Firetide 7100-1 Hotport Model 7100 Mesh Node User Manual Revised Manual

Download:
Mirror Download [FCC.gov]
Document ID	1224029
Application ID	27MpJsLFKbkyWNzJrDXK+g==
Document Description	Revised Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	78.36kB (979510 bits)
Date Submitted	2010-01-07 00:00:00
Date Available	2010-01-07 00:00:00
Creation Date	2010-01-07 12:42:21
Producing Software	Adobe PDF Library 9.0
Document Lastmod	2010-01-07 12:42:29
Document Title	Revised Manual
Document Creator	Adobe InDesign CS4 (6.0.4)

Hardware Installation Guide
HotPort
HotPort Series 7000
Indoor and Outdoor Wireless Mesh Nodes
mesh radio 1
mesh radio 2
status
power
HotPort 7100 - Indoor Node
Manual Revision 1.01-DRAFT 2010-01-07
The contents of this Installation Guide are subject to change without notice.
Please refer to the Firetide partners web site, partners.firetide.com, for current versions.
HotPort 7200 - Outdoor Node
Firetide Limited End User Product Warranty
Pursuant to all provisions described herein, Firetide hardware products
and Firetide antennas are warranted for one (1) year from the date of
purchase against defects in the build materials and workmanship. Firetide
does not warrant that the Products will meet any requirements or specifications of any End User Customer. This warranty applies to the entire
Firetide product, including the AC power adapter.
Pursuant to all provisions described herein, Firetide software products
are warranted for ninety (90) days from the date of purchase against defects in the build materials and workmanship. Firetide also warrants that
the Software will materially conform to the documentation supplied by
Firetide with the Software. In the event that the Software fails to materially conform to the documentation and an authorized Firetide reseller is
notified in writing of such failure within the warranty period, Firetide or
its reseller shall use commercially reasonable efforts to promptly correct
the nonconformity. Firetide does not warrant that the use of the Software
will be uninterrupted or error free.
The above warranties are void if the alleged defect cannot be verified by
Firetide or if, as determined by Firetide, the product failure was due to
tampering, abuse, misuse, accident, shipping, handling, or storage; or
if the product has been installed, used, or maintained in a manner not
described in the product user manual; or if the product has been altered
in any way; or if product serialization has been altered. Any attempt to
disassemble or repair the product by anyone other than Firetide immediately voids this warranty.
FRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT
ALLOW THE EXCLUSION OF IMPLIED WARRANTIES SO TO THAT EXTENT THIS
LIMITATION MAY NOT APPLY TO YOU.
In no event will Firetide be liable for any special, incidental, consequential, punitive or indirect damages whatsoever (including, without limitation, damages for loss of profits, business interruption, loss of information, or other pecuniary loss) arising out of the use or inability to use
the product or the performance, interruption or failure of the product,
irrespective of the cause of action, even if Firetide has been advised
of the possibility of such damages. Firetide’s cumulative liability for all
claims arising out of or in connection with this warranty will not exceed the amount paid by the original End User purchaser to purchase the
product. The amounts payable for the product are based in part on these
limitations and these limitations shall apply notwithstanding the failure
of essential purpose of any remedy. Some jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages, so to that
extent the above limitations or exclusions may not apply to you.
By using the product the original End User purchaser agrees to and is
bound by these terms and conditions.
In the event that a product fails to meet this warranty and Firetide’s
authorized reseller is notified in writing of such failure within the warranty period, Firetide shall, at its own discretion, either repair the product or replace it with the same or a functionally-equivalent product free
of charge. Replacement products may contain refurbished materials in
This warranty applies only to the original End User purchaser of the prod- whole or in part. Firetide will honor this warranty provided the product is
uct and may not be transferred to any other individual or entity.
returned through an authorized Firetide reseller or dealer with shipping
THE FOREGOING ARE THE EXCLUSIVE WARRANTIES APPLICABLE TO THE charges prepaid, along with a proof of purchase describing the original
PRODUCT INCLUDING THE SOFTWARE, AND THE EXCLUSIVE REMEDY FOR purchase date and product serial numbers if applicable. The authorized
DEFECTS IN THE PRODUCT. FIRETIDE DISCLAIMS ALL OTHER WARRANTIES, reseller must acquire a Return Materials Authorization (RMA) number from
WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING BUT Firetide prior to returning any product. Firetide does not accept shipNOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, NON-IN- ments of defective products without shipping charges prepaid.
Safety Instructions
The HotPort outdoor wireless mesh node must be installed by a qualified professional such as a licensed electrician. Failure to install this
equipment properly may result in equipment damage and personal
injury or death.
This symbol is intended to alert the user to the presence of non-insulated dangerous voltage that may be
of sufficient magnitude to constitute a risk of lethal
electric shock to persons.
This symbol is intended to alert the user to the presence of important operating, maintaining and servicing instructions in the literature accompanying the
HotPort node. Failing to comply with this instruction
may result in electrical shock.
This symbol is intended to alert the user to the presence of important operating, maintaining and servicing instructions in the literature accompanying the
HotPort node. Failing to comply with this instruction
may result in a hazard.
Copyright Notice: ©2003-2010 Firetide, Inc. All rights reserved.
Trademarks: Firetide, the Firetide logo, Instant Mesh Networks, HotPort, and HotPoint are trademarks of Firetide, Inc. All other trademarks are the
property of their respective owners.
HotPort Series 7000 Mesh Nodes
January 2010
Contents
HotPort Node Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5
Planning Your Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6
Indoor Node Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Positioning Indoor Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Outdoor Node Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Preparing the Unit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  7
Preparing Earth Ground  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  7
Safety Considerations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  7
Antenna Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8
Mounting Outdoor Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mounting Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8
Mounting the Universal Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9
Using Mounting Straps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Power Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Appendix A - Contacting Firetide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Appendix B - Connector Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
HotPort Outdoor Node AC Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
HotPort Outdoor Node DC Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Custom Power Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Appendix C - Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Common Specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wireless Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Series 7200 Outdoor Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Series 7100 Indoor Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Appendix D - Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
USA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Canadian Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
January 2010
Firetide Instant Mesh Networks 3
Caution! Risk of electric shock!
