Faurecia Clarion Electronics FZ502 CAR AUDIO User Manual
Clarion Co Ltd CAR AUDIO Users Manual
UserManual.wiki
>
Faurecia Clarion Electronics
>
FZ502 User Manual
Users Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![English3FZ502Front Panel / GeneralitiesFor a longer service life, be sure to read the following cautions.• Do not allow any liquids on the set from drinks, umbrellas, etc. Doing so may damage the internal circuitry.• Do not disassemble or modify the set in any way. Doing so may result in damage.• Do not let cigarettes burn the display. Doing so may damage or deform the body.• If a problem should occur, have the set inspected at your store of purchase.[CONTROL] Knob• Power on (press)• Power off (long press -> rotate it select “POWER OFF“ ->press)• Adjust volume level (rotate)• Toggle the audio source (press)• Previous/Next search (press - left/right )• Select tuner band (press - up)(long press)• BT mode – Terminate call• RADIO mode – No function.• HD RADIO mode – SUB channels select.• SIRIUS mode – Direct search• AUX mode – No function.• USB mode – Search function• iPod mode – iPod menu[ MIC ] Hole • Internal microphone3. CONTROLSOperational PanelNames of Button[CONTROL] [RESET] USB Slot[MIC] AUX ININFORMATION FOR USERS:Changes or modifications to this product unapproved by the manufacturer will void the warranty and will violate FCC approval.Cleaning the body• Use a soft, dry cloth and gently wipe off the dirt. • For tough dirt, apply some neutral detergent diluted in water to a soft cloth, wipe off the dirt gently, then wipe again with a dry cloth. • Do not use benzene, thinner, car cleaner, etc., as these substances may damage the body or cause the paint to peel. Also, leaving rubber or plastic products in contact with the body for long periods of time may cause stains.USB Port• The USB memory stick may stick out when inserted,so it may cause danger during driving. When connect USB memory stick to the main unit, please use a USB extension cable (CCA-755).• The USB memory sticks must be recognized as “USB mass storage class“ to work properly. Some models may not operate correctly. When the memorized data is lost or damaged by any chance, Clarion shall not be liable for any damage. When using an USB memory stick, we recommend that you backup your data stored on it before using a personal computer etc.• Data les may be broken when using USB memory sticks in the following situation: When disconnecting the USB memory stick or turning the power off during reading data. When affected static electricity or electric noise. Connect/disconnect the USB memory stick when it is not accessed.• Connecting with the computer is not covered.FCC ID: AX2FZ502CHINA530-1710kHz 87.9-107.9MHzBluetooth QD ID No.: B017439 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:(1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2)THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.THIS DEVICE COMPLIES WITH DHHS RULES 21 CFR CHAPTER I SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE.CLARION CO.,LTD.7-2,SHINTOSHIN,CHUO-KU,SAITAMA-SHI,SAITAMA-KEN,JAPANThis product includes technology owned by Microsoft Corporation andcannot be used or distributed without a license from MSLGP.MANUFACTURED:URFHD Radio™, HD Radio Ready™, and the HD Radio Ready logo are proprietary trademarks of iBiquity Digital Corporation.PN:12707000XXXXTX-10XXX-X](https://usermanual.wiki/Faurecia-Clarion-Electronics/FZ502/User-Guide-1602125-Page-4.png)
![English4FZ502Remote Control (RCX003)Notes of remote control usingReplacing the lithium battery of remote control unit.When the range of the operation of the card remote control becomes short or no functions while operating. Replace the battery with a new lithium battery. Make sure the battery polarity replacement is correct.1. Pull out the battery holder while pressing the stopper. 2. Insert the button-type battery with the stamped(+) mark facing upward. Insert the battery holder into the remote control.[SRC/ ] Button• Toggle the audio source• Power on ( short press) / off (long press)[ , ] Buttons• Preset station up / down• Previous / next track• Search (long press)[SCN/PS/AS] Button• Scan play / Preset scan• Auto memory store (long press)[BAND/TOP] Button• MP3/WMA mode – Top play (long press)• HD RADIO mode – Select tuner band• SIRIUS mode – Select tuner band/Select category (long press)[ , ] Buttons• Volume up / down[ ] Button• Play / Pause[ISR] Button• Recall ISR station stored in memory• Store current station in ISR memory (long press)• iTunes Tagging (When connected with HD Radio tuner and displayed ”DIGITAL” indicator and ”TAG” indicator on display at HD Radio-mode.)[DISP] Button• Display switch[RDM] Button • Random play[RPT] Button • Repeat play[MUTE] Button• Mute the volume[1~6] Buttons • [1] Button: Preset station 1. • [2] Button: Preset station 2. • [3] Button: Preset station 3. • [4] Button: Preset station 4. • [5] Button: Preset station 5. • [6] Button: Preset station 6.[SOUND] Button • Sound effect setting(CR 2025)CR 2025[ , ][ISR][RPT][SOUND][RDM][ , ][DISP][1~6] [MUTE][SCN/PS/AS][ ][BAND/TOP][SRC/ ]4. OPERATIONSBasic OperationsNote:• Refer to the diagrams in “3. CONTROLS” when reading this chapter.CAUTIONWhen the unit is turned on, starting and stopping the engine with its volume raised to the maximum level may harm your hearings. Be careful about adjusting the volume.Power on / offNotes:• Start the engine before using this unit.• Be careful about using this unit for a long time without running the engine. If you drain the car’s battery too far, you may not be able to start the engine and this can reduce the service life of the battery.1. Start the engine. The power button / knob illumination on the unit will light up. Engine ON position2. Press the [CONTROL] knob on the front panel or [SRC / ] button on the remote control to turn on the power under standby mode. The unit goes back to the last status after power on.3. Press and hold the [CONTROL] knob (center long press) on the front panel, and rotate the [CONTROL] knob choose POWER OFF, then press the [CONTROL] knob on the front panel to turn off the power. Or press and hold [SRC / ] button on remote control to turn off the power.MutePress the [MUTE] button on the remote control to mute the volume from the unit.Note: Doing the operation above again or adjusting volume will release muting.RESETVolume adjustmentTurn the [CONTROL] knob on the front panel.The adjustable range of volume is 0 to 40.CAUTIONWhile driving, keep the volume level at which external sounds can be heard.Playing source selectionPress [CONTROL] knob on the front panel repeatedly to choose desired playing source.Notes:• Playing source selection means selecting work mode, such as RADIO mode and AUX mode, etc.Display system timePress the [DISP] button on the remote control to switch the display information, system time and playing source.RESETNote:* When the [RESET] button is pressed,frequencies of radio stations, titles, etc.stored in memory are cleared.](https://usermanual.wiki/Faurecia-Clarion-Electronics/FZ502/User-Guide-1602125-Page-5.png)
