Fego Precision Co RF136 Oscillating Fan Remote Control User Manual

Download:
Mirror Download [FCC.gov]
Document ID	835381
Application ID	AMBV32hRqErgtcD/uKEXKA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	40.69kB (508569 bits)
Date Submitted	2007-08-29 00:00:00
Date Available	2007-08-29 00:00:00
Creation Date	2007-08-02 15:42:58
Producing Software	Acrobat PDFWriter 5.0Windows NT ª©
Document Lastmod	2007-08-24 11:46:38
Document Title	E:\FILE_SRV3\產品資料\中山宇森\
Document Creator	Adobe PageMaker 6.5C - [E:\FILE_SRV3\產品資料\中山宇森\RF136觸控單燈\RF152-2說明書.p65]
Document Author:	duckss

SMART REMOTE
BLACK (TO MOTOR L) to wire from fan
IMPORTANT: Follow these steps to insure proper
BLUE (FOR LIGHT) to wire from fan.
installation and operation
IMPORTANT SAFETY PRECAUTIONS
Install your ceiling fan by the wiring diagram provided
WARNING: To avoid electrical shock, be sure that
with the fan without the receiver in place.
electricity has been turned off at the circuit breaker or
PREFER: connect the ceiling to a power switch in
Turn on electrical power at the circuit breaker or fuse
fuse box before wiring
the power line to get the flip switch control
box. Turn wall switch‘’ON’’.
ALL wiring must be in accordance with the National
function.
Set your ceiling fan to HIGH speed with its pull chain
Electrical Code and local electrical codes. A qualified
Control. Do not adjust the ceiling fan pull chain after this 3. Complete ceiling fan installation and assembly
electrician should perform electrical installation.
according to its provided instruction.
Step.
IMPORTANT: When the frequency code is
Turn on light kit (if present)
DO NOT use water or detergents to clean the remote
changed a new code needs to be set by sliding
Turn wall switch ‘’OFF ‘’
transmitting unit. A dry dust cloth will be suitable for
the FREOUENCY CODE SWITCH on the receiver.
Turn off electrical power at the circuit breaker or Fuse
most cleaning.
box.
Connecting the Receiver
ONLY the flip switch and transmitter unit should
1. Disconnect the wires from the ceiling to the fan.
change the fan speeds.
Install the receiver to the ceiling fan according to
your mounting type (Figure 1). Be sure the
Do not use the pull chain to change fan speeds after
antenna is positioned so it is exposed when
installation, as damage could result to your remote
canopy is attached. Do not modify or damage the
control or ceiling fan.
antenna wire as control performance may be
reduced.
DO NOT use the reverse switch when the ceiling fan
2. Use the two larger wire nuts supplied to connect
is operating. This could result in damage to your
the receiver and house wiring; then use the three
Remotel control or ceiling fan.
small wire nuts supplied to connect the receiver
and ceiling fan wiring. See Wiring Diagram in
INSTALLATION AND WIRING
Figure 2.
LOW BATTERY
BLACK ‘’AC in L‘’to HOT wire in ceiling
WARNING: To avoid electrical shock, be sure that
WHITE ‘’AC in N‘’to NEUTRAL from ceiling
TRANSMITTER OPERATION
SPEED BOTTON to set the fan speeds.
Ant enna
Light on/off: to toggle set the light on/off.
ACIN_N(WHITE)
Receiver
Dimmer: to set the light power rating. This key function
is only when the light is ON.And keep the light key.
Bracket
POWER RATING:
120V/60Hz
LIGHT: 300W MAX
FAN: 85W (MAX)
ON
SPEED
ACIN_L(BLACK)
SECURITY CODE
SWITCH
NOTICE
THE BATTERY OF THE REMOTE THAT USE THE ALKALINE BATTERY IS BETTER.
General information:
15.203 - The transmitter shall not be collocated
with other transmitters or antennas.
NOTICE
& 2.1093 - To comply with FCC RF
2.1091
exposure
compliance
requirements,
a separa15.21- Any
changes
or modifications
tion
of at
least 20 cm
not distance
expressly
approved
bymust
the be maintained
between
antenna
of thisvoid
device
grantee
of thisthedevice
could
theand
all
persons.
This Transmitter
user's
authority
to operatemust
the not be
collocated or operating in conjunction with any
equipment.
other antenna or transmitter.
ANT ANTENNA
Canopy
Figure1.
electricity has been turned off at the circuit breaker or
fuse box before wiring.
Figure 2.
WHITE (TO MOTOR N) to wire from fan.
PRESET FUNCTION (MEMORY):
If you use the wall switch to turn off the fan, the
speed and lighting level that you previously set will
remain in the remote control’s memory. The next time
electricity is turned on, fan operation will resume at the
same speed and lighting level when you press the FAN
and/or LIGHT key on the remote unit. NOTE For
convenient access and safe keeping of your remote
control unit. Mount near a wall switch by using the
bracket provided.
ON
RF152-2

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-701
Create Date                     : 2007:08:02 15:42:58Z
Creator Tool                    : Adobe PageMaker 6.5C - [E:\FILE_SRV3\產品資料\中山宇森\RF136觸控單燈\RF152-2說明書.p65]
Modify Date                     : 2007:08:24 11:46:38+08:00
Metadata Date                   : 2007:08:24 11:46:38+08:00
Format                          : application/pdf
Creator                         : duckss
Title                           : E:\FILE_SRV3\產品資料\中山宇森\
Producer                        : Acrobat PDFWriter 5.0Windows NT ª©
Document ID                     : uuid:50b3d52d-f086-4a93-9209-f990f6d913de
Instance ID                     : uuid:40210074-adee-4aba-8ead-48c272481099
Has XFA                         : No
Page Count                      : 1
Author                          : duckss

EXIF Metadata provided by EXIF.tools