POWER LINES CAN BE LETHAL
Do not install the HotPort outdoor mesh node where possible contact with power lines can be made. Antennas, poles, towers, guy
wires, or cables may lean or fall and contact these lines. People
may be injured or killed if they are touching or holding any part
of the equipment when it contacts electric lines. Make sure there
is NO possibility that equipment or personnel can come in contact
directly or indirectly with power lines.
ASSUME ALL OVERHEAD LINES ARE POWER LINES
The horizontal distance from a tower, pole or antenna to the nearest power line should be at least twice the total length of the
pole/antenna combination. This will ensure that the pole will not
contact power if it falls either during or after installation.
SURVEYING THE SITE
Look over the entire site before beginning any installation and anticipate possible hazards. Never assume anything without checking it out for yourself! Don’t take shortcuts!
• If a tower or pole begins falling, don’t attempt to catch it.
Stand back and let it fall.
• If anything such as a wire or pole does come in contact with a
power line, DON’T TOUCH IT OR ATTEMPT TO MOVE IT. Instead,
save your life by calling the power company.
• Don’t attempt to erect antennas or towers on windy days.
• MAKE SURE ALL TOWERS AND POLES ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO ANTENNAS HAVE
LIGHTNING ARRESTORS. This will help prevent fire damage or
human injury in case of lightning, static build-up, or short circuit within equipment connected to the antenna. The HotPort
outdoor node has built-in lightning protection. Be sure that
any other equipment connected to the HotPort node also has
the same level of protection.
• The base of the antenna pole or tower must be connected directly to the building protective ground or to one or more
approved grounding rods, using 10 AWG ground wire and corrosion-resistant connectors.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT • Refer to the National Electrical Code for grounding details.
IF AN ACCIDENT SHOULD OCCUR WITH THE POWER LINES:
HEIGHTS ABOVE GROUND
• Select equipment locations that will allow safe and simple installation.
• Don’t work alone. A friend or co-worker can save your life if an
accident happens.
• Don’t attempt repair work when you are tired. Not only will
you be more careless, but your primary diagnostic tool deductive reasoning - will not be operating at full capacity.
• DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.
• Use a non-conductive dry board, stick, or rope to push or drag
them so they no longer are in contact with electrical power.
• Once they are no longer contacting electrical power, administer
CPR if you are certified.
• Immediately have someone call for medical help.
• Use approved non-conducting ladders, shoes, and other safety
equipment. Make sure all equipment is in good repair.
Do not open the cover
• Dangerous voltages inside.
• No serviceable parts inside.
• Refer to qualified service personnel.
• Unit must be disconnected from power prior to servicing.
• Unit has tamper-evident labeling that indicates when the cover has been removed.
HotPort Series 7000 Mesh Nodes
January 2010
HotPort Node Installation
This hardware installation guide describes how to install the HotPort node safely. The HotPort is intended to be installed by trained
professionals. Be sure to read and understand all installation and safety instructions before proceeding with the installation.
Table 1. Summary of HotPort Series 7000 Mesh Nodes
Model
7100
7200
Use
Indoor, Worldwide, 2.4, 4.9, 5 GHz
Outdoor, Worldwide, 2.4, 4.9, 5 GHz
No. of Radios
1 or 2
1 or 2
This guide covers both dual-radio and single radio models. The only difference between dual-radio models and single-radio models is
the second radio. Single radio models will identify themselves in software as 7101 or 7201; dual radio models will identify themselves
as 7102 or 7202.
Package Contents
The HotPort node package contains the following items. If you are missing any of these items, contact your Firetide reseller.
HotPort 7100 Indoor Mesh Node
• HotPort node in plenum-rated enclosure.
Antennas
HotPort 7200 Outdoor Mesh Node
• HotPort node in NEMA-4X enclosure with weatherproof caps.
• Six N to reverse-polarity SMA adapters.
• Mounting bracket for pole and wall mounting. Designed to fit
37 mm to 50 mm (1.5 in to 2.0 in) poles.
• Six detachable 2.4 GHz 5 dBi omnidirectional antennas.
• Six detachable 5 GHz 5 dBi omnidirectional antennas.
• These are the only antennas approved for use with the 7100 in Mounting Kit
the 2.4, 4.9, and 5 GHz bands..
• U-Bolts, M6x1.0-80mm, with flat washers, split washers, nuts.
• Claw-tooth pole grippers.
Power
• M6x1.0-40mm hex bolt.
• External power module with NEMA5-15 (US) to IEC-320 cord.
• M6x1.0-20mm hex bolt.
Other IEC cords are available separately.
• Hex-head socket wrench.
Documentation
• HotPort 7100 Quick Install Guide.
• Warranty and registration card.
Compact Disk (CD)
• HotView Pro software.
• HotView Pro Reference Guide.
• HotPort 7000 Hardware Installation Guide
• Warranty/Registration Card.
• EULA.
Antennas
• Six detachable 2.4 GHz indoor omnidirectional antennas.
• Six detachable 5 GHz indoor omnidirectional antennas.
Power
• AC power cord with NEMA 5-15 (US) plug. Other IEC cords are
available separately.
Documentation
• HotPort 7200 Quick Install Guide.
• Warranty and registration card.
Compact Disk (CD)
• HotView Pro software.
• HotView Pro Reference Guide.
• HotPort Series 7000 Hardware Installation Guide.
• Warranty/Registration Card.
• EULA.
January 2010
Firetide Instant Mesh Networks 5
Planning Your Installation
Staging Considerations
You should set up and test your nodes indoors, on a bench or
table, before installing them. This will allow you to pre-configure
the nodes so that they are all on the same RF channel, etc. You
will use HotView Pro to configure the HotPort nodes and create a
small mesh network. Test the network settings you plan to use.