![English5FZ502At all mode, press and hold [CONTROL] knob (center long press), and rotate the [CONTROL] knob choose ADJUST, then press the [CONTROL] knob to enter system setup. Press [CONTROL] knob (left / right) to select options, rotate the [CONTROL] knob to adjust. CLOCKPress the [CONTROL] knob (right) to choose minute, and rotate the [CONTROL] knob to set minute.Press the [CONTROL] knob (left) to choose hour, and rotate the [CONTROL] knob to set hour.Then long press [CONTROL] knob (center) to conrm the time setting.PASSWORD (SIRIUS mode)Press the [CONTROL] knob to enter old password, rotate the [CONTROL] knob to select a digit, press the [CONTROL] knob (left / right) to move the cursor. Press the [CONTROL] knob to confirm after input all 4 digit. Then input a new 4-digit number as above. (Original password: 0000)LOCK (SIRIUS mode)Press the [CONTROL] knob to lock current station, rotate the [CONTROL] the knob to select a digit, press the [CONTROL] knob (left / right) to move the cursor. Long press the knob to confirm after input all 4 digit password.UNLOCK (SIRIUS mode)Press the [CONTROL] knob to unlock all locked stations, rotate the [CONTROL] knob to select a digit, press the [CONTROL] knob (left / right) to move the cursor. Press the [CONTROL] knob to conrm after input all 4 digit password.UNSKIP (SIRIUS mode)Press and hold the [CONTROL] knob to unskip all channels. DX/LO (RADIO mode)Rotate the [CONTROL] knob to choose radio local or distant at RADIO mode.• LO: Only stations with strong signal can be received.System Setup• DX: Stations with strong and weak signals can be received.PCH MEMO (RADIO/HD RADIO/SIRIUS mode)Rotate the [CONTROL] knob to choose PCH 1 / PCH 2 / PCH 3 / PCH 4 / PCH 5 or PCH 6, press and hold [CONTROL] knob (center long press) to store it in the memory.AUX SENS (AUX mode)Rotate the [CONTROL] knob to choose AUX input sensitivity LOW, MID or HIGH at AUX mode.AUTO CON (BT mode): ON/OFFRotate the [CONTROL] knob to choose AUTO CON ON or OFF.PIN CODEPress the [CONTROL] knob, rotate the [CONTROL] knob to select a digit, press the [CONTROL] knob (left / right) to move the cursor. Press the [CONTROL] knob to conrm.The PIN CODE default setting is “ 0000 “.MIC SEL (BT mode)Rotate the [CONTROL] knob to choose microphone EXTERNAL or INTERNAL.MIC GAIN (BT mode)Rotate the [CONTROL] knob to choose Mic gain: 1, 2, 3, 4, 5.You can change the gain of MIC when a telephone partner cannot hear your voice.SCRN SVR: ON/OFFRotate the [CONTROL] knob to choose SCRN SVR (screen saver) ON or OFF.SCROLL: ON/OFFFor track information that is longer than the display panel:When SCROLL is ON, the LCD will display ID3 TAG information cyclely, e.g.: TRACK->FOLDER->FILE->ALBUM->TITLE->ARTIST->TRACK->...When SCROLL is OFF, the LCD will display one of the ID3 TAG information, the default is TRACK, but user can adjust it to other ID3 System SetupTAG information by pressing [DISP] button on the remote control.S-CTRL (iPod mode) : ON/OFFRotate the [CONTROL] knob to choose S-CTRL (Simple control) ON or OFF.* Refer to P18.DIMMER: ON/OFFRotate the [CONTROL] knob to choose DIMMER ON or OFF.• ON: LCD dimmer is active when small light of vehicle is turned ON.• OFF: LCD always maximum brightness regardless of the vehicle small light.REAR/S-WRotate the [CONTROL] knob to choose REAR or S-WOOFER(SUB-WOOFER).SW PHASERotate the [CONTROL] knob to choose REVERSE or NORMAL.BEEP: ON/OFFRotate the [CONTROL] knob to choose button beep sound ON or OFF.SOUNDPress the [CONTROL] knob to enter sound effect setting mode. First press shows current EQ. Rotate the [CONTROL] knob to chooseBEAT EQ in this order:OFF -> B-BOOST -> IMPACT -> EXCITE -> CUSTOMTo change CUSTOM setting, and press the [CONTROL] knob (center), then press [CONTROL] knob (right/left) to select EQ effects including: BASS-G -> BASS-F -> BASS-Q -> MID-G -> MID-F -> MID-Q -> TREBLE-G -> TREBLE-F, rotate the [CONTROL] knob to select a value.BASS-G / MID-G / TREBLE-G: (-7)- (+7)BASS-F: 50 / 100 / 200BASS-Q : 0.7 / 1.0 / 1.4 / 2.0MID-F: 500 / 1K / 2K MID-Q: 0.7 / 1.0 / 1.4 / 2.0TREBLE-F: 5K / 10K / 15KTREBLE-Q: 0.7 / 1.0 / 1.4 / 2.0Then press the [CONTROL] knob (left / right) to select USER preset including:BALANCE -> FADER -> M-B EX ->HPF(high pass filter) -> LPF(low pass filter) -> S-W VO L (S u b wo o f er Vo l um e ) , r otate the [CONTROL] knob to select a value.BALANCE:LEFT 1-7->CENTER->RIGHT 1-7FADER:FRONT 1-7->CENTER->REAR 1-7M-B EX: ON/OFFHPF: THROUGH/60/90/120LPF: THROUGH/60/90/120SUBW VOL: (-6)-(+6)12/24HRotate the [CONTROL] knob to choose time format: 12 or 24 hour.Radio OperationsSelect tuner as playing sourcePress the [CONTROL] knob or [SRC / ]button on the remote control to switch to the RADIO source. Select one radio bandPress the the [CONTROL] knob (up long press ) on the panel or [BAND/TOP] button on the remote control to select one radio band among FM1, FM2, FM3 and AM.Manual tuningDuring manual tuning, the frequency will be changed in steps.Press the [CONTROL] knob (left/right) on the panel or [ , ] buttons on the remote control to tune in a higher / lower station.Auto tuningPress and hold [CONTROL] knob (left/right) on the panel or [ , ] buttons](https://usermanual.wiki/Faurecia-Clarion-Electronics/FZ502/User-Guide-1602125-Page-6.png)
