Follet 205448 Quick Start Guide
2014-07-05
: Follet Follet-205448-Quick-Start-Guide follet-205448-quick-start-guide follet pdf
Open the PDF directly: View PDF 
.
Page Count: 4
Installation and Parts Manual
Slope Front
Ice Storage Bins
205448R04
Following installation, please forward this manual
to the appropriate operations person.
Order parts online (US only)
www.follettice.com
Follett Europe Polska
Mokry Dwór 26C • 83-021 Wislina, Poland
+48 (58) 785-6140 • Fax +48 (58) 785-6159
www.folletteurope.com
Follett Corporation
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
2
Welcome to Follett
Follett
® ice storage bins enjoy a well-deserved reputation for excellent performance, long-term reliability and
outstanding after-the-sale support. To ensure that this slope front bin delivers the same degree of service, we ask
that you take a moment to review this manual before beginning the installation of the bin. Should you have any
questions or require technical help at any point, please call our technical service group, +1 (877) 612-5086 (US
and Canada only) or +1 (610) 252-7301 (Worldwide) or +48 (58) 785-6140 (Europe and Middle East only).
Before you begin
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If
damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in the ling of
a claim, if necessary.
Important cautions
Avoid excessive tightening force when connecting to the bin drain tting.
Do not apply excessive heat if any sweating of ttings is necessary. Heat conduction through metal may
melt threads in plastic drain tting.
3
Installation
1. Remove all packing material from bin.
2. Remove all tape and temporary fastenings from door and outside of bin.
3. Remove set of four legs and any other accessories packed inside bin.
4. Lay bin on its back, being careful to protect nish, and remove bolts holding
skid to bin.
5. Screw legs into tapped holes in bin bottom and tighten to seat legs well
against bottom.
6. Set bin upright and move to permanent location.
7. Remove protective paper from stainless steel surfaces.
8. Adjust “foot” at bottom of each leg to level bin in both directions.
9. Mount icemaker(s) on bin in accordance with icemaker manufacturer’s
instructions.
10. Connect drain line to 1" IPS female tting located in bottom of bin.
11. Make nal connections to icemaker.
Lift door catches (Fig. 1)
1. Position lift door in upright position.
2. Center catch on icemaker front above door and position catch to securely
hold door when open.
3. Drill two (2) 7/64 (2.78 mm) holes through catch holes and into icemaker
face.
4. Install catch using two (2) #6-1/2 sheet metal screws supplied.
Icemaker tie-downs (Fig. 2)
(Required for some icemaker applications only)
Certain icemaker/bin combinations require the installation of a tie-down strap.
If straps have been included with your bin, proceed as follows:
1. Locate icemaker back ush with bin back.
2. Using center of vertical slot as a template, drill through icemaker wall with
a 15/64" (5.95 mm) drill.
3. Fasten straps to icemaker and bin (bin holes are predrilled) with
#14 x 1/2 sheet metal screws and washers provided
Icemaker drain
(Required for some icemaker applications only)
Some machines require a special drain system. For these machines Follett
predrills the hole and provides a 3/4" straight threaded drain tting to be installed
through the hole. To install the tting:
1. Remove plastic nut on tting.
2. From inside bin (liner side), insert threaded portion through hole provided in side of bin.
3. Replace plastic nut on threaded portion and tighten against outside of bin.
4. Connect supplied tubing to icemaker drain connection after installing icemaker.
Cleaning and sanitizing
Interior bin cleaning
Follett slope front ice storage bins are equipped with polyethylene liner walls and stainless steel bottoms that
should be cleaned and sanitized prior to use and periodically with any cleaning and sanitizing products suitable
for use in a food zone.
Important: Follett Corporation recommends installing a properly-sized, activated carbon (charcoal) water lter on
water supply to icemaker to remove chlorine.
Exterior bin cleaning
Exterior stainless steel surfaces can be cleaned with a stainless steel cleaner such as 3M* Stainless Steel
Cleaner & Polish or equivalent.
* 3M is a registered trademark of 3M Company in the US and other countries.
catch assem
lift door
front of icemaker
Fig. 1
icemaker back
bin back
15/64"
(5.95 mm)
hole drilled
through
icemaker
wall
tie-down
strap
Fig. 2
4
lift door
Front View (inside surface)
Foamed Lift Door
foaming plug
Front View Front View
Hinge
pivot pin
pivot hinge
Side View
Hinge
gasketing
Side View
Catch and Door
Replacement parts
Description Part #
Lift doors
Lift door, 29.25" (743 mm) x 15" (381 mm), for 30" (762 mm) wide bins
(includes pivot hinges and pins)
501153
Lift door, 43.25" (1099 mm) x 15" (381 mm), for 44" (1118 mm) wide bins
(includes pivot hinges and pins)
501154
Lift door, 47.25" (1200 mm) x 15" (381 mm), for 48" (1219 mm) wide bins
(includes pivot hinges and pins)
501299
Lift door, 51.25" (1302 mm) x 15" (381 mm), for 52" (1321 mm) wide bins
(includes pivot hinges and pins)
501155
Door hardware
Catch, for lift doors when icemaker is ush with bin front 500083
Catch, for lift doors when icemaker is set back from bin front 500984
Hinges, pivot (2), door mount, for all foamed lift doors 501157
Pins, pivot (2), for all lift doors 500343
Gaskets
Gasket, for 30" (762 mm) wide bins with poly backed lift doors 501871
Gasket, for 44" (1118 mm) wide bins with poly backed lift doors 501872
Gasket, for 48" (1219 mm) wide bins with poly backed lift doors 501873
Gasket, for 52" (1321 mm) wide bins with poly backed lift doors 501874
Gasket, plastic edge extrusion, for ice drop hole in top of bin 500785
Miscellaneous
Drain assembly, plastic 500977
Drain tting, blow down 501652
Lock nut, drain, blow down 501653
Tubing, drain, blow down 501654
Drain assembly, blow down (includes 501652, 501653, 501654) 501655
Legs (set of 4), 6" (153 mm) adjustable to 7.5" (191 mm), plastic 500089
Legs (set of 4), 6" (153 mm) adjustable to 7.5", (191 mm) stainless 500272
Legs (set of 4), 6" (153 mm) adjustable to 7.5" (191 mm), stainless, with anged
feet
501300
Legs (set of 4), 12" (305 mm) adjustable to 13.5" (343 mm), die cast zinc 500645
Shovel, plastic 501796
Bracket, shovel 502360
Scoop, ice, San Jamar 00146365
Sealant, RTV, 5 oz tube 500727
205448R04
02/11
Follett Europe Polska
Mokry Dwór 26C • 83-021 Wislina, Poland
+48 (58) 785-6140 • Fax +48 (58) 785-6159
www.folletteurope.com
Follett Corporation
801 Church Lane • Easton, PA 18040, USA
+1 (610) 252-7301 • Fax +1 (610) 250-0696
www.follettice.com
Follett is a registered trademark of Follett Corporation, registered in the US.
