Bluetooth Adater
FB200AS User Guide
Version 1.0
FIRMTECH Co., Ltd.
B-606, Ssangyong IT Twin Tower, Sangdaewon-dong, 442-5
Jungwon-gu, Seongnam-si, Gyeonggi-do, Korea 462-120
Tel : +82-31-719-4812
Fax : +82-31-719-4834
Inquiry : sales@firmtech.co.kr
www.firmtech.co.kr
FB200AS User Guide Version 1.0
Revision History
Revision History
Revision
Date
Ver 1.0
02-09-2009
Change Descriptions
- Write a draft
Page 2 / 28
FB200AS User Guide Version 1.0
(C) Copyright FIRMTECH Co., Ltd. 2005
(C) Copyright FIRMTECH Co., Ltd. 2005
All rights reserved
The products and operation descriptions contained herein shall be protected by
copyright law.
Any part or whole of products or operation description shall not be copied, reproduced,
translated, nor transformed into readable form by electronic device or machines, without
prior consent in writing by FIRMTECH Co., Ltd.
There might be some misprinting or technical faults in the products and operation
description which are subject to change without prior notice.
Page 3 / 28
FB200AS User Guide Version 1.0
List of Content
List of Content
1 What is Bluetooth? ...........................................................................................................................................................5
1.1 Features of Bluetooth ........................................................................................................................................5
1.2 Operation of Bluetooth .....................................................................................................................................5
2 Products Overview ...........................................................................................................................................................6
3 PRODUCT COMPONENTS .............................................................................................................................................7
3.1 Basic Components of FB200AS .....................................................................................................................7
4 Product Appearance ........................................................................................................................................................8
5 Features of Dip Switch ...................................................................................................................................................9
5.1 Dip Switch 1 (FUNCTION Switch) ................................................................................................................9
5.2 Dip Switch 2 (Baud Rate Switch)............................................................................................................... 10
5.3 Initial Set Value of Dip Switch .................................................................................................................... 10
6 Power Indicator LED / Status LED ......................................................................................................................... 11
7 Performance of Product ............................................................................................................................................. 12
8 Current Consumption .................................................................................................................................................. 13
9 Initial Set Value of Products ..................................................................................................................................... 14
10 Connecting the wireless section of Bluetooth ............................................................................................. 15
10.1 How to connect with Dip Switch Set-up ............................................................................................ 15
10.2 Connecting with Connection WIZARD................................................................................................. 15
11 How to complete PC Configuration? ................................................................................................................ 20
11.1 PC Configuration using BTConfig tool ................................................................................................ 20
11.2 PC Configuration using Serial Communication (Hyper Terminal) Program ..................... 23
12 Approval Information ................................................................................................................................................ 28
12.1 KCC ......................................................................................................................................................................... 28
12.2 FCC compliance Information..................................................................................................................... 28
12.3 CE ............................................................................................................................................................................ 28
12.4 TELEC ..................................................................................................................................................................... 28
12.5 SIG .......................................................................................................................................................................... 28
Page 4 / 28
FB200AS User Guide Version 1.0
1 What is Bluetooth?
1 What is Bluetooth?
1.1 Features of Bluetooth
Objectives of Bluetooth : To Realize Wireless Communication for Short Distance with Low Power
Consumption, High Reliability, and Low Cost.
Frequency in Use: To Use ISM(Industrial, Scientific, Medical) Band which does not require any
permission to use.
2.400 – 2.4835 GHz, 79 channels
2.465 – 2.4835 GHz, 23 channels (in France)
Transmission Rate : 1Mbps ~ 3Mbps
Transmission Output : 1mW (10m, Class2), 100mW (100m Class1)
Network Configuration : Configured with Master and Slave relation. A Bluetooth unit shall allow
simultaneous connections up to 7 devices (in case of ACL).
Reliability : To Guarantee stable wireless communication even under severe noisy environment
through adopting the technique of FHSS (Frequency Hopping Spread Spectrum).
1.2 Operation of Bluetooth
Bluetooth operates based on the connection between “Master” and “Slave”.
Masters are simply supposed to do “Inquiry” and “Page”. Slaves are supposed to do “Inquiry Scan”
and “Page Scan”.
If a Master finds a Slave and so “inquiry” is successful, a Slave responds to the Master with its
information.
