Feig Electronic MR100-PR100 Passive Tag Reader User Manual Operation Manual
Feig Electronic GmbH Passive Tag Reader Operation Manual
Contents
- 1. Users Manual
- 2. Installation Guide
Users Manual
O B ID i-scan Montageanleitung / Mounting Instruction ID ISC.MR100-A / ID ISC.PR100-A (deutsch / english) M10202-2de-ID-B.DOC DEUTSCH Identifikation System OBID i-scan ENGLISH deutsche Version ab Seite 3 english version from page 19 Seite 2 von 34 FEIG ELECTRONIC GmbH DEUTSCH Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A Ausgabe: cf/01/09/24 - m10202-2de-id-b.doc © Copyright 2001 by FEIG ELECTRONIC GmbH Weitergabe sowie Vervielfältigung dieses Dokuments, Verwertung und Mitteilung ihres Inhalts sind nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlung verpflichtet zu Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder Gebrauchsmuster-Eintragung vorbehalten. Die Angaben in dieser Montageanleitung können ohne vorherige Ankündigung geändert werden. Alle früheren Ausgaben verlieren mit dieser Montageanleitung ihre Gültigkeit. Die Zusammenstellung der Informationen in dieser Montageanleitung erfolgt nach bestem Wissen und Gewissen. FEIG ELECTRONIC GmbH übernimmt keine Gewährleistung für die Richtigkeit und Vollständigkeit der gemachten Angaben. Insbesondere kann FEIG ELECTRONIC GmbH nicht für Folgeschäden aufgrund fehlerhafter oder unvollständiger Angaben haftbar gemacht werden. Die in diesem Handbuch gemachten Installationsempfehlungen gehen von günstigsten Rahmenbedingungen aus. FEIG ELECTRONIC GmbH übernimmt keine Gewähr für die einwandfreie Funktion einer OBID®-Anlage in systemfremden Umgebungen. Da sich Fehler, trotz aller Bemühungen nie vollständig vermeiden lassen, sind wir für Hinweise jederzeit dankbar. FEIG ELECTRONIC GmbH übernimmt keine Gewährleistung dafür, dass die in diesem Dokument enthaltenden Informationen frei von fremden Schutzrechten sind. FEIG ELECTRONIC GmbH erteilt mit diesem Dokument keine Lizenzen auf eigene oder fremde Patente oder andere Schutzrechte. ® OBID ist ein eingetragenes Warenzeichen der FEIG ELECTRONIC GmbH FEIG ELECTRONIC GmbH Seite 3 von 34 DEUTSCH Identifikation System OBID i-scan Funkzulassungen Europa (CE) Die Funkanlage entspricht, bei bestimmungsgemäßer Verwendung den grundlegenden Anforderungen des Artikels 3 und den übrigen einschlägigen Bestimmungen der R&TTE Richtlinie 1999/5/E6 vom März 99. USA (FCC) FCC ID: PJMMR100-PR100 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Unauthorized modifications may void the authority granted under Federal communications Commission Rules permitting the operation of this device. ID ISC.MR100 : Die Zulassung nach FCC 47 CFR CH. I Part 15 gilt im Zusammenhang mit der Antenne ID ISC.ANT340/240A. Seite 4 von 34 FEIG ELECTRONIC GmbH Inhalt 1. Sicherheits- und Warnhinweise ................................................................................ 6 2. Leistungsmerkmale der Reader ................................................................................ 7 2.1 Leistungsmerkmale ........................................................................................................... 7 2.2 Verfügbare Readertypen.................................................................................................... 7 3. Montage und Anschluß .............................................................................................. 8 3.1 Spannungs- und Schnittstellenanschluß X2.................................................................... 8 3.2 Versorgungsspannung ...................................................................................................... 9 3.3 Antennenanschluß X4 (nur ID ISC.MR100)..................................................................... 10 3.4 Asynchrone Schnittstelle ................................................................................................ 11 3.4.1 Schnittstellenkonfiguration mittels Jumper .................................................................. 11 3.4.2 RS232-Schnittstelle .................................................................................................... 12 3.4.3 RS485 Schnittstelle..................................................................................................... 