"Settings,At this point, the red andblue lights flashing, said in the matching state, theautomatic search the bluetooth devices around, when thebuzzer sends out "di di" sound, light blue, said the matchis successful, can transmit dataAfter finishing thematching,Scan version information Settings to observewhether a match,If success shows versioninformation,Otherwise the match fails,need to match.Short RangeMedium Range<Long Range>Bluetooth reliability setting,High reliability,Transmission distance near;Low reliability,Transmission distance far.①.Reliability settings②.Matching settingsRemoval of matchDisconnect the existingConnect the host matchesShutdown③.Transmission speed settings<HID Mode>SPP Mode④.Transmission mode settingsAutomatic ON<Automatic Off>⑤.Automatic settings⑥.iOS keyboard show/hide SettingsShow/hide the iOS keyboardFastMedium<Slow> （Note：Automatic function optional,Defaultsingle mode.If need to open Automatic mode,youcan hold down the switch 8 seconds,Can switch tothe Automatic mode,If you need to shut downAutomatic mode that the same operation）Double click the button quickly to turn on /offthe IOS keyboard ,when you have no manual book .Transmission speed settings(Inventory mode only)
Start/stop characters ON<Start/stop characters Off>Start/stop characters ON<Start/stop characters Off>UPC-E convert UPC-A ON<UPC-E convert UPC-A Off>UPC-A convert EAN-13 ON<UPC-A convert EAN-13 Off><UPC/EAN Supplementals Code Off>2 bit Supplementals Code ON5 bit Supplementals Code ON2&5 bit Supplementals Code ONUPC/EAN SettingsCode 39 SettingsCodabar SettingsTerminator<CR>LFCR+LFTABNoneWith a set of symbols "< >" said as the default.note！7/7Bluetooth barcode scannerUser's manualVer : bt-v2.0 enBar code type to chooseCode 39 Full ASCII ON<Code 39 Full ASCII Off>ISBN Code ON<ISBN Code Off>Invert case Change UppercaseCharacter case conversionUPC/EAN Settings<UPC-A systematically ON>UPC-A systematically Off<UPC-E systematically ON>UPC-E systematically Off<UPC-A Check digit ON>UPC-A Check digit Off<UPC-E Check digit ON>UPC-E Check digit Off<EAN-13 systematically ON>EAN-13 systematically Off<EAN-8 systematically ON>EAN-8 systematically Off<EAN-13 Check digit ON>EAN-13 Check digit Off<EAN-8 Check digit ON>EAN-8 Check digit OffReset to DefaultsVersion InformationInterface selection <USB HID mode>USB Virtual-serial modeVolume Off<Volume High><Single scan>Continuous scan<USA Keyboard>German KeyboardFrench KeyboardItalian KeyboardSpain KeyboardPortugal KeyboardBarcode type ID ON<Barcode type ID Off>BuzzerReading modeKeyboard LanguageBarcode type ID<Inversion of barcode image ON>Inversion of barcode image Off5/7Barcode prefix STXBarcode suffix ETXBarcode image and settingBarcode character settingChange Lowercase<Cancel the case set>5.General barcode settings6/7DefaultsBattery Status⑦.Battery StatusVolume MediumVolume LowRepeat barcode ON<Repeat barcode Off>Repeat barcode Interval 1SRepeat barcode Interval 10SRepeat barcode setting(This function is only used in Wired mode)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.
Warnings: This device complies with Industry Canada’s licence-exempt RSSs Operation is subject to the following two conditions: (1) This device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur

Navigation menu