Interconnection between the Master and the Slave is achieved only if the information from the
Slave is corresponded with the Master, and the Slave sends data to the Master.
Page 5 / 28
FB200AS User Guide Version 1.0
2 Products Overview
2 Products Overview
FB200AS has been developed to replace the previous RS232 Cable system with wireless communication
system to use.
Major Features of FB200AS
1.
Bluetooth Specification 2.0 Support
2.
Bluetooth Piconets(Point to Multipoint) are configurable up to (max. 1:7).
3.
Easy to control communication speed by using DIP Switch. (2400 bps – 230400bps)
4.
Support AT Command, and capable to control FB200AS by using AT Command.
5.
Easy to connect to use with Bluetooth PDA, Bluetooth USB Dongle, etc.
6.
Stable Data Transmission / Receipt
※ We request the new users of FB200AS to read the information on this description carefully before
they start to use the products.
Page 6 / 28
FB200AS User Guide Version 1.0
3 PRODUCT COMPONENTS
3 PRODUCT COMPONENTS
3.1 Basic Components of FB200AS
MODEL
PICTURE
FB200AS
Q’TY (EA)
(USB Serial Adapter)
WE-2405TO
(Dipole Ant)
CD
(Operation Manual and Test Program)
※ If you find any of above components is defective, or not included in the package, please contact the
seller you purchased.
Page 7 / 28
FB200AS User Guide Version 1.0
4 Product Appearance
4 Product Appearance
Page 8 / 28
FB200AS User Guide Version
1.0
5 Fe
eatures of Dip Switch
5 Fea
atures off Dip Sw
witch
B200AS Dip Sw
witch View>
5.1 Diip Switch 1 (FUNC
CTION Sw
witch)
SW
FEATU
URES
ON
OFF
BASIC SET
None
OFF
None
OFF
ROLE
MASTER
SLAVE
OFF
PC Configura
ation Mode
Operatiion Mode
OFF
Environment
Setting
(PC
Configura
ation Select)
Note :
If you push a Reset Swiitch when a Dip Switch iss turned ON in a PC Configuration Mode,
the
atus of FATOR
RY RESET.
products retturn to the sta
Page 9 / 28
FB200AS User Guide Version 1.0
5 Features of Dip Switch
5.2 Dip Switch 2 (Baud Rate Switch)
2400bps
4800bps
9600bps
19200bps
38400bps
57600bps
115200bps
230400bps
5.3 Initial Set Value of Dip Switch
TYPE
Function Switch
Baud Rate Switch
FB200AS
If the initial value is not consistent with
, please contact the seller you purchased the product.
Note :
If the CONNECTION MODE of PC Configuration is MODE4 (AT command language), it shall operate
based on the Baud rate and at the value of Role established in PC configuration, regardless of
setting of Baud rate and Role of Dip Switch.
Page 10 / 28
FB200AS User Guide Version
1.0
6 Power
Indicator LED / Sta
atus LED
6 Pow
wer Indiicator LE
ED / Sta
atus LED
FB200AS has a red Po
ower LED and green and re
ed Status LED. Please, refer to the follow
wing descriptio
on.
LED TYPE
STAT
TUS
DESCR
RIPTION
Power In
ndicator LED
Power Input
Red LED
D Turns on
(Power LED)
PC connected
Green LED
Turns on
Conn
necting to Blu
uetooth
Green LED
is Flickering
Conn
nected to Bluetooth
Green LED
turned on
PC Configuration
Red LED
D is Flickering
Status In
ndicator LED
(Status LED)
Note :
If you a Resset Switch when a red Sttatus LED flickers in a PC configuration Mode, the products
return to the
e status of FA
ACTORY RESET
T.
Pag
ge 11 / 28
FB200AS User Guide Version 1.0
7 Performance of Product
7 Performance of Product
No.
Part
Specification
Bluetooth Spec.