13 3.4.4 Adresseinstellung für Busbetrieb................................................................................. 13 4. Bedien- und Anzeigeelemente................................................................................. 14 4.1 LED.................................................................................................................................... 14 5. Technische Daten..................................................................................................... 15 6. Anhang ...................................................................................................................... 17 6.1 Zubehör ............................................................................................................................ 17 6.1.1 Serielles Datenkabel ID CAB.RS-A ............................................................................. 18 6.1.2 Netzteil ID NET.12VDC............................................................................................... 18 FEIG ELECTRONIC GmbH Seite 5 von 34 DEUTSCH Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A DEUTSCH Identifikation System OBID i-scan 1. Sicherheits- und Warnhinweise Vor Inbetriebnahme unbedingt lesen ! • Das Gerät darf nur für den vom Hersteller vorgesehenen Zweck verwendet werden. • Die Bedienungsanleitung ist zugriffsfähig aufzubewahren und jedem Benutzer auszuhändigen. • Unzulässige Veränderungen und die Verwendung von Ersatzteilen und Zusatzeinrichtungen, die nicht vom Hersteller des Gerätes verkauft oder empfohlen werden, können Brände, elektrische Schläge und Verletzungen verursachen. Solche Maßnahmen führen daher zu einem Ausschluß der Haftung und der Hersteller übernimmt keine Gewährleistung. • Für das Gerät gelten die Gewährleistungsbestimmungen des Herstellers in der zum Zeitpunkt des Kaufs gültigen Fassung. Für eine ungeeignete, falsche manuelle oder automatische Einstellung von Parametern für ein Gerät bzw. ungeeignete Verwendung eines Gerätes wird keine Haftung übernommen. • Reparaturen dürfen nur vom Hersteller durchgeführt werden. • Anschluß-, Inbetriebnahme-, Wartungs-, Messungs- und Einstellungsarbeiten am Gerät dürfen nur von Elektrofachkräften mit einschlägiger Unfallverhütungsausbildung erfolgen. • Vor dem Öffnen des Gerätes ist stets die Versorgungsspannung abzuschalten und durch Nachmessen sicherzustellen, daß das Gerät spannungslos ist. • Das Verlöschen einer Betriebsanzeige ist kein Indikator dafür, daß das Gerät vom Netz getrennt und spannungslos ist. • Alle Arbeiten am Gerät und dessen Aufstellung müssen in Übereinstimmung mit den nationalen Bestimmungen und den örtlichen Vorschriften durchgeführt werden. • Der Benutzer ist dafür verantwortlich, daß das Gerät nach den anerkannten technischen Regeln im Aufstellungsland sowie anderen regionalen gültigen Vorschriften aufgestellt und angeschlossen wird. Dabei sind Kabeldimensionierung, Absicherung, Erdung, Abschaltung, Trennung, Isolationsüberwachung und der Überstromschutz besonders zu berücksichtigen. Seite 6 von 34 FEIG ELECTRONIC GmbH DEUTSCH Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A 2. Leistungsmerkmale der Reader 2.1 Leistungsmerkmale Der Reader ist für das Lesen von passiven Datenträgern, sogenannten „Smart Labels“, mit einer Betriebsfrequenz von 13,56 MHz entwickelt worden. Der ID ISC.MR100 eignet sich für alle Anwendungen, bei denen mittlere Lesereichweiten benötigt werden. Zusätzlich wird noch eine externe Antenne benötigt, die an dem Reader angeschlossen werden muß. Der ID ISC.PR100 eignet sich für alle Anwendungen, bei denen keine großen Lesereichweiten benötigt werden. Der Reader verfügt über eine interne Antenne, so daß keine externe Antenne benötigt wird. Eine Anticollision-Funktion ermöglicht das gleichzeitige Lesen von bis zu 30 Transpondern pro Sekunde. Die Elektronik des Readers ist in einem Kunststoffgehäuse untergebracht, welches die Schutzart IP30 besitzt. Der Reader verfügt über eine asynchrone Schnittstelle, die wahlweise als RS232 oder RS485 konfiguriert werden kann. Durch die Konfigurierbarkeit der Schnittstelle kann der Reader auch am Datenbus mit RS485 Schnittstelle betrieben werden. Die Adresse des Readers kann dabei per Software vorgegeben werden. 