Flir BelgiumBA RAY260 Fixed Mount VHF marine radio User Manual

Raymarine UK Ltd. Fixed Mount VHF marine radio

User manual

Download: Flir BelgiumBA RAY260 Fixed Mount VHF marine radio User Manual
Mirror Download [FCC.gov]Flir BelgiumBA RAY260 Fixed Mount VHF marine radio User Manual
Document ID1953712
Application IDmBY+nK7IQBx4EEVl7pZx7Q==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize431.38kB (5392215 bits)
Date Submitted2013-04-30 00:00:00
Date Available2013-04-29 00:00:00
Creation Date2013-04-29 16:18:09
Producing SoftwarePDFlib+PDI 7.0.4 (Win32)
Document Lastmod2013-04-30 10:32:27
Document TitleUser manual
Document CreatorArbortext 5.4

Ray260
Installation and operation
instructions
English
Date: 04-2013
Document number: 81343-1-EN
© 2013 Raymarine UK Limited
Trademark and patents notice
Autohelm, hsb2, RayTech Navigator, Sail Pilot, SeaTalk, SeaTalkNG, SeaTalkHS and Sportpilot are registered trademarks of
Raymarine UK Limited. RayTalk, Seahawk, Smartpilot, Pathfinder and Raymarine are registered trademarks of Raymarine
Holdings Limited.
FLIR is a registered trademark of FLIR Systems, Inc. and/or its subsidiaries.
All other trademarks, trade names, or company names referenced herein are used for identification only and are the property
of their respective owners.
This product is protected by patents, design patents, patents pending, or design patents pending.
Fair Use Statement
You may print no more than three copies of this manual for your own use. You may not make any further copies or distribute or use
the manual in any other way including without limitation exploiting the manual commercially or giving or selling copies to third parties.
Software updates
Check the website www.raymarine.com for the latest software releases for your product.
Product handbooks
The latest versions of all English and translated handbooks are available to download in PDF format from the website www.raymarine.com.
Please check the website to ensure you have the latest handbooks.
Copyright ©2013 Raymarine UK Ltd. All rights reserved.
ENGLISH
Document number: 81343-1
Date: 04-2013
Contents
Chapter 1 Important information........................ 7
Chapter 7 Digital selective calling (DSC)........... 41
Making a distress call................................................. 7
Making a Mayday call ................................................ 7
7.1 Digital Selective Calling (DSC) .............................. 42
7.2 Distress calls ....................................................... 43
Safety notices............................................................ 7
General Information ................................................... 8
7.3 Urgency calls ....................................................... 45
7.4 Safety calls .......................................................... 46
Chapter 2 Handbook and product
information........................................................... 11
2.1 Handbook information .......................................... 12
7.5 Routine calls ........................................................ 46
7.6 Group calls .......................................................... 47
7.7 Position requests ................................................. 48
2.2 Product information .............................................. 12
7.8 Position tracking .................................................. 48
7.9 Test calls ............................................................. 49
Chapter 3 Planning the installation ................... 13
7.10 Voice mail .......................................................... 49
3.1 System integration ............................................... 14
7.11 Received call logs .............................................. 50
7.12 Phonebook ........................................................ 50
3.2 Typical systems ................................................... 15
3.3 Installation checklist ............................................. 16
3.4 Schematic diagram .............................................. 16
3.5 System protocols ................................................. 17
3.6 Parts supplied...................................................... 17
7.13 Group list........................................................... 51
7.14 DSC options ...................................................... 51
Chapter 8 VHF operations .................................. 53
8.1 Scan mode .......................................................... 54
Chapter 4 Cables and connections.................... 19
4.1 General cabling guidance ..................................... 20
8.2 Watch modes....................................................... 54
8.3 Priority channels .................................................. 55
4.2 Connections overview .......................................... 20
8.4 Favorite channels................................................. 55
4.3 Power connection ................................................ 21
8.5 Sensitivity ............................................................ 56
4.4 NMEA 0183 connection ........................................ 22
4.5 Loud hailer connection ......................................... 22
8.6 Private channels .................................................. 56
4.6 Handset connection ............................................. 23
4.7 Passive speaker connection ................................. 23
4.8 Active speaker connection .................................... 24
8.7 Automatic Transmitter Identification System
(ATIS) and Marcom-C mode ....................................... 57
8.8 AIS...................................................................... 58
8.9 Voice recorder ..................................................... 58
4.9 SeaTalkng connection ........................................... 24
8.10 System configuration .......................................... 59
Chapter 5 Location and mounting ..................... 25
Chapter 9 Hailer, Fog horn, and Intercom........... 61
5.1 General location requirements .............................. 26
9.1 Hailer .................................................................. 62
5.2 Base station dimensions....................................... 26
9.2 Fog horn.............................................................. 62
9.3 Handset intercom................................................. 63
5.3 Base station mounting .......................................... 27
5.4 Speaker mounting ................................................ 28
5.5 Handset mounting ................................................ 28
Chapter 10 Maintenance ..................................... 65
10.1 Maintenance ...................................................... 66
Chapter 6 Getting started ................................... 31
10.2 Routine checks .................................................. 66
6.1 Controls............................................................... 32
10.3 Cleaning ............................................................ 67
6.2 Switching the radio on .......................................... 32
6.3 Switching the radio off .......................................... 33
10.4 Unit cleaning instructions .................................... 67
6.4 Voltage detection ................................................. 33
6.5 Handset display LCD overview.............................. 34
6.6 Entering your MMSI number ................................. 35
6.7 Entering your ATIS ID........................................... 36
6.8 Selecting NMEA 0183 or SeaTalkng
connection ................................................................ 37
Chapter 11 Troubleshooting ............................... 69
11.1 Troubleshooting.................................................. 70
11.2 VHF Radio troubleshooting ................................. 71
Chapter 12 Technical support ............................ 73
12.1 Raymarine customer support .............................. 74
6.9 Regional programming ......................................... 37
Chapter 13 Technical specification.................... 75
6.10 Adjusting the LCD backlight level ........................ 38
13.1 Technical specification ........................................ 76
6.11 Adjusting the LCD contrast.................................. 38
Chapter 14 Spares and accessories .................. 77
6.12 Changing the transmit power .............................. 39
6.13 GPS setup ......................................................... 39
14.1 Ray260 Spares & Accessories ............................ 78
14.2 SeaTalkng cables and accessories ....................... 78
6.14 Handset station priority ....................................... 40
Appendix A NMEA 0183 sentences ................... 81
Appendix B NMEA 2000 sentences ................... 82
Appendix C VHF Channels ................................. 83
Appendix D Phonetic alphabet........................... 90
Appendix E Prowords ......................................... 91
Ray260
Chapter 1: Important information
Warning: Product installation and
operation
Making a distress call
In an emergency you can use your product to make an automatic
DSC distress call.
55 60 5
10
50
15
45
20
40
35 30 25
RX HI
RX HI
DIS TRESS
UNDESI GNATED
...3
COUNTI NG DOWN
DIS TRESS
UNDESI GNATED
TRANSMITTING ...
OK
OK
RX HI
RX HI
DIS TRESS
UNDESI GNATED
...2
COUNTI NG DOWN
DIS TRESS
AWAITI NG ACK...
REMAINING TI ME
TO RESEND..04'20
OK
RX HI
RX HI
DIS TRESS
UNDESI GNATED
...1
COUNTI NG DOWN
DIS TRESS
00'01
ACKNOWLEDGED
FROM:0012345 6 7
ORI G:mYSHIP
OK
PAUSE
This product must be installed and operated in
accordance with the instructions provided. Failure
to do so could result in personal injury, damage to
your vessel and/or poor product performance.
Warning: Potential ignition source
INTCM
PAUSE
CANCEL
OK
Safety notices
This product is NOT approved for use in
hazardous/flammable atmospheres. Do NOT install
in a hazardous/flammable atmosphere (such as in
an engine room or near fuel tanks).
P 1/3
D12810-1
1. Open the spring loaded door on the rear of the handset.
2. Press and hold the DISTRESS button for 3 seconds.
Once the DISTRESS button is pressed a 3 second count
down will begin, when the count down reaches zero the
distress call is transmitted.
3. Wait for an acknowledgement of your distress call.
The distress call is repeated automatically until it is
acknowledged.
4. Press and hold the PTT button.
5. Slowly and clearly speak the details of the distress:
MAYDAY, MAYDAY, MAYDAY
This is 
MAYDAY 
My position is 
Warning: Positive ground systems
Do not connect this unit to a system which has
positive grounding.
Warning: Switch off power supply
Ensure the vessel’s power supply is switched OFF
before starting to install this product. Do NOT
connect or disconnect equipment with the power
switched on, unless instructed in this document.
Warning: Chassis grounding
Do NOT ground this product using the chassis
ground terminal.
Grounding this product to a vessel’s RF ground
may cause galvanic corrosion.
I am 
Warning: Antenna isolation
I have 
To prevent galvanic corrosion your antenna must
be isolated from any vessel metalwork using a
suitable insulated e.g. plastic, mounting bracket.
I REQUIRE IMMEDIATE ASSISTANCE
OVER
6. Release the PTT button.
Making a Mayday call
In an emergency you can use your product to make a Mayday
call.
1. Press the 16/9 or 16 PLUS button.
2. Press and hold the PTT button.
3. Slowly and clearly speak the details of the distress:
MAYDAY, MAYDAY, MAYDAY
This is 
MAYDAY 
My position is 
I am 
I have 
I REQUIRE IMMEDIATE ASSISTANCE
OVER
4. Release the PTT button.
5. If an acknowledgement is not received then repeat steps
2 to 4 above.
