Fieldpiece Instruments 004 Wireless Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3712786
Application ID	Ic4BLxAxCoEHP2PZBSQ1Ig==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	22.82kB (285310 bits)
Date Submitted	2018-01-13 00:00:00
Date Available	2018-01-13 00:00:00
Creation Date	2017-12-05 14:50:01
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2018-01-11 14:45:11
Document Title	Microsoft Word - 2ALHR004 Module User's Manual (1).docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	PCUser

2ALHR004 Module User's Manual
1. Features
‐ On‐chip low power microcontroller
‐ 128KB of In‐system programmable flash
‐ 8KB SRAM
‐ On board crystal and PFA Antenna
2. Application
‐ Mobile device accessories (Android/ iOS)
‐ Wireless data communication
‐ Remote sensors
3. Pin definition
Pin No.
Description
Pin Type
Functions
BLE_RX
Digital I/O
UART RX
BLE_TX
Digital I/O
UART TX
WAKE_UP
Output
Digital I/O
STATUS
Input
Digital I/O
GND
Digital I/O
GND
V+
Digital I/O
VDD
BLE_EN
Digital I/O
VDD Enable
4. How to use:
‐ Before sending any UART Command, "WAKE_UP 1  0" must be done by
external MCU.
‐ If the CC2640 module is connected to Smart Devices (Android/ iOS), the pin
STATUS will be logic "1" to inform external MCU.
‐ Beacon
‐
1. Send Command 'D'/'P' to send live measured data from external through
Beacon.
2. This is default mode, and 2ALHR002 module send data only. Cannot
receive any data.
BLE
‐
1. Send Command 'M' to switch mode from Beacon to BLE.
2. After the mode switch successfully, the external MCU can receive data
from Smart phone.
Receiver
1. Send Command 'A'/'B' to switch mode from Beacon to Receiver.
2. Only specific Beacon data can be received, and the external MCU receives
the data from UART
5. Protocol:
‐ UART Baud Rate: 115200, 8, N, 1
‐ Commands
'D': Send Measured Data
External MCU  2ALHR004 Module
Starter
Len
OP
Battery
Data
CK
End
(0D 0A)h
External MCU  2ALHR004 Module
Starter
Len
OP
Indi
CK
End
(0D 0A)h
'P': Send Product Information
External MCU  2ALHR004 Module
Starter
Len
OP
FP
Prod.
S/N
Len
OP
CK
End
(0D 0A)h
External MCU  2ALHR004 Module
Starter
Cal. Date
Indi
CK
End
>
(0D 0A)h
'M': Mode Switch
External MCU  2ALHR004 Module
Starter
Len
OP
S/N
CK
End
(0D 0A)h
External MCU  2ALHR004 Module
Starter
Len
OP
Indi
CK
End
(0D 0A)h
'A': Scan Product Information
External MCU  VEABT001 Module
Starter
Len
'#'
OP
CK
'A'
End
(0D 0A)h
External MCU  VEABT001 Module
Starter
Len
'>'
OP
SN
APO
Batt
RSSI
CK
'A'
End
(0D 0A)h
'B': Scan Measured Data
External MCU  VEABT001 Module
Starter
Len
'#'
OP
SN
CK
'B'
End
(0D 0A)h
External MCU  VEABT001 Module
Starter
'>'
Len
OP
'B'
APO
Batt
Data
RSSI
CK
End
(0D 0A)h
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the following
measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not
expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment. (Example - use only shielded interface cables when
connecting to computer or peripheral devices).
End Product Labeling
This transmitter module is authorized only for use in devices where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in visible area with the following: “Contains FCC ID:
2ALHR004”
End Product Manual Information
The user manual for end users must include the following information in a prominent
location “IMPORTANT NOTE: To comply with FCC RF exposure compliance
requirements, the antenna used for this transmitter must be installed to provide a
separation distance of at least 20cm from all persons and must not be colocated or
operating in conjunction with any other antenna or transmitter.”
This device
complies with part 15 of the FCC rules. Operation is subject to the following two
conditions (1) This device may not cause harmful interference and
(2) This device
must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example
certain laptop configurations or colocation with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for
reevaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
This device is intended only for OEM integrators under the following
conditions: The antenna must be installed such that 20 cm is maintained between the
antenna and users. As long as a condition above is met, further transmitter test will not
be required. However, the OEM integrator is still responsible for testing their end
product for any additional compliance requirements required with this module
installed (for example, digital device emissions, PC peripheral requirements, etc.).
Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
The host device shall be properly labelled to identify the modules within the host
device.
The Industry Canada certification label of a module shall be clearly visible at all
times when installed in the host device, otherwise the host device must be labelled
to display the Industry Canada certification number of the module, preceded by the
words “Contains transmitter module”, or the word “Contains”, or similar wording
expressing the same meaning, as follows:
“Contains transmitter module IC: 22518-BT004”
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator and your body.
Cet équipement est conforme aux CNR-102 d'Industrie Canada. Cet équipement
doit êtreinstallé et utilisé avec une distance minimale de 0.5 centimètres entre le
radiateur et votrecorps. Cet émetteur ne doit pas être co-localisées ou opérant en
conjonction avec autreantenne ou émetteur. Les antennes utilisées pour cet
émetteur doivent être installés etfournir une distance de séparation d'au moins
20 centimètre de toute personne et doit pas être co-située ni fonctionner en
conjonction avec une autre antenne ou émetteur.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : PCUser
Create Date                     : 2017:12:05 14:50:01+08:00
Modify Date                     : 2018:01:11 14:45:11+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Title                           : Microsoft Word - 2ALHR004 Module User's Manual (1).docx
Creator                         : PCUser
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2018:01:11 14:45:11+08:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:118db20d-a438-44f9-8a87-e6e5d49ed085
Instance ID                     : uuid:38100bff-a682-4084-9704-6e803bdab6c8
Page Count                      : 5

EXIF Metadata provided by EXIF.tools