Fluke 714B Users Manual

: Fluke Fluke-714B-Users-Manual-806775 fluke-714b-users-manual-806775 fluke pdf

Open the PDF directly: View PDF .
Page Count: 4

PN 4407748

December 2013

© 2013 Fluke Corporation. All rights reserved. Specifications are subject to change without notice.

All product names are trademarks of their respective companies.

1

712C/714C

RTD/TC Calibrator

Safety Sheet

Go to www.fluke.com to register your product, download manuals, and find more information.

A Warning identifies conditions and procedures that are dangerous to the user.

Warning

To prevent possible electrical shock, fire, or personal injury:

• Carefully read all instructions.

• Read all safety information before you use the Product.

• Use the Product only as specified, or the protection supplied by the Product can be compromised.

• Do not use the Product around explosive gas, vapor, or in damp or wet environments.

• Never apply more than 30 V between any two terminals, or between any terminal and earth ground.

• Do not use the Product if it is damaged.

• The battery door must be closed and locked before you operate the Product.

• Remove all probes, test leads, and accessories before the battery door is opened.

712C/714C

Safety Sheet

2

• Remove the input signals before you clean the Product.

• Have an approved technician repair the Product.

• Replace the batteries when the low battery indicator shows to prevent incorrect measurements.

For safe operation and maintenance of the Product:

• Repair the Product before use if the batteries leak.

• Remove the batteries if the Product is not used for an extended period of time, or if stored in

temperatures that exceed the specification of the battery manufacturer. If the batteries are not removed,

battery leakage can damage the Product.

General Specifications

Battery Type .......................... 4 AA batteries

Temperature

Operating ...................... -10 °C to 50 °C

Storage

With Batteries ............... Per specification of the battery manufacturer (not to exceed storage specification without batteries)

Without Batteries .......... -20 °C to 60 °C

Altitude

Operating ...................... 2,000 meters

Storage ......................... 12,000 meters

RTD/TC Calibrator

General Specifications

3

Table 1. Symbols

 Earth Ground  Battery

 Conforms to relevant Australian

Standards.  Risk of danger. Important information. See Manual.

 Inspected and licensed by TÜV Product

Services.  Conforms to European Union directives.

CAT II

MEASUREMENT CATEGORY II is

applicable to test and measuring circuits

connected directly to utilization points

(socket outlets and similar points) of the

low voltage MAINS installation.

CAT III

MEASUREMENT CATEGORY III is applicable to test and

measuring circuits connected to the distribution part of the

building’s low-voltage MAINS installation.

CAT IV

MEASUREMENT CATEGORY IV is

applicable to test and measuring circuits

connected at the source of the building’s

low voltage MAINS installation.

 Conforms to relevant North American Safety Standards.



This product complies with the WEEE Directive (2002/96/EC) marking requirements. The affixed label indicates that you

must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the

equipment types in the WEEE Directive Annex I, this product is classed as category 9 "Monitoring and Control

Instrumentation" product. Do not dispose of this product as unsorted municipal waste. Go to Fluke’s website for recycling

information.

4

LIMITED WARRANTY AND LIMITATION OF LIABILITY

This Fluke product will be free from defects in material and workmanship for three years from the date of

purchase. This warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse,

alteration, contamination, or abnormal conditions of operation or handling. Resellers are not authorized to

extend any other warranty on Fluke’s behalf. To obtain service during the warranty period, contact your nearest

Fluke authorized service center to obtain return authorization information, then send the product to that Service

Center with a description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A

PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL,

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR

THEORY. Since some states or countries do not allow the exclusion or limitation of an implied warranty or of

incidental or consequential damages, this limitation of liability may not apply to you.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

U.S.A.

Fluke Europe B.V.

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

11/99