Flir BelgiumBA RAY60 Fixed Mount VHF marine radio User Manual
Raymarine UK Ltd. Fixed Mount VHF marine radio
User Manual
Ray50 / Ray60 / Ray70 EN Mounting a nd Ge tting S ta rte d ENGLIS H Da te : 02-2015 Docume nt numbe r: 88033-2-EN © 2015 Ra yma rine UK Limite d ENGLISH Document number: 88033-2 Date: 02-2015 Making a distress call In an emergency you can use your unit to make an automatic DSC distress call. With the spring loaded cover open: 3. Release the PTT button. Warning: Product installation and operation Making a Mayday call This product must be installed and operated in accordance with the instructions provided. Failure to do so could result in personal injury, damage to your vessel and/or poor product performance. In an emergency you can use your unit to make a Mayday call. 1. Press the 16 PLUS button. 2. Press and hold the PTT button. 3. Slowly and clearly speak the details of the distress: 55 60 5 10 50 15 45 20 40 35 30 25 MAYDAY, MAYDAY, MAYDAY This isMAYDAY My position is D13202-1 1. Press and hold the DISTRESS button for 3 seconds. Once the DISTRESS button is pressed a 3 second count down will begin, when the count down reaches zero the DSC distress call is transmitted. The distress call is repeated automatically until it is acknowledged. 2. Press and hold the PTT button, then slowly and clearly speak the details of the distress in the following format: MAYDAY, MAYDAY, MAYDAY I am I have I REQUIRE IMMEDIATE ASSISTANCE My position is I am I have I REQUIRE IMMEDIATE ASSISTANCE This product is NOT approved for use in hazardous/flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere (such as in an engine room or near fuel tanks). Warning: 12 Volt dc only This product must only be connected to a 12 volt dc power source. OVER 4. Release the PTT button. 5. If an acknowledgement is not received then repeat steps 2 to 4 above. Important information This is MAYDAY Warning: Potential ignition source Warning: Read the expanded handbook This document is a subset of the full documentation for your product. For the complete documentation and safety information, please refer to the expanded handbook, available on the Raymarine website (www.raymarine.com). Warning: Positive ground systems Do not connect this unit to a system which has positive grounding. Warning: Switch off power supply Ensure the vessel’s power supply is switched OFF before starting to install this product. Do NOT connect or disconnect equipment with the power switched on, unless instructed in this document. OVER Warning: Chassis grounding Do NOT ground this product using the chassis ground terminal. Grounding this product to a vessel’s RF ground may cause galvanic corrosion. Warning: Antenna isolation To prevent galvanic corrosion your antenna must be isolated from any vessel metalwork using a suitable insulated e.g. plastic, mounting bracket. Warning: Protect unused cables Unused cables and wires should be protected from water ingress and from making contact with metal that may be grounded. • If supplied, use protective boots to ensure that cables that are not connected are protected. • NEVER leave bare ended wires uncovered/unprotected as this could cause a short circuit and can induce galvanic corrosion. Warning: FCC Warning (Part 15.21) Changes or modifications to this equipment not expressly approved in writing by Raymarine Incorporated could violate compliance with FCC rules and void the user’s authority to operate the equipment. Warning: Maximum Permissible Exposure Caution: Ensure proper radio use Failure to observe these guidelines may expose those within the maximum permissible exposure (MPE) radius to RF radiation absorption that exceeds the FCC MPE limit. It is the radio operator’s responsibility to ensure that no one comes within this radius. Under no circumstances should a DSC distress alert be sent from your radio for test purposes. Such action is a violation of rules of use for radio equipment, and can result in heavy fines. For optimal radio performance and minimal human exposure to radio frequency electromagnetic energy, make sure the antenna is: • connected to the radio before transmitting • located where it will be away from people • located at least 1.5 meters (5 feet) from the radio’s main unit Caution: Power supply protection When installing this product ensure the power source is adequately protected by means of a suitably-rated fuse or automatic circuit breaker. Caution: Perform regular radio checks Perform regular radio checks when using your vessel, as recommended in radio training and certification schemes and radio equipment rules of use. Caution: Product cleaning When cleaning products: • If your product includes a display screen, do NOT wipe the screen with a dry cloth, as this could scratch the screen coating. • Do NOT use abrasive, or acid or ammonia based products. • Do NOT use a jet wash. Water ingress Water ingress disclaimer Although the waterproof rating capacity of this product meets the stated IPX standard (refer to the product’s Technical Specification), water intrusion and subsequent equipment failure may occur if the product is subjected to commercial high-pressure washing. Raymarine will not warrant products subjected to high-pressure washing. Disclaimer Raymarine does not warrant that this product is error-free or that it is compatible with products manufactured by any person or entity other than Raymarine. Raymarine is not responsible for damages or injuries caused by your use or inability to use the product, by the interaction of the product with products manufactured by others, or by errors in information utilized by the product supplied by third parties. Ray50 / Ray60 / Ray70 FCC Industry Canada Compliance Statement (Part 15.19) This device complies with Industry Canada License-exempt RSS standard(s). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement (Part 15.105 (b)) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Operation is subject to the following two conditions: 1. This device may not cause interference; and 2. This device must accept any interference, including interference that may cause undesired operation of the device. 