Fibar Group HC2 Home Center User Manual kartka pl
Fibar Group S.A. Home Center kartka pl
User Manual_20131223_v1 - HC-Manual-USA
To start using Fibaro System Home Center 2, please connect the device to power
and LAN sockets, as shown below.
1. Unscrew left side panel
3. Connect wires as shown on gure below
2. Take side panel o
HC2 back HC2 front
WARNING! Do not turn Home Center 2
on without RECOVERY pendrive.
POWER
- click to turn HC2 ON
- click (when HC2 ON) to reset the device
- press and hold for approx 10 seconds to
turn HC2 OFF
LED Indicators Back panel buttons
POWER - power ON
LAN - HC2 connected to Ethernet
INTERNET - HC2 connected to Internet
Z-WAVE - communication within Z-Wave network
LEARN MODE [blinking slowly] - new device
beeing added to the Z-Wave network
LEARN MODE [blinking] - device beeing deleted
from the Z-Wave network
LEARN MODE [blinking quickly] - device has been
added/removed.
RECOVERY - Recovery Mode active
UPDATE - New software version available for
downlowad
SERVICE - Software update in progress.
RECOVERY
- to enter Recovery Mode disconnect the
power supply. Press and hold Recovery
button when reconnecting the power
supply (release the button after entering
Recovery Mode)*.
- click once - entering Learn Mode (add
new Z-Wave device),
- click twice - entering Learn Mode (delete
Z-Wave device),
- press and hold to set static IP:
192.168.81.1*
* NOTE: after setting static IP Home Center
2 will loose the router connection.
For more information go to www.baro.com
Start HC2 with a POWER button and wait approx. 2
minutes for the device to start. Correct connection
will be signalled by diodes 1, 2, 3 (see the glossary
below).
Connect power cable to the mains, and network cable to
LAN socket in your router (Home Center 2 requires an
outside router).
5. Start Home Center 2
4. Connect HC2
Start the HC2 Finder and click "Refresh". After the list
of Home Center 2, available within your local network
appears, choose the one you wish to connect and
click "connect".
After successful connection you will access HC2
control panel. Choose your language version, enter
user name and password. Defaults are: admin /
admin.
Go to www.baro.com, nd
Support section, download
and install HC2 Finder desig-
nated for your operating
system.
6. Login to Home Center 2
POWER
FCC ID: 2AA9MHC2
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHOR-
IZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This
device may not cause harmful interference, and 2.This device must accept any interference received, including
interference that may cause undesired operation. This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.