Warning: FCC Warning (Part 15.21)
Changes or modifications to this equipment not
expressly approved in writing by Raymarine
Incorporated could violate compliance with FCC
rules and void the user’s authority to operate the
equipment.
Warning: Maximum Permissible
Exposure
Failure to observe these guidelines may expose
those within the maximum permissible exposure
(MPE) radius to RF radiation absorption that
exceeds the FCC MPE limit. It is the radio
operator’s responsibility to ensure that no one
comes within this radius.
For optimal radio performance and minimal human
exposure to radio frequency electromagnetic
energy, make sure the antenna is:
• connected to the radio before transmitting
• located where it will be away from people
• located at least 1.5 meters (5 feet) from the
radio’s main unit
Caution: Power supply protection
When installing this product ensure the power
source is adequately protected by means of a
suitably-rated fuse or automatic circuit breaker.
Important information
Caution: Perform regular radio
checks
Perform regular radio checks when using your
vessel, as recommended in radio training and
certification schemes and radio equipment rules
of use.
Caution: Ensure proper radio use
Under no circumstances should a DSC distress
alert be sent from your radio for test purposes.
Such action is a violation of rules of use for radio
equipment, and can result in heavy fines.
Caution: Cleaning
When cleaning this product:
• Do NOT wipe the display screen with a dry cloth,
as this could scratch the screen coating.
• Do NOT use abrasive, or acid or ammonia based
products.
• Do NOT use a jet wash.
General Information
Water ingress
Water ingress disclaimer
Although the waterproof rating capacity of this product meets
the standards shown in the table below, water intrusion and
subsequent equipment failure may occur, if the product is
subjected to commercial high-pressure washing. Raymarine will
not warrant products subjected to high-pressure washing.
Base Station
IPX6
Handset
IPX7
Active / passive speaker
IPX7
Disclaimer
Raymarine does not warrant that this product is error-free or that
it is compatible with products manufactured by any person or
entity other than Raymarine.
Raymarine is not responsible for damages or injuries caused by
your use or inability to use the product, by the interaction of the
product with products manufactured by others, or by errors in
information utilized by the product supplied by third parties.
FCC
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
4. Consult the dealer or an experienced radio / TV technician
for help.
Industry Canada
This device complies with Industry Canada License-exempt
RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause interference; and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
This Class B digital apparatus complies with Canadian
ICES-003.
Licensing
Prior to using this product please check your national
requirements for both operators and equipment licensing.
Station Licence
FCC station license requirement
An FCC Ship Radio Station License and Call Sign are not
required for most recreational vessels travelling in US waters.
However, you must obtain a license if your vessel travels to
foreign ports.
Ships that use MF/HF single side-band radio, satellite
communications, or telegraphy must be licensed by the FCC.
You can obtain a Station License by filing FCC Form 605, which
is available from the FCC website listed above.
Industry Canada
Industry Canada license requirement
You do not need a license to operate this product within
sovereign waters of Canada or the US. You will need a license
to operate this radio outside of Canada or the US. To obtain
Industry Canada licensing information, contact the nearest field
or regional office, or write:
Industry Canada Radio Regulatory Branch
Attention: DOSP
300 Slater Street
Ottawa, Ontario
Canada, KIA OC8
Compliance Statement (Part 15.19)
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
FCC Interference Statement (Part 15.105 (b))
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
European licensing requirements
Regulations in some areas require that an Operator’s license is
obtained before operating a VHF radio. It is your responsibility
to determine whether a license is required in your area before
operating this equipment.
Additional information
The following additional information is required for completing a
license application in Canada and the US.
Industry Canada
certification number
4069B-RAY260 D
FCC ID
PJ5–RAY260
FCC Type accepted
Parts 2, 15 and 80
Output power
1 watt (low) and 25 watt (high)
Modulation
FM
Frequency range
155.000 MHz to 165.000 MHz
Ray260
Maritime Mobile Service Identity (MMSI)
This product is a class “D” Digital Selective Calling (DSC) device.
A 9 digit MMSI number is required to operate DSC equipment.
In some areas, a radio operator license is required before an
MMSI number can be issued.
Note: You can request an MMSI number from the same
agency that issues radio or ship radio licenses in your area.
Once obtained, you can program the MMSI number into your
product by following the instruction supplied with the product.
Once obtained, you can program the MMSI number into your
product using the instructions provided in this handbook.
If regulations in your area do not permit you to program the
MMSI number yourself, your Raymarine dealer can program
the number for you.
Obtaining an MMSI number in the United States
You can request an MMSI number from the FCC when you
apply for a Station License. If your vessel does not require
a license, you may obtain an MMSI by contacting BoatUS
www.boatus.com.
Obtaining an MMSI number in Canada
You can obtain an MMSI number from your nearest Industry
Canada Office.
Obtaining an MMSI number in Europe and rest of world
Am MMSI number should be requested from the same agency
that issues radio operator licenses in your area.
Automatic Transmitter Identification System
(ATIS)
Your product includes ATIS functionality for use on the inland
waterways of contracting governments of the “Regional
Arrangement Concerning the Radiotelephone Service on Inland
Waterways” — also known as the “Basel Agreement” .
ATIS adds data at the end of radio transmissions that identifies
your station. ATIS operation can be turned on or off as needed
via the radio’s menu.
An ATIS number can be obtained from the same agency that
issues radio operator licenses in your area.
Your ATIS ID number is derived from your vessel’s call sign.
If your call sign is suitable, your authorized Raymarine dealer
can assist you in decoding your ATIS ID number, which you can
then program into your product using the instructions provided
in this handbook.
Note: The Basel Agreement includes: Germany, Austria,
Belgium, Bulgaria, Croatia, France, Hungary, Luxembourg,
Moldova, the Netherlands, Poland, Romania, Russian
Federation, the Slovak Republic, Switzerland, the Czech
Republic, Ukraine and the Federal Republic of Yugoslavia.
Note: When ATIS is enabled, certain programming steps
have been implemented to protect the integrity of the Basel
agreement, including the blocking of DSC functions when
ATIS is active.
– More than 2 m (7 ft) from the path of a radar beam. A
radar beam can normally be assumed to spread 20 degrees
above and below the radiating element.
• The product is supplied from a separate battery from that used
for engine start. This is important to prevent erratic behavior
and data loss which can occur if the engine start does not
have a separate battery.
• Raymarine specified cables are used.
• Cables are not cut or extended, unless doing so is detailed in
the installation manual.
Note: Where constraints on the installation prevent
any of the above recommendations, always ensure the
maximum possible separation between different items of
electrical equipment, to provide the best conditions for EMC
performance throughout the installation
Antenna mounting and EME exposure
Ensure that the antenna is connected to the radio before
transmission.
Raymarine declares a Maximum Permissible Exposure (MPE)
radius of 1.5 metres (4.9 ft) (per OET Bulletin 65) for this system,
assuming 25 watts output to an omnidirectional antenna of 3dBi
gain or less.
For watercraft with suitable structures, the antenna base must
be at least 3.5 metres (11.5 ft) above the main deck to meet
the MPE for persons up to 2 metres (6.6 ft) tall. For watercraft
without such structures, the antenna must be mounted so that
its base is a minimum of 1.5 metres (4.9 ft) vertically from heads
of all persons.
The antenna must be isolated from the vessel’s metalwork using
an insulated (e.g. plastic) mounting bracket.
Connections to other equipment
Requirement for ferrites on non-Raymarine cables
If your Raymarine equipment is to be connected to other
equipment using a cable not supplied by Raymarine, a
suppression ferrite MUST always be attached to the cable near
the Raymarine unit.
Declaration of conformity
Raymarine UK Ltd. declares that this product is compliant with
the essential requirements of R&TTE directive 1999/5/EC.
The original Declaration of Conformity certificate may be viewed
on the relevant product page at www.raymarine.com.
Product disposal
Dispose of this product in accordance with the WEEE Directive.
The Waste Electrical and Electronic Equipment (WEEE)
Directive requires the recycling of waste electrical and electronic
equipment. Whilst the WEEE Directive does not apply to some
Raymarine products, we support its policy and ask you to be
aware of how to dispose of this product.
EMC installation guidelines
Raymarine equipment and accessories conform to the
appropriate Electromagnetic Compatibility (EMC) regulations,
to minimize electromagnetic interference between equipment
and minimize the effect such interference could have on the
performance of your system
Correct installation is required to ensure that EMC performance
is not compromised.
For optimum EMC performance we recommend that wherever
possible:
Warranty registration
• Raymarine equipment and cables connected to it are:
IMO and SOLAS
– At least 1 m (3 ft) from any equipment transmitting or
cables carrying radio signals e.g. VHF radios, cables and
antennas. In the case of SSB radios, the distance should
be increased to 7 ft (2 m).
Important information
To register your Raymarine product ownership, please visit
www.raymarine.com and register online.
It is important that you register your product to receive full
warranty benefits. Your unit package includes a bar code label
indicating the serial number of the unit. You will need this serial
number when registering your product online. You should retain
the label for future reference.
The equipment described within this document is intended for
use on leisure marine boats and workboats not covered by
International Maritime Organization (IMO) and Safety of Life at
Sea (SOLAS) Carriage Regulations.