300 Slater Street Ottawa, Ontario Industrie Canada (Français) Cet appareil est conforme aux normes d'exemption de licence RSS d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes: 1. cet appareil ne doit pas causer d'interférence, et 2. cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Canada, KIA OC8 European licensing requirements Regulations in some areas require that an Operator’s license is obtained before operating a VHF radio. It is your responsibility to determine whether a license is required in your area before operating this equipment. Additional information – Ray50 The following additional information is required for completing a license application in Canada and the US. Industry Canada certification number 4069B-RAY50D FCC ID PJ5–RAY50 FCC Type accepted Parts 2, 15 and 80 Output power 1 watt (low) and 25 watt (high) Modulation FM Frequency range 155.500 MHz to 163.275 MHz Licensing Prior to using this product please check your national requirements for both operators and equipment licensing. 2. Increase the separation between the equipment and receiver. Station Licence 4. Consult the dealer or an experienced radio / TV technician for help. Industry Canada Radio Regulatory Branch Attention: DOSP This Class B digital apparatus complies with Canadian ICES-003. 1. Reorient or relocate the receiving antenna. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Industry Canada Industry Canada license requirement You do not need a license to operate this product within sovereign waters of Canada or the US. You will need a license to operate this radio outside of Canada or the US. To obtain Industry Canada licensing information, contact the nearest field or regional office, or write: FCC station license requirement An FCC Ship Radio Station License and Call Sign are not required for most recreational vessels travelling in US waters. However, you must obtain a license if your vessel travels to foreign ports. Ships that use MF/HF single side-band radio, satellite communications, or telegraphy must be licensed by the FCC. You can obtain a Station License by filing FCC Form 605, which is available from the FCC website listed above. Additional information – Ray60 The following additional information is required for completing a license application in Canada and the US. Industry Canada certification number 4069B-RAY60D FCC ID PJ5–RAY60 FCC Type accepted Parts 2, 15 and 80 Output power 1 watt (low) and 25 watt (high) Modulation FM Frequency range 155.500 MHz to 163.275 MHz Additional information – Ray70 The following additional information is required for completing a license application in Canada and the US. Industry Canada certification number 4069B-RAY70D FCC ID PJ5–RAY70 FCC Type accepted Parts 2, 15 and 80 Output power 1 watt (low) and 25 watt (high) Modulation FM Frequency range 155.500 MHz to 163.275 MHz Obtaining an MMSI number in the United States EMC installation guidelines You can request an MMSI number from the FCC when you apply for a Station License. If your vessel does not require a license, you may obtain an MMSI by contacting BoatUS www.boatus.com. Obtaining an MMSI number in Canada Raymarine equipment and accessories conform to the appropriate Electromagnetic Compatibility (EMC) regulations, to minimize electromagnetic interference between equipment and minimize the effect such interference could have on the performance of your system You can obtain an MMSI number from your nearest Industry Canada Office. Correct installation is required to ensure that EMC performance is not compromised. Obtaining an MMSI number in Europe and rest of world Am MMSI number should be requested from the same agency that issues radio operator licenses in your area. Automatic Transmitter Identification System (ATIS) Your product includes ATIS functionality for use on the inland waterways of contracting governments of the “Regional Arrangement on the Radiocommunication Service for Inland Waterways” — also known as “RAINWAT”. Maritime Mobile Service Identity (MMSI) ATIS adds data at the end of radio transmissions that identifies your station. ATIS operation can be turned on or off as needed via the radio’s menu. This product is a class “D” Digital Selective Calling (DSC) device. An ATIS ID can be obtained from the same agency that issues radio operator licenses in your area. A 9 digit MMSI number is required to operate DSC equipment. In some areas, a radio operator license is required before an MMSI number can be issued. Your ATIS ID should be programed into your product using the instructions provided. Note: You can request an MMSI number from the same agency that issues radio or ship radio licenses in your area. Once obtained, you can program the MMSI number into your product by following the instruction supplied with the product. Note: Contracting RAINWAT countries include: Austria, Belgium, Bulgaria, Croatia, the Czech Republic, France, Germany, Hungary, Luxembourg, Moldova, Montenegro, the Netherlands, Poland, Romania, Serbia, the Slovak Republic and Switzerland. Once obtained, you can program the MMSI number into your product using the instructions provided. If regulations in your area do not permit you to program the MMSI number yourself, your Raymarine dealer can program the number for you. Note: When ATIS is enabled, certain programing steps have been implemented to protect the integrity of the RAINWAT agreement, including the blocking of DSC functions when ATIS is enabled. Note: In areas of extreme EMC interference, some slight interference may be noticed on the product. Where this occurs the product and the source of the interference should be separated by a greater distance. For optimum EMC performance we recommend that wherever possible: • Raymarine equipment and cables connected to it are: – At least 1 m (3 ft) from any equipment transmitting or cables carrying radio signals e.g. VHF radios, cables and antennas. In the case of SSB radios, the distance should be increased to 7 ft (2 m). – More than 2 m (7 ft) from the path of a radar beam. A radar beam can normally be assumed to spread 20 degrees above and below the radiating element. • The product is supplied from a separate battery