Fisher And Paykel Nz Au Bi602Cte Users Manual 541768C_BIcombo_INST

BI602ED to the manual 802323d6-914d-1464-bd6e-219d578df4d9

2015-02-02

: Fisher-And-Paykel Fisher-And-Paykel-Nz-Au-Bi602Cte-Users-Manual-406213 fisher-and-paykel-nz-au-bi602cte-users-manual-406213 fisher-and-paykel pdf

Open the PDF directly: View PDF PDF.
Page Count: 8

541768C 10.2004 NZ
BI602 series
Built-In Oven
Installation Instructions
NZ, AU Installation Information
BI602ED series
Built-In Double
Oven
BI602CTE series
Built-In Oven/Cooktop combination
BI602XC series
Built-In Oven/
Microwave
combination
BI452 series
Built-In Compact
Oven
1
Warnings and Safety information
CAUTION!
In order to avoid hazard these products
must be installed according to these
instructions.
Please follow installation information
carefully. If in doubt consult your local
building authority by-laws.
Failure to install the product correctly
could invalidate any warranty or liability
claims.
The product is to be installed only by an
authorised person.
IMPORTANT!
Please make this information available to
the person responsible for installing the
product as it could reduce your installation
costs.
The cavity must be a completely sealed
box with no gaps. This will ensure the
cooling air flows under the product and
through the oven frame to give the correct
venting and cooling for the oven and
cabinet surround. Failure to seal cavity
box may cause distortion of surrounding
cabinetry.
Read these instructions carefully before
installing or using this product.
Before you start
Ensure a suitable disconnection switch
is incorporated in the permanent wiring,
mounted and positioned to comply with
the local wiring rules and regulations. A
means of disconnection with at least a
3mm air gap contact separation in all poles
must be incorporated into the fixed wiring
in accordance with the wiring rules, unless
the local wiring rules allow for the following
variation. A means of disconnection from
the supply having an air gap separation
in all active (phase) conductors must be
incorporated in to the fixed wiring.
Ensure that the location of the oven
connection socket is outside the installation
space if the product is flush to the rear wall.
Ensure the benchtop and the oven cavity are
square and level.
Ensure the electrician provides sufficient
free length of mains cable to reach from the
bottom rear of the cavity to at least 1.5 metres
in front of the bottom edge of the opening.
The cable may enter the cavity from the side,
top or bottom, but top entry must be at the
rear of the cavity.
Use easy to clean finishes for the wall surfaces
surrounding the oven and cooktop to aid
in removal of any cooking fume staining
resulting from the use of the oven and
cooktop.
Check the height from the floor suits the user.
Ensure that drawers and doors will be clear of
obstruction when fully opened.
WARNING!
Cut Hazard
Take care - panel
edges are sharp.
Failure to use caution
could result in minor
injury or cuts.
2
Installation Instructions
Flush fitting installation options
c
b
a
20 mm
2.5 mm
20 mm
2.5 mm
20 mm
2.5 mm
CUPBOARD FRONT
DRAWER FRONT
Installation instructions
1
Check that the oven cavity is square
and within the limits in the installation
dimensions.
2
Remove the mains wiring access cover.
3
Connect the mains wiring and replace the
access cover.
4
Remove the oven door and accessories, lift
and slide oven into place. When installing
the oven it is essential to centre the product
in the cavity giving a spacing of 2.5mm from
the door edge to the joinery
5
Secure oven in cavity using the four ‘wood
screws’ and washers supplied through the
enamelled frame at either side of the oven as
shown in the flush fitting installation options.
6
Test then refit the door and accessories,
check that the oven is firmly secured in the
kitchen unit.
Installing a cooktop above an oven
If installing a cooktop above the oven ensure
adequate clearance is provided for the
cooktop as per the Cooktop Manufacturers
Instructions.
3
Height recommendation guide
Figures are based on an average height of 1650mm (5’5”) wearing shoes. The height of the
product may vary according to the height of the most frequent user.
4
600 mm
585 mm
600 mm
20 mm
570 mm MIN
16-20 mm
922 mm
600 mm
Top View
600 mm
20 mm
570 mm MIN
16-20 mm
Top View
460 mm
oven door562 mm
20 mm
595 mm
578 mm
595 mm
550 mm
550 mm
595 mm
932 mm
460 mm
upper door
315 mm
lower door
20 mm
562 mm
915 mm
BI602 series Single Built-In Oven BI602ED series Double Built-In Oven
5
BI602CTE series Built-In Oven/Cooktop
Combination
1
Remove the brackets from the cooktop.
2
Place the cooktop in the cutout and secure
using the brackets previously removed.
3
Feed the cooktop wiring harness out
through the oven cavity.
4
Remove the oven connector block cover on
the oven top wiring cover.
5
Connect the cooktop wiring harness lining
the numbers/letters on the harness with
the numbers/letters on the oven connector
block. Leave plastic wiring card attached for
future reference.
6
Clamp the wiring harness with the wiring
clamp on the oven top wiring cover.
7
Replace the oven connector block cover.
8
Install the oven as described on page 2.
Cooktop Installation
54PNEEN321
54PNEEN321
harness detail
oven connector
block
plastic
wiring card
600 mm
585 mm
Benchtop Detail
600 mm
20 mm
570 mm MIN
16-20 mm
Top View
460 mm
oven door562 mm
20 mm
595 mm
578 mm
595 mm
550 mm
Benchtop
CookTop Cutout* 20 mm
Gap
15 mm
MIN.
55 mm
MIN.
OVEN
*see cooktop installation
instructions p/n 599100
6
BI602XC series Built-In Oven/Microwave
Combination
BI452 series Compact Built-In Oven
440 mm
600 mm
935 mm
600 mm
595 mm
70 mm min.
clearance
600 mm
20 mm
570 mm MIN
16-20 mm
Top View
600 mm
20 mm
570 mm MIN
16-20 mm
Top View
315 mm
oven door562 mm
20 mm
450 mm
433 mm
595 mm
550 mm
560 mm
930 mm
562 mm
20 mm
460 mm
oven door
932 mm
microwave
door
465 mm
595 mm
455 mm
30 mm

Navigation menu