First Computer A440 NOTEBOOK COMPUTER User Manual A440 English Manual PDF

Download:
Mirror Download [FCC.gov]
Document ID	124495
Application ID	mDs5P1dLEcUQIAwvOX/1jg==
Document Description	user manual 2 of 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	64.55kB (806919 bits)
Date Submitted	2000-11-07 00:00:00
Date Available	2000-11-03 00:00:00
Creation Date	0000-00-00 00:00:00
Producing Software	Acrobat PDFWriter 3.02 for Windows
Document Lastmod	2000-11-07 08:53:47
Document Title	A440 English Manual, PDF
Document Creator	Microsoft Word
Document Author:	FIC Lester

otebook User Guide
Fun with Multimedia
his chapter lets you make full use of all the
multimedia features of your computer in having fun
learn how to mix and match the built-in sound
system, CD-ROM or DVD-ROM, and ZV port
presentation.
81
N
otebook User Guide
4.1
Notebook Multimedia Features
Your notebook computer is rich in multimedia features that makes your
computing fun, comfortable, exciting and easy. Exceeding the specification set
for the Multimedia Personal Computer or MPC, your computer is well able to
perform all multimedia tasks through the following:
4.2
•
Intel Mobile Pentium !!!/Intel Mobile Celeron
•
32MB RAM or more
•
24X-Speed CD-ROM Drive or 8X DVD-ROM Drive (option)
•
32bit AGP 2X VGA Graphics Controller
•
16-bit Plug-and-Play Audio Sound System with built-in speaker and
microphone
•
ZV Port Capability (for MPEG cards)
Audio Sound System Features
Your computer has a built-in 16-bit stereo sound controller that allows you to
record, store, and playback voice, music and other sound effects with built-in
mixer controls. An integrated full-duplex microphone and twin mini-speakers
are also built-in into your computer to allow you to record and playback
sound anytime and anywhere.
On the front of your computer, you will find the audio ports that include the
following:
•
82
External 1/8-inch microphone jack that supports full-duplex monophonic
mode or half-duplex stereo mode
otebook User Guide
Earphone or headphone jack for personal listening
Line-out jack for connecting external amplified speakers, headphones, or
•
tape deck or synthesizer
•
4.3
External thumb-wheel volume control
Properties
Before you can start using the audio capabilities of your computer, you need
bought your computer with Windows pre-installed, it is most likely that your
dealer have configured the sound driver for you. If not, you must refer to
4.4
Windows Multimedia Programs
built-in features of your computer. The Multimedia programs group is found
by clicking the Start button, then pointing to Programs, then Accessories, and
83
N
otebook User Guide
Figure 4-1
Multimedia Programs Group
The standard multimedia components are as follows:
•
External volume control buttons
•
CD Player - for playing audio compact discs
•
Media Player - for playing sound video and animation files
•
Sound Recorder - for recording sounds and playback
•
Volume Control - for adjusting the volume of mixer
+ For more information on how to operate these multimedia components,
run the program and click on the Help menu.
4.5
Recording Sounds
Your computer allows you to record voice and other sounds in several ways
and stores them as files on your hard disk. These voice or sound files can then
be played back through the internal speaker or external line-out and earphone
jack using either an external speaker, headphone, or earphone set. You can
also use the files as voice annotations on many applications for more real
84
otebook User Guide
under Windows operating system.
To record sounds, you need to run the Sound Recorder program from the
simple to understand which comprises of the Rewind, Forward, Play, Stop,
and Record button. Click the Help menu on how to operate the Sound
Figure 4-2 Sound Recorder
The Sound Recorder also allows you to record sound from different input
audio source like the following:
•
From the built-in microphone
•
From the external microphone
•
From the CD-ROM drive
•
From the Line-In audio jack
Since you could record sound from different input sources, you must first set
the proper audio input recording device under the Recording Control panel.
To do this:
85
N
otebook User Guide
1.
then point to Programs, Accessories, Multimedia, and then click on
Volume Control.
Click Options and Properties.
Click the round button for Recording and select to show all volume
Figure 4-3
Audio Volume Properties
N
otebook User Guide
4.
Click OK and the Recording Control dialog box will appear. Here, you
will select the input device for the recording source. The default is the
microphone which will record sound from the microphone only. If you
want to record from the CD-ROM drive with audio music, you must
click on CD Audio.
Figure 4-4
Recording Volume Control
USING THE BUILT-IN MICROPHONE
You would normally use the microphone for recording voice and save the file
for voice annotations in your application programs. Your computer comes
with a built-in microphone located on the front side of your computer.
To start recording from the built-in microphone:
1.
Enable microphone volume on the Recording Control as discussed
previously.
2.
Run the Sound Recorder program and press the Record button.
3.
Start to speak towards the built-in microphone and press the Stop button
when you want to stop recording.
87
N
otebook User Guide
4.
5.
USING AN XTERNAL M
Your computer also allows you to connect an external microphone for higher
quality recording. The external microphone jack is found on the front side of
connected. Use only microphone with 1/8-inch mini-jack connector. Follow
CD-ROM/DVD-ROM D
You would normally use the CD-ROM drive for recording audio music from
1.
Activate CD Audio volume on the Recording Control as discussed
2.
Run the Sound Recorder program.
the CD auto-insertion notification for supporting Suspend mode, the CD
disc and will start playing the audio CD.
N
otebook User Guide
Figure 4-5 CD Player
5.
Set the starting point where you want to start recording.
6.
Switch to the Sound Recorder and press the Record button.
7.
Switch immediately to the CD Player and press the Play button. You can
adjust the volume control so you can also hear the recording.
USING AN EXTERNAL AUDIO INPUT DEVICE
You can also record sound from an external audio device such as stereo
amplifier or tape recorder by connecting them to the Line-In audio jack
Use the same procedure as above by setting the Recording Control to enable
the line-in volume. Run the Sound Recorder and press the Record button.
Start playing the external audio device to begin recording.
89
N
otebook User Guide
4.6
Playing Audio and Sound
Your computer has a built-in twin speaker to playback audio and sound. You
can also adjust the volume manually by adjusting the thumb-wheel volume
control found on the front side of your computer.
For more quality sound output, you can choose to connect an external
amplified speaker that connects to the Line-out jack on the front of your
computer. You can also connect earphone or headphone set. Always minimize
the volume first before placing the phone set to your ear.
USING THE MEDIA PLAYER
The easiest way to playback multimedia media files is to run the Media Player.
Follow these steps:
90
1.
Click on Start, then point to Programs, Accessories, and Multimedia.
2.
Click on Media Player to start program.
N
otebook User Guide
Figure 4-6
Media Player
3.
Click on the Device menu to select the sound device type you want to
play or you can directly open the file on the File menu.
4.
When the file is recognized and open, click on the Play button to start
playback.
5.
For playing audio CD, it is better to run the CD Player as discussed
earlier.
91
N
otebook User Guide
4.7
Playing Video and MPEG Files
Your computer is capable of running video motion files as well as MPEG
(Motion Picture Expert Group) files on CD or DVD. By using a software
MPEG program, you can watch real full-motion picture on your computer.
You can also run the ActiveMovie Player under the Multimedia programs
group or the Media Player as well to show all media device programs.