from that used for engine start. This is important to prevent erratic behavior and data loss which can occur if the engine start does not have a separate battery. • Raymarine specified cables are used. • Cables are not cut or extended, unless doing so is detailed in the installation manual. Note: Where constraints on the installation prevent any of the above recommendations, always ensure the maximum possible separation between different items of electrical equipment, to provide the best conditions for EMC performance throughout the installation Ray50 / Ray60 / Ray70 Antenna mounting and EME exposure Ensure that the antenna is connected to the radio before transmission. Directive does not apply to some Raymarine products, we support its policy and ask you to be aware of how to dispose of this product. Applicable products This document is applicable to the following products: Raymarine declares a Maximum Permissible Exposure (MPE) radius of 1.5 metres (4.9 ft) (per OET Bulletin 65) for this system, assuming 25 watts output to an omnidirectional antenna of 3dBi gain or less. Warranty registration Name Part number To register your Raymarine product ownership, please visit www.raymarine.com and register online. E70243 Ray50 For watercraft with suitable structures, the antenna base must be at least 3.5 metres (11.5 ft) above the main deck to meet the MPE for persons up to 2 metres (6.6 ft) tall. For watercraft without such structures, the antenna must be mounted so that its base is a minimum of 1.5 metres (4.9 ft) vertically from heads of all persons. It is important that you register your product to receive full warranty benefits. Your unit package includes a bar code label indicating the serial number of the unit. You will need this serial number when registering your product online. You should retain the label for future reference. The antenna must be isolated from the vessel’s metalwork using an insulated (e.g. plastic) mounting bracket. IMO and SOLAS Connections to other equipment Requirement for ferrites on non-Raymarine cables If your Raymarine equipment is to be connected to other equipment using a cable not supplied by Raymarine, a suppression ferrite MUST always be attached to the cable near the Raymarine unit. Declaration of conformity Raymarine UK Ltd. declares that this product is compliant with the essential requirements of R&TTE directive 1999/5/EC. The original Declaration of Conformity certificate may be viewed on the relevant product page at www.raymarine.com. Features • SeaTalkng® / NMEA 2000 • NMEA 0183 • Passive speaker connection E70245 Ray60 • SeaTalkng® / NMEA 2000 The equipment described within this document is intended for use on leisure marine boats and workboats NOT covered by International Maritime Organization (IMO) and Safety of Life at Sea (SOLAS) Carriage Regulations. • NMEA 0183 Technical accuracy • Up to 2 stations To the best of our knowledge, the information in this document was correct at the time it was produced. However, Raymarine cannot accept liability for any inaccuracies or omissions it may contain. In addition, our policy of continuous product improvement may change specifications without notice. As a result, Raymarine cannot accept liability for any differences between the product and this document. Please check the Raymarine website (www.raymarine.com) to ensure you have the most up-to-date version(s) of the documentation for your product. • Passive speaker connection E70251 Ray70 Same as Ray60 with additional: • Built-in AIS receiver • Built-in GNSS (GPS and GLONASS) receiver • Loud hailer connection Product disposal Dispose of this product in accordance with the WEEE Directive. Location and mounting The Waste Electrical and Electronic Equipment (WEEE) Directive requires the recycling of waste electrical and electronic equipment. Whilst the WEEE General location requirements When selecting a location for the unit it is important to consider a number of factors. Antenna mounting and EME exposure Ensure that the antenna is connected to the radio before transmission. Raymarine declares a Maximum Permissible Exposure (MPE) radius of 1.5 metres (4.9 ft) (per OET Bulletin 65) for this system, assuming 25 watts output to an omnidirectional antenna of 3dBi gain or less. For watercraft with suitable structures, the antenna base must be at least 3.5 metres (11.5 ft) above the main deck to meet the MPE for persons up to 2 metres (6.6 ft) tall. For watercraft without such structures, the antenna must be mounted so that its base is a minimum of 1.5 metres (4.9 ft) vertically from heads of all persons. The antenna must be isolated from the vessel’s metalwork using an insulated (e.g. plastic) mounting bracket. Compass safe distance To prevent potential interference with the vessel's magnetic compasses, ensure an adequate distance is maintained from the product. When choosing a suitable location for the product you should aim to maintain the maximum possible distance from any compasses. Typically this distance should be at least 1 m (3 ft) in all directions. However for some smaller vessels it may not be possible to locate the product this far away from a compass. In this situation, when choosing the installation location for your product, ensure that the compass is not affected by the product when it is in a powered state. GPS location requirements In addition to general guidelines concerning the location of marine electronics, there are a number of environmental factors to consider when installing equipment with an internal GPS antenna. Mounting location • Above Decks mounting: Provides optimal GPS performance. (For equipment with appropriate waterproof rating.) • Below Decks mounting: GPS performance may be less effective and may require an external GPS antenna mounted above decks. Ventilation requirements To provide adequate airflow: • Ensure that equipment is mounted in a compartment of suitable size. • Ensure that ventilation holes are not obstructed. • Ensure adequate separation of equipment. Mounting surface requirements Ensure units are adequately supported on a secure surface. Do NOT mount units or cut holes in places which may damage the