Technical accuracy
To the best of our knowledge, the information in this document
was correct at the time it was produced. However, Raymarine
cannot accept liability for any inaccuracies or omissions it
may contain. In addition, our policy of continuous product
improvement may change specifications without notice. As a
result, Raymarine cannot accept liability for any differences
between the product and this document. Please check the
Raymarine website (www.raymarine.com) to ensure you have
the most up-to-date version(s) of the documentation for your
product.
10
Ray260
Chapter 2: Handbook and product information
Chapter contents
•
2.1 Handbook information on page 12
•
2.2 Product information on page 12
Handbook and product information
11
2.1 Handbook information
2.2 Product information
This handbook contains important information regarding your
DSC VHF Radio.
The Ray260 is a Class D Digital Selective Calling (DSC) VHF
radio. DSC enables you to make a selective call to a specific
radio, and to transmit and receive position information to and
from the selected radio. DSC also allows transmission of
a distress alert to all radios within range at the touch of a
button. Once a DSC request is sent and acknowledged voice
communication is carried out on the channel chosen by the
caller. The radio can transmit and receive on all available US,
Canadian and international and private marine VHF channels.
Ray260 handbooks
The following handbooks are applicable to your Ray260:
All documents are available to download in pdf format from the
Raymarine website www.raymarine.com.
Additional handsets, active, and passive speakers can be added
to the standard Ray260 giving up to 3 fully functional stations
that include an intercom function.
Handbooks
Description
Part number
Mounting and getting started
88014
With an optional loud hailer connected the radio can also be
used as a fog horn or loud speaker system.
Installation and operation
instructions
81343
The Ray260 is available in the following variants:
Ray260 mounting template
87167
Speaker mounting template
87168
SeaTalkng handbooks
Description
Part number
SeaTalkng reference manual
Planning and connection of systems based around the
SeaTalkng network.
81300
SeaTalk – SeaTalkng converter handbook
Installation and connection of the SeaTalk - SeaTalkng
converter.
87121
Variant
Description
Part number
Ray260
US/Canadian variant
E70087
Ray260 AIS
US/Canadian variant with
built in AIS receiver
E70088
Ray260E
European variant
E70089
Ray260E AIS
European variant with built in
AIS receiver
E70090
User manuals Print Shop
Raymarine provides a Print Shop service, enabling you to
purchase a high-quality, professionally-printed manual for your
Raymarine product.
Printed manuals are ideal for keeping onboard your vessel, as a
useful source of reference whenever you need assistance with
your Raymarine product.
Visit http://www.raymarine.co.uk/view/?id=5175 to order a
printed manual, delivered directly to your door.
For further information about the Print Shop, please visit the Print
Shop FAQ pages: http://www.raymarine.co.uk/view/?id=5751.
Note:
• Accepted methods of payment for printed manuals are
credit cards and PayPal.
• Printed manuals can be shipped worldwide.
• Further manuals will be added to the Print Shop over the
coming months for both new and legacy products.
• Raymarine user manuals are also available to download
free-of-charge from the Raymarine website, in the popular
PDF format. These PDF files can be viewed on a PC /
laptop, tablet, smartphone, or on the latest generation of
Raymarine multifunction displays.
12
Ray260
Chapter 3: Planning the installation
Chapter contents
•
3.1 System integration on page 14
•
3.2 Typical systems on page 15
•
3.3 Installation checklist on page 16
•
3.4 Schematic diagram on page 16
•
3.5 System protocols on page 17
•
3.6 Parts supplied on page 17
Planning the installation
13
3.1 System integration
Your VHF radio can be connected to the following marine electronics devices.
D12611-1
Item
Device type
Maximum quantity
Suitable devices
Connections
Ray260 handset
3 (1 supplied)
Ray260 handset
1 per base station handset connection
Active Speaker
Ray260 active speaker
1 per handset
Passive speaker
3 (1 supplied)
Ray260 passive speaker
1 per handset
Loud hailer
• 30 Watt Loud hailer
power/data cable
• 30 Watt Loud hailer with listen-back
Raymarine multifunction
display
The Ray260 is compatible with the following
Raymarine multifunction displays:
SeaTalkng or NMEA 0183
• New a Series
• New c Series
• New e Series
• C Series Widescreen (NMEA 0183 DSC
messages only)
• E Series Widescreen (NMEA 0183 DSC
messages only)
• G Series system (NMEA 0183 DSC
messages only)
GPS Receiver
• RS130
• RS125
SeaTalkng or NMEA 0183 with an
NMEA 0183 to NMEA 2000 converter.
• Raymarine multifunction display equipped
with internal GPS
Note: The Ray260 does not support connection to NMEA 0183 and SeaTalkng at the same time.
14
Ray260
3.2 Typical systems
The Ray260 can be installed as a standalone radio with
peripherals or as part of a marine electronics network.
Standalone DSC VHF radio system
D12614-2
1. Ray260 base station
2. Handset
3. Handset extension cable
4. Passive speaker
Planning the installation
15
Extended system
INTCM
SeaTalkng
INTCM
10
INTCM
D1281 1-1
1. Station 1 active speaker
2. Station 1 handset
3. Ray260 base station
4. Loud hailer
5. GPS receiver
6. Station 2 active speaker
7. Station 2 handset
8. Station 3 handset
9. Station 3 passive speaker
10. Multifunction display
Note: Each handset station can include 1 passive and 1 active speaker.
3.3 Installation checklist
3.4 Schematic diagram
Installation includes the following activities:
Installation Task
A schematic diagram is an essential part of planning any
installation. It is also useful for any future additions or
maintenance of the system. The diagram should include:
Plan your system.
• Location of all components.
Obtain all required equipment and tools.
• Connectors, cable types, routes and lengths.
Site all equipment.
Route all cables.
Drill cable and mounting holes.
Make all connections into equipment.
Secure all equipment in place.
Power on and test the system.
16
Ray260
3.5 System protocols
3.6 Parts supplied
Your product can send and receive position information, e.g.
latitude and longitude using any of the following protocols:
The parts supplied with your Ray260 are shown below.
• SeaTalkng
• NMEA 2000
• NMEA 0183
Using these protocols enables your radio to send position
information to other devices in your system whenever it receives:
• a response to a DSC position request.
• a DSC distress call
10
Note: You may find that your product or system does not use
all of the protocols described in this section.
11
12
Seatalkng
SeaTalkng (Next Generation) is an enhanced protocol for
connection of compatible marine instruments and equipment. It
replaces the older SeaTalk and SeaTalk2 protocols.
13
D12624-2
SeaTalkng utilizes a single backbone to which compatible
instruments connect using a spur. Data and power are carried
within the backbone. Devices that have a low draw can be
powered from the network, although high current equipment will
need to have a separate power connection.
SeaTalkng is a proprietary extension to NMEA 2000 and the
proven CAN bus technology. Compatible NMEA 2000 and
SeaTalk / SeaTalk2 devices can also be connected using the
appropriate interfaces or adaptor cables as required.
NMEA 2000
NMEA 2000 offers significant improvements over NMEA 0183,
most notably in speed and connectivity. Up to 50 units can
simultaneously transmit and receive on a single physical bus at
any one time, with each node being physically addressable. The
standard was specifically intended to allow for a whole network
of marine electronics from any manufacturer to communicate on
a common bus via standardized message types and formats.
NMEA 0183
The NMEA 0183 Data Interface Standard was developed by
the National Marine Electronics Association of America. It is an
international standard to enable equipment from many different
manufacturers to be connected together and share information.
The NMEA 0183 standard carries similar information to SeaTalk.
However it has the important difference that one cable will only
carry information in one direction. For this reason NMEA 0183
is generally used to connect a data receiver and a transmitter
together, e.g. a compass sensor transmitting heading to a radar
display. This information is passed in ‘sentences’, each of which
has a three letter sentence identifier. It is therefore important
when checking compatibility between items that the same
sentence identifiers are used some examples of which are:
Ray260 Base station
Ray260 Handset
Ray260 Passive speaker with 1.5 m (4.9 ft.) speaker cable
attached
Speaker gasket
4 x screws for base station mounting
2 x Screws for handset mounting
SeaTalkng blanking plug
2 x handset station blanking plugs
Handset extension kit
10
4 x Thumb nut and studs for speaker mounting
11
Handset mounting clip
12
Documentation pack
13
Power / Data cable 1 m (3.3 ft.)
Handset extension kit contents
The handset extension kit includes the parts shown below.
• VTG - carries Course and Speed Over Ground data.
• GLL - carries latitude and longitude.
D12649-1
• DBT - carries water depth.
• MWV - carries relative wind angle and wind speed data.
NMEA Baud rates
The NMEA 0183 standard operates at a number of different
speeds, depending upon the particular requirement or equipment
capabilities. Typical examples are:
• 4800 baud rate. Used for general purpose communications,
including FastHeading data.
• 38400 baud rate. Used for AIS and other high speed
applications.
Planning the installation
Splash-proof cap
Nut
Extension cable 10 m (32.8 ft.)
Washer
3 x Mounting screws
Gasket
Mounting plate
17
18
Ray260
Chapter 4: Cables and connections
Chapter contents
•
4.1 General cabling guidance on page 20
•
4.2 Connections overview on page 20
•
4.3 Power connection on page 21
•
4.4 NMEA 0183 connection on page 22
•
4.5 Loud hailer connection on page 22
•
4.6 Handset connection on page 23
•
4.7 Passive speaker connection on page 23
•
4.8 Active speaker connection on page 24
•
4.9 SeaTalkng connection on page 24
Cables and connections
19
4.1 General cabling guidance
4.2 Connections overview
Cable types and length
The connections shown below are available on the Ray260
Base station.