2.2 Verfügbare Readertypen Folgende Reader sind z.Z. verfügbar: Readertyp Beschreibung ID ISC.MR100-A Asynchrone Schnittstelle und externe Antenne ID ISC.PR100-A Asynchrone Schnittstelle und interne Antenne FEIG ELECTRONIC GmbH Seite 7 von 34 DEUTSCH Identifikation System OBID i-scan 3. Montage und Anschluß Der Reader ist für die Büroumgebung konzipiert. Es ist eine Wandmontage möglich. Der Wandmontagesatz ist zusätzlich zu bestellen. ( Siehe Anhang: 6.1 Zubehör). 3.1 Spannungs- und Schnittstellenanschluß X2 Zum Anschluß der Spannungsversorgung und der asynchronen Schnittstelle befindet sich auf der Leiterplatte ein 9-poliger D-Subminiatur-Steckverbinder (Buchse). Siehe auch Abbildung 3-1: Leiterplatte mit Jumpern und Anschlußsteckern. X2 Schnittstelle Spgsversorgung n.c. A- B+ n.c. GND n.c. AGND n.c. +12 V DC Tabelle 3-1: Anschlußbelegung des Steckers X2 Für den Reader ist ein serielles Datenkabel mit integriertem Spannungsanschluß erhältlich. (Siehe 6.1 Zubehör und 6.1.1 Serielles Datenkabel ID CAB.RS-A). Feig Artikel Nr. Bezeichnung 1690.000.00.00 ID CAB.RS-A Tabelle 3-2: Serielles Datenkabel Seite 8 von 34 FEIG ELECTRONIC GmbH 3.2 Versorgungsspannung Die Versorgungsspannung von 12 V DC ist an der Klemme X2 der Leiterplatte anzuschließen. Hinweis: Eine Verpolung der Versorgungsspannung kann zur Zerstörung des Gerätes führen. Klemme Kurzzeichen Beschreibung X2 / Pin 9 +12V + 12 V DC – Versorgungsspannung X2 / Pin 7 AGND Ground – Versorgungsspannung Tabelle 3-3: Anschluß der Versorgungsspannung Netzteilempfehlungen : Zur Ausnutzung der vollständigen Leistungsfähigkeit des Reader-Moduls sollte auf eine ausreichend stabilisierte und rauschfreie Spannungsversorgung geachtet werden. Bevorzugt wird ein lineares Netzteil mit 12V DC / 580 mA. Bei der Verwendung eines Schaltnetzteils ist darauf zu achten, daß die interne Schaltfrequenz des Netzteils unterhalb von 300 kHz liegt. (Siehe: 6.1 Zubehör und 6.1.2 Netzteil ID NET.12VDC). Feig Artikel Nr. Bezeichnung 1688.000.00.00 ID NET.12VDC Tabelle 3-4: Empfohlenes Netzteil FEIG ELECTRONIC GmbH Seite 9 von 34 DEUTSCH Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A DEUTSCH Identifikation System OBID i-scan 3.3 Antennenanschluß X4 (nur ID ISC.MR100) Zum Anschluß der externen Antenne befindet sich auf der Leiterplatte eine SMA-Buchse. Das maximale Anzugsdrehmoment der SMA-Buchsen beträgt 0,45 Nm. (Achtung: Höhere Anzugsdrehmomente führen zur Zerstörung des Steckers.) Klemme X4 Beschreibung Anschluß der externen Antenne (Eingangsimpedanz 50Ω ) Tabelle 3-5: Anschluß der externen Antenne Hinweise: • Die Eingangsimpedanz der Antenne ist auf einen Wert von 50 Ω ± (3 Ω ∠ 3°) abzugleichen. • Die optimale Betriebsgüte der Antenne sollte im Bereich QB = 10...20 liegen. Zur Ermittlung der Betriebsgüte muß die Antenne mit einer 50Ω -Quelle, z.B. einem Network Analyzer oder einem Frequenzgenerator, versorgt werden. • Für das Erreichen optimaler Lesereichweiten sollte die Länge der Antennenzuleitungen 3,6 m ± 0,1 m betragen. • Beim Anschluß einer Antenne ist darauf zu achten, daß diese die zulässigen Grenzwerte der nationalen Vorschriften bezüglich Funkanlagen nicht überschreitet. Installation mit FCC Zulassung: In Länden, in denen eine FCC-Zulassung benötigt wird, darf der Reader nur mit den in Tabelle 3-6 aufgeführten Antennen in Betrieb genommen werden. Aufgrund von Änderungen oder Modifizierungen, die nicht ausdrücklich von der zuständigen Zulassungsbehörde genehmigt wurden, kann die Betriebserlaubnis des Anwenders erlöschen. Artikel Nr. Bezeichnung 1663.000.00.00 ID ISC.ANT340/240 Tabelle 3-6: Antennen mit FCC Zulassung Die Anschluß-, Inbetriebnahme-, Wartungs-, Messungs- und Einstellungsarbeiten am Gerät dürfen nur von Elektrofachkräften oder Personen mit äquivalenter Ausbildung erfolgen. Seite 10 von 34 FEIG ELECTRONIC GmbH 3.4 Asynchrone Schnittstelle Die asynchrone Schnittstelle kann wahlweise als RS485 oder RS232 konfiguriert werden. Hinweis: Der gleichzeitige Betrieb von RS232 und RS485 Schnittstelle ist nicht möglich. J72 J21 J74 J77 J73 3.4.1 Schnittstellenkonfiguration mittels Jumper X4 J23 J24 X2 Abbildung 3-1: Leiterplatte