4.8
Using PC Cards with ZV Port
Although running software MPEG programs allows you to watch movies and
video CD, the quality and speed is still not at par when watching motion
picture on TV or movie theaters. Your computer is equipped with the latest
ZV port technology that dramatically speeds up video playback. By inserting a
ZV port-capable MPEG PC card into the PCMCIA slot, you can watch
smooth full-screen motion picture just like in TV or at the movies. Consult
your dealer on how to get a ZV port MPEG card and read the card user
manual for installation.
4.9
Using DVD
DVD is the latest breakthrough in superb full-motion picture playback. One
disc can contain at least 4.7GB of information, capable of holding one fulllength movie with soundtracks, subtitles, and different languages. Much more,
the DVD-ROM drive of your computer is backward compatible with CDROM drive so it allows you to use any CD as well. It also works the same as
the CD-ROM.
92
N
otebook User Guide
To playback DVD titles, you would need a MPEG-2 compatible PCMCIA
card or software MPEG-2 program and the optional DVD-ROM Device
Pack.
For software MPEG-2 program, the performance in media playing will be
implemented successfully only when this computer is complied with Intel
Pentium II - 266MHz CPU or above. Otherwise, any computer that equipped
under Intel Pentium II - 266MHz CPU can not guarantee the performance in
media playing.
MPEG-2 cards provide audio and video jack, so you can connect it to your
wide-screen TV for the best home entertainment. Consult your dealer for
more information.
93
N
otebook User Guide
94
N
otebook User Guide
Connecting to Peripherals
This chapter describes how you attach peripheral
devices to your notebook. You can attach a printer
or mouse, connect an external monitor and
keyboard, or any other peripheral device. You will
learn how to use these peripheral devices with the
step-by-step instructions depicted in this chapter.
95
N
otebook User Guide
5.1
Using a Serial Mouse
Your computer has one 9-pin male serial port for connecting an external serial
mouse, printer or modem. The serial (RS232) port of your computer is
normally referred to as COM1. When working with your computer on the
desktop, you may want to use an external serial mouse instead of the Glide
Pad. If you want to use a modem as well, we recommend using a
voice/fax/modem PC card through the PCMCIA slot.
+ When you connect a printer, be sure to install the appropriate printer
driver through the Windows Control Panel.
To install an external serial mouse:
96
1.
Turn off your computer.
2.
Plug the serial mouse connector to the serial port at the back of your
computer. Secure the connection with the screws provided.
3.
Turn on the computer.
4.
Click the Start button, then point to Settings, and click Control Panel
when there is another mouse connects to PS/2 port.
N
otebook User Guide
5.2
5.
Double-click on the Add/Remove Program icon to appear the Add
New Hardware Wizard.
6.
Follow the relative steps when screen shows up to guide you in executing
the specific procedures.
7.
When system has rebooted, Windows will automatically detect the serial
mouse.
Using an External Keyboard (PS/2)
At the back of your computer, you will find the 6-pin mini-DIN PS/2
keyboard and mouse port. This port allows you to connect an external fullsized PS/2 desktop keyboard as well as an external PS/2 mouse. It is
recommended to use an external PS/2 mouse only if you are not using an
external PS/2 keyboard. Otherwise, you must use the serial port for
connecting a serial mouse as discussed earlier. If you want to use both the
external PS/2 mouse and keyboard, you would need to buy a PS/2 Y-cable.
You can also purchase a keyboard adapter from your computer dealer that
allows you to connect standard 5-pin DIN-type desktop keyboards. This type
of keyboard is widely used by desktop computers compared to PS/2 type.
To connect the external keyboard:
1.
Turn off your computer.
2.
Connect the PS/2 keyboard directly to the PS/2 port. If you are using 5pin DIN-type keyboard, plug the keyboard to the keyboard adapter first
and then to the PS/2 port. Windows 95/98 keyboard are also supported.
3.
Turn on your computer. Both the built-in keyboard and the external
keyboard are active and can be used simultaneously.
97
N
otebook User Guide
+ Do not disconnect or connect the external keyboard when power is on.
Turn off the computer first. You can connect an external keyboard or
keypad only while the system is in Suspend mode.
+ If you connect an external mouse, you must re-boot the system.
To connect an external PS/2 mouse, follow the same procedure as above.
Both the PS/2 mouse and the built-in Glide Pad will work at the same time.
5.3
Using the USB Port
USB or Universal Serial Port is a peripheral bus standard developed by
Compaq, DEC, IBM, Intel, Microsoft, NEC and Northern Telecom. Personal
computers equipped with USB will allow computer peripherals to
automatically configure as soon as they are physically attached - without the
need to reboot or run setup. USB will also allow multiple devices to run
simultaneously on a computer, with peripherals such as digital cameras,
scanners, printers, CD-ROM drives, modems, keyboards, telephones, games
devices and monitors acting as additional plug-in sites, or hubs.
USB devices called USB hubs can serve as connection ports for other USB
peripherals. Only one device needs to be plugged into your notebook
98
N
otebook User Guide
computer. Additional peripherals can be connected in a daisy chain
configuration where one device is connected to another in a series.
Windows 95 B version (OSR 2.1 release) or later version will come equipped
with the drivers that allows your PC to recognize USB peripherals.
+ Depending on your operational requirements, you may need to disable the
USB port in order to release system resources to use other devices.
5.4
Connecting a Parallel Printer
The parallel (LPT1) port has a 25-pin female connector at the back of your
computer. You would always connect to this whenever you are going to print
out to a parallel printer.
To connect to a printer:
1.
Connect the printer to the parallel port using the 25-pin male connector
cable of the printer. Secure the cable with the screws provided.
2.
Align and connect the other end of the cable to the parallel port on the
device. Lock the connector clips.
3.
Connect the power cable to the device and a properly grounded wall
outlet.
4.
Power on both computer and printer.
5.
Check the printer by doing a self-test operation.
6.
Set the printer type of your software to recognize the connected printer.
99
N
otebook User Guide
7.
If your printer is not listed in the software you are using, consult your
printer dealer for available drivers or any compatible ones.
8.
Press the Online function of the printer.
+ When you connect a printer, be sure to install the appropriate printer
driver through the Windows Control Panel.
+ Check that the device is online before you try to use it. See the
instructions that came with the device for more information.
5.5
Using an External Monitor (VGA Port)
Your computer has a 15-pin VGA port for supporting any external VGA
color monitor with maximum display resolution of 1024x768 64K colors or
32-bit true colors. You need a display signal cable (usually provided with the
monitor). One end of the cable must have a 15-pin connector for the system.
To connect an external monitor:
1.
Turn off your computer and make sure the monitor power switch is
turned off.
+ The notebook computer must be powered off or suspended while the
monitor is being connected.
100
N
otebook User Guide
2.
Connect the connector cable of the monitor to the VGA port at the back
of your computer. Secure the cable connection with the screws provided.
3.
Connect the monitor power cable and plug it into a properly grounded
wall outlet.
4.
Turn the power of the monitor.
5.
Turn on your computer. Both the LCD panel and the monitor screen will
show the display. Your computer is set at default to run at simultaneous
display mode.
6.
If you only want to show the display on the monitor (CRT) and shut off
the LCD display, you can use the  +  hot-key to switch
display type between LCD and CRT. Keep pressing the hot-key until you
get the display to CRT only.