structure of the vessel. Cable routing requirements Ensure the unit is mounted in a location which allows proper routing and connection of cables: D11537-2 This location provides optimal GPS performance (above decks). In this location, GPS performance may be less effective. This location is NOT recommended for GPS antenna. Vessel construction The construction of your vessel can have an impact on GPS performance. For example, the proximity of heavy structure such as a structural bulkhead, or the interior of larger vessels may result in a reduced GPS signal. Before locating equipment with an internal GPS antenna below decks, seek professional assistance and consider use of an external GPS antenna mounted above decks. Prevailing conditions The weather and location of the vessel can affect the GPS performance. Typically calm clear conditions provide for a more accurate GPS fix. Vessels at extreme northerly or southerly latitudes may also receive a weaker GPS signal. GPS antenna mounted below decks will be more susceptible to performance issues related to the prevailing conditions. • Minimum cable bend radius of 100 mm (3.94 in) is required unless otherwise stated. • Use cable supports to prevent stress on connectors. Warning: Protect unused cables Unused cables and wires should be protected from water ingress and from making contact with metal that may be grounded. • If supplied, use protective boots to ensure that cables that are not connected are protected. • NEVER leave bare ended wires uncovered/unprotected as this could cause a short circuit and can induce galvanic corrosion. Electrical interference Select a location that is far enough away from devices that may cause interference, such as motors, generators and radio transmitters/receivers. Ray50 / Ray60 / Ray70 Power supply Select a location that is as close as possible to the vessel’s DC power supply. This will help to keep cable runs to a minimum. Product dimensions Ray60 and Ray70 product dimensions Ray50 product dimensions The Ray60 and Ray70 can be panel or bracket mounted. The Ray50 can be panel mounted or bracket mounted. Ray60 and Ray70 dimensions (panel mount) Ray50 dimensions (panel mount) 168 mm (6.6 in.) 156 mm (6.1 in.) 143 mm (5.6 in.) 134 mm (5.3 in.) 199 mm (7.8 in.) 88.5 mm (3.5 in.) The product can be mounted in the following configurations. 98.5 mm (3.9 in.) Mounting options 21.5 mm (0.85 in.) 176 mm (6.9 in.) 61.6 mm (2.4 in.) 143.6 mm (5.7 in.) 74 mm (2.9 in.) 59 mm (2.3 in.) 39.75 mm (1.6 in.) 25 mm (1 in .) D13168-1 16.6 mm (0.7 in.) D13170-1 Ray50 dimensions (bracket mount) D13203-1 Ray60 and Ray70 dimensions (bracket mount) 173.75 mm (6.8 in.) 2. Overhead mount 3. Bulkhead mount 4. Panel mount 192.5 mm (7.6 in.) 133 mm (5.2 in.) 121 mm (4.8 in.) 1. Table top mount 25 mm (1 in .) D13169-1 226 mm (8.9 in .) 25 mm (1 in .) 204.6 mm (8 in .) D13171-1 Ray50 Panel mounting Fistmic dimensions Removing the mounting hole covers — Ray50 97.6 mm (3.8 in.) Before the Ray50 can be panel mounted the mounting hole covers must be removed. 68.5 mm (2.7 in.) 8 mm (0.3 in.) 36 mm (1.4 in.) D13172-1 D13205-1 The Fistmic’s fitted, coiled lead can be extended comfortably to approximately 1 meter (3.3 ft.) 1. Using a flat blade screw driver, insert the tip of the screw driver in the slot between the back of the cover and the unit. Bracket mounting 2. Carefully lever the cover forward away from the unit. Follow the steps below to mount the product on it’s bracket. 3. Repeat steps 2 and 3 for the remaining mounting hole covers. Before mounting the unit ensure that you have: • Selected a suitable location, ensuring there is nothing behind the mounting surface that may be damaged when drilling. • Identified the cable connections and route that the cables will take. • Attached the front bezel. Drilling out the mounting holes – Ray50 D13204-1 1. Mark the location of the bracket mounting holes on the mounting surface. The mounting holes must be drilled out. Guides for the mounting holes can be found on the corners of the unit, under the mounting hole covers. 2. Drill holes for the mounting fixings using a drill with a suitable sized drill bit. 3. Use the fixings provided to attach the bracket securely to the mounting surface. x4 4. Attach the unit to the bracket and secure in place using the bracket mounting knobs. Note: Drill bit, tap size and tightening torque is dependent on the thickness and type of material the unit is to be mounted on. D13206-1 1. Using a drill and a 4 mm (5/32) drill bit, drill out the 4 mounting holes. 10 Ray50 / Ray60 / Ray70 Holes should be drilled from the front of the unit, taking care not to damage the unit by applying too much force to the drill. Panel mounting the Ray50 5. Ensure that the unit fits into the removed area and then file around the rough edge until smooth. x4 6. Drill 4 holes as indicated on the template to accept the fixings. 7. Remove the backings from the supplied gasket. To panel mount the Ray50 follow the steps below. Before mounting the product, ensure that you have: 8. Place the gasket in position on the back of the unit and press firmly onto the flange. • Selected a suitable location, ensuring there is nothing behind the mounting surface that may be damaged when drilling / cutting. 9. Connect the power, and other cables to the unit. • Identified the cable connections and route that the cables will take. 11. Attach the mounting hole covers. 10. Slide the unit into place and secure using the fixings provided. D13209-1 1. Using a drill and a 4 mm (5/32) drill bit, drill out the 4 mounting holes. • Removed the mounting hole covers. Holes should be drilled from the front of the unit, taking care not to damage the unit by applying too much force to the drill. • Drilled out the mounting holes on the unit. Panel mounting – Ray60 / Ray70 To panel mount the Ray60 / Ray70 follow the steps below. Before mounting the product, ensure that you have: • Selected a suitable location, ensuring there is nothing behind the mounting surface that may be damaged when drilling / cutting. D13208-1 D13207-1 1. Check the selected location for the unit. A clear, flat area with suitable clearance behind the panel is required. 