![English6FZ502Radio OperationsSatellite Radio ModeSatellite Radio ModeListeners can subscribe to SIRIUS® Radio on the Web by visiting www.sirius.com, or by calling (888) 539-SIRIUS. Customers should have their SIRIUS ID ready (SIRIUS ID is located on the SC-C1 SIRIUS Connect Vehicle Tuner, solid separately). Customers can listen to music samples by tuning to channel 184.Accessing satellite radio modePress the [CONTROL] knob or [SRC / ] button on the remote control to switch to the SAT source. Displaying the Identication (ID) CodeBefore you listen to satellite radio, you must subscribe to the service using your radio’s identification number. To display the radio ID, use the [CONTROL] knob (left) or [ ] tuning button on the remote control to tune to channel “0”. The screen displays the radio ID where the channel name is usually displayed.Check SC-C1 SIRIUS Connect Vehicle Tunerthe remote control to seek a higher / lower station.To stop searching, repeat the operation above or press other buttons having radio functions.Note:When a station is received, searching stops and the station is played.Preset scan Preset scan receives the stations stored in preset memory in order. This function is useful when searching for a desired station in memory. 1. Press the [SCN/PS/AS] button on the remote control. 2. When a desired station is tuned in, press the [SCN/PS/AS] button on the remote controlagain to continue receiving that station. Note:Be careful not to press and hold the [SCN/PS/AS] button, otherwise the auto store function is engaged and the unit starts storing stations. Auto storeOnly stations with sufcient signal strength will be detected and stored in the memory.Press and hold the [SCN/PS/AS] button on the remote control to start automatic station search.To stop auto store, press other buttons having radio functions.Notes:1. After auto store, the previous stored stations will be overwritten.2. The unit has 4 bands, such as FM1, FM2, FM3 and AM. FM3 and AM can store by AS function. Each bands can store 6 stations, FZ501 can store 24 stations in total.Manual storeWhen one expected radio station has been detected, press and hold number button on the remote control 1-6 to store it in the memory.Recall the stored stationsPress one numeric button among 1 to 6 on the remote control or on the panel to select the corresponding stored station.Local seekingWhen LOCAL seeking is on, only those radio stations with strong radio signal could be received.Refer to System Setup page 9.Note:The number of radio stations that can be received will decrease after the local seeking mode is on.If SIRIUS tuner is not connected, “NO TUNER” will appear on the LCD.Select a bandPress the the [CONTROL] knob (up long press) on the panel or [BAND/TOP] button on the remote control to change between three SAT bands (SR1, SR2 and SR3). Each band stores up to six preset stations.Select a stationPress the [CONTROL] knob (left / right) on the panel or [ , ] buttons on the remote control to tune to another station. Preset modeSix numbered preset buttons on the remote control store and recall stations for each band. Preset scanShort press the [SCN/PS/AS] button on the remote control to start category scanning.Long press the [SCN/PS/AS] button on the remote control to start preset station scanning for 10 seconds each.Storing a station1. Select a band (if needed), then select a station.2. Press and hold a preset button (numbers 1-6) on the remote control.3. The preset number and station is displayed and highlighted.Recalling a station1. Select a band (if needed).2. Press a remote control preset button (numbers 1-6) to select the corresponding stored station.Category and Channel searchTo access Category and Channel Search mode, press the [CONTROL] knob (up long press) on the panel or [BAND/TOP] button on the remote control long press. 1. Rotate the rotary knob on the panel to select the desired category.2. Press the [CONTROL] knob (left / right) on the panel or [ , ] buttons on the remote control to select the channel name.Direct searchTo access Direct Search mode, press the [CONTROL] knob button on the front panel. 1. Rotate the [CONTROL] knob on the panel to select the desired direct, and press the [CONTROL] knob to confirm the selection. 2. Rotate the [CONTROL] knob on the panel or press the [ ] or [ ] button on the remote control to select the direct name, and press the knob to conrm the selection.PASSWORDRefer to System Setup page 9.LOCKRefer to System Setup page 9.UNLOCKRefer to System Setup page 9.UNSKIPRefer to System Setup page 9.](https://usermanual.wiki/Faurecia-Clarion-Electronics/FZ502/User-Guide-1602125-Page-7.png)
![English7FZ502HD Radio OperationsAbout HD Radio™ TechnologyHD Radio Technology allows CD-quality digital broadcasting of your local AM and FM radio stations. HD Radio broadcasts can include multiple channels on the same frequency, which is called multicasting. With multicasting, you can receive up to eight additional multicast channels: HD1~HD8. With an HD Radio tuner connected, you will receive HD Radio digital broadcasts automatically when tuned to a station that offers HD Radio Technology. NOTE: Not all FM or AM stations offer HD Radio (digital) broadcasting. You can receive both analog and digital stations with the unit.Accessing radio modePress the [CONTROL] knob or [SRC / ] button on the remote control to switch to the HD RADIO source, and HD icon will illuminate.Select a bandPress and hold the [CONTROL] knob (up long press) on the panel or [BAND/TOP] button on the remote control to change between three FM and one AM bands. Each band stores up to six preset stations.Tuning- Seek TuningPress and hold the [CONTROL] knob (left / right) on the panel or [ , ] buttons on the remote control to seek the next/previous station automatically. - Manual TuningPress the [CONTROL] knob (left / right) on the panel or [ , ] buttons on the remote control to move the radio frequency number up or down one step.HD Radio multicast channelsTo tune to an HD Radio multicast channel, tune to the main signal and then press the [CONTROL] knob on the panel. PTY and SUB CH are displayed. Select PTY or SUB CH by rotate [CONTROL] knob and push to conrm.• Select PTY type from the category list by rotate [CONTROL] knob and push.• Select SUB CH by rotate [CONTROL] knob and push.