Bluetooth Specification 2.0 Support (EDR disabled)
Communication distance
100 M
Frequency Range
2402~2480MHz
Sensitivity
-83dBm (Typical)
Size
73 x 22 mm
Support Bluetooth Profile
SPP (Serial Port Profile)
Input Power
5V
Current Consumption
100mA
10
Temperature
Operating
-20℃ ~ 55℃
Limit Operating
-30℃ ~ 80℃
Communication Speed
1,200bps – 230,400bps
11
Antenna
Dipole Antenna
12
Interface
USB
13
Flow Control
RTS, CTS, DTR, DSR support
Page 12 / 28
FB200AS User Guide Version 1.0
8 Current Consumption
8 Current Consumption
STATUS
Current Consumption (mA)
MIN
MAX
AVG
Standby
18
24
22
Inquiry scan & page scan (Slave)
21
63
42
Page scan (Slave)
18
30
23
Inquiry (Master)
77
83
80
Slave
36
45
41
Master
21
33
27
Slave
48
54
51
Master
48
57
52
Slave
45
51
48
Master
45
54
49
Slave
48
57
52
Master
51
60
56
Slave
21
30
24
Master
21
33
24
Connected
Data transmission
Data reception
Data transmission / reception
Power save
TEST CONDITIONS
Baud rate : 9600 bps, Input Voltage : DC 5V
The power consumption is subject to change depending on the transmission rate and volume of data.
Page 13 / 28
FB200AS User Guide Version 1.0
9 Initial Set Value of Products
9 Initial Set Value of Products
The product has the initial Set Value as shown on the
.
Please be sure to identify the initial Set Value, before you begin to use.
TYPE
Set Values
Device Name
FB200v1.0
Pin Code (Pass key)
BTWIN
Uart (baud rate-data bit-parity bit-stop bit)
9600-8-N-1
ROLE
SLAVE
Connection Mode
MODE3
Operation Mode
MODE0 (1:1)
Debug Char
0x02
The Operating Set Values of Products is changeable by using Dip Switch or PC software (Window Hyper
Terminal, or FIRMTECH PC Configuration Program.)
Note :
Please refer to 11 PC Configuration for details on changing the setting.
Page 14 / 28
FB200AS User Guide Version 1.0
10 Connecting the wireless section of Bluetooth
10 Connecting the wireless section of Bluetooth
In order for Bluetooth devices to transmit data to each other, the wireless section of Bluetooth should be
connected to each other. To connect the wireless section, you should set each role for each device, one for a
Master, another for a Slave. It takes about 1~10 sec that a Master is connected to a Slave.
How to connect the wireless section of FB200AS can be performed with 2 significant ways.
Note :
The FB200 uses virtual COM port which shall be operated first before the Hyper Terminal is being
used so that the config tool shall be operable normally.
Please refer to the driver installation of Appendix FB200 for the instructions of driver installation of
FB200.
※ We will use 2 FB200AS and MS Windows in describing procedures.
10.1 How to connect with Dip Switch Set-up
FB200AS can perform data communication once you change the Dip Switch Set-up. The following is how to
set the Dip Switch.
(1) Set Baud rate Dip Switch of FB200AS(1) to the proper speed for communication
(2) Set FUNCTION Dip Switch #3 of FB200AS(1) to SLAVE.
(3) Turn the power of FB200AS(1) on.
(4) Set Baud rate Dip Switch of FB200AS(2) to the proper speed for communication.
(5) Set FUNCTION Dip Switch #3 of FB200AS(2) to MASTER.
(6) Turn the power of FB200AS(2) ON.
(7) If Status LED of FB200AS is turned on shortly, the wireless section of Bluetooth is properly
connected, so Data transmission can be performed.
10.2 Connecting with Connection WIZARD
(1) Connect FB200AS(1) to the USB port, and turn the power on.
(2) Execute C-Wizard Program.
Page 15 / 28
FB200AS User Guide Version 1.0
10 Connecting the wireless section of Bluetooth
(3) Click FIRMTECH SLAVE Set-up button ( Blue borders)
1 COM PORT : Select Serial port of PC connected a product.
2 DEBUG CHAR : Default is 0x02. (Refer to the appendix A about PC Configuration)
3 DEVICE COUNT : Select number of devices to be connected. (Default 1)
(4) Click the Set-up Start Button( Blue borders) after setting each values in blanks
( Red borders N.1 - Com Port connected to FB200AS, N.2 - 0x02, N.3 - 1)
Page 16 / 28
FB200AS User Guide Version 1.0
10 Connecting the wireless section of Bluetooth
1 Procedures: procedures of Device Set-up.
2 SLAVE Device value: It shows values if the SLAVE Set-up is completed (optional)
(5) Status Display of Procedures(N. 1 red borders) turns red into green after Set-up is
completed. Click the OK button if the blank of SLAVE Device Value is filled. (N. 2 red
borders)
(6) Connect FB200AS(2) to the USB port, and turn the power on.
