Fluke Lvd2 Volt Light Users Manual
243809-Installationsheet 243809-InstallationSheet 243809-InstallationSheet 095969 Batch4 unilog cesco-content
Fluke-LVD2-Volt-Light-User-Manual-Brochure Fluke-LVD2-Volt-Light-User-Manual-Brochure
2015-09-09
: Fluke Fluke-Lvd2-Volt-Light-Users-Manual-810133 fluke-lvd2-volt-light-users-manual-810133 fluke pdf
Open the PDF directly: View PDF 
.
Page Count: 2
LVD2
VoltAlert
Safety Sheet
Read First: Safety Information
WX Warning
To avoid possible electric shock or personal injury:
If the Tester is used in a manner not specied by the manufacturer, protection ●
provided by the Tester may be affected.
Do not use if the ashlight does not operate, or if battery door clip is not ●
securely fastened.
Test on a known live source within the rated ac voltage range of the product, ●
both before and after use to ensure unit is in good working condition.
When using the Tester, if tip does not glow, voltage could still be present. ●
The Tester indicates active voltage in the presence of electrostatic elds of
sufcient strength generated from the source (MAINS) voltage. If the eld
strength is low, the Tester may not provide indication of live voltages. Lack of
an indication occurs if the Tester is unable to sense the presence of voltage
which may be inuenced by several factors including, but not limited to:
Shielded wire/cables ●
Thickness and type of insulation ●
Distance from the voltage source ●
Fully-isolated users that prevent an effective ground ●
Receptacles in recessed sockets/ differences in socket design ●
Condition of the Tester and Batteries ●
Do not use if the Tester appears damaged or if the Tester is not operating ●
properly. If in doubt, have the Tester serviced.
Use product with arrow visible and keep ngers behind light indicating area. ●
Do not use for dc voltage measurements or around voltages exceeding 600 ●
volts, or in the presence of variable motor drives.
Use caution with voltages above 30 V ac as a shock hazard may exist. ●
Do not allow the Tester to directly touch live circuits. ●
Using the Tester while attached to any metal object could lead to electric ●
shock or personal injury.
Do not stare or look directly at the LED ash light. The light is extremely ●
bright.
Comply with local and national safety requirements. ●
Use proper protective equipment as required by local or national authorities. ●
Table 1. Symbols
TDouble Insulated.
XHazardous Voltage. Risk of electric shock.
WRisk of danger. Important information.
Conforms to relevant Canadian and US Standards.
Conforms to relevant European Union directives.
Conforms to relevant Australian standards.
Do not dispose of this product as unsorted municipal waste. Go to Fluke’s
website for recycling information.
CAT IV Equipment is designed to protect against transients from the primary supply
level. (i.e. - electricity meter or overhead /underground utility service).
sTechnischer Überwachungs Verein. German certifying body.
PN 3496908 July 2009
© 2009 Fluke Corporation. Specications are subject to change without notice.
All rights reserved. Printed in China.
FOR USE BY COMPETENT
PERSONS
Anyone using this instrument should be
knowledgeable and trained about the risks
involved with measuring voltage, especially
in an industrial setting, and the importance of
taking safety precautions and of testing the
instrument before and after using it to ensure
that it is in good working condition.
Contacting Fluke
Technical Support USA: 1-800-44-FLUKE (1-800-443-5853) ●
Calibration/Repair USA: 1-888-99-FLUKE (1-888-993-5853) ●
Canada: 1-800-36-FLUKE (1-800-363-5853) ●
Anywhere in the world: +1-425-446-5500 ●
Or, visit Fluke’s website at www.uke.com.
To register your product, visit http://register.uke.com.
To view, print, or download the latest manual supplement, visit
http://us.uke.com/usen/support/manuals.
LIMITED WARRANTY AND LIMITATION OF LIABILITY
This Fluke product will be free from defects in material and workmanship for two
years from the date of purchase. This warranty does not cover fuses, disposable
batteries, or damage from accident, neglect, misuse, alteration, contamination,
or abnormal conditions of operation or handling. Resellers are not authorized
to extend any other warranty on Fluke’s behalf. To obtain service during the
warranty period, contact your nearest Fluke authorized service center to obtain
return authorization information, then send the product to that Service Center
with a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES,
SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR
IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE
OR THEORY. Since some states or countries do not allow the exclusion or
limitation of an implied warranty or of incidental or consequential damages, this
limitation of liability may not apply to you.
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
11/99
