Fieldpiece Instruments 001 Wireless Module User Manual

Fieldpiece Instruments, Inc. Wireless Module Users Manual

Users Manual

2ALHR001ModuleUser'sManual1. Features‐ On‐chiplowpowermicrocontroller‐ 128KBofIn‐systemprogrammableflash‐ 8KBSRAM‐ OnboardcrystalandPCBAntenna2. Application‐ Wirelessdatacommunication3. PindefinitionPinNo.DescriptionPinTypeFunctions1BLE_RXDigitalI/OUARTRX2BLE_TXDigitalI/OUARTTX3WAKE_UPOutputDigitalI/O4STATUSInputDigitalI/O5GNDDigitalI/OGND6V+DigitalI/OVDD7BLE_ENDigitalI/OVDDEnable4. Howtouse:‐ BeforesendinganyUARTCommand,"WAKE_UP10"mustbedonebyexternalMCU.‐ IftheCC2640moduleisconnectedtoSmartDevices(Android/iOS),thepinSTATUSwillbelogic"1"toinformexternalMCU.
‐ Beacon1. SendCommand'D'/'P'tosendlivemeasureddatafromexternalthroughBeacon.2. Thisisdefaultmode,and2ALHR002modulesenddataonly.Cannotreceiveanydata.‐ BLE1. SendCommand'M'toswitchmodefromBeacontoBLE.2. Afterthemodeswitchsuccessfully,theexternalMCUcanreceivedatafromSmartphone.‐ Receiver1. SendCommand'A'/'B'toswitchmodefromBeacontoReceiver.2. OnlyspecificBeacondatacanbereceived,andtheexternalMCUreceivesthedatafromUART5. Protocol:‐ UARTBaudRate:115200,8,N,1‐ Commands'D':SendMeasuredDataExternalMCUVEABT002ModuleStarterLenOPBattery DataCKEnd#D(0D0A)hExternalMCUVEABT002ModuleStarterLenOPIndiCKEnd>D (0D0A)h'P':SendProductInformationExternalMCUVEABT002ModuleStarterLenOPFPProd.S/NCal.DateCKEnd#P(0D0A)hExternalMCUVEABT002Module
StarterLenOPIndiCKEnd>P (0D0A)h'M':ModeSwitchExternalMCUVEABT002ModuleStarterLenOPS/NCKEnd#M (0D0A)hExternalMCUVEABT002ModuleStarterLenOPIndiCKEnd>M (0D0A)h'A':ScanProductInformationExternalMCU2ALHR001ModuleStarterLenOPCKEnd'#''A' (0D0A)hExternalMCU2ALHR001ModuleStarterLenOPSNAPOBattRSSICKEnd'>''A'     (0D0A)h'B':ScanMeasuredDataExternalMCU2ALHR001ModuleStarterLenOPSNCKEnd'#''B'  (0D0A)hExternalMCU2ALHR001ModuleStarterLenOPAPOBattDataRSSICKEnd'>''B'     (0D0A)hThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept  any  interference  received,  including  interference  that  may  cause undesired operation. Federal Communication Commission Interference Statement  This equipment has been tested and found to comply with the limits for a Class B  digital  device,  pursuant  to  Part  15  of  the  FCC  Rules.  These  limits  are designed  to  provide  reasonable  protection  against  harmful  interference  in  a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference  to  radio  communications.  However,  there  is  no  guarantee  that interference  will  not  occur  in  a  particular  installation.  If  this  equipment  does cause  harmful  interference  to  radio  or  television  reception,  which  can  be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help.  FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's  authority  to  operate  this  equipment.  (Example  -  use  only  shielded interface cables when connecting to computer or peripheral devices).  End Product Labeling      This transmitter module is authorized only for use in devices. The  final  end  product  must  be  labeled  in  visible  area  with  the  following:   “Contains FCC ID:2ALHR001”  ” End Product Manual Information      The  user  manual  for  end  users  must  include  the  following  information  in  a prominent  location  “IMPORTANT  NOTE:  To  comply  with  FCC  RF  exposure compliance requirements. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions    (1) This device may not cause harmful interference and      (2) This device must accept any interference received, including interference that may cause undesired operation.  IMPORTANT NOTE:   In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization.   This device is intended only for OEM integrators under the following conditions:   As long as a condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end product for any    additional compliance requirements required with this module installed    (for example, digital device emissions, PC peripheral requirements, etc.). inconjunctionwithanyotherantennaortransmitter.

Navigation menu