It is important to use cables of the appropriate type and length
• Unless otherwise stated use only standard cables of the
correct type, supplied by Raymarine.
• Ensure that any non-Raymarine cables are of the correct
quality and gauge. For example, longer power cable runs may
require larger wire gauges to minimize voltage drop along the
run.
Routing cables
Cables must be routed correctly, to maximize performance and
prolong cable life.
• Do NOT bend cables excessively. Wherever possible, ensure
a minimum bend diameter of 200 mm (8 in) / minimum bend
radius of 100 mm (4 in).
200 mm (8 in)
D12812-1
Antenna connection
HS1 — Station 1 port
HS2 — Station 2 port
• Protect all cables from physical damage and exposure to heat.
Use trunking or conduit where possible. Do NOT run cables
through bilges or doorways, or close to moving or hot objects.
HS3 — Station 3 port
SeaTalkng connection
• Secure cables in place using tie-wraps or lacing twine. Coil
any extra cable and tie it out of the way.
Power / NMEA 0183 / Loud hailer connection
100 mm (4 in)
• Where a cable passes through an exposed bulkhead or
deckhead, use a suitable watertight feed-through.
• Do NOT run cables near to engines or fluorescent lights.
Always route data cables as far away as possible from:
• other equipment and cables,
• high current carrying ac and dc power lines,
• antennae.
Strain relief
Ensure adequate strain relief is provided. Protect connectors
from strain and ensure they will not pull out under extreme sea
conditions.
Circuit isolation
Appropriate circuit isolation is required for installations using
both AC and DC current:
• Always use isolating transformers or a separate power-inverter
to run PC’s, processors, displays and other sensitive electronic
instruments or devices.
• Always use an isolating transformer with Weather FAX audio
cables.
• Always use an isolated power supply when using a 3rd party
audio amplifier.
• Always use an RS232/NMEA converter with optical isolation
on the signal lines.
• Always make sure that PC’s or other sensitive electronic
devices have a dedicated power circuit.
Cable shielding
Ensure that all data cables are properly shielded that the
cable shielding is intact (e.g. hasn’t been scraped off by being
squeezed through a tight area).
Blanking plugs
Connectors not in use should be protected using blanking plugs.
Connectors on the product or accompanying cables, that are
not in use (not connected), should be covered using blanking
plugs if supplied.
20
Ray260
4.3 Power connection
Sharing a breaker
Where more than 1 piece of equipment shares a breaker you
must provide protection for the individual circuits. E.g. by
connecting an in-line fuse for each power circuit.
The power connections required are shown below.
D12612-1
1. Ray260 base station.
D11637-2
2. Power cable.
3. Red positive wire.
4. In-line 10 A fuse.
5. Black negative wire.
Positive (+) bar
Negative (-) bar
Circuit breaker
Fuse
6. In-line 10 A fuse.
Where possible, connect individual items of equipment to
individual circuit breakers. Where this is not possible, use
individual in-line fuses to provide the necessary protection.
7. NMEA 0183 wires.
8. Loud hailer wires
Warning: Chassis grounding
Do NOT ground this product using the chassis
ground terminal.
Grounding this product to a vessel’s RF ground
may cause galvanic corrosion.
Grounding
This product is grounded through the 0 V dc negative wire on
the power cable and does not require a drain (shield) to be
connected to the base station’s ground terminal.
Warning: Positive ground systems
Do not connect this unit to a system which has
positive grounding.
Breakers, fuses and circuit protection
The power cable includes an in-line fuse. It is recommended that
you fit an additional thermal breaker or fuse at the distribution
panel.
In-line fuse rating
Thermal breaker rating
10 A in-line slow-blow fuse fitted
within power cable
7 A (if only 1 device is connected)
Note: The suitable fuse rating for the thermal breaker is
dependent on the number of devices you are connecting. If in
doubt consult an authorized Raymarine dealer.
Cables and connections
21
4.4 NMEA 0183 connection
4.5 Loud hailer connection
The NMEA 0183 wires on the power/data cable can be used to
connect the radio to a GPS receiver or a Raymarine multifunction
display.
A single 30 watt loud hailer can be connected to the base station
via the loud hailer wires on the power / data cable.
Note: Connections cannot be made using SeaTalkng and
NMEA 0183 at the same time.
D12813-1
(+) Hailer wire (Purple)
(-) Hailer wire (Gray)
Connecting loud hailer wires
D12613-1
1. Ray260 base station.
Loud hailer wires should be connected securely and covered to
prevent corrosion.
2. Power/data cable.
3. Yellow – Receive positive (+) wire.
4. Green – Receive negative (-) wire.
5. White – Transmit positive (+) wire.
6. Brown – Transmit negative (-) wire.
The NMEA wires on the product’s power / data cable should
be connected to a compatible NMEA 0183 devices as shown
in the table below:
Ray260
NMEA 0183 device
Yellow – Receive positive (+)
to
Transmit positive (+)
Green – Receive negative (-)
to
Transmit negative (-)
White – Transmit positive (+)
to
Receive positive (+)
Brown – Transmit negative (-)
to
Receive negative (-)
Connecting NMEA 0183 wires
NMEA 0183 wires should be connected securely and covered to
prevent corrosion.
22
Ray260
4.6 Handset connection
4.7 Passive speaker connection
Up to 3 stations can be connected to the base station. A station
must include of a handset and can include a passive and / or
active speaker. A handset must be connected to the station
1 port (HS1), this handset has priority over other connected
handsets.
A passive speaker can be connected to each handset extension
cable using the external speaker wires.
INTCM
D12614-2
1. Ray260 base station.
2. Handset.
3. Handset extension cable.
D12814-1
4. Passive speaker.
Active speaker
Connecting passive speakers
Handset
Base station
Passive speaker
10 m (32.8 ft.) Handset extension cable
Passive speakers must be connected to the system as described
below.
1. Connect the passive speaker connection of the handset
extension cable to the speaker connector on the passive
speaker cable.
10 m (32.8 ft.) Handset extension cable with passive
speaker connector
Optional extension cables can also be used to increase the
distance of the handset from the base station, or to add a
passive speaker.
Note: The maximum extended cable length from base station
to handset is 50 metres (164 ft).
Connecting handsets and cables
Follow the steps below to connect handsets and extension
cables together.
1. Ensure the cable connectors are correctly orientated.
2. Ensure connectors are fully inserted.
3. Tighten locking collars by Rotating clockwise.
Cables and connections
23
4.8 Active speaker connection
4.9 SeaTalkng connection
An optional active speaker can be connected to each of handset.
The Ray260 can interface with Raymarine GPS receivers and
Raymarine multifunction displays using the SeaTalkng connector.
A Raymarine SeaTalkng GPS receiver cannot be connected
directly to the Base station as GPS receivers are powered via
the SeaTalkng backbone.
Note: Connections cannot be made using SeaTalkng and
NMEA 0183 at the same time.
Connecting SeaTalkng
The Ray260 can interface with Raymarine GPS receivers
and Raymarine multifunction displays through the SeaTalkng
connector.
Before connecting to SeaTalkng, refer to the SeaTalkng
Reference Manual, to ensure that the maximum permitted Load
Equivalence Number (LEN), for the SeaTalkng system is not
exceeded once this product is connected.
D12647-1
Base station
Active speaker
Handset
Handset extension cable
Active speakers connect in line with the handset
Connecting active speakers
Active speakers must be connected to the system as described
below.
D12648-1
Connector (1) must be connected either directly to the
handset or to the handset via an extension cable
Connector (2) must be connected either directly to the base
station or to the base station via an extension cable
1. Ensure the cable connectors are correctly orientated.
2. Ensure connectors are fully inserted.
3. Tighten locking collars by Rotating clockwise.
24
D12615-1
1. Rotate the SeaTalkng connector’s locking collar anti
clockwise, to the unlock position.
2. Ensure the spur cable connector is correctly orientated.
3. Fully insert the spur cable connector into the SeaTalkng
connector on the unit.
4. Rotate the locking collar clockwise 2 clicks, to the locked
position.
Ray260
Chapter 5: Location and mounting
Chapter contents
•
5.1 General location requirements on page 26
•
5.2 Base station dimensions on page 26
•
5.3 Base station mounting on page 27
•
5.4 Speaker mounting on page 28
•
5.5 Handset mounting on page 28
Location and mounting
25
5.1 General location requirements
5.2 Base station dimensions
When selecting a location for the unit it is important to consider a
number of factors.
The dimensions of the Ray260 base station are shown below.
Antenna mounting and EME exposure
Compass safe distance
To prevent potential interference with the vessel's magnetic
compasses, ensure an adequate distance is maintained from
the product.
When choosing a suitable location for the product you should
aim to maintain a minimum distance of 1 m (3.28 ft) between
any part of the radio (i.e. transceiver, handset or speaker) and
any compasses.
Ensure that the antenna is connected to the radio before
transmission.
Raymarine declares a Maximum Permissible Exposure (MPE)
radius of 1.5 metres (4.9 ft) (per OET Bulletin 65) for this system,
assuming 25 watts output to an omnidirectional antenna of 3dBi
gain or less.
For watercraft with suitable structures, the antenna base must
be at least 3.5 metres (11.5 ft) above the main deck to meet
the MPE for persons up to 2 metres (6.6 ft) tall. For watercraft
without such structures, the antenna must be mounted so that
its base is a minimum of 1.5 metres (4.9 ft) vertically from heads
of all persons.
The antenna must be isolated from the vessel’s metalwork using
an insulated (e.g. plastic) mounting bracket.