• Multi channel is available when a digital signal is detected, the DIGITAL icon will illuminate. If the digital signal becomes unavailable, the unit will revert to Analog reception.Preset stationsUp to six stations on each band can be stored as presets, which can then be instantly recalled by pressing the associated preset button. To store a station, turn the radio on and select the desired band and station. Press and hold the desired preset button (numbered one through six on the remote control). When stored, the preset number will appear in the display. The station is now stored and can be recalled by pressing the corresponding preset button. Repeat for the remaining five presets on the current band and for presets on the other four bands.NOTE: Multicast stations can be stored as presets, but the unit must be in Digital or Auto reception mode to receive them.Preset scanPress [SCN/PS/AS] button on the remote control to scan and play all preset stations for 10 seconds each. Press [SCN/PS/AS] button on the remote control again to stop scanning and play the current station.Note:Be careful not to press and hold the [SCN/PS/AS] button on the remote control, otherwise the auto store function is engaged and the unit starts storing stations.Automatic store (AS)Press the [SCN/PS/AS] button on the remote control to select six strong stations and store them in the FM3 or AM band using the auto store function. After entering the stations into memory, the unit will automatically stop at each station for ve seconds, allowing you to preview each selection. When using the auto store function, the new stations replace any stations already stored in preset memory.Note:You can stop the auto store function at any time by pressing the [SCN/PS/AS] button on the remote control again.iTunes® TaggingThe unit offers iTunes® Tagging, which allows the user to "Tag" songs playing on HD Radio™ stations for purchase later through iTunes. When press [ISR] button on the remote contorl, the unit stores the title and artist song information that can then be transferred to your iPod when connected to the unit. A list titled "Tagged" will appear in iTunes, allowing you the option to purchase your tagged songs.Note:“iTunes® Tagging” function works by connecting THD301 (sold separately).iPod compatibilityFor detailed information on the playable iPod models, see our home page: www.clarion.comNote:• iPhones can also be connected to this system and “iP od ” appearing in this manual should be referred to as “iPod/iPhone”.• This system will not operate or may operate improperly with unsupported versions.Tagging musicTo begin tagging music, tune to an HD Radio station. The DIGITAL icon at the display must be illuminated, indicating a digital station is being received. TAG icon lights up when Tagging function is ready. Press the [ISR] button on the remote control. The tagging function is highly depends on the receptions of the radio station. If the channel reception is insufcient, it will effect the operation of the tagging function.“Stored Tag ## of 64” will appear in the display. The song information is saved to the unit memory until your iPod is connected. You can tag up to 64 songs before the tags must be transferred to your iPod or deleted. When the Tag memory reaches capacity (64 tags) the bottom of the screen displays “Memory Full”.Table 5: TAG MessagesTag Message ReasonST O R E D TA G ## OF 64If the Tag data is ready, and [ISR] button on the remote control is pressedSENDING TAG ## Tag data is sending to iPodMEMORY FULL Tag storage is fullTAG DATA IS NOT AVAILABLETag data is not availableIPOD FULL iPod memory is fullTAG NOT SUPPORT When connect and press [ISR] button on the remote control, the iPod without Tagging functionNote:Tags saved to your iPod can be managed using the iTunes software, available at www.apple.com/itunes.Downloading tags to your iPodTo download tags to your iPod, plug your iPod into the unit. All existing tags are automatically transferred to the iPod and deleted from the head unit’s memory. If your iPod is connected when a song is tagged, the Tag will be immediately transferred to the iPod.Note:When transferring Tags to your iPod, the unit must remain in HD RADIO mode. To purchase tagged songs, you must sync your iPod to iTunes and then click the “Tagged” list on the left side of the iTunes software screen. Click the “view” button for purchasing information.Note:1. How to enter the iTunes tagging function? “TAG” and “DIGITAL” light up wh en Tagging function is ready, press [ISR] button on the remote control to start iTunes Tagging.2. What is seen on the radio’s display to let me know I have tagged the tune? Press [ISR] button on the remote control to show “STORED TAG ## OF 64”. After connect to your iPod, the display shows “SENDING TAG ##”. If no connection, the display will show “STORED TAG ## OF 64”. You could save 64 Tag into E2PROM in total. When you connect to your iPod, Tag information will be saved in the iPod, and the data in E2PROM will be cleared.3. Then how do I get the tagged tune from my iPod to the computer? If you have install iTunes, connect your iPod to your computer and buy songs online.](https://usermanual.wiki/Faurecia-Clarion-Electronics/FZ502/User-Guide-1602125-Page-8.png)
![English8FZ502SiriusXM Satallite Radio Operations SiriusXM Satallite Radio OperationsSiriusXM Tuner operation:When a SiriusXM Tuner is connected to this unit, the following operations may performed.Receiving Channels with the SiriusXM TunerAbout SiriusXM Satellite RadioEverything worth listening to is on SiriusXM. get over 130 channels, including the most commercial-free music,plus the best sports,news,talk and entertainment. A SiriusXM Tuner and Subscription are required. For more information,visit www.siriusxm.com.Notes:• The SiriusXM Tuner Satellite Radio controls on this unit are available only when a SiriusXM Tuner is connected.1. Press [SRC / ] button to activate the Satellite Radio(SIRIUSXM) mode.2. Press[ ] or [ ] to select the desires channel. Holding down [ ] or [ ] will rapidly browse through the channels. alternatively,you can enter the number of the desired channel using the numeric keypad on an optional remote control. Checking the SiriusXM Radio ID NumberTo subscribe to the SiriusXM Satellite Radio service,it is necessary to locate and identify the Radio ID of your SiriusXM Tunner. The Radio