Warning: The staging antennas provided with Firetide outdoor
nodes are for temporary use only. They MUST be replaced with outdoor-rated antennas as soon as the
mesh is staged and operational. The staging antennas
are NOT waterproof and NOT moisture resistant. If used
outdoors, the antennas may fail.
Your CD has a copy of Firetide’s Accessory Guide. Contact your
1. Check to see that all nodes are visible in HotView Pro. If not,
Firetide Reseller for assistance in selecting and ordering outdoor
troubleshoot per directions in the HotView Reference Guide.
antennas suitable for your application(s).
2. Set the Country Code for your country of operation.
3. Re-verify that all nodes are visible, and verify that dual-radio
nodes have both radios correctly meshed.
Indoor Node Installation
Indoor node installation is straightforward. Firetide recommends
that you power up and configure all nodes on a table or bench
before deployment. Use HotView or HotView Pro to configure your
mesh. Place the unit on a table or shelf. Apply power. The power
LED should illuminate immediately; after about 60 to 90 seconds,
the status LED should switch to steady green.
Note the location of the reset button in the lower right corner of
the rear panel. To reset the unit, apply power and wait until the
unit has fully booted and the status light has come on. Then use
a paperclip to press and hold the reset button until the status LED
blinks.
Positioning Indoor Antennas
Figure 2. HotPort Series 7100 Mesh Node - Front View
mesh radio 1
mesh radio 2
status
power
Figure 3. HotPort Series 7100 Mesh Node - Rear View
The Firetide-supplied antennas are rated for use in dry, indoor
environments. If the antenna is exposed to weather, moisture, or
high humidity, it may fail. Use an approved outdoor-rated antenna
instead.
MIMO technology takes advantage of signal reflections to improve
performance. Antenna orientation affects this. Firetide recommends that you begin deployment with the antennas on each radio parallel and in the same plane as the node itself.
Depending on performance, you may wish to try other orientations.
Figure 1. Staging Antennas
Figure 4. Power Supply
HotPort Series 7000 Mesh Nodes
January 2010
Outdoor Node Installation
Preparing the Unit
1. Pre-assemble the antenna, HotPort node, and other devices to
a metal pole and antenna and then relocate and attach it to a
roof top. It is often easier to install all devices to one object,
such as a pole, and then attach the pole to the roof. In many
cases, connecting the devices to a pole already attached to
the roof top can be difficult and dangerous.
WARNING
The staging antennas provided with Firetide outdoor
nodes and access points are for temporary use only.
They MUST be replaced with outdoor-rated antennas
as soon as the mesh is staged and operational.
The staging antennas are NOT waterproof or moisture resistant. If
2. A lightning surge suppressor must be used. Some antennas
used outdoors or in humid environments, the antennas may fail.
include one. If not, you must install a lightning suppressor.
Your CD has a copy of Firetide’s Accessory Guide. Contact your
3. Install the antenna and any wireless devices higher than the
Firetide Reseller for assistance in selecting and ordering outdoor
HotPort node. Take care when locating the HotPort node far
antennas suitable for your application(s).
away from the antenna; a short antenna cable gives better
performance than a longer one. Firetide recommends that you Tools Needed
use antenna cables less than 3 meters.
For HotPort 7200 outdoor nodes, you will need:
4. The HotPort node and its antenna must both be grounded.
• #2 Phillips screwdriver.
5. Use weatherproofing kits that include non-vulcanized rubber
to weatherproof connectors and antennas. All Ethernet cables • Small adjustable wrench.
must be waterproofed; standard RJ-45 connectors do not last • Wire cutters to cut tie wraps around cables.
outdoors.
• Weatherproofing kit – this kit provides electrical tape and butyl
6. Power over Ethernet: Consider which devices require PoE and
mastic.
what the required input voltage will be.
Depending on the installation location, you may need ladders, a
7. Connect peripheral devices to the HotPort node.
lift truck, or other means to access the actual installation locations.
8. Connect power to the HotPort node and peripherals.
Preparing Earth Ground
The HotPort node must be properly connected to earth ground.
Failure to do so may result in equipment damage, injury, or death.
The product warranty does not cover damages resulting in part or
in whole from improper grounding. Consult your location’s building and electrical codes regarding antennas and follow them, or
consult the National Electric Code (NEC).
• If connecting to a tower or pole, connect the base of the tower
pole directly to the building’s ground or to one or more approved grounding rods using 10 AWG ground wire and corrosion-resistant connectors.
• Connect the grounding cable to rain gutters only if the
rain gutter is connected to earth ground.
• Ground rods should be copper-plated, 1.8 - 2.4 m (6 - 8 ft)
long.
• Install all grounding components in straight lines. If bends are
unavoidable, do not make sharp turns.
• Earth-to-ground should not be more than 10 ohms.
• Understanding the soil is very important in order to create a
proper earth ground. If your soil is rocky or sandy, drive your
ground rods and then pull them back out and dump an approved ground enhancement material into the holes where the
grounding rods go. Then replace the grounding rods. Keep in
mind that some salt compounds are corrosive and can cause
copper to corrode.
Safety Considerations
Consider the following safety issues.
• Use approved, non-conducting ladders.
• If mounting to a pole or tower, make sure all poles and towers
are securely grounded.
• Use approved and non-conducting shoes and other safety
equipment. Make sure that all equipment is in good repair.
• Make sure antennas are DC grounded; if not, cables must have
lightning arrestors.
January 2010
Firetide Instant Mesh Networks 7
Antenna Placement
Firetide recommends the use of antennas specifically designed for
MIMO applications. While it is possible to select and mount six
individual antennas, determining correct placement and spacing
is difficult. Use an antenna engineered for best results with MIMO.
If you are not using three antennas on each radio, install antennas in order, from the front of the unit toward the back. Do not
‘skip’ antenna connections.