(7) Click the FIRMTECH MASTER Set-up ( Blue borders) Button
Page 17 / 28
FB200AS User Guide Version 1.0
10 Connecting the wireless section of Bluetooth
1 COM PORT : Select the Serial port of PC connected a product
2 DEBUG CHAR : Default is 0x02. (Refer to the appendix A about PC Configuration)
(8) Click Set-up Start ( blue borders) button after setting each value ( red
borders N.1 - Com Port connected to FB200AS , N.2 - 0x02) in blanks.
(9) If the Status Display of Procedures ( N.1 red borders) turns red into green,
Connection Set-up is completed. With Clicking the End button( Blue borders), finish
the C-Wizard
Page 18 / 28
FB200AS User Guide Version 1.0
10 Connecting the wireless section of Bluetooth
(10) Set Function Dip Switch #3 to MASTER after turn the FB200AS(2)’s power off.
(11) The LED on Status LED of FB200AS(2) is turned ON shortly (It takes about 1 ~ 10sec) after the
power is turned on if the wireless section of Bluetooth is connected properly, and Data Transmission
is possible.
Page 19 / 28
FB200AS User Guide Version 1.0
11 How to complete PC Configuration?
11 How to complete PC Configuration?
The Baud rate or Role is selectable using Dip Switch. (In case, CONNECTION MODE is not MODE4.)
For other setting values, you can establish the setting using PC Configuration.
PC Configuration can be performed with two significant ways.
First is to use Configuration tool provided by FIRMTECH Co., Ltd.
Second is to use the serial communication programs such as Hyper Terminal or Mincom provided by OS.
The ways to configure are as follows respectively.
11.1 PC Configuration using BTConfig tool
(1) After setting 4th Switch (PC Configuration Switch) of Function Dip Switch FB200AS to ON, see if red
LED is flicker on Status LED by approving the power.
(2) Execute BTConfig tool after connect FB200AS to serial port of PC.
(3) Click “SERIAL OPEN” button. ( blue borders)
Page 20 / 28
FB200AS User Guide Version 1.0
11 How to complete PC Configuration?
1 DEBUG CHARACTER : Default is 0x02. (refer to the appendix A about PC Configuration)
2 SERIAL PORT : COM PORT proper port, BAUDRATE 9600, PARITY BIT None, STOP BIT 1
1 SERIAL OPENED, READ TO SET : BTConfig tool and communication status of products.
Page 21 / 28
FB200AS User Guide Version 1.0
11 How to complete PC Configuration?
(4) If the comes up, set each blank (Red borders N.1~2) to (COM PORT – Port
connected to Interface Board, BAUDRATE – 9600, PARITY BIT – None, STOP BIT – 1). After the setup, click the OPEN button (Red borders N.3), then Serial Connection and Ready To Set (Red borders
N.1) parts become green as shown on .
If they don’t become green, check the COM PORT and execute BTConfig tool once again.
(5) If click the READ button (blue borders) as shown on after BTConfig tool is connected
to products, MENU Buttons ( red borders N.1) are activated.
1 BLUETOOTH PARAMETERS: Set-up Group Button
2 Set-up window: change Set-up Groups and values
1 READ button: read set values. (READ should be done after BTConfig tool is connected to products at the
very first initialization.)
2 WRITE button: Save set values. (Serial port is automatically completed after saving.)
3 INIT button: Reset all the set values to Factory fix points.
(6) If you select any PARAMETERS( red borders N.1), the window for Value Check and
Set-up comes up on the right
(7) Save the set values by clicking the WRITE button after Set-up completed.
Page 22 / 28
FB200AS User Guide Version 1.0
11 How to complete PC Configuration?
1 WRITE PARAMETERS: Save the currently set values.
2 RETURN TO READ: Set to the initial value.
Note:
Please refer to the appendix A of PC Configuration for the detailed description.
11.2 PC Configuration using Serial Communication (Hyper Terminal)
Program
11.2.1 To Execute Hyper Terminal
To set up PC Configuration using Hyper Terminal, following procedures shall be performed prior to the
power is being supplied after the FB200AS is connected to the PC.
