Fieldpiece Instruments 001 Wireless Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3417508
Application ID	82mTMm6KQ7tJdhXytfRJUA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18kB (225025 bits)
Date Submitted	2017-06-07 00:00:00
Date Available	2017-06-07 00:00:00
Creation Date	2017-05-22 13:45:06
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2017-05-22 13:45:06
Document Title	Microsoft Word - 2ALHR001 Module User's Manual.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	PCUser

2ALHR001 Module User's Manual
1. Features
‐ On‐chip low power microcontroller
‐ 128KB of In‐system programmable flash
‐ 8KB SRAM
‐ On board crystal and PCB Antenna
2. Application
‐ Wireless data communication
3. Pin definition
Pin No.
Description
Pin Type
Functions
BLE_RX
Digital I/O
UART RX
BLE_TX
Digital I/O
UART TX
WAKE_UP
Output
Digital I/O
STATUS
Input
Digital I/O
GND
Digital I/O
GND
V+
Digital I/O
VDD
BLE_EN
Digital I/O
VDD Enable
4. How to use:
‐ Before sending any UART Command, "WAKE_UP 1  0" must be done by
external MCU.
‐ If the CC2640 module is connected to Smart Devices (Android/ iOS), the pin
STATUS will be logic "1" to inform external MCU.
‐
Beacon
‐
1. Send Command 'D'/'P' to send live measured data from external through
Beacon.
2. This is default mode, and 2ALHR002 module send data only. Cannot
receive any data.
BLE
‐
1. Send Command 'M' to switch mode from Beacon to BLE.
2. After the mode switch successfully, the external MCU can receive data
from Smart phone.
Receiver
1. Send Command 'A'/'B' to switch mode from Beacon to Receiver.
2. Only specific Beacon data can be received, and the external MCU receives
the data from UART
5. Protocol:
‐ UART Baud Rate: 115200, 8, N, 1
‐ Commands
'D': Send Measured Data
External MCU  VEABT002 Module
Starter
Len
OP
Battery
Data
CK
End
(0D 0A)h
External MCU  VEABT002 Module
Starter
Len
OP
Indi
CK
End
(0D 0A)h
'P': Send Product Information
External MCU  VEABT002 Module
Starter
Len
OP
External MCU  VEABT002 Module
FP
Prod.
S/N
Cal. Date
CK
End
(0D 0A)h
Starter
Len
OP
Indi
CK
End
(0D 0A)h
'M': Mode Switch
External MCU  VEABT002 Module
Starter
Len
OP
S/N
CK
End
(0D 0A)h
External MCU  VEABT002 Module
Starter
Len
OP
Indi
CK
End
(0D 0A)h
'A': Scan Product Information
External MCU  2ALHR001 Module
Starter
Len
'#'
OP
CK
'A'
End
(0D 0A)h
External MCU  2ALHR001 Module
Starter
Len
'>'
OP
SN
APO
Batt
RSSI
CK
'A'
End
(0D 0A)h
'B': Scan Measured Data
External MCU  2ALHR001 Module
Starter
Len
'#'
OP
SN
CK
'B'
End
(0D 0A)h
External MCU  2ALHR001 Module
Starter
'>'
Len
OP
APO
Batt
Data
RSSI
CK
'B'
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause
undesired operation.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
End
(0D 0A)h
residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications
not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment. (Example - use only shielded
interface cables when connecting to computer or peripheral devices).
End Product Labeling
This transmitter module is authorized only for use in devices.
The final end product must be labeled in visible area with the following:
“Contains FCC ID: 2ALHR001”
”
End Product Manual Information
The user manual for end users must include the following information in a
prominent location “IMPORTANT NOTE: To comply with FCC RF exposure
compliance requirements. This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions (1) This device may not
cause harmful interference and
(2) This device must accept any interference
received, including interference that may cause undesired operation.
IMPORTANT NOTE:
In the event that these conditions can not be met (for
example certain laptop configurations or colocation with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator
will be responsible for reevaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
This device is intended only for
OEM integrators under the following conditions:
As long as a condition above is met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their end
product for any additional compliance requirements required with this
module installed (for example, digital device emissions, PC peripheral
requirements, etc.). in conjunction with any other antenna or transmitter.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : PCUser
Create Date                     : 2017:05:22 13:45:06+08:00
Modify Date                     : 2017:05:22 13:45:06+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 11.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - 2ALHR001 Module User's Manual.docx
Creator                         : PCUser
Document ID                     : uuid:fc7080e9-777c-4d1b-b39b-c902f75ff1ed
Instance ID                     : uuid:d9ebe6a2-896c-4bd1-a674-4dab3aff6501
Page Count                      : 4

EXIF Metadata provided by EXIF.tools