Mounting Outdoor Antennas
Once you determine which RF band to use, you can order spectrumspecific high-gain antennas from Firetide or another supplier.
Many installers prefer to mount the HotPort node and its associated antennas to a short bar, typically about 2 meters long. This
entire bar assembly is them mounted horizontally to the vertical
mast of the main antenna structure.
Mounting Guidelines
• It is often easier to install all devices onto a pole, and then
attach the pole to the roof. In many cases, connecting the devices to a pole already attached to the roof top can be difficult
and dangerous.
• A lightning surge suppressor must be used. Some antennas
include one. If not, install a lightning surge suppressor.
• Locate the HotPort close to the antenna; a short antenna cable
gives better performance than a longer one. Firetide recommends antenna cables less than 3 meters.
• The HotPort node and its antenna must both be grounded.
• Large or heavy antennas must be mounted to a pole or other
secure structure.
• The antennas should not be within 1 meter (~3 ft.) of any metal
bar or structure, and ideally not within 1 meter (~3 ft.) of any
concrete or stone structure. In general, try to locate the antennas as far from such objects as practicable.
• Shorter antenna cables give better performance. Plan your installation to minimize antenna cable length. However, do not
attempt to splice or shorten the antenna cable.
• If a longer coax cable is required, the system requires a highquality, low-loss 50 ohm cable. Contact your local distributor
to obtain a 50 ohm cable with the correct connectors. Firetide
recommends LMR400 cable or better.
• Minimize use of connectors and adapters.
• Once you’ve verified that everything is working, waterproof all
connections!
• Do not mount the antenna pole near power lines.
• When mounting next to an access point, mount the access
point lower on the pole and at least 1 meter (~3 ft.) from the
antennas. You can also mount the access point on a horizontal
bar to achieve the required separation.
Mounting Bracket
Your HotPort node shipped with a two-piece mounting bracket. The inner bracket can be left attached to the node, as shown
This bracket is of the same design as the HotPort 6202 outdoor below.
bracket, so you can install a 7200 in place of a 6201 or 6202.
The assembly is shown below. To mount the node, remove the
outer piece, by loosening the thumb screws.
HotPort Series 7000 Mesh Nodes
January 2010
Mounting the Universal Bracket
You can mount the node to a wall, a light pole, or an irregularly
shaped pole. The universal mounting bracket has been designed
with multiple holes and slots to allow mounting with bolts, straps,
or other methods. Extra nuts and bolts are provided for this purpose; don’t be alarmed if you have leftover fasteners when installation is complete.
Universal Mounting Bracket
Attached to Pole
Wall Mounting
The Universal Mounting Bracket contains holes and slots to allow
it to be mounted via U-bolts or straps. Use four screws (not supplied) to attach the universal mounting bracket securely to the
wall using the four holes near the top and bottom of the universal
mounting bracket. Use appropriate anchors when attaching to masonry or other materials.
This shows the use of spacer nuts when mounting to smaller poles.
You may find an open-end wrench useful for tightening the inner
1. Insert the two U-bolts through the holes in the claw-toothed nuts in these applications.
pole-gripper piece.
Pole Mounting
2. On each U-bolt, place a washer, a lock washer, and a nut.
Smaller pole diameters usually require a second nut as a spacer to hold the bracket away from the U-bolt clamp. Fingertighten the nuts. There should be about 12-15 mm (1/2-5/8”)
of U-bolt sticking past the second nut.
U-bolt Mounted
on Pole
Mounting Bracket
Showing Use of
Spacer Nuts
Using Mounting Straps
For poles with diameters larger than 50 mm (2”), irregularly
Mount the second U-bolt. Use the mounting bracket as a guide to
shaped poles, or light poles, you can use mounting straps (not
correctly space the two U-bolts, then tighten the nuts. A horizonsupplied) to mount the HotPort enclosure.
tal pole-mount is also shown for reference.
1. Position the universal mounting bracket against the pole.
2. Thread two mounting straps around the pole and through the
slots located near the top and bottom of the universal mounting bracket. Secure the mounting straps.
3. Attach the enclosure to the universal mounting bracket by
sliding the metal clips on the back of the enclosure into the
metal straps on the universal mounting bracket.
U-bolts, Vertical and
Horizontal Mounting
Secure the enclosure to the universal mounting bracket using the
four captive screws on the sides of the universal mounting bracket.
Mounting Antennas
Use lock washers and nuts to secure the bracket to the U-bolts. Now that you’ve attached the Universal Mounting Plate, you are
Installation on a horizontal pole is the same, you just use differ- ready to proceed to the next steps. Most outdoor applications use
separately-mounted antennas, if so, mount your antennas now. If
ent holes in the mounting plate.
you are using the temporary staging antennas, the next step is to
attach the HotPort node itself.
January 2010
Firetide Instant Mesh Networks 9
Connecting Cables
After your node is mounted, attach the six antennas, the power cable, and any Ethernet cables you need. Note that all of the weatherproof caps have been removed from the node for illustrative purposes. You should not leave any unused connector uncovered.
Figure 5. HotPort 7200 Bottom Panel
ac power
dc power
power
port 3
status
port 2
radio 1
radio 2
–mesh–
port 1
usb
ethernet
Note the locations of the reset button under the weatherproof cap. To reset the unit, apply power and wait until the unit has fully
booted and the status light has come on. Then use a paperclip to press and hold the reset button until the status LED blinks.
Power Connection
Connect the suppled AC power cable to AC power and to the HotPort node. If you wish to power your node with DC power, you will
need a source of power which can deliver 12 V ±10% at 3 A. Information on building custom power cables is shown in Appendix B. Do
not connect both AC and DC supplies simultaneously.
Powering Other Ethernet Devices
Ports 2 and 3 on a Series 7200 node can provide Power over Ethernet (PoE) functionality to Powered Devices (PD) connected to these
ports. (Port 1 cannot.) A Powered Device can receive data and the power to process the data from the HotPort node, which functions as
Power Sourcing Equipment (PSE) in this configuration. To receive power from a HotPort node, the device must support the IEEE 802.3af
standard, which defines PoE functionality.