2. Fix the supplied mounting template to the selected location, using masking or self-adhesive tape. 3. Using a suitable hole saw (the size is indicated on the template), make a hole in each corner of the cut-out area. 4. Using a suitable saw, cut along the inside edge of the cut-out line. Note: The supplied gasket provides a seal between the unit and a suitably flat and stiff mounting surface or binnacle. The gasket should always be used. It may also be necessary to use a marine-grade sealant if the mounting surface or binnacle is not entirely flat and stiff or has a rough surface finish. • Identified the cable connections and route that the cables will take. • Drilled out the mounting holes on the unit. • Removed the front bezel. Ray60 / Ray70 Panel mounting Drilling out the mounting holes – Ray60 / Ray70 Before panel mounting the product the mounting holes must be drilled out. Guides for the mounting holes can be found in the corners of the unit, under the front bezel. 11 Note: The supplied gasket provides a seal between the unit and a suitably flat and stiff mounting surface or binnacle. The gasket should always be used. It may also be necessary to use a marine-grade sealant if the mounting surface or binnacle is not entirely flat and stiff or has a rough surface finish. Fistmic / Handset mounting The Fistmic and optional Handset can be mounted by following the steps below. Whilst only the Fistmic is pictured below the steps are identical when mounting the Handset using the mounting clip. Before mounting the unit, ensure that you have: Attaching the front bezel – Ray60 / Ray70 D13210-1 After installation the front bezel can be attached following the steps below. • Selected a suitable location, ensuring there is nothing behind the mounting surface that may be damaged when drilling. The following procedure assumes that the unit has already been mounted in position. • Identified the cable connections and route that the cables will take. 1. Orientate the bottom-right side of the bezel under the bottom-right side of the unit, ensuring that the clips along the bottom edge of the bezel latch into position. 1. Check the selected location for the unit. A clear, flat area with suitable clearance behind the panel is required. 2. Fix the supplied mounting template to the selected location, using masking or self-adhesive tape. 3. Using a suitable hole saw (the size is indicated on the template), make a hole in each corner of the cut-out area. 4. Using a suitable saw, cut along the inside edge of the cut-out line. D13212-1 1. Check the selected location for the mounting clip, a clear flat area is required, with sufficient space around it to place and remove the Fistmic / Handset. 5. Ensure that the unit fits into the removed area and then file around the rough edge until smooth. 6. Drill 4 holes as indicated on the template to accept the fixings. 7. Remove the backings from the supplied gasket. D1321 1-1 8. Place the gasket in position on the back of the unit and press firmly onto the flange. 2. Ensure the bezel is correctly aligned with the unit, as shown. 9. Connect the power, and other cables to the unit. 3. Apply firm but even pressure to the bezel along the: i. Outer edges - work from the sides upwards and then along the top edge, to ensure that it clips securely into position. ii. Inner edges - ensure that the bezel sits flat. 10. Slide the unit into place and secure using the fixings provided. 11. Attach the front bezel. 2. Using a pencil, offer up the mounting clip to the desired location and mark the location of the screw holes on the mounting surface. 3. Drill the mounting holes using a suitable size drill bit. 4. Hold the clip in place and secure using the screws provided. 5. Hook the Fistmic / Handset over the clip and gently push down until it clicks into position. 4. Check that all control buttons are free to operate. 12 Ray50 / Ray60 / Ray70 Note: The Fistmic can only be hooked and unhooked from the mounting clip when held vertical. 2. Passive speaker connection. Distribution panel connection 3. NMEA 0183 wires It is recommended that your product is wired through your vessel’s distribution panel via a thermal breaker or fuse. 4. Loud hailer wires (Ray70 only.) 5. In-line 10 A fuse 6. Red positive wire 7. Black negative wire. 8. Vessel’s 12 V dc power supply Warning: 12 Volt dc only D13213-1 Note: Drill bit, tap size and tightening torque is dependent on the thickness and type of material the unit is to be mounted on. Warning: Chassis grounding Do NOT ground this product using the chassis ground terminal. Power connection Grounding this product to a vessel’s RF ground may cause galvanic corrosion. The power supply should be connected as shown below: Grounding This product is grounded through the 0 V dc negative wire on the power cable and does not require a drain (shield) to be connected to the base station’s ground terminal. D13092-1 1. Vessel power supply positive (+) 2. In-line fuse. (If your products power cable does not have an in-line fuse then an one fuse should be fitted.) 3. Product power cable 4. Vessel power supply negative (-) 5. Vessel distribution panel Battery connection Your product may be wired directly to the battery using an in-line fuse. Warning: Positive ground systems This product must only be connected to a 12 volt dc power source. Do not connect this unit to a system which has positive grounding. D13091-1 1. Vessel power supply positive (+) 12 v dc + 12 v dc - D13214-1 1. Base station Breakers, fuses and circuit protection The information below is provided as guidance to help protect your product. The example illustrations provided are for common vessel power arrangements, if you are unsure how to provide the correct level of protection then please consult a Raymarine authorized dealer for support. 2. Vessel power supply negative (-) 3. In-line fuse (If your products power cable does not have a built in fuse then an in-line fuse should be fitted.) 