+ Refer to Chapter 3 regarding the possible VGA resolutions and how to
change the display properties.
5.6
Using the SIR Port (Optional)
Your computer is equipped with an industry standard IR port that allows
enhanced wireless connection with infrared built-in devices like PDAs,
101
N
otebook User Guide
electronic organizers, printers, and portable computers. The IR port is
Infrared Data Association (IrDA) compatible which makes use of the second
COM port or COM2 of your computer. The transfer rates for SIR (Serial
Infrared Standard) is 115.2Kbit/sec.
To connect to another IR equipped device:
1.
Properly position both your computer and the target device. Place the
target device in line with your notebook and should be within 80cm (30inches) from each other. You should refer to the User
Guide of the
target device on how to enable its IR function.
2.
Turn on your computer and run the BIOS Setup program. Go to the
Advanced menu and set the Infrared Port to Enabled.
+ Your notebook computer ships with the IR port disabled. The first time
that you use the IR port, you must enable the device through the setup
utility.
102
3.
After setting up both devices to enable IR function, run the application
you wanted to use the IR port.
4.
Set the transmission protocol or device to COM2. Make sure that this
does not conflict with any pre-installed fax/modem PC card which is also
configured at COM2.
N
otebook User Guide
5.7
Using the TV Port
Also found at the back of your computer is one S-Video port.
To display your computer screen on the TV:
1.
Turn off your computer and plug one end of the S-Video jack cable to
the end to the input video jack of your television set.
2.
Turn on your computer and your television set.
3.
Click the Start button, then point to Settings, and click Control Panel.
4.
Double-click on the Display icon and point to Setting tab.
5.
Double-click Advanced button and point to Displays tab.
6.
Choose the TV button then click OK. Windows now automatically detect
the TV port and enable this function.
103
N
otebook User Guide
5.8
Using the External Audio System
At the front of your computer, you will find the built-in audio ports. You can
connect audio input jacks with microphone and stereo device; and audio
output jack with external speakers, earphone, or headphone for recording and
playing sound.
To connect to a audio jack:
1.
Locate the audio port (Microphone, Line-in or Headphones) that you
want to use to the target device.
2.
Plug the jack into the port on the front side of the system.
+ Some audio device cable connectors are designed with an icon
representative of the device. When connecting the audio device to your
notebook computer, be sure to match the icon on the cable connector to
the icon on the system port.
+ If you use external speakers and experience the sound distortion or
feedback, please lower the volume. Some factors is caused by too close
locating the microphone and speakers from each other, moving away the
external audio option from the unit may also help.
104
N
otebook User Guide
105
N
otebook User Guide
Customizing Your Notebook
Your computer uses the Phoenix BIOS Setup
program that allows you to set several system
configuration in changing the way your computer
performs. This includes your system time and date,
disk drive configuration, password setup, and power
management settings. These information are then
stored in the CMOS RAM and will remain
permanent unless you change it again. This chapter
discusses on how you will activate the BIOS Setup
program and change the system configuration to suit
your desired operation. You must be careful to set
the configuration properly in order for your
computer to run smoothly. If you are not sure of any
settings, contact your dealer.
106
N
otebook User Guide
6.1
Running the BIOS Setup Program
Your computer is likely to have been properly setup and configured by your
dealer prior to delivery. However, you may find it necessary to use the
computer’s BIOS (Basic Input-Output System) Setup program to change
system configuration information, such as the current date and time, or your
hard disk drive type. The Setup program can be accessed when you power on
the system and pressing the  function key.
The settings that you specify within the Setup program are recorded in a
special area memory called the CMOS RAM. This memory is backed up by a
battery so that is will not be erased when you turn off or reset the system.
Whenever you turn on the computer, the system will read the settings stored
in the CMOS RAM and compare them to the equipment check conducted
during the Power On Self Test (POST). If an error occurs, an error message
will be displayed on the screen, and you will then be prompted to run the
Setup Program.
As the POST (Power-On Self Test) executes during the boot up process, the
screen will display the following message:
Press  to Enter SETUP
Press the  key to run the BIOS Setup program. The BIOS Setup
program is organized into six menus which you can select using the ß and à
keys. To move from one option to another, you use the up and down arrow
keys while using the <+> and <-> keys to change the settings. On the right
hand side of the screen are some brief help descriptions of each item you
want to change.
On the BIOS Setup program, you will find the following parts on the screen:
107
N
otebook User Guide
•
Item Specific Help
The right side of the screen. This area describes each parameter and its
available settings. The BIOS is subject to change without previous notice,
so the description here can help you to select the best parameters.
•
Menu Bar
The top line of the screen. Each of the six selections displays its own
screen.
•
Parameters
The left side of the screen. This area lists the parameters and their current
settings.
•
Key Status Bar
The bottom part of the screen. These lines display the keys available to
move the cursor, select a particular function and so forth.
To exit the BIOS Setup program, simply press the  key and select from
the Exit menu whether you want to Save changes and exit; Discard Changes
and exit; or Set default values.
108
N
otebook User Guide
6.2
Using the Main Menu Setup
PhoenixBIOS Setup Utility
Main
Advanced
Security
APM Mode
Boot
Exit
Item Specific Help
System Time:
[12 :00 :00]
, ,
System Date:
[07/01/1999]
or  selects
Language:
[English (US)]
field.
Diskette A:
[1.44/1.25 MB, 3½”]
Primary Master
[12073MB]
Secondary Master
[CD-ROM]
Boot Display Device:
[LCD+CRT]
Memory Cache
[Disabled]
System Memory:
640 KB
Extended Memory:
130048 KB
CPU Type:
Pentium (R) III
CPU Speed:
700 MHz
BIOS Version:
0.3B-5702-6211/2319192C
F1 Help
áâ
Select Item
−/+
Esc Exit
ßà
Select Menu
Enter Select 4 Sub-Menu F10 Save and Exit
Change Values
F9
Setup Defaults
109
N
otebook User Guide
110
•
System Time
Allows you to change the system time using the hour:minute:second
format of the computer.
Enter the current time for reach field and use the ,
+, or  key to move from one field or back to
another.
You can also change the system time from your operating system.
•
System Date
Allows you to set the system date using the month/date/year format.
Your notebook is year 2000-compliant.
Enter the current time for reach field and use the ,
+, or  key to move from one field or back to
another.
You can also change the system time from your operating system.
•
Language
Allows you to set the display language in English or Japanese version for
the BIOS Setup program.
•
Diskette A
This item enables or disables the floppy disk drive by pressing the
 key. When you select 1.44MB/1.25MB 3 ½”, you should know
that the 1.25MB 3 ½” diskette requires a 3-mode floppy-disk drive and
refers to a 1024byte/sector Japanese media format.
•
Primary Master
This field displays various parameters for the hard disk drive. If type
[Auto] is selected, the system automatically sets these parameters. If type
[User] is selected, Cylinders, Heads and Sectors and its access mode can
be edited.
N
otebook User Guide
•
Secondary Master
This field displays various parameters for the second hard disk drive or
CD-ROM or DVD-ROM. Some of these fields are for information only
as the BIOS automatically detects and adjust the parameters.
•
Boot Display Device
Lets you select the display device.
•
Memory Cache
Lets you enable or disable the RAM to work as cache. Enable it can
speed up the access time but reduce the RAM that software can use.