Connecting Antennas
Don’t forget to order your permanent outdoor antennas! You can’t use the staging antennas outdoors, they might fail.
When connecting antennas, connect them in numerical order 1-2-3. If you are not using three antennas per radio, do not ‘skip’ antenna
connectors. The antenna 1 connector is at the top of the unit (farthest from the power and Ethernet connections) on both the left
and right side.
radio 2
radio 1
antenna 1
10
antenna 2
HotPort Series 7000 Mesh Nodes
antenna 3
antenna 3
antenna 2
antenna 1
January 2010
Appendix A - Contacting Firetide
Dealer-Provided Technical Support and Warranty Service
Sales Assistance
If you need additional technical assistance, please contact your
Firetide dealer directly. All authorized Firetide dealers are trained
and authorized to provide technical support and warranty services
for our products and have qualified technical staff available to
help you build and maintain your Firetide mesh network.
If you need additional HotPort wireless mesh nodes or accessories, please contact your Firetide dealer directly. If you do not
know your dealer’s name, simply email sales@firetide.com and
we will send you the dealer information you need. To help us
provide the best service possible, be sure to include your phone
number, address, and the serial numbers of the HotPort nodes at
your location.
Firetide-Provided Technical Support
You can also get technical support from Firetide. Simply email
support@firetide.com, or call 1-877-FIRETIDE, extension 2, or +1
408 399 7771.
Product Returns
Mailing Address
Firetide, Inc.
140 Knowles Drive
Los Gatos, CA 95032 USA
Please contact your Firetide dealer for instructions on returning
defective or damaged products for repair or replacement. Do not
return products to Firetide, Inc. Please keep all original packaging
materials in the event they are needed to return the product for
servicing.
January 2010
Firetide Instant Mesh Networks 11
Appendix B - Connector Wiring
HotPort Outdoor Node AC Power Connector
Figure 6 shows the pinout of the AC Power connector used on Series 7200 outdoor nodes. Views are shown of both the connector on
the unit, and the mating connector on the cable itself. Pin 1 is neutral; pin 2 is line, and pin 3 is ground.
Figure 6. Series 7200 AC Power Connector
3-ground
3-ground
2-line 1-neutral
1-neutral 2-line
Series 6200 AC Power
Connector View
Series 6200 AC Power
Cable-End View
HotPort Outdoor Node DC Power Connector
Figure 7 shows the pinout of the power connector used to supply power to Series 7200 nodes. Each view is of the cable connector, as
viewed end-on. Pin 4 is +12VDC power. Pin 3 is ground.
Figure 7. Series 7200 DC Power Connector
Series 6200 DC Power Connector
3 ------- ground ------- 3
4 --- power --- 4
Cable-End View
Connector View
Custom Power Cables
Firetide offers an accessory DC power cable. The part number is 3200-2401, and this cable can be used to connect other DC sources
to your Series 7200 node. One end of the cable has the six-pin connector used by the Series 7200; the other end has a weatherproof
4-pin connector. Both connectors are of the LTZ type. The cable is wired as shown in Figure 8.
Custom cables can be built in either of two ways.
1. You can obtain a 4-pin female LTZ connector and build an adapter cable.
2. You can cut the 4-pin male LTZ connector off the cable and attach whatever type of connector you require.
Figure 8. DC Power Adapter Cable Wiring
Pin 1
4-pin LTZ
Connector
Pin 2
Pin 3
blue
positive-lead power
(nominal +15 volts)
Pin 4
black
ground/drain
Pin 4
Series 6200
DC Power Connector
brown
white
Pin 3
3 ------- ground
4 ---- power
Cable-End View
DC power to a HotPort node must be 12 VDC ±15%, at 3A. Series 7200 nodes can provide PoE-compliant 48 VDC power to other devices.
12
HotPort Series 7000 Mesh Nodes
January 2010
Appendix C - Specifications
Common Specifications
Supported Data Rates & Standards
• 802.11a
Wireless Interface
These tables describes the technical limits of the nodes. Various
country restrictions may further limit available choices.
Model
7100
7200
Use
Indoor, Worldwide, 2.4, 4.9, 5 GHz
Outdoor, Worldwide, 2.4, 4.9, 5 GHz
Single-radio HotPort 7100 nodes appear as 7101.
Dual-radio HotPort 7100 nodes appear as 7102.
Single-radio HotPort 7200 nodes appear as 7201.
Dual-radio HotPort 7200 nodes appear as 7202.
For all models:
Bands (GHz) Frequency (GHz)
802.11a
5.15-5.25
802.11n
Restrictions
5.725-5.825
4.9-5.090
Japan only
4.94-4.990
5.470-5.725
US Public Safety
ETSI 301.893, U-NII
2.412-2.484
802.11n
• 802.11b
1/2/5.5/11Mbps
• 802.11g
6/9/12/18/24/36/48/54Mbps
• 802.11n
6.5/13/19.5/26/65/130/195/260 (1)
7.2/14.4/21.7/28.9/72.2/144/216.7/288.9 (2)
13.5/27/40.5/54/135/270 (3)
15/30/45/60/150/300 (4)
(1) 20MHz LGB (2) 20MHz SGB (3) 40MHz LGB (4) 40MHz LGB
• Network Standards: IEEE 802.11a/b/d/g/e/f/h/i/n
• Dynamic Frequency Selection (DFS) capable in conjunction with
Firetide Software application
• Firetide AutoMesh Protocol
Mesh Management Software
• HotView Pro™ mesh management software
Security & Encryption
Bands (GHz)
Max TX Power
802.11a
26dBm
5.725-5.825 UNII-3
26dBm
802.11n
24dBm
23dBm
• 802.11a
Capable of switching to 1⁄4 and 1⁄2 rates for
4.940 – 4.990 GHz Public Safety Band
Mesh Protocol
5.25-5.35
802.11b/g
No. of Radios
1 or 2
1 or 2
6/9/12/18/24/36/48/54Mbps
5.470-5.735 UNII
5.25-5.36 M UNII-2
5.15-5.25 UNII-1
23 dBm
23 dBm
802.11b
17 dBm
24 dBm
802.11g
26dBm
802.11n
26dBm
January 2010
• Security: WPA—64/128/256 w/TKIP, AES,
Antennas
• Twelve detachable omnidirectional, vertical polarization, six for
each band.
