Feig Electronic TSTPDFSASK Wireless Safety System for industrial doors User Manual PD FSAS 250 Eng 120102
Feig Electronic GmbH Wireless Safety System for industrial doors PD FSAS 250 Eng 120102
UserManual.pdf
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1808551 |
| Application ID | qCffqG9rsQUB19awu7WGzg== |
| Document Description | UserManual.pdf |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 22.99kB (287406 bits) |
| Date Submitted | 2012-10-05 00:00:00 |
| Date Available | 2012-10-05 00:00:00 |
| Creation Date | 2012-10-02 08:30:34 |
| Producing Software | Acrobat Distiller 6.0.1 (Windows) |
| Document Lastmod | 2012-10-02 12:57:33 |
| Document Title | Microsoft Word - PD_FSAS-250 _Eng_120102.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | heinze |
TST PD_FSAS 250 KBit Multiturn Absolute Encoder w/ integrated Wireless Safety System for industrial doors – Stationary Unit ‐ The assembling tolerance from shaft center to sensor center is maximum +/‐1 mm (+/‐ 0.039 inch). Torque for M3 screw / magnet holder fixing : maximum 0.4 Nm 2. Connection image inside with: Mounting and Startup manual ! ATTENTION The content of the door controller manual and particularly the safety instructions must get note! 2.1 battery change: Disconnecting the battery effects clearing of position values from the encoder! After reconnecting the battery a RESET must be done. Do not short or charge the battery. Do not store or operate the system above the specified temperature range. Connecting the encoder with switched on supply voltage is not allowed. 1. Pin connections: ) To do an Reset you must make an short cut between the Reset pins X3‐2 and X3‐1 for a short moment 3. Mounting of encoder: TST PD_FSAS 250 KBit Remarks: - For connection shielded cables with M12 A‐encoded plug are recommended. The shield has to be connected to earth ground only on the controller side. - The housing of the plug is not allowed to be connected to earth ground. - Not used wires must be isolated inside of FU3P FEIG ELECTRONIC GmbH Lange Str. 4 D‐35781 Weilburg, Germany Tel.: +49 (0) 6471 / 3109‐0 Fax: +49 (0) 6471 / 3109‐99 www.feig.de Email: info@feig.de PD_FSAS‐250 _Eng_120102.Doc 4. Mounting of the stationary Antenna: Side view 6. Connection data: Supply voltage +24 V +/‐10%, typical 50 mA. Serial bidirectional Interface RS485 / 19,2k Baud Digital outputs: Three configurable outputs with the following standard setting: Output 1 and 2: Safety output (N.O.) with 8.2kΩ terminal resistor and testing of terminal resistor. Output 3: Breakaway output (N.C. contact at 24V with 560Ω limiting resistor) Connecting to A‐encoded M12 plug with 35cm long cable. Front view Antenna Antenna Technical Data: The max. allowed Length of the customer mounted cable is 50m Radio : Temperature range: Mobile unit Mobile unit Figure: Mounting of Antenna on door Stationary Antenna + aluminum mounting bracket: 44 15 7,6 39 10 24,5 45 5. Figure: Stationary Antenna + aluminum mounting bracket Operating range 2400 to 2483.5MHz 40 channels, Rated output power 0dBm Operating range –40 to +70°C, Storage range –40 to +70°C (recommended +20°C) Protection class: IP65 Max. tolerable speed: 6000 U/min Resolution: 13 Bit / turn (8192 Increments / turn) Counter of turns: 15 Bit Weight: Without cable but with magnet holder 220g Lifetime of battery: typical 10 years Dimensions (L x B x H): Encoder 92 x 69.5 x 24mm Antenna board 84 x 39 x 7.6mm (Antenna height 26mm) 7. FCC Statements: Notice: This device complies with Part 15 of the FCC Rules and with RSS‐210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice: Changes or modifications made to this equipment not expressly approved by FEIG ELECTRONIC may void the FCC authorization to operate this equipment. Notice: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : ‐ Reorient or relocate the receiving antenna ‐ Increase the separation between the equipment and receiver ‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected ‐ Consult the dealer or an experienced radio / TV technician for help FEIG ELECTRONIC GmbH Lange Str. 4 D‐35781 Weilburg, Germany Tel.: +49 (0) 6471 / 3109‐0 Fax: +49 (0) 6471 / 3109‐99 www.feig.de Email: info@feig.de PD_FSAS‐250 _Eng_120102.Doc
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Author : heinze Create Date : 2012:10:02 08:30:34+02:00 Modify Date : 2012:10:02 12:57:33+02:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Producer : Acrobat Distiller 6.0.1 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2012:10:02 12:57:33+02:00 Document ID : uuid:a9db67f5-7cb9-4bec-8d41-ea734213ba73 Instance ID : uuid:52a0dbd3-49f9-48d6-839c-0e6f5394a405 Format : application/pdf Title : Microsoft Word - PD_FSAS-250 _Eng_120102.doc Creator : heinze Page Count : 2EXIF Metadata provided by EXIF.tools