mit Jumpern und Anschlußsteckern Über den Jumper J21 kann die asynchrone Schnittstelle als RS232- oder RS485-Schnittstelle konfiguriert werden. Jumper RS232 RS485 J21 1-2 2-3 Tabelle 3-7: Konfiguration RS232/RS485 Schnittstelle FEIG ELECTRONIC GmbH Seite 11 von 34 DEUTSCH Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A DEUTSCH Identifikation System OBID i-scan Im Fall der RS485-Schnittstelle können die eventuell benötigten Abschlußwiderstände mit den Jumpern J73, J74 und J77 zugeschaltet werden. Jumper geschlossen offen J73 Pull-Up an RS485 - B ohne Pull-Up an RS485 - B J74 Pull-Down an RS485 - A ohne Pull-Down an RS485 - A J77 Abschlußwiderstand RS485 - A ⇔ RS485 - B ohne Abschlußwiderstand RS485 - A ⇔ RS485 - B Tabelle 3-8: Konfiguration RS485 Schnittstelle J73 RS485 - B+ J77 RS485 - AJ74 Abbildung 3-2: Jumper der RS485 Schnittstelle 3.4.2 RS232-Schnittstelle Der Anschluß der RS232-Schnittstelle erfolgt über X2. Die Übertragungsparameter können per Softwareprotokoll konfiguriert werden. Anschlußbelegung X2 (RS232-Schnittstelle): Klemme Kurzzeichen Beschreibung TxD RS232 – TxD RxD RS232 – RxD GND RS232 – GND Tabelle 3-9: Anschlußbelegung der RS232 Schnittstelle Seite 12 von 34 FEIG ELECTRONIC GmbH DEUTSCH Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A 3.4.3 RS485 Schnittstelle Der Anschluß der RS485-Schnittstelle erfolgt über X2. Die Übertragungsparameter können per Softwareprotokoll konfiguriert werden. Anschlußbelegung X2 (RS485-Schnittstelle): Pin Kurzzeichen Beschreibung A- RS485 – (A -) B+ RS485 – (B +) GND RS485 – GND Tabelle 3-10: Anschlußbelegung der RS485 Schnittstelle 3.4.4 Adresseinstellung für Busbetrieb Für den Busbetrieb bietet der Reader die Möglichkeit die benötigte Busadresse per Software zu vergeben. Die Adressvergabe erfolgt über den Host-Rechner. Mit Hilfe der Software können dem Reader die Adressen "0" bis "254" zugewiesen werden. Hinweis: Da alle Reader werksseitig die Adresse 0 eingestellt haben, müssen sie nacheinander angeschlossen und konfiguriert werden. FEIG ELECTRONIC GmbH Seite 13 von 34 DEUTSCH Identifikation System OBID i-scan 4. Bedien- und Anzeigeelemente 4.1 LED Die LED des Readers kann per Software konfiguriert werden. Tabelle 4.1-1 zeigt die Standard-Konfiguration der LED. Kurzzeichen LED grün LED rot Beschreibung "RUN " Signalisiert den ordnungsgemäßen Ablauf der internen Reader-Software. Leuchet, wenn der Reader betriebsbereit ist. „LABEL“ LED orange Leuchtet, wenn ein Label erkannt wird. „INITIALISIERUNG“ Blinkt während der Reader-Initialisierung nach dem Einschalten. Tabelle 4.1-1: Standard-Konfiguration der LED Seite 14 von 34 FEIG ELECTRONIC GmbH DEUTSCH Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A 5. Technische Daten Mechanische Daten • Gehäuse Kunststoff ABS geschlossen • Abmessungen ( B x H x T ) 85 x 145 x 31 mm • Gewicht 200 g • Schutzart IP 30 • Farbe RAL 9018 Elektrische Daten • Spannungsversorgung typisch 12 V DC max. Spannungsbereich 12 – 24 V DC ± 15 % • Leistungsaufnahme ID ISC.MR100: max. 8 VA ID ISC.PR100: max. 5 VA • Betriebsfrequenz 13,56 MHz • Sendeleistung ID ISC.MR100: 1,0 W ID ISC.PR100: 0,5 W • Antennenanschluß (nur ID ISC.MR100) SMA Buchse (50Ω ) • Schnittstellen RS232 und RS485 (wahlweise einstellbar) Funktionelle Eigenschaften • Unterstützte Transponder I• Code• 1, Tag-it-HF, ISO 15693 • Adreßeinstellung für Schnittstelle Software (bis zu 254 Adressen) • Signalgeber optisch 1 LED ( mehrfarbig – rot / grün) FEIG ELECTRONIC GmbH Seite 15 von 34 DEUTSCH Identifikation System OBID i-scan Umgebungsbedingungen • Temperaturbereich - Betrieb - Lagerung -25°C bis +60°C -25°C bis +70°C Angewendete Normen • Zulassung Funk - Europa - USA EN 300 330 FCC 47 CFR Part 15 • EMV EN 300 683 • Sicherheit - Europa EN 60950 Seite 16 von 34 FEIG ELECTRONIC GmbH DEUTSCH Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A 6. Anhang 6.1 Zubehör Zu dem Reader ist folgendes Zubehör zu erhalten. Artikel Nr. Bezeichnung Beschreibung 1688.000.00.00 ID NET.12VDC 12 V DC Netzteil mit passendem Stecker für ID CAB.RS-A. 1690.000.00.00 ID CAB.RS-A Serielles Datenkabel mit integrierter Versorgungsleitung 1691.000.00.00 ID ISC.MS.MR/PR-A 1687.000.00.00 ID CO.RS232/485 1663.000.00.00 ID