To set up PC Configuration, the Serial Communication Program is required. We will use Hyper Terminal in
describing the procedures.
(1) Fix the number 4 switch of Function Dip Switch at ON.
(2) Connect FB200AS to the USB port, and turn the power on.
Page 23 / 28
FB200AS User Guide Version 1.0
11 How to complete PC Configuration?
(3) Execute in the order of [start][All Programs][Accessories][Communications][Hyper
Terminal], then connection window will appear on which enter appropriate name and click.
(4) When the comes up, select the COM port connected to FB200AS, and clicks the OK
button.
Page 24 / 28
FB200AS User Guide Version 1.0
11 How to complete PC Configuration?
(5) When Registration Information Window comes up as on , select Bit per second :
9600, Data bit : 8, Parity : none, Stop bit : 1, Flow control : none, which will execute Hyper
Terminal.
Page 25 / 28
FB200AS User Guide Version 1.0
11 How to complete PC Configuration?
(6) (6) Basically, the Hyper Terminal does not show the entered character. To make sure of the entered
character, select [File][Properties] on the Menu, then registration information window will appear
shown as on , click the ASCII Setup button.
(7) As shown on , Check “Echo typed characters locally” and come out pressing the
acknowledge button. Now the Hyper Terminal program setting procedure is completed to use PC
Configuration.
(8) Press enter with small character "t" for FB200, the menu such as will appear on the
Hyper Terminal.
Page 26 / 28
FB200AS User Guide Version 1.0
11 How to complete PC Configuration?
11.2.2 How to Use PC Configuration Menu
The user may select the menu to change by selecting the given number in front of the left end menu.
For example : To change “DEVICE NAME”, enter : [1][Enter]
Note :
When Reset Button is pressed at , all the set up value shall be reset to the initial
set up status (factory fix point).
Following is the order to use the menu.
(1) The execution will only be executed by pressing the “Enter” key.
(2) The small character “t” will always move to be positioned at upper side of the menu.
(3) To move menu, use the number in the end of left side.
Please be sure to “Enter” key upon
completion of input.
(4) “←” key is used to delete the entered character currently.
(5) If the entered character is unreadable or is not supported at the appropriate menu, “Retry >”
message will be output.
(6) If the input message is more than 12 characters, “Overflow buffer” message will be output and then
“Retry >” message appeared as well.
Upon completion of PC Configuration setting up, turn off the FB200AS, and change the Function Dip
Switch #4 (PC configuration) to OFF position and turn the power ON, which will start the Bluetooth to
operate normally.
Note :
Please refer to the Appendix A, details of PC Configuration for detailed value description of PC
Configuration.
Page 27 / 28
FB200AS User Guide Version 1.0
12 Approval Information
12 Approval Information
12.1 KCC
12.2 FCC compliance Information
This device complies with part 15 of FCC Rules.
Operation is subject to the following two conditions:
1.
This device may not cause harmful interference received.
2.
This device must accept any interference received.
Including interference that may cause undesired operation.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this
Equipment may cause harmful interference unless the modifications are expressly approved in
the instruction manual. The user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to Part 15 of the Federal Communication Commission(FCC) rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and , if not installed and
used in accordance with the instructions, may cause harmful interference to radio communication.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
antenna.
Reorient or relocate the receiving
Increase the separation between the equipment and the receiver.
Connect the
equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/television technician for help.
12.3 CE
Hereby, Firmtech Co., Ltd, declares that this FB200AS is in compliance with the essential
requirements and other relevant provisions of directive 1999/5/EC.
12.4 TELEC
12.5 SIG
Page 28 / 28
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.5
Linearized : No
Author : Administrator
Create Date : 2009:09:11 08:09:27+09:00
Modify Date : 2009:09:11 14:32:18+09:00
XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool : PScript5.dll Version 5.2.2
Metadata Date : 2009:09:11 14:32:18+09:00
Format : application/pdf
Title : Microsoft Word - FB200AS_V10Eng_20090909_최종메뉴얼수정_.docx
Creator : Administrator
Producer : Acrobat Distiller 9.0.0 (Windows)
Document ID : uuid:179580dc-fa72-4954-b0c3-9265ffbd9a39
Instance ID : uuid:d4470467-a11e-43ba-aa40-83ee56ddbb11
Page Count : 28