D12606-1
269.5 mm (10.6 in)
168 mm (6.6 in)
66.12 mm (2.6 in)
80.0 mm (3.15 in)
Handset dimensions
Ventilation requirements
The dimensions of the handset are shown below.
To provide adequate airflow:
• Ensure that equipment is mounted in a compartment of
suitable size.
• Ensure that ventilation holes are not obstructed.
• Ensure adequate separation of equipment.
Mounting surface requirements
Ensure units are adequately supported on a secure surface. Do
NOT mount units or cut holes in places which may damage the
structure of the vessel.
Cable routing requirements
Ensure the unit is mounted in a location which allows proper
routing and connection of cables:
INTCM
• Minimum cable bend radius of 100 mm (3.94 in) is required
unless otherwise stated.
• Use cable supports to prevent stress on connectors.
Water ingress
Base station
Although the base station is waterproof to IPX6 standard, it is
recommended that the base station be mounted below decks,
in an area protected from prolonged and direct exposure to rain
and salt spray.
Handset and speakers
The handsets, passive speakers, and active speakers are
waterproof to IPX7 and can be mounted above or below decks.
Although the unit is waterproof, it is good practice to locate it in
an area protected from prolonged and direct exposure to rain
and salt spray.
D12609-2
65.4 mm (2.57 in)
154.4 mm (6.07 in)
7 mm (0.275 in)
38.5 mm (1.5 in)
Electrical interference
Select a location that is far enough away from devices that
may cause interference, such as motors, generators and radio
transmitters/receivers.
Power supply
Select a location that is as close as possible to the vessel’s DC
power supply. This will help to keep cable runs to a minimum.
26
Speaker dimensions
The dimensions of the Ray260 passive / active speaker are
shown below.
Note: The passive speaker does not have a volume control
knob.
Ray260
In order to mount the Ray260 base station follow the steps below.
Note: Raymarine recommends mounting the unit vertically.
5.3 Base station mounting
D12607-1
112 mm (4.4 in)
112 mm (4.4 in)
20.3 mm (0.799 in)
15.55 mm (0.61 in)
25 mm (0.98 in)
30 mm (1.18 in)
91.5 mm (3.6 in)
D12242-1
1. Check the selected location for the unit, a clear flat area
with suitable clearance for air ventilation around the unit is
required.
2. Secure the Base station mounting template in the chosen
location using adhesive tape.
3. Drills 4 holes at the marked location on the template.
4. Remove the mounting template.
5. Screw in the supplied fixing screws approximately half way
into the holes.
6. Place the unit onto the fixing screws.
7. Push the unit down to engage the key slots in the unit.
8. Tighten the screws.
Note: Drill bit, tap size and tightening torque is dependent on
the thickness and type of material the unit is to be mounted on.
Location and mounting
27
5.4 Speaker mounting
5.5 Handset mounting
In order to mount a passive or active speaker follow the steps
below.
In order to mount the handset clip follow the steps below.
0 0
D12608-1
The speaker is designed to be flush mounted.
1. Check the selected location for the unit, a clear flat area is
required.
2. Cut out the identified shaded area(s) from the mounting
template
3. Fix the speaker mounting template (supplied) to the selected
location, using adhesive tape.
4. Drill out the required mounting holes, as indicated on the
mounting template.
5. If possible use an appropriate size hole cutting saw and cut
out the center hole, or
6. Using a suitable hole cutting saw, make pilot holes in each
corner of the cut out area and using a jigsaw cut along the
inside edge of the cut out line.
7. Remove the mounting template.
8. Ensure that the unit fits into the removed area and then file
around the cut edges until smooth.
9. Feed the speaker cable through the cut out hole and
connect the opposite end of the speaker wire to the relevant
connector.
10. Attach the 4 x mounting studs to the rear of the speaker.
11. Hold the speaker into place and secure by tightening the
provided thumb nuts onto the mounting studs.
D12610-1
1. Check the selected location for the handset clip, a clear flat
area is required, with sufficient space around it to place and
remove the handset.
2. Using a pencil, offer up the handset clip to the desired
location and mark the location of the screw holes on the
mounting surface.
3. Drill the mounting holes using a suitable size drill bit.
4. Hold the clip in place and secure using the screws provided.
Note: Drill bit, tap size and tightening torque is dependent on
the thickness and type of material the unit is to be mounted on.
Pass-through panel plate mounting
When installing the handset use the supplied, handset extension
cable kit to pass the cable through a panel (e.g. bulkhead).
D12192-1
Splash-proof cap
Mounting screws x3
Mounting plate
Gasket
Nut
Washer
Extension cable connector
1. Check the selected location for the mounting of the handset
cable extension mounting plate, a clear flat area is required.
2. Using a pencil, offer up the mounting plate to the desired
location and mark the location of the screw holes and the
center hole on the mounting surface.
3. Drill the mounting holes using a suitable size drill bit.
4. Drill the center hole using a 25 mm (1 in.) hole cutting saw.
5. Hold the clip in place and secure using the screws provided.
28
Ray260
6. Pull the connector end of the cable through the hole in the
mounting panel.
Note: The handset extension cable includes a speaker cable.
If you are not connecting an external passive speaker then
cover the speaker cable with waterproof tape or sealant to
prevent corrosion.
7. Insert the washer (labelled 6 in the diagram below) over the
end of the connector.
8. Insert the gasket (labelled 4 in the diagram above) over the
end of the connector.
9. Insert the mounting plate (labelled 3 in the diagram above)
over the end of the connector, ensuring that the screw holes
are aligned with the respective holes in the gasket and the
mounting panel.
10. Place the nut (labelled 5 in the diagram above) over the
connector and tighten clockwise using a 13/16 in. (21 mm)
socket wrench.
11. Align the small end of the splash-proof cap (labelled 1 in the
diagram above) with one of the screw holes on the gasket.
12. Secure the mounting plate to the mounting surface using the
supplied screws.
13. Attach the handset or microphone to the cable connector and
rotate clockwise to secure.
14. Connect the opposite end of the cable to the required
connector either on the base station or to another
pass-through panel plate connector.
Note: Drill bit, tap size and tightening torque is dependent on
the thickness and type of material the unit is to be mounted on.
Location and mounting
29
30
Ray260
Chapter 6: Getting started
Chapter contents
•
6.1 Controls on page 32
•
6.2 Switching the radio on on page 32
•
6.3 Switching the radio off on page 33
•
6.4 Voltage detection on page 33
•
6.5 Handset display LCD overview on page 34
•
6.6 Entering your MMSI number on page 35
•
6.7 Entering your ATIS ID on page 36
•
6.8 Selecting NMEA 0183 or SeaTalkng connection on page 37
•
6.9 Regional programming on page 37
•
6.10 Adjusting the LCD backlight level on page 38
•
6.11 Adjusting the LCD contrast on page 38
•
6.12 Changing the transmit power on page 39
•
6.13 GPS setup on page 39
•
6.14 Handset station priority on page 40
Getting started
31
6.1 Controls
6.2 Switching the radio on
You can access all functions, with the exception of adjusting the
active speaker volume, from the handset.
To power the radio on using any connected handset follow the
steps below.
Ray260 / Ray
260 AIS
With the power off:
1. Press the red 16/9 / 16 PLUS button.
The radio will power up and the radios MMSI number is
displayed on-screen for approximately 3 seconds before
displaying the main screen.
Ray260E / Ra
y260EAIS
INTCM
INTCM
MY MMSI I S
123456789
RAY2 6 0 E
V2 .0 0 A
I NPUT MMSI
TO ACTI VATE DSC
PRESS CLEAR
TO CONTI NUE
RAY2 6 0 E
V2 .0 0 A
D12617-1
D12616-2
1. PTT (Push to talk)
Press and hold to send a voice message. Release to return
to receive mode.
Note: The maximum transmit time is limited to 5 minutes
to prevent un-intentional transmissions from occupying
the VHF channel.
Startup screen with MMSI registered (auto dismisses after 3
seconds).
Startup screen with no MMSI registered (Press CLEAR to
dismiss).
Note: If no MMSI number has been programmed then an
alarm is sounded and a warning message is displayed
INPUT MMSI TO ACTIVATE DSC — PRESS CLEAR TO
CONTINUE. DSC functions will not be available until an MMSI
number has been entered.
2. VOL/SQ
• Adjusts volume up and down.
• Press and release the center button to activate the
squelch threshold adjustment.
• With squelch activated use the up and down buttons to
increase and decrease the squelch level.
3. CLEAR/WX or CLEAR
• Press and release to terminate a function and return to
the last used channel.
• Press and hold for 3 seconds to select the weather mode
(North America and Canada only).
4. 16/9 or 16 PLUS
• Press to power up the radio.
• Press and hold for 5 seconds to power off.
• When powered on press to cycle between priority
channels and last used channel.
5. Soft buttons
The soft button’s functions change according to context,
such as navigate through menus or to make a menu
selection. Press to select the corresponding functions as
identified by the on-screen label.
6. MENU / DSC
• Press and release to access the radio menu.
• Press and hold for 3 seconds to access the DSC menu.
7. OK/INTCM
• Press and release on menu options to confirm a selection
or value.
• Press and hold for 3 seconds to open the intercom menu.
8. Channel Up and Down
• Moves the selected channel up or down.
• Scrolls up or down through menu items.
9. DISTRESS
The Distress button is located on the back of the handset.
Push up the spring loaded cover and press this button to
make a DSC distress call.
32
Ray260
6.3 Switching the radio off
6.4 Voltage detection
To switch the radio off follow the steps below.