ISC.ANT340/240 Externe Antenne Abm.: 340mm x 240mm x 9mm Schutzart.: IP30 1451.000.00.01 ID ISC.ANT300/300 Externe Antenne Abm.: 300mm x 300mm x 30mm Schutzart.: IP65 FEIG ELECTRONIC GmbH Wandmontagesatz für ID ISC.MR100 und ID ISC.PR100. Externer RS232/RS485 Umsetzer Seite 17 von 34 DEUTSCH Identifikation System OBID i-scan 6.1.1 Serielles Datenkabel ID CAB.RS-A PC: 9-pol D-Sub Buchse Versorgung: DC-Kupplung 2,5mm*5,5mm Reader: 9pol. D-Sub Stecker Abbildung 6-1: Serielles Datenkabel mit Spannungsanschluß + 12 V DC AGND Abbildung 6-2: Belegung der DC-Kupplung 6.1.2 Netzteil ID NET.12VDC Bei dem Netzteil muß noch der Kupplungsteil mit der korrekten Polarität auf das Netzteil gesteckt werden. Achtung: Der Kupplungsteil ist nicht mehr abtrennbar, wenn er einmal eingerastet ist ! Eine Verpolung kann zur Zerstörung des Gerätes führen. minus - außen AGND plus - innen +12 V DC Abbildung 6-3: Polarität der Kupplung Seite 18 von 34 FEIG ELECTRONIC GmbH ENGLISH Mounting Instruction ID ISC.MR100-A _________ Edition: cf/01/09/24 - m10202-2de-id-b.doc © Copyright 2001 by FEIG ELECTRONIC GmbH Copying of this document, and giving it to others and the use or communication of the contents thereof are forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design. Indications made in this manual may be changed without previous notice. With the edition of this manual, all previous editions become void. Composition of the information in this manual has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips. The installation instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC GmbH does not give any guarantee promise for perfect function of an OBID®-system in cross surroundings. FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this manual and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does not convey any license under its patent rights nor the rights of others. OBID® is a registered trademark of FEIG ELECTRONIC GmbH. FEIG ELECTRONIC GmbH Page 19 of 34 Identifikation System OBID i-scan Type approval ENGLISH Europe (CE) When used according to regulation, this radio equipment conforms with the basic requirements of Article 3 and the other relevant provisions of the R&TTE Guideline 1999/E6 dated March 99. USA (FCC) FCC ID: PJMMR100-PR100 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Unauthorized modifications may void the authority granted under Federal communications Commission Rules permitting the operation of this device. ID ISC.MR100: Approval per FCC 47 CFR CH. I Part 15 applies to use with the antenna ID ISC.ANT340/240. Page 20 of 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A 1. Safety Instructions / Warning .................................................................................. 22 Performance Features of the Reader...................................................................... 23 2.1 Performance features ...................................................................................................... 23 2.2 Available Reader-Types ................................................................................................... 23 Assembly and Wiring ............................................................................................... 24 3.1 Power and interface terminal X2..................................................................................... 24 3.2 Supply voltage.................................................................................................................. 25 3.3 Antenna terminal X4 (only ID ISC.MR100) ...................................................................... 26 3.4 Asynchronous interface .................................................................................................. 27 3.4.1 Interface configuration using jumpers ......................................................................... 27 3.4.2 RS232 interface .......................................................................................................... 28 3.4.3 RS485 interface .......................................................................................................... 29 3.4.4 Setting the address for bus mode ............................................................................... 