•
System Memory
This field reports the amount of base (or conventional) memory found by
the BIOS during Power-On Self-Test (POST).
•
Extended Memory
This field reports the amount of extended memory found by the BIOS
during Power-On Self-Test (POST).
•
CPU Type
This field reports the CPU type information detected by the BIOS during
Power-On Self-Test (POST).
•
CPU Speed
This field reports the CPU speed information detected by the BIOS
during Power-On Self-Test (POST).
•
BIOS Version
This field are for information only as the BIOS display the BIOS version
during the Power-On Self-Test (POST).
111
N
otebook User Guide
6.2.1 INTERNAL HDD SUB-MENU
PhoenixBIOS Setup Utility
Main
Primary Master: [12073MB]
Type:
Item Specific Help
[Auto]
User = you enter
CHS format
parameters of hard-
Cylinders:
[16383]
disk drive installed
Heads:
[16]
at the Connection.
Sectors:
[63]
Auto = autotypes
12073MB
Hard-disk drive
Maximum Capacity:
LBA format
installed here.
Total Sectors:
21733140
None = no device is
Maximum Capacity:
12073MB
installed here.
Ultra DMA Mode:
[Mode 4]
ROM drive is
Transfer Mode:
[Fast PIO 4]
installed here.
Multi-Sector Transfers:
[16 Sectors]
LBA Mode Control:
[Enabled]
32 Bit I/O:
[Disabled]
CD-ROM = a CD-
F1 Help
áâ
Select Item
−/+
Esc Exit
ßà
Select Menu
Enter Select 4 Sub-Menu F10 Save and Exit
Change Values
F9
Setup Defaults
Use the Type field to select the drive type installed. You can select different
drive types as CD-ROM, User, or None by pressing  bar. Set this
option to Auto so your computer will automatically detect the drive type
during power on. Set this option to None when your computer is not installed
any devices. Press  to return to the Main Menu. Move the
112
N
otebook User Guide
6.3
Using the Advanced CMOS Setup
PhoenixBIOS Setup Utility
Main
Advanced
Security
APM Mode
Boot
Exit
Item Specific Help
CPU Frequency
[100Mhz]
‘Disabled’ prevents any
DRAM Frequency
[100Mhz]
installed PS/2 mouse
BootUp Num-Lock
[LockOff]
frees up IRQ12.
PS/2 Mouse:
[Both]
‘Enabled’ allows the
LCD Panel View Expansion:
[Enable]
operating system to
Summary Screen
[Enable]
determine whether
Silent Boot:
[Disabled]
to enable or disable
Save to Disk Warning
[Enable]
the mouse
Installed O/S
[Win98/Win2000]
AGP-2X Mode
[Enabled]
Aperture Size
[64M]
Frame Buffer Size
[8 MB]
from functioning, but
I/O Device Configuration
On Chip Multi-function Device:
Advanced Chipset Control
F1 Help
áâ
Select Item
−/+
Esc Exit
ßà
Select Menu
Enter Select 4 Sub-Menu F10 Save and Exit
Change Values
•
CPU Frequency
Shows the internal running frequency of CPU.
•
DRAM Frequency
Shows the running frequency of DRAM.
F9
Setup Defaults
113
N
otebook User Guide
114
•
BootUp Num-Lock
Lock or unlock the Num-Lock key after the system is bootup.
•
PS/2 Mouse
[Enabled] allows the OS to determine whether to enable or disable the
PS/2 mouse. [Disabled] prevents any installed PS/2 mouse from
functioning.
•
LCD Panel View Expansion
Expand or keep the original LCD Screen View during the boot
procedure. Expand may get full screen display of LCD, however, it affect
the graphic/text quality
•
Summary Screen
Display system configuration on boot
•
Silent Boot
Lets you specify the boot screen as Logo screen, POST screen, or Black
screen by choosing Enabled, Disabled, or Black option, respectively.
•
Save to Disk Warning:
Display warning message when the Save to Disk file (save2dsk.bin) does
not exist. This file is used when you shot down your computer to suspend
mode.
•
Installed O/S
Select the operation system which is installed on this computer. An
incorrect setting may cause unexpected behavior.
•
AGP-2X Mode
Please use default value. If it needs any change, please contact system
supervisor.
•
Aperture Size
Please use default value. If it needs any change, please contact system
supervisor.
N
otebook User Guide
•
Frame Buffer Size
Please use default value. If it needs any change, please contact system
supervisor.
•
I/O Device Configuration
Lets you configure input/output device such as Serial Port, Infrared Port,
Parallel Port, and Floppy disk controller.
•
On Chip Multi-function Device:
Lets you configure Audio, sound device, Joystick and Modem… internal
device.
•
Advanced Chipset Control:
The advance setting of chipset. If it needs any change, please see its Item
Specific Help and contact system supervisor to do that.
6.3.1 PERIPHERAL SUB-MENU
PhoenixBIOS Setup Utility
Advanced
I/O Device Configuration
Item Specific Help
Serial port:
[Auto]
Configure serial port A
Infrared port:
[Disabled]
using options:
Parallel port:
[Auto]
[Disabled]
Mode:
[Bi-directional]
Floppy disk controller:
[Enable]
Local Bus IDE adapter
[Both]
No configuration,
[Enabled]
User configuration,
[Auto]
BIOS or OS chooses
Configuration,
115
N
otebook User Guide
116
F1 Help
áâ
Select Item
−/+
Esc Exit
ßà
Select Menu
Enter Select 4 Sub-Menu F10 Save and Exit
Change Values
F9
Setup Defaults
•
Serial port
You can press  to select the Enabled, Disabled, or Auto option
for enabled or disabled the port, or automatically sensed the address
assignment by BIOS or OS. When you set the configured Serial port to
Enabled rather than Auto, you should also set the parameter of Base I/O
address and IRQ for this port.
•
Infrared port
Lets you press  to select the Enabled, Disabled, or Auto option
for enabled or disabled the port, or automatically sensed the address
assignment by BIOS or OS. When you set the configured Serial port to
Enabled rather than Auto, you should also set the parameter of Base I/O
address and IR mode for this port.
•
Parallel port
Allows you to press  to select the Enabled, Disabled, or Auto
option for enabled or disabled this port, or automatically sensed the
address assignment by BIOS or OS.
•
Mode
Allows you to press  to select a parallel mode as Output only,
Bi-directional, or ECP when the parallel port is configured. When you set
the configured parallel port to Enabled rather than Auto, you should also
set the parameter of Base I/O address and IRQ for this port.
•
Floppy disk controller
Allows you to press  to select the Enabled or Disabled option
for configured or not configured the floppy disk controller.
N
otebook User Guide
•
Local Bus IDE adapter
Allows you to press  to enabled or disabled primary or
secondary IDE adapter.
6.3.2 CHIP MULTI-FUNCTION SUB-MENU
PhoenixBIOS Setup Utility
Advanced
On Chip Multi-Function Device
OnChip USB Device:
[Enabled]
Item Specific Help
Enabled/Disabled
Function 2
Onboard Legacy Audio:
[Enabled]
Sound Blaster:
[Disabled]
MPU-401 :
[Disabled]
FM Port :
[Enabled]
Joystick:
[Enabled]
Modem Device:
[Disabled]
USB Port 0-1
F1 Help
áâ
Select Item
−/+
Esc Exit
ßà
Select Menu
Enter Select 4 Sub-Menu F10 Save and Exit
•
Change Values
F9
Setup Defaults
This manu lets you enable or disable certain internal device.
