Follet 205448 Quick Start Guide
2014-07-05
: Follet Follet-205448-Quick-Start-Guide follet-205448-quick-start-guide follet pdf
Open the PDF directly: View PDF .
Page Count: 4
Download | |
Open PDF In Browser | View PDF |
Slope Front Ice Storage Bins Order parts online (US only) www.follettice.com Installation and Parts Manual Following installation, please forward this manual to the appropriate operations person. Follett Corporation 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.com Follett Europe Polska Mokry Dwór 26C • 83-021 Wislina, Poland +48 (58) 785-6140 • Fax +48 (58) 785-6159 www.folletteurope.com 205448R04 Welcome to Follett Follett ® ice storage bins enjoy a well-deserved reputation for excellent performance, long-term reliability and outstanding after-the-sale support. To ensure that this slope front bin delivers the same degree of service, we ask that you take a moment to review this manual before beginning the installation of the bin. Should you have any questions or require technical help at any point, please call our technical service group, +1 (877) 612-5086 (US and Canada only) or +1 (610) 252-7301 (Worldwide) or +48 (58) 785-6140 (Europe and Middle East only). Before you begin After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in the filing of a claim, if necessary. Important cautions Avoid excessive tightening force when connecting to the bin drain fitting. Do not apply excessive heat if any sweating of fittings is necessary. Heat conduction through metal may melt threads in plastic drain fitting. 2 Installation 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Fig. 1 Remove all packing material from bin. Remove all tape and temporary fastenings from door and outside of bin. Remove set of four legs and any other accessories packed inside bin. Lay bin on its back, being careful to protect finish, and remove bolts holding skid to bin. Screw legs into tapped holes in bin bottom and tighten to seat legs well against bottom. Set bin upright and move to permanent location. Remove protective paper from stainless steel surfaces. Adjust “foot” at bottom of each leg to level bin in both directions. Mount icemaker(s) on bin in accordance with icemaker manufacturer’s instructions. Connect drain line to 1" IPS female fitting located in bottom of bin. Make final connections to icemaker. catch assem lift door Lift door catches (Fig. 1) 1. Position lift door in upright position. 2. Center catch on icemaker front above door and position catch to securely hold door when open. 3. Drill two (2) 7/64 (2.78 mm) holes through catch holes and into icemaker face. 4. Install catch using two (2) #6-1/2 sheet metal screws supplied. front of icemaker Fig. 2 icemaker back Icemaker tie-downs (Fig. 2) (Required for some icemaker applications only) Certain icemaker/bin combinations require the installation of a tie-down strap. If straps have been included with your bin, proceed as follows: 1. Locate icemaker back flush with bin back. 2. Using center of vertical slot as a template, drill through icemaker wall with a 15/64" (5.95 mm) drill. 3. Fasten straps to icemaker and bin (bin holes are predrilled) with #14 x 1/2 sheet metal screws and washers provided 15/64" (5.95 mm) hole drilled through icemaker wall tie-down strap Icemaker drain (Required for some icemaker applications only) Some machines require a special drain system. For these machines Follett predrills the hole and provides a 3/4" straight threaded drain fitting to be installed bin back through the hole. To install the fitting: 1. Remove plastic nut on fitting. 2. From inside bin (liner side), insert threaded portion through hole provided in side of bin. 3. Replace plastic nut on threaded portion and tighten against outside of bin. 4. Connect supplied tubing to icemaker drain connection after installing icemaker. Cleaning and sanitizing Interior bin cleaning Follett slope front ice storage bins are equipped with polyethylene liner walls and stainless steel bottoms that should be cleaned and sanitized prior to use and periodically with any cleaning and sanitizing products suitable for use in a food zone. Important: Follett Corporation recommends installing a properly-sized, activated carbon (charcoal) water filter on water supply to icemaker to remove chlorine. Exterior bin cleaning Exterior stainless steel surfaces can be cleaned with a stainless steel cleaner such as 3M* Stainless Steel Cleaner & Polish or equivalent. * 3M is a registered trademark of 3M Company in the US and other countries. 3 Replacement parts pivot hinge foaming plug lift door gasketing pivot pin Front View Front View (inside surface) Foamed Lift Door Front View Hinge Side View Hinge Side View Catch and Door Description Part # Lift door, 29.25" (743 mm) x 15" (381 mm), for 30" (762 mm) wide bins (includes pivot hinges and pins) 501153 Lift door, 43.25" (1099 mm) x 15" (381 mm), for 44" (1118 mm) wide bins (includes pivot hinges and pins) 501154 Lift door, 47.25" (1200 mm) x 15" (381 mm), for 48" (1219 mm) wide bins (includes pivot hinges and pins) 501299 Lift door, 51.25" (1302 mm) x 15" (381 mm), for 52" (1321 mm) wide bins (includes pivot hinges and pins) 501155 Catch, for lift doors when icemaker is flush with bin front 500083 Catch, for lift doors when icemaker is set back from bin front 500984 Hinges, pivot (2), door mount, for all foamed lift doors 501157 Pins, pivot (2), for all lift doors 500343 Gasket, for 30" (762 mm) wide bins with poly backed lift doors 501871 Gasket, for 44" (1118 mm) wide bins with poly backed lift doors 501872 Gasket, for 48" (1219 mm) wide bins with poly backed lift doors 501873 Gasket, for 52" (1321 mm) wide bins with poly backed lift doors 501874 Gasket, plastic edge extrusion, for ice drop hole in top of bin 500785 Drain assembly, plastic 500977 Drain fitting, blow down 501652 Lock nut, drain, blow down 501653 Tubing, drain, blow down 501654 Drain assembly, blow down (includes 501652, 501653, 501654) 501655 Legs (set of 4), 6" (153 mm) adjustable to 7.5" (191 mm), plastic 500089 Legs (set of 4), 6" (153 mm) adjustable to 7.5", (191 mm) stainless 500272 Legs (set of 4), 6" (153 mm) adjustable to 7.5" (191 mm), stainless, with flanged feet 501300 Legs (set of 4), 12" (305 mm) adjustable to 13.5" (343 mm), die cast zinc 500645 Lift doors Door hardware Gaskets Miscellaneous Shovel, plastic 501796 Bracket, shovel 502360 Scoop, ice, San Jamar 00146365 Sealant, RTV, 5 oz tube 500727 Follett is a registered trademark of Follett Corporation, registered in the US. Follett Corporation 801 Church Lane • Easton, PA 18040, USA 4 +1 (610) 252-7301 • Fax +1 (610) 250-0696 www.follettice.com Follett Europe Polska Mokry Dwór 26C • 83-021 Wislina, Poland +48 (58) 785-6140 • Fax +48 (58) 785-6159 www.folletteurope.com 205448R04 02/11