29 Control and Display Elements................................................................................. 30 4.1 LED.................................................................................................................................... 30 Technical Data .......................................................................................................... 31 Appendix ................................................................................................................... 33 6.1 Accessories...................................................................................................................... 33 6.1.1 Serial data cable ID CAB.RS-A ................................................................................... 34 6.1.2 Power supply ID NET.12VDC ..................................................................................... 34 FEIG ELECTRONIC GmbH Page 21 of 34 ENGLISH Contents Identifikation System OBID i-scan 1. Safety Instructions / Warning ENGLISH Please read before startup ! • The device may be used only for the purpose intended by the manufacturer. • The Mounting Instruction should be kept in an accessible location and handed out to every user and maintenance person. • Non-approved modifications and the use of replacement parts and accessories which have not been purchased or recommended by the manufacturer of the device may cause fires, electrical shocks and injury. This will furthermore result in exclusion of liability and loss of warranty on the part of the manufacturer. • The warranty conditions in effect at the time of purchase shall be considered valid. No liability is assumed for inappropriate, improper manual or automatic setting of parameters for a device or for improper use of a device. • Repairs are to be performed only by the manufacturer. • Hookup, startup, maintenance, measuring and calibration work on the device must be performed only by electrical specialists who have received the relevant accident prevention training. • Before opening the device always turn off the supply voltage and use a test instrument to verify that the device is unpowered. • The fact that the indicator lamp is off does not necessarily mean that the device has been disconnected from the power supply or that it is without power. • All work on the device including installation must be in conformance with national electrical regulations as well as with local code. • The user has to make sure that the appliance is installed and operated according to the technical rules of the country of installation as well as other regional regulations. Cable dimensions, protection, earthing, disconnection, insulation control and excess current protection should be especially considered. Page 22 of 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A 2 Performance Features of the Reader The Reader is designed for reading passive data carriers, so-called „Smart Labels“ at an operating frequency of 13.56 MHz. The reader ID ISC.MR100 is suitable for all applications in which moderate reading distances are required. Also required is an external antenna connected to the Reader. The ID ISC.PR100 is suitable for all applications which don’t require wide reader ranges. The reader contains of an internal antenna, so that is no external antenna necessary. An anti-collision function enables simultaneous reading of up to 30 transponders per second. The Reader electronics is contained in a plastic housing having an IP30 enclosure rating. The Reader comes with an asynchronous port which can be configured for RS232 or RS485. The ability to configure the port means that the Reader can also be operated on a databus with RS485 interface. The address of the Reader is configured via software. 2.2 Available Reader-Types Following Reader-Types are available at present: Reader-Types Description ID ISC.MR100-A asynchronous interface and external antenna ID ISC.PR100-A asynchronous interface and internal antenna FEIG ELECTRONIC GmbH Page 23 of 34 ENGLISH 2.1 Performance features Identifikation System OBID i-scan 3 Assembly and Wiring ENGLISH The Reader is designed for an office environment. It can be wall-mounted, in this case the wallmount kit should be ordered separately. ( see Appendix: 6.1Accessories). 