Regulatory Agency Certifications
• Contact your Firetide dealer for product availability and certifications for your country.
Firetide Instant Mesh Networks 13
Series 7200 Outdoor Unit Specifications
Series 7100 Indoor Unit Specifications
Network Ports
Network Ports
• Three 10/100/1000 Mbps Ethernet ports with weatherproof
connectors, LED activity indicator
• IEEE 802.3, 802.3u compliant
• CSMA/CD 10/100/1000 autosense
• Ports 2, 3 PSE Power over Ethernet per 802.3at
Enclosure
• Cast aluminum NEMA-4X/IP66 enclosure
• Six N-type antenna connectors
• Two weatherproof power connectors (AC and DC)
• Three weatherproof Ethernet connectors
• System LEDs (power, status, mesh (per radio), ethernet)
• Weight: 12 lbs (5.5 Kg) with bracket
• Dimensions: 8.8” x 11.2” x 4” (220 x 280 x 100 mm)
Power
• AC Input: 90-240 VAC, 50-60 Hz, 0.9A
• DC Input: 12 VDC ±15%, 3 A
• Port 2: IEEE 802.3af compliant PoE (PSE), 13.5 W max
• Port 3: IEEE 802.3af compliant PoE (PSE), 13.5 W max
Environmental Specifications
• Operating temperature: -40º C to +60ºC
• Storage temperature: -40º C to +85º C
• Humidity (non-condensing): 10% to 90%
• Storage humidity (non-condensing): 5% to 95%
• Maximum altitude 15,000 feet (4600 meters)
• Four 10/100/1000 Mbps Ethernet ports with LEDs
• PoE PD on Port 1
• IEEE 802.3, 802.3u compliant
• CSMA/CD 10/100/1000 autosense
Enclosure
• Plenum-rated metal enclosure
• Six RP-SMA antenna connectors
• One DC power connector
• Four Ethernet connectors
• System indicator LEDs: power, status, per-radio mesh, ethernet
• Weight: 3 lbs (1.4 Kg)
• Dimensions: 9.4” x 6” x 1.8” (238 x 152 x 48 mm)
Power
• DC Input: 12 VDC ±15%, 3 A
Environmental Specifications
• Operating temperature: 0º C to +60ºC
• Storage temperature: -20º C to +70º C
• Humidity (non-condensing): 10% to 90%
• Storage humidity (non-condensing): 5% to 95%
• Maximum altitude 15,000 feet (4600 meters)
Included Accessories
• AC power adapter
• Six 2.4 GHz and six 4.9-5.8 GHz 5 dBi omni staging antennas,
for indoor use only.
Included Accessories
• Bracket for pole and wall mounting
• External power cord
• Six 2.4 GHz and six 4.9-5.8 GHz 5 dBi omni staging antennas,
for indoor and temporary use only. The 7200 has been certified
with a 9 dBi omni, 16 dBi sector, and 19 dBi panel outdoor
antenna. Contact Firetide for part numbers and ordering information.
14
HotPort Series 7000 Mesh Nodes
January 2010
Appendix D - Regulatory Notices
USA
FCC Radiation Exposure Statement
To ensure compliance with the FCC’s RF exposure limits, the antenna used for this transmitter must be installed to provide a
This device complies with Part 15 of the FCC Rules. Operation is separation distance from all persons.
subject to the following two conditions:
• For the 7100, the distance must be 20 cm.
• This device may not cause harmful interference.
• For the 7200, the distance must be 76 cm.
• This device must accept any interference received, including
The 7100 and 7200 must not be co-located or operated in coninterference that may cause undesired operation.
junction with any other antenna or transmitter. Installers and end
users must follow these installation instructions.
FCC Part 15 Note
FCC Class A Notice
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in an office installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
Installation
Antenna(s) for this unit must be installed by a qualified professional. Operation of the unit with non-approved antennas is a
violation of U.S. FCC Rules, Part 15.203(c), Code of Federal Regulations, Title 47.
Canadian Compliance Statement
This Class A Digital apparatus meets all the requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe A respecte les exigences du
Reglement sur le material broilleur du Canada.
This device complies with Class A Limits of Industry Canada. Operation is subject to the following two conditions:
• Connect the equipment into an outlet on a circuit different 1. This device may not cause harmful interference, and
from that to which the receiver is connected.
2. This device must accept any interference received, including
• Consult the dealer or an experienced radio/television techni- interference that may cause undesired operation.
cian for help.
Firetide HotPoint 7100 and 7200 wireless mesh nodes are certified
to the requirements of RSS-210 for 2.4 and 5 GHz spread spectrum devices. The use of this device in a system operating either
This equipment has been tested pursuant to FCC Part 90, DSRC-C partially or completely outdoors may require the user to obtain a
mask certification, and is approved for use in the US on Public license for the system according to the Canadian regulations. For
Safety bands by licensed Public Safety agencies.
further information, contact your local Industry Canada office.
FCC Part 90 Note
Public Safety Band
Canadian units will not transmit in the 5600-5650 MHz band.
Pursuant to Part 90.1215, use of antennas with gain greater than
9 dBi and up to 19 dBi in the 4.940 - 4.990 GHz Public Safety
band is permissible without reduction of TX output power. The
antenna shall have a directional gain pattern in order to meet the
requirement of point to point and point to multi-point operation.