ID contains 8 characters and can be found on the bottom of your SiriusXM Tunner or can be displayed on when selecting Channel 0 by following the steps below:1. While in the Satellite Radio Mode,press [ ] or [ ] to select channel “0”. The unit displays “RADIO ID” and ID number alternately.Notes:• The Radio ID does not include the letters I,O,S or F.2. To canel the ID number display,select a channel other than “0”.Storing Channel Presets1. Press [BAND] to select the desired band you want to store the preset in. There are 3 Satellite Radio Preset bands. Each press of [BAND] changes the band: SXM1 -> SXM2 -> SXM3 -> SXM12. Tune to the desired channel and then press and hold one of the preset buttons (1 through 6),for at least 2 seconds, to store the channel. The display then shows the stored Band and p r e s e t number (for example, SXM1-3 is shown when preset 3 of band 1 is selected).3. Repeat the procedure to store up to 5 other channels on to the same band.Notes:• A total of 18 channels can be stored in the preset memory, 6 channels for each band (SXM1,SXM2 and SXM3).• If you store a new channel into a preset which the new one.Tuning Channels using Presets1. Press [BAND] to select the desired band of Presets you wish to access.2. Press the preset buttons (1 through 6) that has your desired Satellite Radio channel stored in memory.Category Browsing1. Pre ss [ ] or [ ] in the select the SiriusXM mode to activate the Category Browsing mode.2. Press [ ] or [ ] to select desi red category.3. Rotate the [VOLUME] knob to select to desired channel within the selected Category, and then press [VOLUME] enter.Notes:• If no operation is perfprmed for 10 seconds, the Category Browsing mode is canceled.Tuning Channels using PresetsWhile listening to SiriusXM Satellite Radio, you can be alerted when your favorite songs or artists are playing on other channels. An interruption ALERT will be dispalyed when a matching artist or song is found on another channels. 1. Press and hold FUNC./VIEW for at least 2 seconds when a Song or the song of an Artist you want to store is playing. The [F] indicator lights up.2. Press the 1 (preset) button to store the Artist/Song. A note to memorize the ART(artist name) or the SNG(song title) is displayed.Notes:• If either the artist or song title is not available to save,UNAVAILABL will be displayed.3. Rotate the [VOLUME] knob to choose SAVE ART or SAVE SNG(when available) and then press [VOLUME] knob enter.4. The new alert was stored in memory. An “ART/SONG SAVED” pop-up screen is following by an “XU(sed)/YE(mpty)”. X is the total number of song titles or artist names stored in memory, and Y is the total number of memory locations still available for storage.Notes:• If you try to store when memory is full,“MEM FULL” is displayed followed by “REPLACE/CANCE L”. If you wan t to re place an existing alert item, select “REPLACE” by rotating the [VOLUME] knob, and then press [VOLUME] enter,the existing alert list stored in memory is displayed. Select one of the stored alerts using the [VOLUME] knob.To replace the selected alert,press [VOLUME] knob and an “ART/SONG SAVED” pop-up screen is followed by an “X U(sed)/Y E(mpty)”.• You can manage the stored Alert momory setting on steup mode.• If no operation is perform for 10 seconds, the setting mode is canceled.Receiving and Tuning to an AlertWhenever a stored sports team,artist,or song is playing on another channel,an interruption ALERT appears on the unit display.To tune to game,aitist or song identified by the alert,follow the steps below:1. Rotate the [VOLUME] knob to select the desired game,artist or song from the list of active alerts.2. Press [VOLUME] knob enter.Notes:• If no operationg is performed for 5 seconds,the unit returns to normal mode.• Sports teams/Artist name and Song title which you have stored and which are currently playing will be displayed in s category called “MY GAMES”/“MY MUSIC” in search mode.Search FunctionYou can search for SiriusXM programming content by Category or by Channel.1. Press [VOLUME] knob in the SiriusXM mode.2. Rotate the [VOLUME] knob to select the desired Category/Channel, and then press [VOLUME] knob enter.Notes:• During channel search,pressing [ ] or [ ] to select another Category.Receiving and Tuning to an Alert1. When SiriusXM mode,select your favorite SiriusXM Channel.2. Press and hold [ ] for at leadt 2 seconds. The channel you selected is stored as the jump Source.3. Press and hold [ ] for at least 2 seconds to recall and tune to the saved jump Source channel.Notes:• Pressing and holding [ ] again for at 2 seconds will jump back to the revious mode or SiriusXM channel.Instant Replay FunctionWhen SiriusXM mode,you can pause,rewind anf replay up to 30 minutes of live SiriusXM Satellite Radio.1. While listening to a SiriusXM channel ,press [ ] to enter the Replay mode,which mutes the audio. The display will show“PAUSE” while in this mode.2. Press [ ] again to resume playback of the stored audio from the point at which it was paused. During playback,the SiriusXM Tuner will continue to store the channel audio until you exit thr Instanr Replay mode(up to 30 minutes).During REPLAY playback:• Fast rewind: Press and hold [ ].• Fast forward: Press and hold [ ].• Returning to the beginning of the current song: Press [ ].(If you press [ ] in the rst 2 seconds of a song,you return to the beginning of the previous song.)• Advancing to the beginning of the next song: press [].](https://usermanual.wiki/Faurecia-Clarion-Electronics/FZ502/User-Guide-1602125-Page-9.png)