The radio detects the power supply voltage and a warning is
displayed if the supply voltage is under or over recommended
power.
With the radio switched on:
1. Press and hold the 16/9 button for 5 seconds.
An over voltage warning is displayed if the radio’s supply voltage
is between 15.7 V dc and 16.0 V dc. The radio will automatically
power down if the supply voltage exceeds 16.5 V dc, the warning
will be cancelled when the radios power supply voltage fails
below 15.6 V dc.
An under voltage alarm is displayed if the radio’s supply voltage
is 10.5 V dc or less. The radio will be unable to operate reliably
below 10.5 V dc.
Getting started
33
6.5 Handset display LCD overview
change request. Applies to Distress and All ships Urgency
calls only.
The information below describes the on-screen characters and
icons which the radio displays on the main screen and what
they mean.
RX TX HI LO ATIS SAVED LOCAL FAV123
I NT
DUP
0016
DL WATCH
0009
M8 2 ° 3 4 .5 N
1 2 3 ° 4 5 .6 W
AM0 1 :2 3 UT
0028A
(Satellite icon) — Indicates that positional data is
available from your GPS.
•
(Envelope icon) — When flashing, indicates that the
radio has received a DSC call. Details of the call can be
viewed in the DSC received calls log.
•
(Cloud icon) — Indicates that the radio is monitoring
for weather alert broadcasts. US and Canada only.
4. Frequency group
Indicates which channel set is selected:
• USA — United States of America.
CHANNEL NAME
0001A
•
• INT — International.
0088A
D12618-1
1. Duplex
• DUP — Indicates the current channel is duplex.
2. Channel suffix
• A — Indicates that the currently selected US or Canadian
channel is simplex, although its International equivalent
is semi-duplex (05A, for example). This channel uses
the transmit frequency of the International channel for
transmitting and receiving. If a channel is simplex in all 3
channel sets (US, Canadian and International — channel
6 for example), the does not require the A suffix.
Note: Simplex means that the radio transmits and
received on the same frequency for this channel.
Semi-duplex channels use separate frequencies to
transmit and receive.
• B — Indicates that you cannot transmit on the currently
selected channel as it is receive only. Used with Canadian
channels only.
3. ICONS
The icon definitions are listed below:
• CAN — Canada.
• WX — Weather
Note: Special licensing is required to receive USA and
Canadian channel sets.
5. Information
• Indicates radio functions, GPS position data or special
conditions, depending on the situation. The screen is
different when transmitting/receiving a DSC call or setting
up a menu item.
6. Channel
Indicates the currently selected channel.
7. Channel name
Indicates the channel name.
8. Soft button legends
Indicates the current function of the associated soft buttons.
DSC Call screen overview
When transmitting or receiving a DSC call, specific call
information is shown on-screen.
• RX (Receiving) — Indicates that the radio is receiving a
radio signal.
RX HI
• TX (Transmitting) — Indicates the PTT button is being
pressed and the radio is transmitting.
• HI (High power) — Indicates that the transmitters power
is set to high (25 watts).
• LO (Low power) — Indicates that the transmitters power
is set to low (1 watt).
• ATIS (ATIS active) — Indicates ATIS transmission is
enabled. Only available in European countries using the
international channel set.
• SAVED (Memory mode) — Indicates the current channel
has been saved in memory. Appears during saved scan
and priority saved scan modes.
• LOCAL (Local/distant mode) — Indicates the radio is in
local reception mode, which decreases receiver sensitivity
in high traffic areas to decrease unwanted reception.
• FAV123 (Favorite channel) — Indicates which of the
3 favorite channel banks is currently selected. Each
bank displays a different favorite channel that you have
assigned for each of the 3 soft button labels at the bottom
of the screen. This gives you a total of 9 favorite channels
that you can switch to at the press of a button.
34
•
(Telephone icon) — Indicates that the radio has
received a voice mail.
•
(Automatic channel changing blocked icon) —
Indicates that your radio will not automatically switch to
the channel requested by an incoming DSC call but will
prompt you to manually accept or decline the channel
DI STRESS
0 0 '0 1
ALERT
FROM:1 2 3 4 5 6 7 8 9
EVENT:UNDESI G
OK
PAUSE
P1 /
D12619-1
1. DSC call information
The DSC call information details.
2. Left soft button function
In this example pressing the left soft button will accept the
incoming distress call.
3. Center soft button function
In this example pressing the center soft button will pause
the current DSC call.
4. Right soft button function
In this example the right soft button is indicating that the
DSC information being shown is page 1 of 4 page of
information, pressing the right soft button will display the
next page of information.
5. Call time
The time the current call has been active.
Ray260
6.6 Entering your MMSI number
Menu screen overview
The radio’s menu options can be viewed on-screen.
To program your radio with your MMSI number follow the steps
below.
HI
- - - MAI N MENU- - - HAI L/ I NTRCOM/ FOG
GPS SETUP
CONNECTI ON
- MY MMSI - - - - - - - ENTER AGAI N
MMSI :- - - - - - - - BACK
OK
HI
HI
OK
HI
HI
- - - - DSC MENU- - - RECEI VED CALLS
MY MMSI
PHONEBOOK
- MY MMSI - - - - - - - ENTER MY MMSI
MMSI :- - - - - - - - -
- MY MMSI - - - - - - - ENTER AGAI N
MMSI :123456789
PRESS [OK]
BACK
BACK
D12620-1
1. Selection arrow
Indicates the currently highlighted menu item.
HI
HI
2. Menu items
This is a list of the available menu items.
- MY MMSI - - - - - - - ENTER MY MMSI
MMSI :1234- - - - -
3. OK
Selecting OK will open the highlighted menu option
BACK
4. Up arrow
Indicates that there are more menu options above , which
can be accessed by pressing the right soft button.
5. Down arrow
Indicates that there are more menu options below, which
can be accessed by pressing the center soft button.
- MY MMSI - - - - - - - CONFI RMED
MMSI :123456789
REGI STER?
NO
HI
YES
HI
- MY MMSI - - - - - - - ENTER MY MMSI
MMSI :123456789
PRESS [OK]
BACK
OK
OK
- MY MMSI - - - - - - - MMSI :123456789
BACK
D12621-1
6. Menu name
Indicates the menu currently displayed.
1. Press and hold the MENU / DSC button to display the DSC
menu.
2. Select MY MMSI from the DSC menu.
• If NO MMSI ID CONTACT DEALER is displayed on-screen
then you must contact your local Raymarine dealer and
request them to input the MMSI number for you.
• If ENTER MY MMSIis displayed then you can manually
enter your MMSI. The first character of the blank MMSI
number will be highlighted.
Note: If ‘0’ is entered as the first digit then the second digit will
automatically be changed to a ‘0’. MMSI numbers beginning
with ‘0’ are only for use by the Coast Guard.
3. Use the Channel Up and Down buttons to cycle through
available numbers.
4. Select Ok to move to the next character.
5. Repeat steps 3 and 4 above until the full 9 digit MMSI number
is displayed on-screen.
6. You can also use the Right arrow and Left arrow soft
buttons to change which character is highlighted.
7. When finished select Ok to confirm the MMSI number.
You will be requested confirm the MMSI number by repeating
the entry.
8. With ENTER AGAIN displayed on-screen follow steps 3 to 6
above to enter the MMSI number again.
9. Select Ok to confirm.
10. If NOT CONFIRMED is displayed then select Back and repeat
steps 2 to 9 above.
11. If CONFIRMED is displayed then select Yes to confirm and
save the MMSI number.
The saved MMSI number is displayed on-screen (e.g.
MMSI:123456789).
12. Select Back to go back to the DSC menu.
Note: You can only enter the MMSI number once, if you have
stored an incorrect MMSI number in your product, the product
will have to be reset by an authorized Raymarine dealer.
Getting started
35
6.7 Entering your ATIS ID
Enabling / Disabling the ATIS function
To program your radio with your ATIS ID follow the steps below.
With the ATIS ID programmed you can now enable or disable
the ATIS function as required by following the steps below.
---MAIN MENU---gGPS SETUP
ATIS OPERATION
CONNECTION
- MY ATI S I D- - - - ENTER AGAI N
I D :- - - - - - - - BACK
OK
HI
HI
HI
-ATIS OPERATIONMY ATIS ID
ATIS FUNCTION
[BACK]
- MY ATI S I D- - - - ENTER AGAI N
I D :123456789
PRESS [OK]
BACK
BACK
HI
- ATI S OPERATI ONMY ATI S I D
ATI S FUNCTI ON
[BACK]
OK
OK
- MY ATI S I D- - - - CONFI RMED
I D :123456789
REGI STER?
NO
BACK
HI
OK
OK
OK
HI
HI
- ATI S FUNCTI ON- ON
OFF
[BACK]
BACK
- ATI S FUNCTI ON- ATI S OFF
THEN DSC ON
PRESS [OK]
OK
BACK
From the ATIS operation menu:
1. Select ATIS Function.
2. Select ON to enable the ATIS function, or
The message ATIS ON THEN DSC OFF is displayed
on-screen to warn that when ATIS is enabled then DSC
functions are not available.
3. Select OFF to disable the ATIS function.
The message ATIS OFF THEN DSC ON is displayed
on-screen to warn that when ATIS is disabled then DSC
functions are available again.