6.3.3 ADVANCE CHIPSET CONTROL SUB-MENU
PhoenixBIOS Setup Utility
Advanced
117
N
otebook User Guide
Advance Chipset Control
SDRAM PC-133 support
[No]
Enabled/Disabled
SDRAM Cycle Latency
[Enabled]
Function 2
SDRAM Bank Interleave:
[Enabled]
USB Port 0-1
System Shadow:
[Disabled]
Video Shadow:
[Disabled]
Cache Video BIOS area:
[Enabled]
PCI Delay Transaction
[Enabled]
Read-around-Write:
[Disabled]
Concurrent PCI Master/Host
[Enabled]
AGP Master 0 WS Write:
[Enabled]
AGP Master 0 WS Read:
[Enabled]
F1 Help
áâ
Select Item
−/+
Esc Exit
ßà
Select Menu
Enter Select 4 Sub-Menu F10 Save and Exit
•
6.4
Item Specific Help
Change Values
F9
Setup Defaults
You can set the setting here to default value to make sure that the system
work normally. However, you can change certain setting to improve
performance. Please see its Item Specific Help to know more about that.
Security Menu Setup
PhoenixBIOS Setup Utility
Main
118
Advanced
Security
APM Mode
Boot
Exit
N
otebook User Guide
Item Specific Help
Supervisor Password Is
[Clear]
Supervisor Password
User Password Is
[Clear]
controls access to the
Set Supervisor Password:
[Enter]
Set User Password:
[Enter]
Password on boot:
[Disabled]
Fixed disk boot sector:
[Normal]
Diskette access:
[Supervisor]
setup utility.
F1 Help
áâ
Select Item
−/+
Change Values
Esc Exit
ßà
Select Menu
Enter
Select 4 Sub-Menu F10 Save and Exit
F9
Setup Defaults
•
Supervisor Password Is
Set/Clear selections show that the notebook is under controlled by
Supervisor Password or not.
•
User Password Is
Set/Clear selections show that the notebook is under controlled by User
Password or not.
•
Set Supervisor Password
Supervisor password gives you the authority in accessing the setup utility.
You can also enter the supervisor password in booting the system and
resuming from suspend mode. When you press  in this field,
the Set Supervisor Password dialog box appears. Enter a new password
with up to 8 alpha-numeric characters, and then enter this same new
password again for confirmation.
119
N
otebook User Guide
120
•
Set User Password
This field is only available when you have set Supervisor Password
previously. You can enter the user password when boot the system or
resume from suspend mode. But if you set Write Protect in the Fixed
disk boot sector field, you should enter a supervisor password to access
the fixed disk when boot the system or resume from suspend mode.
•
Password on Boot
If you set this field to Enabled, your computer will always ask for the
password every time you boot your computer.
•
Password on Resume
If you set this field to Enabled, your computer will always ask for the
password every time when you resume from your computer.
•
Fixed Disk Boot Sector
If you set this field to Write Protect, the write protect boot sector on
hard disk will protect against viruses. In this situation, only the supervisor
can access this fixed disk.
•
Diskette Access
If you set this field to Supervisor, only the supervisor can access to the
diskette drives. If you set to User, both the supervisor and user can
access to the diskette drives.
N
otebook User Guide
6.5
Using Power Saving Setup
PhoenixBIOS Setup Utility
Main
Advanced
Security
APM Mode
Boot
Exit
Item Specific Help
Power Switch:
[On/Off]
Behavior of the
Lid Switch
[BL On/Off]
Power switch.
Power Management Function
[Battery only]
‘Suspend/Resume’
Power Savings
[Disabled]
causes the PC to
Suspend Mode
[Suspend]
Suspend/Resume,
Idle Mode:
[Off]
Standby Timeout:
[Off]
‘On/Off’ causes the
Auto Suspend Timeout:
[Off]
PC to Power
Auto Save To Disk:
[Off]
On/Off.
Hard Disk Timeout:
[Disabled]
Video Timeout:
[Disabled]
Please be noticed
that all the Power
Resume On Modem Ring:
[Off]
menu settings will
Resume On Time:
[Off]
be ineffective in
the ACPI mode.
F1
Help
Esc Exit
•
á â Select Item
−/+
Change Values
F9 Setup Defaults
ß à Select Menu Enter Select 4 Sub-Menu F10 Save and Exit
Power Switch
The power button operates as both an On/Off and Suspend/Resume
button.
121
N
otebook User Guide
On/Off functions as a normal power switch to power the system on
or off.
ß
Suspend/Resume functions as a suspend button to put the system
into Suspend mode and return to normal operation from Suspend.
•
Lid Switch
The system goes into "Suspend/Resume" mode or "Back light On/Off"
mode when the LCD panel is closed when the system is still running.
•
Power Management Function
Lets you set up power management by the system power source. You can
select Always On or Battery Only. If you choose Always On, various
power saving modes will function to save the power source both from
AC power and battery power. If you choose Battery Only, power saving
function will only execute for battery pack.
•
Power Savings
Lets you choose one of four levels of power management.
•
122
ß
ß
Diabled
turns off the power management function.
ß
Customized
alter these settings of power saving.
ß
Maximum Power Savings
conserves the greatest amount of system power.
ß
Maximum Performance
conserves power but allows the greatest system performance.
Suspend Mode
When the Power Switch is set to "Suspend/Resume", When you power
off the notebook, it goes into "Suspend" or "Save to Disk" mode
N
otebook User Guide
ß
Save to Disk
The system will save its state to disk and power off.
ß
Suspend
The system will save its state but remain in a low power mode.
•
Idle Mode
Turn on the Idle Mode can slow down the CPU during brief periods
when the system is not busy for power saving.
•
Standby Timeout
Lets you specify the amount of time before the system entering the
Standby Mode. Standby Mode powers off various devices in the system,
until you start using the computer again. You can choose Off, 1, 2, 4, 6,
8, 12, or 16 minutes in this field.
•
Auto Suspend Timeout
Lets you specify the amount of time before the system entering the
Suspend Mode. Suspend Mode powers off various devices in the system,
except the memory component, until you start using the computer again.
You can choose Off, 5, 10, 15, 20, 30, 40, or 60 minutes in this field.
•
Auto Save To Disk
Lets you turn on or off the Auto Save To Disk feature. If you turn on it,
the system will save its state to disk and then power off after being in
Suspend mode for 1 hour.
•
Hard Disk Timeout
Allows you to select the amount of time that your hard disk is not active
before it shuts down. You can specify the amount of time as 1, 2, 4, 6, 8,
10, 15, 30, 45 minutes, or choose Disabled to inactive this feature.
123
N
otebook User Guide
124
•
Video Timeout
Allows you to select the amount of time that your input devices are not
active before your video shuts down. You can specify the amount of time
as 1, 2, 4, 6, 8, 10, 15, 30, 45 minutes, or choose Disabled to inactive this
feature.
•
Resume On Modem Ring
Lets you specify On or Off to wake up the system or not, when an
incoming call is detected on your modem. If the Suspend Mode field is
set to Save To Disk, the Resume On Modem Ring field will not work.