Modifications
Any modifications made to this device that are not approved by
Firetide, Inc. may void the authority granted to the user by the
FCC to operate this equipment.
January 2010
Firetide Instant Mesh Networks 15
Firetide, Inc.
140 Knowles Drive
Los Gatos, CA 95032

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.2-c063 53.352624, 2008/07/30-18:05:41
Create Date                     : 2010:01:07 12:42:21-08:00
Metadata Date                   : 2010:01:07 12:42:29-08:00
Modify Date                     : 2010:01:07 12:42:29-08:00
Creator Tool                    : Adobe InDesign CS4 (6.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 9628 bytes, use -b option to extract)
Instance ID                     : uuid:f20fddba-fd65-9246-97f4-08d18c4cebd5
Document ID                     : xmp.did:D9040EE21C20681197A59DD54EE0A9C9
Original Document ID            : adobe:docid:indd:37a099f0-f9c0-11dd-aa72-f3d39728dbbb
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:D8040EE21C20681197A59DD54EE0A9C9
Derived From Document ID        : xmp.did:028011740720681197A59DD54EE0A9C9
Derived From Original Document ID: adobe:docid:indd:37a099f0-f9c0-11dd-aa72-f3d39728dbbb
Derived From Rendition Class    : default
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:ED7F117407206811B34BFCE4DCB8903B, xmp.iid:EE7F117407206811B34BFCE4DCB8903B, xmp.iid:EF7F117407206811B34BFCE4DCB8903B, xmp.iid:F07F117407206811B34BFCE4DCB8903B, xmp.iid:F17F117407206811B34BFCE4DCB8903B, xmp.iid:F27F117407206811B34BFCE4DCB8903B, xmp.iid:F37F117407206811B34BFCE4DCB8903B, xmp.iid:F47F117407206811B34BFCE4DCB8903B, xmp.iid:F57F117407206811B34BFCE4DCB8903B, xmp.iid:F67F117407206811B34BFCE4DCB8903B, xmp.iid:08B89C850C206811B34BFCE4DCB8903B, xmp.iid:09B89C850C206811B34BFCE4DCB8903B, xmp.iid:0AB89C850C206811B34BFCE4DCB8903B, xmp.iid:0BB89C850C206811B34BFCE4DCB8903B, xmp.iid:9D061EF21B206811B34BFCE4DCB8903B, xmp.iid:4791B99729206811B34BFCE4DCB8903B, xmp.iid:4891B99729206811B34BFCE4DCB8903B, xmp.iid:4991B99729206811B34BFCE4DCB8903B, xmp.iid:4A91B99729206811B34BFCE4DCB8903B, xmp.iid:F77F1174072068119109A7BD3A8ADC66, xmp.iid:F87F1174072068119109A7BD3A8ADC66, xmp.iid:F97F1174072068119109A7BD3A8ADC66, xmp.iid:FA7F1174072068119109A7BD3A8ADC66, xmp.iid:FB7F1174072068119109A7BD3A8ADC66, xmp.iid:FC7F1174072068119109A7BD3A8ADC66, xmp.iid:FD7F1174072068119109A7BD3A8ADC66, xmp.iid:FE7F1174072068119109A7BD3A8ADC66, xmp.iid:FF7F1174072068119109A7BD3A8ADC66, xmp.iid:00801174072068119109A7BD3A8ADC66, xmp.iid:90A49C230E2068119109A7BD3A8ADC66, xmp.iid:91A49C230E2068119109A7BD3A8ADC66, xmp.iid:92A49C230E2068119109A7BD3A8ADC66, xmp.iid:93A49C230E2068119109A7BD3A8ADC66, xmp.iid:94A49C230E2068119109A7BD3A8ADC66, xmp.iid:95A49C230E2068119109A7BD3A8ADC66, xmp.iid:96A49C230E2068119109A7BD3A8ADC66, xmp.iid:97A49C230E2068119109A7BD3A8ADC66, xmp.iid:98A49C230E2068119109A7BD3A8ADC66, xmp.iid:99A49C230E2068119109A7BD3A8ADC66, xmp.iid:9AA49C230E2068119109A7BD3A8ADC66, xmp.iid:C4F67BA21A2068119109A7BD3A8ADC66, xmp.iid:C5F67BA21A2068119109A7BD3A8ADC66, xmp.iid:C6F67BA21A2068119109A7BD3A8ADC66, xmp.iid:C7F67BA21A2068119109A7BD3A8ADC66, xmp.iid:C8F67BA21A2068119109A7BD3A8ADC66, xmp.iid:CFA2E3CE702068119457EE89CBA16AD0, xmp.iid:D0A2E3CE702068119457EE89CBA16AD0, xmp.iid:D1A2E3CE702068119457EE89CBA16AD0, xmp.iid:D2A2E3CE702068119457EE89CBA16AD0, xmp.iid:D3A2E3CE702068119457EE89CBA16AD0, xmp.iid:F77F1174072068118F62DF08E6AF9C04, xmp.iid:F87F1174072068118F62DF08E6AF9C04, xmp.iid:F97F1174072068118F62DF08E6AF9C04, xmp.iid:FA7F1174072068118F62DF08E6AF9C04, xmp.iid:FB7F1174072068118F62DF08E6AF9C04, xmp.iid:FD7F117407206811B481932CF08869F6, xmp.iid:FE7F117407206811B481932CF08869F6, xmp.iid:018011740720681197A59DD54EE0A9C9, xmp.iid:028011740720681197A59DD54EE0A9C9, xmp.iid:038011740720681197A59DD54EE0A9C9, xmp.iid:048011740720681197A59DD54EE0A9C9, xmp.iid:058011740720681197A59DD54EE0A9C9, xmp.iid:068011740720681197A59DD54EE0A9C9, xmp.iid:078011740720681197A59DD54EE0A9C9, xmp.iid:088011740720681197A59DD54EE0A9C9, xmp.iid:098011740720681197A59DD54EE0A9C9, xmp.iid:0A8011740720681197A59DD54EE0A9C9, xmp.iid:D8040EE21C20681197A59DD54EE0A9C9, xmp.iid:D9040EE21C20681197A59DD54EE0A9C9