4. Product power cable 5. Vessel battery 13 In-line fuse and thermal breaker ratings The following in-line fuse and thermal breaker ratings apply to your product: In-line fuse rating Thermal breaker rating 10 A 7 A (if only connecting one device) Circuit breaker Fuse SeaTalkng® connection Where possible, connect individual items of equipment to individual circuit breakers. Where this is not possible, use individual in-line fuses to provide the necessary protection. Connecting the Fistmic – Ray60 / Ray70 Note: • The suitable fuse rating for the thermal breaker is dependent on the number of devices you are connecting. If in doubt consult an authorized Raymarine® dealer. The Fistmic can be connected directly to the connector on the front of the unit. The product can interface with Raymarine® GPS or GNSS receivers and Raymarine® multifunction displays using the SeaTalkng® connection. A Raymarine® SeaTalkng® GPS or GNSS receiver cannot be connected directly to the product, as GPS and GNSS receivers are powered via the SeaTalkng® backbone. Connecting SeaTalkng® Before connecting to SeaTalkng®, refer to the SeaTalkng® Reference Manual, to ensure that the maximum permitted Load Equivalence Number (LEN), for the SeaTalkng® backbone is not exceeded once this product is connected. • Your product’s power cable may have fitted in-line fuse, if not then you can add an in-line fuse to the positive wire of your products power connection. Sharing a breaker Where more than 1 piece of equipment shares a breaker you must provide protection for the individual circuits. E.g. by connecting an in-line fuse for each power circuit. D13217-1 D11637-2 1. Ensure the Fistmic cable connector is correctly orientated. Positive (+) bar 2. Fully insert the connector into the connector on the front of the unit. Negative (-) bar 3. Rotate the locking collar clockwise until it clicks. 14 D13218-1 SeaTalkng® connector’s locking collar 1. Rotate the anti clockwise, to the unlocked position. 2. Ensure the spur cable connector is correctly orientated. Ray50 / Ray60 / Ray70 3. Fully insert the spur cable connector into the SeaTalkng® connector on the unit. 4. Rotate the locking collar clockwise 2 clicks, to the locked position. NMEA 0183 connection The NMEA 0183 wires can be used to connect the unit to a 3rd party GPS/GNSS receiver or multifunction display. Connecting an antenna Controls and interface The radio must be connected to a suitable antenna (not supplied). The antenna connection must be protected so it cannot come into contact with any bare metal (which may be grounded). A protective boot is supplied that can be used to ensure isolation of the antenna connection. The controls and interface available are as follows: Base station D13220-1 1. Built-in speaker 2. Rotary knob / OK push button — Press knob in to access menu / DSC functions and to confirm selections. Turn rotary clockwise or anti-clockwise to move up and down through menu items or to change channel from the Homescreen. D13219-1 1. Yellow – Receive positive (+) wire. 3. LCD 4. VOL/SQ — Turn knob to adjust volume or squelch up and down. Press center button to switch between volume and squelch control. 2. Green – Receive negative (-) wire. 3. White – Transmit positive (+) wire. 4. Brown – Transmit negative (-) wire. The NMEA wires should be connected to a compatible NMEA 0183 device as shown in the table below: NMEA 0183 wires NMEA 0183 device D13235-1 1. Disconnect your antenna cable from the connector. 2. Push the antenna cable through the supplied protective boot. 3. Re-connect the antenna cable to the connector. Yellow – Receive positive (+) to Transmit positive (+) Green – Receive negative (-) to Transmit negative (-) 4. Plug the antenna connector into the product’s antenna connection and secure by tightening the locking collar. 5. Push the protective boot over the connection. White – Transmit positive (+) to Brown – Transmit negative (-) to Receive positive (+) 6. Secure the protective boot using the supplied cable ties. Receive negative (-) If the antenna connector cannot be removed then another suitable means of protection must be used, such as electrical tape. 5. DISTRESS — Push up the spring loaded cover and press this button to make a DSC distress call. 6. 16 / PLUS — When powered on press to switch between priority channels. 7. Power — Press to power the unit on. Press and hold for 3 seconds to power the unit off. Momentary press to access the shortcut list. 8. Back — Move back through menu options. Fistmic D13221-1 15 1. PTT (Push to Talk) — Press and hold to send a voice message. Release to return to receive mode. Note: The maximum transmit time is limited to 5 minutes to prevent un-intentional transmissions from occupying the VHF channel. 2. Speaker The Homescreen is displayed. 3. Status text — Indicates the current radio mode e.g.: ATIS Mode active, Weather Alert, Scan mode etc. Powering the unit off 4. Channel suffix With the unit powered on: 1. Press and hold the Power button for approximately 3 seconds to power the unit off. 3. Microphone location 4. Channel Up and Down — Changes the channel up or down. 5. HI/LO — Press to switch between High (25 W) and low (1 W) transmit power. 6. 16 / PLUS — When powered on press to switch between priority channels. Homescreen overview The information below describes the on-screen characters and symbols which the radio displays on the main screen and what they mean. With the radio connected to a power supply the power button is used to switch the radio on and off. 1. Press the Power button to power-up the radio. The startup is displayed. • b — Indicates that the channel is a receive only channel. Used for Canadian channels only. Note: You cannot transmit on a receive only channel. Powering the unit on • a — Indicates that the current US or Canadian channel is simplex. This channel uses the transmit frequency of the International channel for transmitting and receiving. If a channel is simplex in all 3 frequency bands (e.g. channel 06, the channel does not require the a suffix. INT Scanning...(All + 16) a 50º51’.615 N 001º14’.450 W s 09:48 UTC SHIP-SHIP Press Back to end scan 06 5. Channel — Indicates the current channel number 6. Location / Time or Location / COG/SOG — Depending on selection displays Location coordinates and current time or Location coordinates and current COG and SOG. 7. Channel Name — Indicates the name of the current channel. 