Fisher Price DPV70-01 Bluetooth Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3441957
Application ID	GjIjXs1FVR90WWEHXob9WQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	17.11kB (213850 bits)
Date Submitted	2017-06-28 00:00:00
Date Available	2017-06-28 00:00:00
Creation Date	2017-06-28 14:13:52
Producing Software	Acrobat Distiller 9.3.3 (Windows)
Document Lastmod	2017-06-28 14:13:52
Document Title	Microsoft Word - UserManual06.16?(revised?on?June?26).doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	05368

WMD410A01MT6A0 (HY-254101M) Use TTC2541 /TI CC2541 IC chip
24 pin BLE Bluetooth module (with shield case) specifications.
1. Dimensions
（1-1）.DIMENSION SIZE :
PCB SIZE：
15.2*25.3*1.0 mm
PCBA with shield
case Tickness：
2.6mm
(1-2):
FCC ID & IC ID Laser Print Format on the Shield Case :
1 st row:
2 nd row:
3 rd row:
M/N : HY-254101M
FCC ID : CCT-DPV70-01
IC : 4390A-DPV70
2. Module pin definition and description of input and output ports
（2-1）HY-254101C（WMD410A01MA6A0 PCB Antenna）pin map
（2-2）Pin function table (Not shown in the I/O pin functions ,Please see
Table (3-3) input and output ports description)
Pin
No.
Function
Function
IO2_2 / DC
Digital I/O port 2_2
IO2_1 / DD
Digital I/O port 2_1
IO2_0
Digital I/O port 2_0
Description
/ Debug clock
Debug data
Digital I/O port 1_7
IO1_7 / SEL1 MCU communication mode select, See table(5-3)
Communication protcol mode selection, I/O setting Table
Digital I/O port 1_6
IO1_6 / SEL0 MCU communication mode select, See table(5-3)
Communication protcol mode selection, I/O setting Table
IO3_1 /
Digital I/O port 3_1
I2C
SCL
IIC serial Clock (SCL)
can be used as I2C clock pin or digital I/O. Leave floating
if not used. If grounded disable pull up
IO1_5
Digital I/O port 1_5
IO1_4 / PWM4 Digital I/O port 1_4
/ PWM port 4
IO1_3 / PWM3 Digital I/O port 1_3
/ PWM port 3
10
IO1_2 / PWM2 Digital I/O port 1_2
/ PWM port 2
Digital I/O port 3_0
11
IO3_0 / I2C
SDA
I2C serial Data (SDA)
Can be used as I2C data pin or digital I/O. Leave floating
if not used. If grounded disable pull up
12
GND
13
VCC
BLE module grounding pin
BLE module power supply pin,
voltage range of 2.0 ~ 3.6V
Digital I/O port 1_1
14
IO1_1 / PWM1 / PWM port 1
Digital I/O port 1_0
15
16
17
18
19
20mA drive capability
20mA drive capability
IO1_0 / PWM0 / PWM port 0
IO0_7
Digital I/O port 0_7
ADC7
ADC port 7
PWM5
PWM port 5
IO0_6
Digital I/O port 0_6
INT
Interrupt output pin
ADC 6
ADC port 6
IO0_5
Digital I/O port 0_5
SPI SCK
SPI Bus clock signal
ADC 5
ADC port
IO0_4
Digital I/O port 0_4
WAKEUP
BLE wake up pin, Low/ wake up, High / BLE module
automatically sleep
20
21
ADC4
ADC port 4
IO0_3
Digital I/O port 0_3
UART TX
UART Serial data bus output
SPI MOSI
SPI Master Out , Slave input
ADC3
ADC port 3
IO0_2
Digital I/O port 0_2
UART RX
UART Serial data bus input
SPI MISO
SPI Master input , Slave output
ADC2
ADC port 2
22
IO0_1 / ADC1 Digital I/O port 0_1
/ ADC PORT 1
23
IO0_0 / ADC0 Digital I/O port 0_0
/ ADC PORT 0
24
Reset
BLE hardware reset pin (Low: reset)
Pin Function Description (The module following collectively "BLE"):
a. UART: serial bus, the default baud rate 9600bps, a single packet transmission
is less than 17 bytes, package transmission intervals greater than 20ms.