History When                    : 2009:07:30 14:22:54-07:00, 2009:07:30 14:22:54-07:00, 2009:07:30 14:25:10-07:00, 2009:07:30 14:46:43-07:00, 2009:07:30 14:47:13-07:00, 2009:07:30 14:52:54-07:00, 2009:07:30 14:53:22-07:00, 2009:07:30 14:54:13-07:00, 2009:07:30 14:56:56-07:00, 2009:07:30 14:58:50-07:00, 2009:07:30 14:59:10-07:00, 2009:07:30 14:59:19-07:00, 2009:07:30 15:01:58-07:00, 2009:07:30 15:02:25-07:00, 2009:07:30 17:22:58-07:00, 2009:07:30 18:58:17-07:00, 2009:07:30 18:58:29-07:00, 2009:07:30 18:59:25-07:00, 2009:07:30 19:03:31-07:00, 2009:07:31 08:21:27-07:00, 2009:07:31 08:23:10-07:00, 2009:07:31 08:38:17-07:00, 2009:07:31 08:38:43-07:00, 2009:07:31 08:40:48-07:00, 2009:07:31 08:41:54-07:00, 2009:07:31 08:45:06-07:00, 2009:07:31 08:54:33-07:00, 2009:07:31 08:59:26-07:00, 2009:07:31 09:03:16-07:00, 2009:07:31 09:09:19-07:00, 2009:07:31 09:12:35-07:00, 2009:07:31 09:18:15-07:00, 2009:07:31 09:19:05-07:00, 2009:07:31 09:19:40-07:00, 2009:07:31 09:24:06-07:00, 2009:07:31 09:39:03-07:00, 2009:07:31 09:39:21-07:00, 2009:07:31 09:40:12-07:00, 2009:07:31 09:41:16-07:00, 2009:07:31 09:42:05-07:00, 2009:07:31 10:38:45-07:00, 2009:07:31 10:57:21-07:00, 2009:07:31 11:00:53-07:00, 2009:07:31 11:01:35-07:00, 2009:07:31 11:05:38-07:00, 2009:08:02 07:18:42-07:00, 2009:08:02 07:20:51-07:00, 2009:08:02 07:23:40-07:00, 2009:08:02 07:38:52-07:00, 2009:08:02 07:40:06-07:00, 2009:08:03 17:30:11-07:00, 2009:08:03 17:31:43-07:00, 2009:08:03 17:34:23-07:00, 2009:08:03 17:36:09-07:00, 2009:08:03 17:37:35-07:00, 2009:08:04 15:07:45-07:00, 2009:08:04 15:08:32-07:00, 2010:01:07 09:52:28-08:00, 2010:01:07 09:52:28-08:00, 2010:01:07 09:53:53-08:00, 2010:01:07 10:48-08:00, 2010:01:07 10:52:30-08:00, 2010:01:07 10:54:03-08:00, 2010:01:07 10:57:23-08:00, 2010:01:07 11:00:17-08:00, 2010:01:07 11:03:03-08:00, 2010:01:07 11:03:48-08:00, 2010:01:07 12:41:57-08:00, 2010:01:07 12:41:57-08:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0
History Changed                 : /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /;/metadata, /, /, /, /, /, /, /, /, /metadata, /;/metadata
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 600.00, 600.00, 600.00, 600.00, 600.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 600.00, 600.00, 600.00, 600.00, 600.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:b9392b94-75ca-534c-9f07-ec50860debb3, uuid:4ac72fb0-2481-ce4e-9612-819b41a2b73e, uuid:4ac72fb0-2481-ce4e-9612-819b41a2b73e, uuid:7B3B7697DD3B11DB93B884F0724E0D1B, uuid:7B3B769FDD3B11DB93B884F0724E0D1B, uuid:7501649F096DDC11B04FCD96EA3864E4, uuid:B98EDC6DC8F111DB8FE0EE2B432BE2A4, uuid:EB21ADD8DD3B11DB93B884F0724E0D1B, uuid:dd74926c-cc5a-5746-b3aa-07bc19410155, uuid:1bbed826-0298-fe4b-9c45-9b4aa1932386, uuid:cd34c8d0-6a02-974f-b66d-61217524b5b1, uuid:b889a1fe-ea16-11db-bbea-000a958e60a8, uuid:f7e73746-ea1c-11db-bbea-000a958e60a8, uuid:112639f3-2ec7-b941-b0e1-2efdaa26052f, uuid:b9392b94-75ca-534c-9f07-ec50860debb3
Manifest Reference Document ID  : uuid:AEB1C89BDFC511DBA350E08D6C633A70, xmp.did:F77F117407206811A7918BE20EE67768, xmp.did:F77F117407206811A7918BE20EE67768, uuid:F88D649DCAD8DB118DEF8F99FE6474BA, uuid:BA36FB83E7D8DB118DEF8F99FE6474BA, uuid:083C48FBB7D8DB118DEF8F99FE6474BA, uuid:B98EDC6CC8F111DB8FE0EE2B432BE2A4, uuid:E7BECF4CC0D8DB118DEF8F99FE6474BA, xmp.did:018011740720681194578165994E99FE, xmp.did:028011740720681194578165994E99FE, xmp.did:038011740720681194578165994E99FE, uuid:2552B978CA4E11DBBBB8D4FD789DF739, uuid:2552B97BCA4E11DBBBB8D4FD789DF739, uuid:0F13725D8ECB11DB9C7BCA4243CC80C7, uuid:AEB1C89BDFC511DBA350E08D6C633A70
Doc Change Count                : 2836
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.0
Trapped                         : False
Page Count                      : 16
Creator                         : Adobe InDesign CS4 (6.0.4)

EXIF Metadata provided by EXIF.tools