![English9FZ502Notes:• If you continue to press Fast forward until the end,the Instand Replay mode is canceled, and the unit will change to live SiriusXM radio mode. • If you change channels while in Replay mode,the unit will exit Replay mode to live Satellite Radio mode and clear the Replay memory.Using iTunes taggingiTunes Tagging lets you tag songs you hear on SiriusXM channels with your new CZ702 and then preview, buy, and download then later from your iTunes Tagged playlist the next time you sync your iPod/iPhone.Notes:• For details on the iPod/iPhone modes usable with this unit,refer to “Connecting an iPod/iPhone” on page 9.1. A song may be tagged while listening to a SiriusXM channel if the display shows the “Tag” icon.2. Press and hold Tag for at least 2 seconds while the desired song is playing. The “Tag” blinks at the same time the “TAGGING” is displayed.3. When completed, “TAG STORED” is displayed and the “Tag” indicator lights up.Notes:• During tagging, the iPod/iPhone takes priority to save the tag information.If no iPod/iPhone is connected, the tag information is saved to this unit.• When the memory of iPod/iPhone is full,“iPod FULL” is displayed. The tag informationg will be stored to the unit. • If the tagging operation is interrupted by a source or channel change, the tagging operation will be canceled and the unit may not display “CANNOT TAG”. • This unit can store up to 50 pieces of tag information. When the memory of the unit is full, “MEMO FULL” may be displayed. • When iPod/iPhone that doesn’t support the tagging function is connected, “NON-TAGGING IPOD” may be displayed.• When the iPod/iPhone is disconnected from the unit during tagging, its tag information will be stored in the unit.• If there is stored tag information on the unit, when an iPod/iPhone supporting the tag function is connected, the stored tag information will be transferred to be iPod/iPhone automatically. When the iPod/iPhone memery becomes full, “iPod FULL” will be displayed, and any remaining tag information on the unit will not be transferred to the iPod/iPhone.• If tag information already exists, “ALREAGY TAGGED” will be displayed when you try to tag information again.• Tagging may be canceled by changing th e fre q uency or st ation , and t he message “CANNOT TAG” ,etc, may not be displayed.• If a song is tagged and the remaining storage volume of the connected iPod/iPhone is sufficient to hold the song’s tag information, it will be saved on the iPod/iPhone.• If there is stored tag information on CZ702, when iPod/iPhone models supporting the tag function are connected, the Tag information will be transferred to be the iPod/iPhone with which the USB terminal is activated automatically. When the iPod/iPhone memery becomes full, “iPod FULL” will be displayed,and any remaining tag information on the unit will not be transferred to be iPod/iPhone. Changing the DisplayText information, such as the channel name, artist name/feature and song/program title, is available with each SiriusXM channel. The unit can display this text information as explained below.1. In SiriusXM mode, press VIEW. Each time you press this button, the display changes as shown below. Band/channel Number -> Clock -> Channel Name* -> Artist Name* -> Song Title* -> Content info.* -> Category Name* -> Band/Channel Number* If there is no text information,nothing will be displayed.SiriusXM Satallite Radio Operations1. Move the cover of the USB slot to the left. Insert a USB cable (CCA-755) into the USB slot. Insert a USB device into the USB cable. When connecting a USB device, the unit will read the les automatically.2. To remove the USB device, you should rst select another source or turn off the power, in order to avoid damaging the USB device. Then take off the USB device. Move the cover to the right.USB OperationsCCA-755Folder SelectThis function allows you to select a folder containing MP3/WMA les and start playing from the rst track in the folder.1. Press and hold [CONTROL] knob (up) on the panel. Press and hold [CONTROL] knob (up) on the panel to move the next folder. 2. To select a track, press the [CONTROL] knob (right / left) on the panel or [ , ]button on the remote control.Search Function1. Press the [CONTROL] knob (up) to enter FOLD SCH mode, and press [CONTROL] knob (center) to comfirm, then rotate [CONTROL] knob to select the folder list search mode.2. Rotate the [CONTROL] knob to select a folder.3. Press the [CONTROL] button (center) to enter the file list search mode. And then the track list appears in the display.4. Turn the [CONTROL] knob to select a track.5. Press the [CONTROL] knob (center) to play.* When play back MP3 / WMA file, this function is performed in the current folder.Top functionThe top function resets the USB player to the rst track of the USB device. Press and hold the [ CONTROL ] knob (down) to play the first track (track No. 1) on the USB device.* In case of MP3/WMA, the rst track of the current folder will be played.Pausing play1. Press the [ ] button on the remote control to pause play. “PAUSE” appears in the display.2. To resume MP3/WMA play, press the [ ] button on the remote control again.Selecting a trackTrack-up1. Press the [CONTROL] knob (right) on the panel or [ ] button on the remote control to move to the beginning of the next track.2. Each time you press the [CONTROL] knob (right) on the panel or [ ] button on the remote control, the track advances to the beginning of the next track.Track-down1. Press the [CONTROL] knob (left) on the panel or [ ] button on the remote control to move back to the beginning of the current track.2. Press the [CONTROL] knob (left) on the panel or [ ] button on the remote control twice to move back to the beginning of the previous track.Fast-forward/Fast-reverseFast-forwardPress and hold the [CONTROL] knob (right) on the panel or [ ] button on the remote control.Fast-reversePress and hold the [CONTROL] knob (left) on the panel or [ ] button on the remote control.* For MP3/WMA USB device, it takes some time until the start of searching and between tracks. In addition, some errors may occur in the play time.](https://usermanual.wiki/Faurecia-Clarion-Electronics/FZ502/User-Guide-1602125-Page-10.png)