8. Channel type — Indicates the type of channel: Ray60 Software V1.00 MMSI: 123456789 D13222-1 1. Status bar — The status bar displays symbols which indicate the current status of the unit. See Status bar symbols for details. 2. Frequency band — Indicates which channel frequency band is in use: • s = Simplex — Simplex channels transmit and receive on the same frequency. • d = Duplex — Duplex channels use separate frequencies to transmit and receive. 9. Optional text — Provides extra user guidance • USA — United States of America • INT — International OK The startup screen will automatically time-out after 5 seconds. 2. Press the OK button, or wait for the startup screen to time-out. 16 • CAN — Canada • WX — Weather Note: Special licensing is required to receive USA and Canadian channel sets. Ray50 / Ray60 / Ray70 Status bar symbols Symbol The status bar is used to display icons that indicate the radio’s status. Symbol Name Description Reception signal Indicates the relative strength of the radio signal being received. Displays between 0 bars (no transmission being received) and 4 bars (strong reception signal). Transmit Indicates the radio is currently transmitting (e.g. the PTT button is being pressed.) Name Description DSC Indicates that a DSC call has been received Power supply voltage too low Indicates the power supply to the radio is below the specified operating voltage Power supply voltage too high Indicates the radio is currently receiving a transmission Indicates the radio transmitters is in low power (1 watt) or high power (25 watt) mode DSC Calls Watch Mode Indicates the power supply to the radio is above the specified operating voltage Indicates that the weather alerts mode is activated. Weather Mode D13223-1 1. Currently selected menu item 2. Scroll bar 3. Menu items The main menu includes the following items: Symbol GPS Fix Low power The main menu is accessed by Pressing the OK button from the Homescreen. Weather Receive Main menu overview Indicates if the radio has a GPS/GNSS fix. Name Sub-options * DSC Calls • Individual call • Distress call • Position request • Group call • All ships call High power • Phonebook • Call logs Local Indicates the radio is in local reception mode, which decreases receiver sensitivity in high traffic areas to decrease unwanted reception • Test call • DSC set-up * Watch Mode • Dual watch • Triple watch • 2nd priority channel 17 Symbol Name Sub-options Name Sub-options Shortcut list * Weather Mode • Weather Homescreen ** Intercom • Intercom Pressing the Power button once while the radio is switched on will open the Shortcuts list. The Shortcuts list can be used to adjust the brightness, contrast and access frequently used functions. * Scan Mode • All channels Set-up ** Hail/Fog/Intercom Symbol • Language • Saved channels • Units • Saved channels + 16 • Power output • Sensitivity • Edit saved channels • Key beep • Hailer • Channel set-up • Fog horn • Weather alerts • Intercom • GPS set-up • DSC set-up ** Hailer/Fog horn • Hailer • Fog horn Shortcuts • Display set-up • All channels + 16 Backlight Contrast Channel 06 Add/edit shortcuts Frequently used functions can be added by selecting Add/edit shortcuts. • AIS Adjusting Brightness and Contrast • Network output The LCD Brightness and Contrast can be adjusted using the Shortcuts list. • ATIS set-up • Maintenance From any screen: 1. Press the Power button. 2. Select Brightness or Contrast. Note: * Menu items not available when radio has ATIS enabled or if the radio has been pre-programed in MARCOM-C mode. 3. Use the Rotary knob to adjust the Brightness or Contrast to the desired level. 4. Press the Power button again to return to the previous screen. ** The menu name and sub-options depend on the peripheral devices connected to the radio. 18 Ray50 / Ray60 / Ray70 Initial startup Accessing the menu Unless your radio has been pre-programmed; the first time you power-up your radio you will be requested to select certain options. With the exception of your MMSI and ATIS ID, you will also be requested to enter these options after a factory reset. The radio’s various options and settings are contained within the menu. After acknowledging the startup screen, unless previously set you will be prompted to make the following selections: 1. Language selection 2. Turn on AIS reception — Ray70 only Enables the built-in AIS receiver. This step is only applicable to radios with a built-in AIS receiver. See Switching on the AIS receiver for more information. D13228-1 Selects which connection to transmit AIS and DSC information to connected equipment on. This step is only applicable if the AIS receiver was turned on in the previous step. See Selecting a network type for available options. 4. Enter MMSI number Required to enable DSC functions. This option is not required after a factory reset, or if the radio has been pre-programed in MARCOM-C mode, or has ATIS enabled. See Entering an MMSI number for more information. If not already selected you will also be prompted to select your network type. 5. Enter ATIS ID Required when the radio will be used in the inland waterways of Europe. This step is only applicable if the radio has been pre-programed in MARCOM-C mode. See Entering an ATIS ID for more information. 6. Frequency band selection Sets the relevant channels for your region. This step is not applicable if the radio has been pre-programed in MARCOM-C mode. See Changing the radio region for more information. The Ray70’s AIS receiver can be switched on or off. From the Main menu: 1. Select Set-up. 2. Select AIS. 3. Select On. Selecting a network type See Selecting a language for available languages. 3. Select network type Switching on the AIS receiver — Ray70 From the Homescreen. 