•
Resume On Time
Lets you specify On or Off to wake the system up at a specific time or
not. If the Suspend Mode field is set to Save To Disk, the Resume On
Time field is disabled.
N
otebook User Guide
6.6
Using the Boot Setup
This item allows you to set the search drive sequence where the system will
try to boot up first.
PhoenixBIOS Setup Utility
Main
Advanced
Security
APM Mode
Boot
Exit
Item Specific Help
+Removable Devices
Use <á> or <â> to
+Hard Drive
select a device, then
ATAPI CD-ROM Drive
press <+> to move it
up to the list, or <-> to
move it down to the
list. Press  to
exit from this menu.
F1 Help
á â Select Item
−/+
Esc Exit
ß à Select Menu
Enter Select 4 Sub-Menu
Change Values
F9
Setup Defaults
F10 Save and Exit
To select the boot device, you can use the up or down arrow key, then press
<+> to move up the device in the list or press <-> to move down the device
in the list. To exit from this menu, press .
125
N
otebook User Guide
6.7
How to Exit the Setup Program
There are three choices to escape from the Setup program.
PhoenixBIOS Setup Utility
Main
Advanced
Security
APM Mode
Boot
Exit
Item Specific Help
Exit Saving Changes
Exit System Setup
Exit Discarding Changes
and save your
Load Setup Defaults
changes to CMOS.
Discard Changes
Save Changes
Battery Refresh
126
F1 Help
á â Select Item
−/+
Esc Exit
ß à Select Menu
Enter Execute Command
Change Values
F9
Setup Defaults
F10
Save and Exit
•
Exit Saving Changes
This option saves all changes to CMOS while running the BIOS setup
program and exit from the system setup program.
•
Exit Discarding Changes
This options allows you to discard all changes made while running the
BIOS setup program and exit from the system setup program.
•
Load Setup Defaults
This option lets you load the default values for all setup items.
•
Discard Changes
Reverts to previously selected settings.
N
otebook User Guide
6.8
•
Save Changes
Saves Setup data to CMOS.
•
Battery Refresh
Conditions the battery so that the battery can be fully charged. The
function applies to NiMH battery only.
How to Upgrade the BIOS
Your computer uses EPROM Flash BIOS chip that allows you to easily
upgrade the BIOS program. When you update the BIOS, any customized
settings you made are lost.
To upgrade the BIOS:
1.
Insert the BIOS Update diskette into the diskette drive.
2.
Power on the system with the diskette in the diskette drive.
3. On the DOS prompt, type the following command.
A:\>Phlash XXXXXX.ROM (BIOS filename)
4.
Press  to run this BIOS utility. After the system has been
successfully run this program, a message similar to the following appears:
Flash memory has been successfully programmed,
press any key to restart the system. If the
system does not restart, turn it off, then turn
on again.
5.
Press any key to restart this system.
Contact your dealer for the latest BIOS update file.
127
N
otebook User Guide
Using Options
This chapter describes the most advanced features
and expandable architecture in your notebook. With
the optional internal modem and LAN module, you
can easily execute each function only by connecting
the cable to the modem or LAN port. You can also
upgrade your memory size or configure the PortBar
to your system for specific requirements.
128
N
otebook User Guide
7.1
LAN Module Option
This notebook comes with an optional internal 10Base-T/100Base-TX LAN
module that connects your computer to other computers/networks through a
local area network (LAN) and supports data transfer rates at 10Mbps and can
be up to 100Mbps. The 10Base-T standard also called Twisted Pair Ethernet
is connected with RJ-45 connectors. The 100Base-TX is based on the older
Ethernet standard. Because it is 10 times faster than Ethernet, it is often
referred to as Fast Ethernet.
CONNECTING THE INTERNAL LAN MODULE
The built-in LAN module provides a standard RJ-45 connector. We provide
you a twisted-pair cable for your convenience.
To connect the twisted-pair cable to your LAN port:
7.2
1.
Locate the twisted-pair cable in the accessories box in notebook shipping
carton. Each end of the cable has a RJ-45 connector.
2.
Connect one end of the cable into the network wall outlet or HUB.
3.
Connect the other end of the cable into the computer RJ-45 LAN port.
Modem Module Option
This notebook comes equipped with a 56K internal voice/fax/data modem
that allows you to communicate with others via fax, email, or to connect to an
online service or bulletin board. The modem module is available as an option.
129
N
otebook User Guide
CONNECTING THE INTERNAL MODEM
The built-in voice/fax/data modem provides on standard phone connector.
We provide you one analog cable for your convenience.
To connect the analog phone cable to your modem:
1.
Locate the analog phone cable in the accessories box in notebook
shipping carton. Each end of the cable has a RJ-11 connector.
2.
Connect one end of the cable into a standard wall outlet.
3.
Connect the other end of the cable into the computer modem port.
+ The speed of data transmission is dependent on the quality of telephone
lines. Digitally terminated lines improve the speed of data transmission.
Contact your service provider for more information.
+ The analog phone cable is an industry standard cable. Longer cables are
available at your local electronics store.
7.3
PortBar Option
This notebook system provides a PortBar option for your convenience to
accommodate your necessity. Keep the PortBar connected to peripherals in
your office while you take your notebook computer on the road.
+ If the model you had purchased does not has the optional PortBar port, it
is also not available for this PortBart option.
130
N
otebook User Guide
FEATURES OF THE PORTBAR
The PortBar is an accessory that duplicates the ports found on the back of
your notebook computer.
The ports on the PortBar are described as follows:
¶. AC Power Port
·. Mini-DIN PS/2 Mouse Port
¸. Mini-DIN PS/2 Keyboard Port
¹. Serial Port
º. Parallel Port
». Monitor Port
¼. USB Port
PortBar
•
AC Power Port
Connects an AC adapter to your notebook computer.
•
Mini-DIN PS/2 Mouse Port
Connects to a PS/2 mouse.
•
Mini-DIN PS/2 Keyboard Port
Connects to a 6-pin standard PS/2-style keyboard.
131
N
otebook User Guide
•
Serial Port
Connects a serial device to your notebook computer, such as an external
modem or mouse.
•
Parallel Port
Connects a printer to your notebook computer. You can change the LPT
Mode in the BIOS Setup program.
•
Monitor Port
Connects an external VGA/SVGA monitor to your notebook computer.
•
USB Port
Connects up to 127 peripheral devices to your notebook computer.
CONNECTING THE PORTBAR TO YOUR SYSTEM
An optional PortBar was developed to work specifically with your notebook
computer.
Follow these steps to install the optional PortBar:
132
1.
Rotate the release bars to the outside.
2.
Plug the PortBar into the expansion connector on the back of the
notebook computer. Make sure that the PortBar firmly snaps into the
PortBar latches on each side of the notebook computer.
3.
Rotate the release bars to the center to lock.
N
otebook User Guide
¶. Release bars
¸. PortBar latches
·. PortBar
Using PortBar
7.4
System Upgrade
This section provides an easy step in doing system upgrades for your
notebook computer. The upgrade procedures includes the following:
MEMORY UPGRADE PROCEDURE
Your notebook computer offers two 64-bit memory slots using 144-pin
SODIMM (Small Outline Dual Inline Memory Module) at least 32MB, 64MB
and 128MB SDRAM. The memory compartment is located just under your
computer.