![English10FZ502USB OperationsOther various play functionsScan playThis function allows you to locate and play the rst 10 seconds of all the tracks recorded on a USB.Press the [ SCN/PS/AS ] button on the remote control to perform scan play.Repeat playThis function allows you to play the current track repeatedly or play a track currently being played in the MP3/WMA folder repeatedly.1. Press the [ RPT ] button on the remote control once or more until “TRK RPT” appears on the display to perform repeat play, and “RPT” segment lights on. 2. For MP3/WMAles,press[ RPT ] button on the remote control repeatedly until “FOLD RPT” appears on the display for folder repeat play.3. Press [ RPT ] button on the remote control repeatedly until “RPT OFF” appears on the display to cancel repeat playback, and “RPT”segmentgoeso.Random playThis function allows you to play all tracks recorded on a USB device in a random order.Press the [ RDM ] button on the remote control to perform random play.iPod & iPhone OperationsConnectConnect your iPod or iPhone to the USB slot via CCA-748 cable.When connecting a device, the unit will read the files automatically. The track information display on the screen once playback start.MENUIn the S-CTRL OFF mode, press the [CONTROL] knob (up), rotate the knob select “MUSIC” or “VIDEO”.Select “MUSIC”, press the [CONTROL] knob, then rotate the [CONTROL] knob to show PLAY LISTS / ARTISTS / ALBUMS / GENRES / SONGS / COMPOSERS, then press the [CONTROL] knob to conrm. Select “VIDEO”, press the [CONTROL] knob, then rotate the [CONTROL] knob to show MOVIES / MUSIC VIDEO / TV SHOWS / VIDEO PODCASTS / RENTALS, then press the [CONTROL] knob to conrm. NOTE:• In case of VIDEO Playback, CCA-748 cable and monitor (sold separately) are required.• VIDEO MENU item is different by the model of connected iPod and language setting.Repeat playThis function allows you to play the current track repeatedly or play all tracks in your iPod/iPhone repeatedly.1. Press the [RPT] button on the remote control once or more until “RPT ON” appears on the LCD to perform repeat play.2. Press [RPT] button on the remote control repeatedly until “RPT OFF” appears on the LCD to cancel repeat playback. MonitorCCA-748iPod & iPhone OperationsRandom playThis function allows you to play all tracks in a random order.1. Press the [RDM] button on the remote control once or more until “RDM ALBUM” appears on the LCD for album random play.2. Press the [RDM] button on the remote control once or more until “RDM SONG” appears on the LCD to perform random play.3. Press the [RDM] button on the remote control once or more until “RDM OFF” appears on the LCD to cancel random playback. Setting iPod simple control modeUse this function if you wish to operate through your iPod connected to this unit via the USB cable.* The factory default setting is “ OFF “.1. Press and hold [CONTROL] knob (center), and rotate the [CONTROL] knob choose ADJUST, then press the [CONTROL] knob (center) to enter system setup. 2 Press the [CONTROL] knob (left / right) to select “ S-CTRL“. 3. Rotate the [CONTROL] knob to select “ ON “ or “ OFF “ . • ON: Operations are made through your iPod. • OFF: Operations cannot be made through your iPod.Notes:• When performing iPod operations using simple control mode, make the operations slowly. If repetitive operations are performed too quickly, unforeseen errors may occur.• When performing iPod operations using simple control mode, please do not operate the iPod and the unit at the same time, otherwise there may be unexpected event happened.• Some iPod models do not support this function. Consult your nearest Clarion dealer or website to conrm which models do not support this function. iPod menu alphabet searchThis function searches the subfolders for desired alphabetical letters.1. Press the [CONTROL] knob (up), and rotate [CONTROL] knob to select the iPod menu mode.2. Rotate the [CONTROL] knob to switch between categories. MUSIC: PLAYLISTS, ARTISTS, ALBUMS, GENRES, SONGS, COMPOSERS VIDEO: MOVIES, MUSIC VIDEOS, TV SHOWS VIDEO PODCASTS, RENTALS3. Press the [CONTROL] knob. (The contents of the category are displayed.)4. Press and hold the [CONTROL] knob (down).5. Rotate the [CONTROL] knob to select the desired letter to search.6. Press the [CONTROL] knob to perform search.Press the [CONTROL] knob on the panel or [SRC/ ] button on the remote control once or more to select “AUX”.AUX is just for audio content with 3.5mm Jack connector plugged into audio-in socket on the front panel on the right of USB slot.AUX Input sensitivity setting1. Press and hold the [CONTROL] knob .2. Turn the [CONTROL] knob to select “AUX SENS”.AUX Operations3. If the output level of connected external audio player is “HIGH”, rotate the [CONTROL] knob and choose “LOW”. And if the output level is “LOW”, choose “HIGH”.](https://usermanual.wiki/Faurecia-Clarion-Electronics/FZ502/User-Guide-1602125-Page-11.png)
![English11FZ502audio data such that it can be processed as a steady and continuous stream. Users can stream music from their external audio player to their car stereo wirelessly and listen to the tracks through the car’s speakers. Please consult your nearest Clarion dealer for more information on the product of wireless audio streaming transmitter offered.CAUTIONPlease avoid operating your connected mobile phone while audio streaming as this may cause noise or sound choppy on the song playback.Audio streaming may or may not resume after tele p h o n e i n t e r r u p t as this i s dependent on mobile phone.System will always return to Radio mode if audio streaming is disconnected.Note:Be sure to read the chapter “Pairing” before proceeding.Play / Pause a track1. Push the [CONTROL] knob (down) to pause audio playback.2. To resume audio playback, push the [CONTROL] knob (down) again.Selecting a trackTrack-up1. Press the [CONTROL] knob (right) to move to the beginning of the next track.2. Each time the [CONTROL] knob (right) is pressed, playback proceeds to another track in the advancing direction.Track-down1. Press the [CONTROL] knob (left) to move to the beginning of the previous track.2. Each time the [CONTROL] knob (left) is pressed, playback proceeds to previous track in the reverse direction.Note:Playing order will depend on Bluetooth audio Bluetooth Operationsplayer. When [CONTROL] knob (left) is pressed, some A2DP devices will restart the current track depends on the duration of playback.During music streaming playback, “A2DP” will be shown on the display. Information about tracks (e.g. the elapsed playtime, songtitle, etc.) cannot be displayed on this unit. When A2DP device is disconnected, “BT DISCONNECT” will be shown on the displayand return to previously selected audio source. Some Bluetooth audio players may not have play / pause synchronized with this unit. Please make sure both device and main unit are in the same play / pause status in BT MUSIC mode.Bluetooth OperationsThe Bluetooth allows you to utilize your car’s built-in audio system for wireless mobile phone or music handsfree communication. Some Bluetooth mobile phones have the audio features, and some portable audio players support Bluetooth feature. This system can play audio data stored in a Bluetooth audio device. The car stereo with Bluetooth will be able to retrieve phonebook contacts, received call, dialed call, missed call, incoming calls, outgoing call and listen to music.Note:• Leaving it exposed to high temperatures or direct sunlight can cause distortion or discoloration which may result in a malfunction.