YES
- MY ATI S I D- - - - ID
HI
- ATI S FUNCTI ON- ATI S ON
THEN DSC OFF
PRESS [OK]
D12623-1
HI
-MY ATIS ID----ENTER MY ATIS I D
ID:12 3456 789
PRESS [OK]
- ATI S FUNCTI ON- ON
OFF
[BACK]
OK
HI
HI
-MY ATIS ID----ENTER MY ATIS ID
ID : - --------
BACK
Note: If your radio has been configured to use Marcom-C
mode then ATIS will be permanently enabled and you will not
be able to disable ATIS operation. Marcom-C mode is set by
the dealer at point of sale. If you wish to enable or disable
Marcom-C, please contact your Raymarine dealer.
HI
HI
:123456789
BACK
D12622-2
1. Press and release the MENU / DSC button to display the
main menu.
2. Select ATIS OPERATION from the main menu options.
If no ATIS ID has been programmed then the message PLEASE
INPUT ATIS ID FIRST is displayed.
Note: With the ATIS function enabled the following functions
will be disabled:
• If NO ATIS ID CONTACT DEALER is displayed on-screen
then you must contact your local Raymarine dealer and
request them to input the ATIS ID for you.
• DSC functions.
• If ENTER MY ATIS ID is displayed then you can manually
enter your ATIS ID. All ATIS IDs begin with a 9, this is set
automatically and not shown on the display.
• Multiple watch functions.
• Scan functions.
3. Use the Channel Up and Down buttons to cycle through
available numbers.
4. Select Ok to move to the next character.
5. Repeat steps 3 and 4 above until the full ATIS ID is displayed
on-screen.
6. You can also use the Right arrow and Left arrow soft
buttons to change which character is highlighted.
7. When finished select Ok to confirm the ATIS ID.
You will be requested confirm the ATIS ID by repeating the
entry.
8. With ENTER AGAIN displayed on-screen follow steps 3 to 6
above to enter the ATIS ID again.
9. Select Ok to confirm.
10. If NOT CONFIRMED is displayed then select Back and repeat
steps 2 to 9 above.
11. If CONFIRMED is displayed then select Yes to confirm and
register the ATIS ID.
The saved ATIS ID is displayed on-screen (e.g. ID:
123456789).
12. Select Back to go back to the ATIS Operation menu.
Note: You can only enter the ATIS ID number once, if you
have stored an incorrect ATIS ID number in your product, the
product will have to be reset by an authorized Raymarine
dealer.
36
Ray260
6.8 Selecting NMEA 0183 or SeaTalkng
connection
SeaTalkng
The type of connection in use must be selected (i.e.
or NMEA 0183).
1. Press and release the DSC Menu button.
The main menu is displayed.
2. Select Connection.
3. Select Interface.
4. Select the required connection:
i. Select NMEA 2000 if you are connected to a network or
device using the SeaTalkng connector, or
ii. Select NMEA 0183 if you are connected to a device using
the NMEA 0183 connection.
5. For NMEA 0183 connection on a radio that has a built in AIS
receiver, select the required baud rate, either STD Speed
or High Speed.
6.9 Regional programming
The frequency band of the product can be changed and must be
set to the region the product will be used in.
The regions available are:
• USA
• International
• Canada
Changing the frequency band
Before using the product to make DSC or other calls you must
set the frequency band to the relevant region.
HI
- - - MAI N MENU- - - VHF OPERATIONv
HAIL/INTRCOM/FOG
GPS SETUP
OK
HI
- VHF OPERATI ON- WATCH MODE
FREQUENCY BAND
CHANNEL NAME
OK
HI
- FREQUENCY BANDUSA
INTERNATIONAL
CANADA
OK
D12815-1
From the Main menu:
1. Select VHF OPERATION.
2. Select FREQUENCY BAND.
The list of available regions is displayed:
• USA
• International
• Canada
3. Select the relevant region.
The selected region icon will be displayed on the top left of
the LCD screen.
• USA = USA
• INT = International
• CAN = Canada
Getting started
37
6.10 Adjusting the LCD backlight level 6.11 Adjusting the LCD contrast
The LCD’s backlight level can be adjusted by following the steps
below.
1. Press and release the MENU / DSC button to display the
main menu.
2. Select SYSTEM CONFIG.
3. Select BACKLIGHT.
The backlight level is displayed.
4. Use the Channel Up and Channel Down buttons or the Left
Arrow and Right Arrow soft buttons to adjust the backlight
to the required level.
5. Select Ok to confirm the new backlight level.
38
The LCD’s contrast level can be adjusted by following the steps
below.
1. Press and release the MENU / DSC button to display the
main menu.
2. Select SYSTEM CONFIG.
3. Select CONTRAST.
The contrast level is displayed.
4. Use the Channel Up and Channel Down buttons or the Left
Arrow and Right Arrow soft buttons to adjust the contrast to
the required level.
5. Select Ok to confirm the new contrast level.
Ray260
6.12 Changing the transmit power
6.13 GPS setup
You can change the power level at which the radio transmits at
by following the steps below.
1. Press and release the MENU / DSC button to display the
main menu.
2. Select VHF OPERATION.
3. Select HI/LO POWER.
4. Select the HI/LO soft button to switch between high and low
power.
When connected to a GPS receiver over NMEA 0183 or
SeaTalkng, the radio can display relevant GPS information.
The information that can be displayed is as follows:
• latitude
• longitude
• UTC time
• COG and SOG
When GPS data is available the GPS satellite icon is displayed
on-screen.
If no GPS data is available then the latitude, longitude and time
can be entered manually so that it can be included in DSC
distress transmissions.
Position data received from other vessels can be sent to and
displayed on a connected Raymarine multifunction display.
No GPS position
If no GPS data is available, after 10 minutes of no data the
GPS icon flashes, NO POS DATA and NO GPS is displayed on
screen and an audible warning is sounded.
Once the warning has been acknowledged the GPS icon will
continue to flash and NO GPS will remain on screen. The
warning will be repeated every 4 hours as long as position data
is still unavailable or has not been entered manually.
If position data has been entered manually but has not been
updated during the previous 4 hours the GPS icon flashes, POS
DATA OLD is displayed on screen and an audible warning is
sounded. This warning will be repeated every 4 hours until
position is manually updated or GPS position data becomes
available.
Where no position data is available or has not been manually
updated for 23.5 hours then position data will change to ‘9’s and
time data will change to ‘8’s.
Entering position details manually
If no GPS receiver is present you can manually enter your
position details.
From the main menu:
1. Select GPS SETUP.
2. Select MANUAL POS.
3.
4.
5.
6.
The Manual position screen requires you to input latitude,
longitude and UTC time.
Use the Channel Up and Channel Down buttons to cycle
through the available characters.
Select OK to move to the next character.
Use the Right Arrow and Left Arrow soft buttons to highlight
the next or previous character.
When the relevant information has been entered select
DONE to confirm the details.
Selecting GPS information to display
on-screen
You can select which GPS information is displayed on-screen.
From the GPS setup menu (Main menu > GPS SETUP):
1. Select SETTING.
The list of GPS information is displayed:
• LAT/LON DISPLAY
• TIME DISPLAY
• TIME OFFSET
• TIME FORMAT
• COG/SOG
2. Select the relevant option.
3. Select ON to display this information on-screen and OFF to
hide the information
Getting started
39
Setting time format and offset
You can select the time format and whether an offset is applied
to the time.
From the GPS setup menu (Main menu > GPS SETUP):
1. Select SETTING.
2. Select TIME OFFSET or TIME FORMAT as required.
3. Use the Channel Up and Channel Down buttons to cycle
through the available values.
4. Select OK to confirm.
Selecting stations to display
6.14 Handset station priority
The handset connected to station 1 (HS1) is given priority over
handsets connected to stations 2 (HS2) and 3 (HS3).
Stations 2 and 3 are given the same priority, with the first station
in use given priority. When a station is making a distress call that
station is given priority until the distress call has been completed.
Station 1 can interrupt station 2 and 3 and take priority by
pressing the PTT button.
When station 1 is in use stations 2 and 3 will display STATION
1 IN USE. If station 2 or 3 is in use then station 1 will show the
normal display and the other station will display STATION 2 IN
USE or STATION 3 IN USE.
You can select which contacts from your phonebook you want
incoming position data to be displayed on the multifunction
display.
Station 1
TX LO
INT
From the GPS setup menu (Main menu > GPS SETUP):
1. Select NMEA OUTPUT.
2. Select ALL STATION to display all incoming position data on
your multifunction display, or
3. Select LISTED STATION to select a contact from your
phonebook.
Station 1
in use
FA
0016
STATION1 IN USE
STATION1 IN USE
M8 2 ° 3 4 .5 N
1 2 3 ° 4 5 .6 W
AM0 1 :2 3 UT
CHANNEL NAME
0001A
TX LO
INT
Station 2
in use
0028A
FA
DUP
0088A
V1
TX LO
INT
0016
M8 2 ° 3 4 .5 N
1 2 3 ° 4 5 .6 W
AM0 1 :2 3 UT
0001A
TX LO
INT
Station 3
in use
0028A
FA
DUP
0088A
V1
STATION2 IN USE
0016
M8 2 ° 3 4 .5 N
1 2 3 ° 4 5 .6 W
AM0 1 :2 3 UT
0001A
0028A
0088A
V1
TX LO
0016
STATION3 IN USE
M8 2 ° 3 4 .5 N
1 2 3 ° 4 5 .6 W
AM0 1 :2 3 UT
CHANNEL NAME
0001A
FA
DUP
CHANNEL NAME
CHANNEL NAME
An (!) exclamation mark is placed next to the selected
station.