3.1 Power and interface terminal X2 A 9-pin D-sub female socket is located on the circuit board for connecting the supply voltage and asynchronous interface. See also Fig. 3-1: Circuit board with jumpers and sockets. X2 Interface Supply voltage n.c. A- B+ n.c. GND n.c. AGND n.c. +12 V DC Table 3-1: Pin configuration X2 A serial data cable with integrated power connection is available for the Reader. (see 6.1 Accessories and 6.1.1 Serial data cable ID CAB.RS-A). Feig Article No. Part No. 1690.000.00.00 ID CAB.RS-A Table 3-2: Serial data cable Page 24 of 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A 3.2 Supply voltage Connect the 12 V DC supply voltage to terminal X2 on the circuit board. Note: Terminal Name X2 / Pin 9 +12V + 12 V DC – supply voltage X2 / Pin 7 AGND Ground – supply voltage ENGLISH Reversing the polarity of the supply voltage may destroy the device. Description Table 3-3: Connecting the supply voltage Power supply recommendations : To take full advantage of the Reader module performance, you must use a sufficiently regulated and noise-free power supply. Preferred is a linear power supply with 12V DC / 580 mA. When using a switching power supply, be sure that its internal switching frequency is less than 300 kHz. (see: 6.1 Accessories and 6.1.2 Power supply ID NET.12VDC). Feig Article No. Part No. 1688.000.00.00 ID NET.12VDC Table 3-4: Recommended power supply FEIG ELECTRONIC GmbH Page 25 of 34 Identifikation System OBID i-scan 3.3 Antenna terminal X4 (only ID ISC.MR100) An SMA socket is provided on the circuit board for connecting the external antenna. The maximum tightening torque for the SMA socket is 0.45 Nm. ENGLISH (Caution: Higher tightening torque will damage the connector.) Terminal X4 Description Connecting the external antenna (input impedance 50Ω ) Table 3-5: Connecting the external antenna Note: • The input impedance for the antenna should be calibrated to a value of 50 Ω ± (3 Ω ∠ 3°). • The optimum operating Q factor of the antenna should be in a range of Qoper = 10...20. To determine the operating Q the antenna must be supplied with a 50 Ohm source such as a network analyzer or frequency generator. • To achieve optimum read distances, the length of the antenna lines should not exceed 3.6 m ± 0.1 m. • When connecting an antenna, ensure that it does not exceed the permissible limits prescribed by the national regulations for radio frequency devices. Installation with FCC Approval: In countries where FCC approval is required, the ID ISC.MR100 Reader may only be operated using the antennas listed in Table 3-6. Changes or modifications not expressly authorized by the relevant approval body may result in revocation of the user’s operating permission. Article No. Part No. 1663.000.00.00 ID ISC.ANT340/240 Table 3-6: Antennas with FCC Approval Electrical connection, commissioning, maintenance, measurement and calibration work on the unit is to be performed only by electrical specialists or persons with equivalent training. Page 26 of 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A 3.4 Asynchronous interface The asynchronous interface can be configured as either RS232 or RS485. ENGLISH Note: It is not possible to run both RS232 and RS485 at the same time. J72 J21 J74 J77 J73 3.4.1 Interface configuration using jumpers X4 J23 J24 X2 Fig. 3-1: Circuit board with jumpers and sockets Jumper J21 is used to configure the asynchronous interface as RS232 or RS485. Jumper RS232 RS485 J21 1-2 2-3 Table 3-7: Configuring as RS232/RS485 FEIG ELECTRONIC GmbH Page 27 of 34 Identifikation System OBID i-scan ENGLISH In the case of the RS485 configuration, the termination resistors which may be required can be inserted using jumpers J73, J74 and J77. Jumper in out J73 Pull-Up on RS485 - B out Pull-Up on RS485 - B J74 Pull-Down on RS485 - A out Pull-Down on RS485 - A J77 Termination resistor RS485 - A ⇔ RS485 - B no termination resistor RS485 - A ⇔ RS485 - B Table 3-8: Configuring the RS485 interface J73 RS485 - B+ J77 RS485 - AJ74 Fig. 3-2: Jumper of the RS485 interface 3.4.2 RS232 interface The RS232 interface is