1. Press the Rotary knob’s OK push button. When connecting your radio to other devices it is important to ensure you select the network connection and type that you want data to be transmitted over. From the Main menu: 1. Select Set-up. 2. Select Network output. The following network types are available: • NMEA 2000 (default) — uses the SeaTalkng® connection to transmit data to other devices. Selecting a language The language the radio uses can be changed. From the Main menu: 1. Select Set-up. 2. Select Language. The languages available are: • English (default) — English • Español — Spanish • Français — French • Deutsch — German • Italiano — Italian • 0183 High speed — uses the NMEA 0183 connection with 38400 baud rate • 0183 Std speed — uses the NMEA 0183 connection with 4800 baud rate. 3. Select the network type relevant to the devices connected to your radio. If your radio is not connected to any other devices any option can be selected. Selecting 0183 Std speed will disable the internal AIS receiver on a Ray70. The Network Output setting determines the baud rate of the NMEA 0183 input: Network output setting NMEA 0183 input baud rate NMEA 2000 Standard speed (4800) 3. Select the language that you want the radio to be set to. NMEA 0183 High Speed High speed (38400) The User interface language is changed to the selected language. NMEA 0183 Standard Speed Standard speed (4800) 19 Entering your MMSI number 7. When the final digit is confirmed select DONE. To program your radio with your MMSI number follow the steps below. EX AM PL Enter MMSI number 1 2 3 4 5 6 7 8 9 Done D13224-1 From the Main menu: 1. Select Set-up. 2. Select DSC set-up. 3. Select ATIS. 4. Select On to enable ATIS mode or Off to disable ATIS mode. Example 8. The MMSI is displayed onscreen, check that it is correct, then: i. Select Yes – Save, or ii. if the number entered is not correct select No – Retry. With ATIS mode enabled the radio’s region will be fixed to the INT (international) frequency band and the following functions are disabled: • DSC functions • Watch Mode • Scan Mode • High/low power is restricted on certain channels Once ATIS has been enabled an ATIS ID must be entered. Entering your ATIS ID When ATIS mode is enabled a unique ATIS ID must be entered. 3. Select MMSI. (Not set) will be displayed if no MMSI number has been set. 4. Use the Rotary knob to cycle through the available numbers and press OK to confirm each number and move to the next digit. You should only enter the unique 9 digit MMSI number provided by your licensing authority. MMSI numbers starting with a ‘0’ are only used for groups and coast stations. If you enter a ‘0’ as the first digit the radio will assume you are entering a coast station MMSI and automatically assign a ‘0’ as the second digit; this is to ensure a group MMSI is not entered as the radio’s unique MMSI. 5. Press the Back button at any time to edit digits you have already entered. 6. Press and hold the OK button to display options to Move cursor back and forward through the digits. 20 Caution: MMSI and ATIS ID entry You can only enter the MMSI number and ATIS ID once! If you store an incorrect MMSI number or ATIS ID in your product, it will have to be reset by an authorized Raymarine® dealer. Enabling and disabling ATIS mode D13225-1 From the Main menu. ATIS is a European system used on some inland waterways. ATIS must be enabled and a unique ATIS ID entered in order to use ATIS mode. 1. Select Set-up. From the Main menu. 1. Select Set-up. 2. Select ATIS set-up. 3. Select ATIS ID. 2. Select ATIS set-up. (Not set) will be displayed if no ATIS ID has been set. Ray50 / Ray60 / Ray70 The first digit is set to a ‘9’ and cannot be changed, this is because all ATIS IDs start with a ‘9’. Caution: MMSI and ATIS ID entry As most ATIS IDs consist of a ‘9’ followed by your 9 digit MMSI number; if your radio already has an MMSI number the ATIS ID will be pre-filled in this format. You can only enter the MMSI number and ATIS ID once! If you store an incorrect MMSI number or ATIS ID in your product, it will have to be reset by an authorized Raymarine® dealer. 4. If the ATIS ID has been pre-filled, check it carefully against your issued ATIS ID. 5. To enter your ATIS ID manually, use the Rotary knob to cycle through the available numbers and press OK to confirm each number and move to the next digit. You should only enter the unique 10 digit ATIS ID provided by your licensing authority. 6. Press the Back button at any time to edit digits you have already entered. D13327-1 Changing the radio region Making a distress call Prior to using the radio you must set the Frequency band to the region your radio will be used in. In an emergency you can use your unit to make an automatic DSC distress call. From the Main menu: With the spring loaded cover open: 7. Press and hold the OK button to display options to Move cursor back and forward through the digits. 8. When the final digit is confirmed select DONE. Example 55 60 5 10 50 15 45 20 40 35 30 25 EX AM PL EnterATIS ID 9 1 2 3 4 5 6 7 8 9 Done 9. The ATIS ID is displayed onscreen, check that it is correct, then: i. Select Yes – Save, or ii. if the number entered is not correct select No – Retry. D13202-1 D13326-1 1. Select Set-up. 2. Select Channel set-up. 3. Select Frequency band. 1. Press and hold the DISTRESS button for 3 seconds. Once the DISTRESS button is pressed a 3 second count down will begin, when the count down reaches zero the DSC distress call is transmitted. 4. Select the relevant region from the list. The available options are: • USA • INT = International • CAN = Canada The distress call is repeated automatically until it is acknowledged. 2. Press and hold the PTT button, then slowly and clearly speak the details of the distress in the following format: MAYDAY, MAYDAY, MAYDAY This is MAYDAY 21 My position is I am 1. Release the DISTRESS button before the count down timer completes. When the button is released you will be returned to normal operation. Example: “All, Stations, All Stations, All Stations. This is , , , . Cancel my distress alert of ,
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 26 Page Layout : SinglePage EPS Processor : PStill version 1.74.14 JPEG Quality : 80 Compression Level : 6 Compression Type : auto Graphics Resolution Threshold : 900 Graphics Resolution : 600 Config File : C:\program files\ptc\arbortext pe\lib\standard.pdfcf Creator : Arbortext 5.4 Create Date : 2015:02:04 10:01:37Z Producer : PDFlib+PDI 7.0.4 (Win32)EXIF Metadata provided by EXIF.tools