40
Station 3
V1
DUP
Station 2
0028A
INT
FA
DUP
V1
0016
M8 2 ° 3 4 .5 N
1 2 3 ° 4 5 .6 W
AM0 1 :2 3 UT
CHANNEL NAME
0088A
0001A
0028A
0088A
Ray260
Chapter 7: Digital selective calling (DSC)
Chapter contents
•
7.1 Digital Selective Calling (DSC) on page 42
•
7.2 Distress calls on page 43
•
7.3 Urgency calls on page 45
•
7.4 Safety calls on page 46
•
7.5 Routine calls on page 46
•
7.6 Group calls on page 47
•
7.7 Position requests on page 48
•
7.8 Position tracking on page 48
•
7.9 Test calls on page 49
•
7.10 Voice mail on page 49
•
7.11 Received call logs on page 50
•
7.12 Phonebook on page 50
•
7.13 Group list on page 51
•
7.14 DSC options on page 51
Digital selective calling (DSC)
41
7.1 Digital Selective Calling (DSC)
Routine calls
Traditional VHF radio systems require users to listen until
someone speaks, and then determine whether the call is for
them. DSC ensures that calls are received by alerting or
announcing the intended recipient(s) first so they are ready to
listen to the subsequent message on the relevant channel.
DSC is part of the Global Maritime Distress and Safety System
(GMDSS), a maritime communications system for emergency
and distress messages and all types of routine communications
such as ship-to-ship or ship-to-shore.
DSC is a digital signalling system, which operates on VHF
channel 70. DSC calls include other data such as your vessel’s
identification number, purpose of the call, your position and the
channel you want to speak on.
DSC calls can be divided into 4 categories and are prioritized
as shown below:
Routine calls are used for contacting other vessels, marinas,
or shore stations.
Routine calls are made on channel 70 using the dedicated
Maritime Mobile Service Identity (MMSI) number of the station
to be contacted, selecting a VHF working channel and sending
the call. Both radios automatically switch to the chosen channel
for conversation.
Routine calls can also be made to groups — When groups of
ships need the same information (yacht races, club rallies etc.)
a special group-call identity can be used to enable restricted
broadcast calls.
Note: To transmit precise positions, the radio must be
interfaced to a GPS receiver. Otherwise, regular manual
position updating is required.
1. Distress
2. Urgency
3. Safety
4. Routine
Distress
A Distress call should only be used when there is imminent
danger to a vehicle or person that requires immediate assistance.
When making a distress call the following information is
transmitted to all stations within range:
• Vessel MMSI number.
• Vessel position (must be input manually if no GPS position
data is available).
• Local time (must be input manually if no GPS position data
is available).
• Nature of the distress (when designated).
• Transmission frequency.
The call is automatically repeated at approximately 4 minute
intervals until it is acknowledged either by a coast radio station
(CRS) or a vessel within radio range. Distress calls must be
followed by a MAYDAY call on priority channel 16.
Urgency
An urgency call should be used when there is danger to a vehicle
or person that does not require immediate assistance.
When making an urgency call the following information is
transmitted to all stations within range:
• Vessel MMSI number.
• Vessel position (must be input manually if no GPS position
data is available).
• Local time (must be input manually if no GPS position data
is available).
• Transmission frequency.
Once an urgency call is sent it must be followed with a PAN PAN
voice message on channel 16 and include the necessary details.
Safety
A safety call should be used when there is an important
navigational warning or meteorological forecast/broadcast.
Safety alerts can also used for communications during search
and rescue operations.
When making a safety call the following information is
transmitted to all stations within range:
• Vessel MMSI number.
• Vessel position (must be input manually if no GPS position
data is available).
• Local time (must be input manually if no GPS position data
is available).
• Transmission frequency.
Once a safety call is sent it must be followed with a SECURITE
voice message on channel 16 and include the necessary details.
42
Ray260
7.2 Distress calls
Making a distress call
Making a designated distress call
In an emergency you can use your product to make an automatic
DSC distress call.
When making a distress call you can specify the nature of the
distress and if you do not have a valid GPS position available
you can specify coordinates.
55 60 5
HI
HI
HI
- - - - DSC MENU- - - I NDI VI DUAL
DI STRESS
ALL SHI P
- DI STRESS EVENTUNDESI GNATED
FI RE
FLOODI NG
- - - - DI STRESS- - - EVENT SETUP
POSI TI ON SETUP
[BACK]
OK
OK
OK
10
50
15
45
20
40
35 30 25
RX HI
RX HI
DIS TRESS
UNDESI GNATED
...3
COUNTI NG DOWN
DIS TRESS
UNDESI GNATED
TRANSMITTING ...
OK
OK
RX HI
RX HI
DIS TRESS
UNDESI GNATED
...2
COUNTI NG DOWN
DIS TRESS
AWAITI NG ACK...
REMAINING TI ME
TO RESEND..04'20
OK
RX HI
RX HI
DIS TRESS
UNDESI GNATED
...1
COUNTI NG DOWN
DIS TRESS
00'01
ACKNOWLEDGED
FROM:0012345 6 7
ORI G:mYSHIP
OK
OK
INTCM
PAUSE
CANCEL
PAUSE
P 1/3
D12810-1
1. Open the spring loaded door on the rear of the handset.
2. Press and hold the DISTRESS button for 3 seconds.
HI
DI STRESS POS
LAT: 12 34. 5678 N
LOT: 123 45. 678 9W
UTC: 12:34
Once the DISTRESS button is pressed a 3 second count
down will begin, when the count down reaches zero the
distress call is transmitted.
3. Wait for an acknowledgement of your distress call.
OK
HI
HI
FI RE
LAT: 12 34.5678N
LOT: 123 45.6789W
UTC: 12:34
OK
BACK
SEND DI STRESS
HOLDI NG DOWN
DI STRESS BUTTON
BACK
D12816-1
1. Press and hold the Menu / DSC button for 2 seconds.
The DSC menu is displayed.
2. Select DISTRESS.
The Distress event list is displayed.
3. Select a distress event from the list.
• UNDESIGNATED
• FIRE
• FLOODING
The distress call is repeated automatically until it is
acknowledged.
4. Press and hold the PTT button.
5. Slowly and clearly speak the details of the distress:
MAYDAY, MAYDAY, MAYDAY
This is 
MAYDAY 
My position is 
I am 
I have 
I REQUIRE IMMEDIATE ASSISTANCE
OVER
6. Release the PTT button.
• COLLISION
Making a Mayday call
• GROUNDING
In an emergency you can use your product to make a Mayday
call.
1. Press the 16/9 or 16 PLUS button.
2. Press and hold the PTT button.
3. Slowly and clearly speak the details of the distress:
MAYDAY, MAYDAY, MAYDAY
This is 
MAYDAY 
My position is 
I am 
I have 
I REQUIRE IMMEDIATE ASSISTANCE
OVER
4. Release the PTT button.
5. If an acknowledgement is not received then repeat steps
2 to 4 above.
• LISTING
• SINKING
• ADRIFT
• ABANDONING
• PIRACY
• MANOVERBOARD
4. Select the relevant distress event.
• If your radio is receiving a valid GPS position then the
distress type and coordinates are displayed on-screen,
otherwise you will be prompted to enter your position
coordinates.
5. If prompted enter your position coordinates and local time
using the Left Arrow and Right Arrow soft buttons to move
the cursor and the Numeric keypad to enter the relevant
digits.
6. Select DONE.
7. Select OK to confirm distress details.
8. Follow the steps for making a distress call to transmit the
distress alert.
Cancelling a distress call before transmission
To cancel a distress call before it is transmitted follow the steps
below:
1. Release the DISTRESS button before the count down timer
completes.
When the button is released you will be returned to normal
operation.
Cancelling a distress call after transmission
To cancel a distress call after it has been transmitted follow the
steps below:
Digital selective calling (DSC)
43
1. Press the Cancel soft key.
A warning is displayed to inform the user that they are about
to send a ‘Distress cancel call’.
2. Press the Send soft key.
The ‘Distress cancel call’ is sent.
3. Press the OK soft key.
4. Make a broadcast to all stations giving your vessel’s name,
call sign and MMSI number and cancel the false distress alert
Example: “All, Stations, All Stations, All Stations. This is
, , , . Cancel
my distress alert of , 

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Compression Level               : 6
Compression Type                : auto
Config File                     : C:\program files\ptc\arbortext pe\lib\standard.pdfcf
Create Date                     : 2013:04:29 16:18:09+01:00
Creator                         : Arbortext 5.4
EPS Processor                   : PStill version 1.74.14
Graphics Resolution             : 600
Graphics Resolution Threshold   : 900
JPEG Quality                    : 80
Modify Date                     : 2013:04:30 10:32:27+01:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Compression 0020level           : 6
Compression 0020type            : auto
Config 0020 File                : C:\program files\ptc\arbortext pe\lib\standard.pdfcf
EPS0020processor                : PStill version 1.74.14
Graphics 0020resolution         : 600
Graphics 0020resolution 0020threshold: 900
JPEG0020quality                 : 80
Creator Tool                    : Arbortext 5.4
Metadata Date                   : 2013:04:30 10:32:27+01:00
Producer                        : PDFlib+PDI 7.0.4 (Win32)
Format                          : application/pdf
Document ID                     : uuid:4fa729c3-a320-4875-a5a2-8a875b646158
Instance ID                     : uuid:c4d5dc6a-d2d4-42db-a0a5-73c437130290
Page Layout                     : SinglePage
Page Count                      : 94
EXIF Metadata provided by EXIF.tools
FCC ID Filing: PJ5-RAY260

Navigation menu