connected through X2. The transmission parameters can be configured using software protocol. Pin assignments X2 (RS232 interface): Terminal Abbrev. Description TxD RS232 – TxD RxD RS232 – RxD GND RS232 – GND Table 3-9: Wiring assignments for the RS232 Page 28 of 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A 3.4.3 RS485 interface The RS485 interface is connected through X2. ENGLISH The transmission parameters can be configured using software protocol. Pin assignments X2 (RS485 interface): Pin Abbrev. Description A- RS485 – (A -) B+ RS485 – (B +) GND RS485 – GND Table 3-10: Wiring assignments for the RS485 interface 3.4.4 Setting the address for bus mode For bus operation the Reader can be assigned a bus address using software. Addresses are assigned by the host computer. Using the software, addresses “0” to “254” can be assigned to the Reader. Note: Since all Readers are factory set with Address 0, you must connect and configure them one after the other. FEIG ELECTRONIC GmbH Page 29 of 34 Identifikation System OBID i-scan 4 Control and Display Elements ENGLISH 4.1 LED The Reader’s LED can be configured through software. Table 4.1-1 shows the standard configuration of the LED. Abbreviation LED green LED red Description "RUN " Indicates the Reader software is running properly. Turns on when the Reader is ready. „LABEL“ LED orange Turns on when a label is detected. „INITIALIZING“ Flashes during Reader initialization after power-up. Table 4.1-1: Standard configuration of the LEDs Page 30 of 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A 5 Technical Data Mechanical Data ABS plastic ENGLISH • Housing Enclosed • Dimensions (W x H x D) 85 x 145 x 31 mm • Weight 200 g • Enclosure rating IP 30 • Color RAL 9018 Electrical Data • Supply voltage typical. 12 V DC max. voltage range 12 – 24 V DC ± 15 % • Power consumption ID ISC.MR100: ID ISC.PR100: • Operating frequency 13.56 MHz • Transmitting power ID ISC.MR100: ID ISC.PR100: • Antenna connection (only ID ISC.MR100) SMA female (50Ω ) • Interfaces RS232 and RS485 (configurable) max. 8 VA max. 5 VA 1,0 W 0,5 W Functional properties • Supported transponders I• Code• 1, Tag-it-HF, ISO 15693 • Address setting for interface Software (up to 254 addresses) • Visual indicators 1 LED ( multicolor – red / green) FEIG ELECTRONIC GmbH Page 31 of 34 Identifikation System OBID i-scan ENGLISH Ambient conditions • Temperature range - Operation - Storage -25°C to +60°C -25°C to +70°C Applicable Norms • Radio approval - Europe - USA EN 300 330 FCC 47 CFR Part 15 • EMC EN 300 683 • Safety - Europe EN 60950 Page 32 of 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A 6 Appendix ENGLISH 6.1 Accessories The following accessories are available for the Reader. Article No. Part No. 1688.000.00.00 ID NET.12VDC 12 V DC power supply with suitable connector for ID CAB.RS-A 1690.000.00.00 ID CAB.RS-A Serial data cable with integrated supply voltage line 1691.000.00.00 ID ISC.MS.MR/PR-A 1687.000.00.00 ID CO.RS232/485 1663.000.00.00 ID ISC.ANT340/240 External antenna Dimensions: 340mm x 240mm x 9mm Enclosure rating.: IP30 1451.000.00.01 ID ISC.ANT300/300 External antenna Dimensions: 300mm x 300mm x 30mm Enclosure rating.: IP65 FEIG ELECTRONIC GmbH Description Wall mounting kit for ID ISC.MR100. and ID ISC.PR100. External RS232/RS485 converter Page 33 of 34 Identifikation System OBID i-scan 6.1.1 Serial data cable ID CAB.RS-A ENGLISH PC: 9-pin D-sub female Supply: DC adapter 2.5mm*5.5mm Reader: 9-pin D-sub male Fig. 6-1: Serial data cable with supply voltage connection + 12 V DC AGND Fig. 6-2: DC adapter configuration 6.1.2 Power supply ID NET.12VDC The AC adapter must be plugged into the power supply while observing the correct polarity. Caution: The AC adapter can no longer be unplugged once it has been inserted ! Reversing the polarity may destroy the device. minus - outside AGND plus - inside +12 V DC Fig. 6-3: Polarity of the adapter Page 34 of 34 FEIG ELECTRONIC GmbH
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 34 Creator : FinePrint Create Date : 2001:09:28 10:11:25 Title : Operation Manual Author : Fiedler Producer : Acrobat PDFWriter 3.02 für Windows NT Subject :EXIF Metadata provided by EXIF.tools