133
N
otebook User Guide
Based Memory
Installing Memory
Total
32 MB
0 MB
32 MB
32 MB
32 MB
64 MB
32 MB
64 MB
96 MB
32 MB
128 MB
160 MB
64 MB
0 MB
64 MB
64 MB
32 MB
96 MB
64 MB
64 MB
128 MB
64 MB
128 MB
192 MB
128 MB
0 MB
128 MB
128 MB
32 MB
160 MB
128 MB
64 MB
192 MB
128 MB
128 MB
256 MB
INSTALLING MEMORY MODULE
Your computer comes with standard 32 or 64MB of synchronous DRAM
(SDRAM). You can increase system memory to a maximum of 256 MB in the
system, by installing one small outline double inline memory modules (SODIMMs) with installed base memory in the system.
The 32MB memory module, 64MB memory module, and 128MB memory
module are available:
To install the memory module:
134
1.
Make sure the system is powered off and that no peripheral devices are
attached.
2.
Turn the system over and locate the screw that secure the DIMM door at
the underside of the notebook.
N
otebook User Guide
3.
Remove the screw and open the DIMM cover by lifting its upper side.
4.
Locate the alignment notch on the module.
5.
Locate the memory module sockets. (Your system comes with one
module already installed in the socket.)
+ Avoid touching the exposed components inside the system. Doing so may
damage the system.
6.
Align the notch with the notch in the socket connector and insert the
module as follows:
Ÿ Hold the SO-DIMM at a 30-degree angle and align the SO-DIMM
connector with the socket in the system. Push the connector into
the socket.
Ÿ Press down on the edge of the SO-DIMM until the locking tabs on
the sides snap into place, securing the module.
7.
Replace the DIMM door and secure the screw at the DIMM door.
8.
Turn the system over.
To remove a SODIMM, press the locking tabs away from the sides of the
module until the module pops up. Then, remove the SODIMM.
135
N
otebook User Guide
136
N
otebook User Guide
137
N
otebook User Guide
Caring for Your
Notebook
Your Notebook PC is a fully IBM compatible
portable personal computer with the latest features in
mobile computing and multimedia technology.
Lightweight and compact, your Notebook PC runs
on a whole wide range of general business, personal
productivity, and professional applications, it is ideal
for use in the office, at home, and on the road.
Your Notebook PC also allows you for several levels
of customization and expansion that are previously
available only on desktop PCs.
138
N
otebook User Guide
8.1
Important Safety Instructions
Portable computers take the most beating from end users. This section gives
you detailed information about how to maintain a safe working environment
while using the notebook computer. You can maintain its condition and
performance by following these guidelines. Please read it carefully to ensure
maximum safety.
•
Before cleaning the notebook computer, make sure it is disconnected
from any external power supplies (i.e. AC adapter, car adapter and so on).
•
When cleaning, do not use liquid or sprayed detergent for cleaning.
Instead, use moisture sheet or a cloth for cleaning.
•
The socket-outlet shall be installed near the notebook computer and shall
be easily accessible.
•
Please keep the notebook computer from humidity.
•
Lay the notebook computer on a reliable surface when installing. A drop
or fall may cause injury.
•
The openings on the enclosure are for air convection hence the notebook
computer can be protected from overheating. DO NOT COVER THE
OPENINGS.
•
Be careful of using power supply. The notebook computer has specific
power requirements.
•
Use only a power adapter approved for use with this notebook computer.
•
The power adapter may have a 2-prong plug. This is an important safety
feature. A compatible outlet is required. If it is not available, find a
qualified electrician to install one.
139
N
otebook User Guide
140
•
While unplugging the power cord, disconnect it by the plug head, not by
its wire.
•
Make sure the socket and any extension cords you may use can support
the total current load of all the connected devices.
•
Though your AC adapter is suitable for universal international voltage, it
still requires a stable and continual power supply. Make sure the voltage
of the power source when connect the notebook computer to the power
outlet. If your are unsure of your local power specifications, consult your
dealer or local power company.
•
Place the power cord in such a way that people can not step on it. Do
not place anything over the power cord.
•
All cautions and warnings on the notebook computer should be noted.
•
If the notebook computer is not in use for a long time, disconnect it from
mains to avoid possible damage by transient over-voltage.
•
Never pour any liquid into openings as this may cause fire or electrical
shock.
•
Never open the body of notebook computer. For safety reason, the
notebook computer should only be opened by qualified service
personnel.
•
If one of the following situations arises, have the notebook computer
checked by service personnel:
ß
The power cord or plug is damaged.
ß
Liquid has penetrated into the notebook computer.
ß
The notebook computer has been exposed to moisture.
ß
The notebook computer has not worked well or you can not get it
work according to user’s manual.
N
otebook User Guide
ß
The notebook computer has dropped and damaged.
ß
The notebook computer has obvious sign of breakage.
•
Do not leave this notebook computer in an environment unconditioned.
Storage temperature above 60ºC (140ºF) may damage the notebook
computer.
•
An approved power cord has to be used for the notebook computer’s
power supply. For a rated current up to 6A and an equipment weight
more than 3 kg, a power cord not lighter than H05VV-F, 2G, 0.75mm2,
has to be used.
•
To avoid any damage happened to the internal device, you should first
disconnect the AC adapter and remove the battery pack from the
notebook when replacing any internal device.
The sound pressure level at the operators position according to IEC 60704-1
is equal or less than 70dB(A).
8.2
Cleaning Your Computer
When it is necessary to clean the plastic case and keyboard, use a soft, lint-free
cloth, slightly dampened with a mild detergent solution or use the contents of
any commercially available computer cleaning kit.
Never use alcohol, petroleum-based solvents, or harsh detergents to clean the
notebook. Also never spray any liquids directly on the computer case,
keyboard, or screen. If the liquid-crystal display (LCD) screen has become
smeared or dusty, clean the screen by first applying a mild glass cleaner to a
soft, clean, lint-free cloth, and gently wipe the glass. Never apply liquids
141
N
otebook User Guide
directly on the screen surface. Moreover, do not use paper towels to clean the
display screen. Paper can scratch the display screen matte.
8.3
Maintaining the LCD Quality
When it comes to screen problems, heat plays a big part. After a good working
session, the typical routine is to shut the machine and close the cover. But the
display surface - no matter what type it is - and the components inside the
computer radiates heat; when you close the cover, you trap the heat against
the screen. Leave the computer's cover open for about ten minutes while the
heat disperses. Make this a habit.
You should also enable the power management of your computer to turn off
the LCD power and display when the system is in inactivity for some time.
Adding screen savers is also acceptable.
Follow the safety guidelines mentioned earlier and how to clean your
computer.
8.4
Maintaining Your Hard Disk
Losing your data has the same consequences as a system break down. Users
must make it a habit of doing hard disk maintenance every week or so. Here is
some maintenance you could do:
142
•
Always back up your data files from your hard disk.
•
Install a virus detecting program to monitor virus that could tamper your
files.
•
Use SCANDISK once in a while to correct any errors found in the
directory and File Allocation Table (FAT). This will also free up space
from any unused sectors.
N
otebook User Guide
8.5
•
Never move or raise the computer while the hard disk is being accessed,
most especially don't jar the hard disk as this may cause a hard disk crash.