• This system will not operate or may operate improperly with some Bluetooth audio players.• Clarion cannot guarantee the compatibility of all mobile phones together with unit.• Audio playback will be set to the same volume level as set during telephone call. This might cause problems, if extreme volume level is set during telephone call.Handsfree Operations Pairing1. Turn on Bluetooth function of your mobile phone.2. Enter mobile phone’s Bluetooth setup menu.3. Search for new Bluetooth devices.4. Select FZ502 from the pairing list on the mobile phone.5. Ente r “0000” as the password (The password default setting is “ 0000 ”).6. After pairing successfully, the unit will enter Bluetooth mode automatically, and “BLUETOOTH CONNECTED” will appear on the LCD.Making a callOperation from Bluetooth menuPress the [CONTROL] knob to switch the source to “BLUETOOTH”. • Dial NumberPress and hold the [CONTROL] knob (center) choose ADJUST, then rotate the [CONTROL] knob select CALL LST.1. Press the [CONTROL] knob.2. Rotate the [CONTROL] knob on the front panel to switch: DIAL NUMBER / DIALLED CALL / MISSED CALL / RECEIVED CALL / MEMORY PHONEBOOK / SIM PHONEBOOK 3. Press the [CONTROL] knob to conrm the selection, “WAITING” will appear on the LCD.4. Press the [CONTROL] knob to dial.5. Press the [CONTROL] knob (right) to terminate call.• Dialled/Missed/ Received Call HistoryYou can search any Dialled/Missed/Received Call History.1. Rotate the knob to select “DIALED CALL”, “MISSED CALL” or “RECEIVED CALL”.2. Press the knob to enter the selected call history.3. Rotate the [CONTROL] knob to scroll the contacts.4. When the contact name or mobile phone No. is displayed, press the [CONTROL] knob (center) to call the mobile phone No. of that contact. * Press the [CONTROL] knob (right) to end the call.• Call from PhonebookUser can search the contact name in the phonebook and make call.1. Rotate the [CONTROL] knob to select “SIM PHONE BOOK” or “MEMORY PHONE BOOK“ .2. Press the [CONTROL] knob (center) to enter the selected phonebook.3. Rotate the [CONTROL] knob to scroll the contacts.4. When the contact name is displayed, press the [CONTROL] knob (center) to call the mobile phone No. of that contact. * Press the [CONTROL] knob (right) to end the call.• Answering a callYou can answer an incoming call by pressing the [CONTROL] knob.* Press the [CONTROL] knob (right) to reject an incoming call.Audio Streaming OperationsWhat is audio streaming?Audio streaming is a technique for transferring](https://usermanual.wiki/Faurecia-Clarion-Electronics/FZ502/User-Guide-1602125-Page-12.png)
![English12FZ5025. TROUBLE SHOOTINGGENERALProblem Cause MeasureUnit can not power on.Unit fuse blown. Replace with new fuse of correct rating.Car battery fuse blown. Replace with new fuse of correct rating.Unit can not power on.Nothing happens when buttons are pressed.Display is not accurate.The microprocessor has malfunctioned due to noise, etc.Turnothepower.Press the [RESET] button with a thin rod.Note:When the [RESET] buttonispressed,turnothe ACC power.** When the [RESET] button is pressed,frequencies of radio stations, titles, etc. stored in memory are cleared.No/low audio output.Improper audio output connection. Check wiring and correct.Volume set too low. Increase volume level.Speakers damaged. Replace speakers.Heavily biased volume balance. Adjust the channel balance to center position.Speaker wiring is in contact with metal part of car. Insulate all speaker wiring connections.Poor sound quality or distortion.Speaker power rating does not match unit. Replace speakers.Wrong connections. Check wiring and correct.Speaker is shorted. Check wiring and correct.Unit resets itself whenengineiso.Incorrect connection between ACC and Battery. Check wiring and correct.6. ERROR DISPLAYSDisplay Cause MeasureERROR 2 Do not support iPod & iPhone. Change another device.* The head unit will return to RADIO mode.If an error occurs, one of the following displays is displayed. Take the measures described below to solve the problem.If an error display other than the ones described above appears, press the [RESET] button. If the problem persists, turn off the power and consult your store of purchase.* When the [RESET] button is pressed, frequencies of radio stations, titles, etc. stored in memory are cleared.USB DevicesProblem Cause MeasureUSB device cannot be inserted.The USB device has been inserted with wrong direction.Reversing the connection direction of the USB device, try it again.The USB connector is broken. Replace with a new USB device.USB device is not recognized.The USB device is damaged. Disconnect the USB device and reconnect. If the device is still not recognized, try replacing with a different USB device.Connectors are loose.No sound heard with the display “No File” shown.No MP3/WMA le is stored in the USB device. Store these les properly in the USB device.Sound skips or is noisy.MP3/WMA les are not encoded properly. Use MP3/WMA les encoded properly.BluetoothProblem Cause MeasureCannot pair the Bluetooth enabled device with the car audio system.The device does not support the proles required for the system. Use another device to connect.The Bluetooth function of the device is not enabled.Refer to the user manual of the device for how to enable the function.The audio quality is poor after connection with a Bluetooth-enabled device.The internal microphone gain is not set correctly.Adjust the gain of the internal microphone in System Setup.The external microphone is not set correctly nor properly positioned.Adjust the gain and position of the external microphone.For example, stick the microphone onto the dashboard so it is close to the driver.](https://usermanual.wiki/Faurecia-Clarion-Electronics/FZ502/User-Guide-1602125-Page-13.png)