b. SPI: SPI bus interface, support for less than 2M / S data transmission rate,
a single packet transmission is less than 17 bytes, package
transmission intervals greater than 20ms.
c. IIC: IIC bus interface, support more than 22K / S, less than 400K / S data
transmission rate, a single packet transmission is less than 8 bytes,
package transmission intervals greater than 20ms.
d. MOSI: Master output, Slave input.
e. MISO: Master input, Slave output.
f. SCK: SPI bus clock signal.
g. SDA: IIC data.
h. SCL: IIC clock.
i. WAKEUP: BLE wake up pin, Low _wake up, High/ BLE module automatically sleep.
j. SEL0 & SEL1: MCU and BLE communication mode selection pin. Specific details,
see "(4-3) communication protocol mode selection, I/O setting table ".
k. RESET: BLE hardware reset pin, Low level reset.
l. VCC: BLE module power supply pin voltage range DC 2.0~3.6V.
m. GND: BLE module ground pin.
（2-3）.Communication protocol mode selection, I/O setting Table
Channel Select
Communication
Remark
No.
PIN status
interface state
SEL1
SEL0
UART
SPI
IIC
OK
0K
1.Command mode
Please contact the
Vendor.
OK
OK
2.Description:
0 is Low,1 is high
OK
UART mode：SEL1=0,SEL0=0 or SEL1=0, SEL0=1 or SEL0,SEL1 floating.
SPI mode： SEL1=1,SEL0=0
IIC mode： SEL1=1,SEL0=1
Table（2-4）: Input and output ports Description
Input / output Register pin No.
I/O Port
IO_0
16
17
18
19
20
21
22
23
IO_1
10
14
15
IO_2
NC
NC
NC
NC
NC
IO_3
NC
NC
NC
NC
NC
NC
11
register
Note：BITx=0，Low level out ; BITx=1 High level out
Direction Register pin No.
Direction
DIR0
16
17
18
19
20
21
22
23
DIR1
10
14
15
DIR2
NC
NC
NC
NC
NC
DIR3
NC
NC
NC
NC
NC
NC
11
Register
Note: BITx = 0 is corresponds port input , BITx = 1 is corresponds port output .
PWM port pin No.
PWM5
PWM4
PWM3
PWM2
PWM1
PWM0
16
10
14
15
ADC port pin No.
ADC7
ADC6
ADC5
ADC4
ADC3
ADC2
ADC1
ADC0
16
17
18
19
20
21
22
23
Note: The Blue Numbers of the corresponding port pin No. applications of all
kinds, For example:IO0/bit0 or ADC0 pin is corresponding module pin No.23
Note: This module cannot connect to the external antenna. It has to use the
existing antenna (PCB Antenna).
(3). FCC/Industry Canada Statement (to be placed on End Products)
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
‐Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1) This device may not cause harmful interference, and
2) This
device must accept any interference received, including
interference that may cause undesired operation of the device.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not
be co‐located or operating in conjunction with any other antenna or
transmitter.
Industry Canada (IC) Statement
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Canada, avis d’Industry Canada (IC)
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée
aux deux
conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage;
(2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Notice to OEM integrator
The end user manual shall include all required regulatory information/warning
as show in this manual.
The OEM integrator is responsible for testing their end‐product for any
additional compliance requirements required with this module installed.
If the FCC ID is not visible when the module is installed inside another device,
then the outside of the device into which the module is installed must also
display a label referring to the enclosed module. The end product shall haves
the words “Contains Transmitter Module FCC ID: CCT‐DPV70-01, IC:
4390A-DPV70”.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : 05368
Create Date                     : 2017:06:28 14:13:52+08:00
Modify Date                     : 2017:06:28 14:13:52+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.3.3 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - UserManual06.16?(revised?on?June?26).doc
Creator                         : 05368
Document ID                     : uuid:7b0087b0-65c8-4f9f-9995-7ebbce6513b9
Instance ID                     : uuid:2942ec7d-da39-4f0d-91f1-4938a9e00a2b
Page Count                      : 9

EXIF Metadata provided by EXIF.tools