•
Use hard disk maintenance programs like DEFRAG or Norton Utilities
SPEEDISK. These reorganize your hard disk by eliminating
fragmentation and improving your hard disk access time.
•
Install a system password in your computer so others won't be able to use
the hard disk.
Battery Care Guidelines
The battery pack furnished with the computer requires reasonable care and
handling to ensure efficient operation and maximum life. There is a risk of
fire and chemical burn if the battery pack is handled improperly.
To ensure that the battery pack endures normal life cycle, always observe the
following precautions when handling the battery pack:
•
Handle batteries carefully. Do not try to disassemble, crush, puncture,
open, drop, mutilate , short external contacts, disposed of in water or fire,
or expose it to temperatures higher than 60 C.
•
Recharge batteries only as described in this manual and only in ventilated
areas. Never use an external charger other than the one supplied with
your computer.
•
Do not leave batteries in hot locations for more than a day or two.
•
Do not leave your battery in your computer for longer than a week
without plugging in the power adapter.
•
Do not leave battery in storage for more than 6 months without
recharging it.
143
N
otebook User Guide
8.6
•
Dispose dead battery properly to protect the environment. The batteries
contain hazardous chemicals and should not be thrown out with
household or office trash.
•
Discharge completely the battery before recharging to improve battery
performance.
When You Travel
For safety and convenience when traveling, please follow these instructions:
144
•
Back up all needed files on your hard disk before traveling.
•
Recharge your battery overnight to ensure full battery power before you
leave.
•
Don't forget to bring along the AC adapter and extra battery pack.
•
Try to bring backup software as well.
•
Check the voltage rating and the outlet type of your destination. If the
power cord of the adapter is different, then you need to purchase a
suitable one. Consult your dealer.
•
Carry your computer in its carrying case or in a briefcase. Never check-in
the computer as a luggage.
•
Remember to apply those power saving features and techniques to save
battery power.
N
otebook User Guide
145
N
otebook User Guide
APPENDIX A
Hardware System Information
This appendix gives information on the technical
and hardware specifications of your computer. Please
note that the information mentioned here may not be
exactly the same with your computer as specification
is subject to change without notice or modifying this
manual.
Designed with an advanced modular architecture,
your Notebook PC also allows you for several levels
of customization and expansion that are previously
available only on desktop PCs.
146
N
otebook User Guide
A.1 System Specification
PROCESSOR UNIT
•
Intel Pentium !!!/Celeron FC-PGA Socket 370
•
Supports CPU clock speed above 500MHz
•
256KB integrated L2 cache for Pentium !!!/ 128KB integrated L2 cache
for Celeron
SYSTEM MEMORY
•
Two 64-bit 144-pin memory slots
•
User-upgradable to maximum 256MB using 144-pin SODIMM 32MB,
64MB, and 128MB module
•
PC100 SDRAM modules
LCD DISPLAY
•
XGA (1024x768) or SVGA (800x600) Color LCD
•
Maximum 32 bit true colors on all LCD display
VGA SYSTEM
•
32-bit AGP Local Bus VGA Accelerator (32-bit internal)
•
Includes Zoomed Video (ZV) Port Technology for supporting ZV
PCMCIA cards
147
N
otebook User Guide
•
Simultaneous LCD and external monitor (CRT) display
•
Maximum 16 million colors on CRT only display at 800x600 resolution
(Non-Interlaced)
•
Maximum 1024x768 resolution on CRT display at 16M colors
DISK DRIVES
•
32-bit PCI Enhanced IDE interface with LBA mode
•
24X-speed Enhanced IDE bootable CD-ROM drive module
•
Built-in and upgradable 2.5-inch IDE hard drive
•
Optional DVD-ROM drive that can be swapped with CD-ROM
AUDIO SYSTEM
•
Full-duplex 16-bit stereo audio with wavetable support and Plug-and-Play
features
•
H/W Audio Sound Blaster 16 compatible
•
Built-in dual speakers
•
Integrated full-duplex microphone
•
Audio input jacks for microphone (MIC) and stereo device (Line-In)
•
Audio output jack for external speaker or headphone (Line-Out)
•
Earphone or headphone jack for audio output
•
Built-in Thumb Wheel Volume Control
PCMCIA
•
148
32-bit CardBus PCI Local Bus PCMCIA controller
N
otebook User Guide
•
Double-deck PCMCIA slots supports 2 x Type II PC card at the same
time or 1 x Type III PC Card
•
Supports Zoomed Video (ZV) Cards, 32-bit Cardbus Cards, and 16-bit
PC Cards
GLIDE PAD
•
Integrated Glide Pad (PS/2 mouse) pointing device with palm-rest typing
surface
KEYBOARD
•
Full-sized 86/87-keys keyboard with Windows 95/98 hot-keys, inverted
T-cursor keys, 12 function keys, and embedded numeric keypad
•
Provides international language keyboard
FLASH BIOS
•
512K Flash ROM BIOS for easy BIOS upgrade
I/O PORTS
•
2 x Universal Serial Bus (USB)
•
1 x 9-pin RS-232 Serial (COM1)
•
1 x 25-pin Parallel (LPT1)
•
1 x 15-pin VGA (CRT)
•
1 x S-Video TV port
•
1 x PS/2
149
N
otebook User Guide
INFRARED PORT (OPTIONAL)
•
1 x SIR port at 115.2Kbps
AC/DC POWER SUPPLY ADAPTER
•
Universal auto-switching 65W (100V~240V) adapter
BATTERY
•
Rechargeable 8 Cells NiMH or Li-ion battery pack with Smart Battery
function
•
Over 2 hours of usage (when run Battery Mark2.0 diagnostic program)
•
2.5 ~ 3.5 hours quick charge (computer turn off)
WEIGHT AND DIMENSION
•
12” (W) x 9.8” (D) x 1.5” (H)
•
6.6 lbs (Max Target)
A.2 IRQ Usage Summary
150
IRQ#
Description
IRQ 0
System Timer
IRQ 1
Keyboard
IRQ 2
[Cascade]
IRQ 3
Lan/Modem
IRQ 4
Serial Port 1
N
otebook User Guide
IRQ 5
Audio/VGA/USB
IRQ 6
Floppy Disk Drive
IRQ 7
Parallel Port
IRQ 8
RTC Alarm
IRQ 9
ACPI
IRQ10
LAN/MODEM
IRQ11
Reserved for PCMCIA card
IRQ12
PS/2 Mouse
IRQ13
FPU
IRQ14
Hard Disk Drive/LS120
IRQ15
CD-ROM or DVD
A.3 DMA Channel Usage Summary
ISA DMA Map:
DMA Channel
Device
DMA 0
Unused
DMA 1
ECP
DMA 2
Floppy Disk
151
N
otebook User Guide
152
DMA 3
AUDIO
DMA 4
[Cascade]
DMA 5
Unused
DMA 6
Unused
DMA 7
Unused
N
otebook User Guide
153

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Creator                         : Microsoft Word
Create Date                     : 2000¦~9¤ë21¤é 04:09:12 PM
Title                           : A440 English Manual, PDF
Author                          : FIC Lester
Producer                        : Acrobat PDFWriter 3.02 for Windows
Subject                         : 
Modify Date                     : 2000:11:07 08:53:47-08:00
Page Count                      : 73

EXIF Metadata provided by EXIF.tools