Food Automation Service Techniques XWIRE-GATEWAY Food quality and supply chain monitor equipment User Manual Letter Size

Food Automation - Service Techniques, Inc. Food quality and supply chain monitor equipment Letter Size

User Manual

Download: Food Automation Service Techniques XWIRE-GATEWAY Food quality and supply chain monitor equipment User Manual Letter Size
Mirror Download [FCC.gov]Food Automation Service Techniques XWIRE-GATEWAY Food quality and supply chain monitor equipment User Manual Letter Size
Document ID1581371
Application IDcKaQtVphaif+EHcuSMIRRw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize41.25kB (515643 bits)
Date Submitted2011-11-15 00:00:00
Date Available2012-05-10 00:00:00
Creation Date2008-09-19 09:34:32
Producing SoftwareQuarkXPress(R) 7.3
Document Lastmod2008-09-19 09:34:32
Document TitleLetter Size
Document CreatorQuarkXPress(R) 7.3

Direct, Inc.
Installation Guide
Xwire Universal SmartAdapter for
Communications-Enabled Appliances
TM
Xwire SmartBezel Adapter for Process Controllers
TM
Xwire SmartGateway PC Adapter
TM
SmartAdapter
SmartBezel
SmartGateway
SAVE these instructions
for future reference.
24/7 Toll-Free Technical Support
1-866-840-4271
www.MySCK.com
(from the U.S., Canada and the Caribbean)
Xwire
TM
Direct, Inc.
NOTICES
SCK Direct, Inc. is not liable for any use of product not in accordance with SCK Direct, Inc.’s installation and operation
instructions.
BEFORE USING THIS EQUIPMENT, OR FOR ANY QUESTIONS ON
THE OPERATION OF THE APPLIANCE, CONSULT AND FOLLOW ALL
INSTRUCTIONS AND SAFETY WARNINGS FOUND IN THE APPLIANCE OPERATOR’S MANUAL SUPPLIED FROM THE
MANUFACTURER OF THE APPLIANCE.
CLEANING
Using a clean damp cloth, wipe down the products when necessary using a commercial quality foodservice-approved detergent.
DO NOT IMMERSE.
Changes or modifications not expressly
approved by SCK Direct, Inc. could void the
manufacturer’s warranty and the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and
NEVER use chemical or abrasive cleaners on SCK products.
 Connect the equipment into an outlet on a circuit different
receiver.
TOOLS REQUIRED FOR INSTALLATION
 Consult the dealer for help.
from that to which the receiver is connected.
Flat screwdriver (for SmartBezel)
Pliers (for SmartBezel)
Phillips screwdriver (for SmartAdapter)
Drill bit: 3/16” if using anchor. #50 if installing into metal (for
SmartAdapter)
TABLE OF CONTENTS
Installation: Wireless SmartGateway Adapter . . . . . . . . . . . . . .3
Installation: SmartBezel Adapter
for FAST VC-210 & FAST EM-99 Controllers . . . . . . . . .4
Installation: Universal SmartAdapter
for FAST TRACKER Timers . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installation: Universal SmartAdapter
for Fryers & Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Light Bar and LED Status Charts . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Changing the Default PAN ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
© 2008 SCK Direct, Inc.
229-51316 Rev F
www.MySCK.com
installation guide
STEP 1
The SmartGateway should be installed first.
Xwire Wireless
SmartGateway Adapter
REQUIRED PARTS
(A)
Xwire Wireless SmartGateway Adapter
SCK Part No. 231-60207-01
(B)
USB Cable, 5M
SCK Part No. 141-15734
INSTALLATION
1.
Connect USB cable to the communication port on the SmartGateway.
2.
Power off the PC and connect the SmartGateway to an available USB port
using the USB cable.
NOTE: It’s important to power down for proper configuration.
3.
Verify the LED sequence on the SmartGateway is correct per your application by referring to the charts on page 6.
© 2008 SCK Direct, Inc.
229-51316 Rev F
www.MySCK.com
Xwire
TM
Direct, Inc.
STEP 2
The SmartBezel Adapter
2.
Clamp self-tapping connector to these wires to provide a
24VAC output for the SmartBezel.
3.
Connect the two spade terminals to the pair coming from
the SmartBezel.
4.
Connect the 3-pin Molex connector on the SmartBezel to
the 3-pin Molex on the controller.
5.
Position the SmartBezel onto the
front of the FAST Controller.
Carefully place the five SmartBezel
wires into the channel on the
FAST Controller.
6.
Install the FAST Controller on the
fryer and verify the LED sequence
is correct per your application by
referring to the charts on page 6.
Xwire SmartBezel Adapter for
FAST VC-210 & FAST EM-99
CONTROLLERS
REQUIRED PARTS
(1)
Xwire SmartBezel Adapter
SCK Part No. 231-60206-01
(2)
Self-tapping Connectors (included)
SCK Part No. 141-51026
Qty. 2
INSTALLATION
1.
Locate wires numbered 1 and 3 in the 9-pin connector on
the FAST VC-210 or FAST EM-99 controllers.
The FAST Controller is now ready to be used as an SCK Xwire
wireless device.
© 2008 SCK Direct, Inc.
229-51316 Rev F
www.MySCK.com
installation guide
Xwire Universal SmartAdapter for
STEP 3
The Universal SmartAdapters
FRYERS AND OVENS
Xwire Universal SmartAdapter for
(FAST.)® TRACKER TM TIMERS
REQUIRED PARTS
(A) Xwire Universal SmartAdapter for Fryers and Ovens
SCK Part No. 231-60208-01
(B) Self-tapping Connectors (included)
SCK Part No. 141-51026
Qty. 2
REQUIRED PARTS
(A) Xwire Universal SmartAdapter for FAST TRACKER Timers
SCK Part No. 231-60208-01
(B) Harness for Xwire Universal SmartAdapter
i.
12” SCK Part No. 222-50700-01
ii. 48” SCK Part No. 222-50700-02
(C) Harness: Choose One
i.
SCK Part No. 222-50702-01
ii. SCK Part No. 222-50701-01
iii. SCK Part No. 222-50701-02
(D) Velcro Brand Fastener
(C) Mounting Kit.
SCK Part No. 213-50761-01
If something is missing, please call 1-866-840-4271 (8:00 a.m. 5:00 p.m. EST).
If something is missing, please call 1-866-840-4271 (8:00 a.m. 5:00 p.m. EST).
INSTALLATION
1.
Pull the SCK-enabled Controller away from appliance.
Locate wires numbered 1 and 3 in either the 15-pin connector or the 9-pin connector (depending on the Controller) on
the back of the Controller. These are your 24VAC.
2.
Clamp the self-tapping connector to these wires to provide
a 24VAC output to the SmartAdapter and also the two pigtail wires that are supplied.
3.
Connect the two pigtail wire terminals to the pair coming
from the harness.
4.
Connect the 3- or 4-pin Molex (depending on Controller)
from the harness to the controller.
5.
Drill a hole in the back of the appliance to feed harness
through.
6.
Connect the harness to the SmartAdapter and mount using
Velcro tape that is supplied.
INSTALLATION
1.
2.
Connect harness to the communication port on top of the
TRACKER Timer.
Connect other end of harness to the Xwire Universal
SmartAdapter. Mount the SmartAdapter using the supplied
Velcro.
Note: Mount in a place the SCK Xwire SmartGateway will
receive a signal.
3.
Verify the LED sequence on the SmartAdapter is correct per
your application by referring to the charts on page 6.
The TRACKER Timer is now ready to be used as an SCK Xwire
wireless device.
Note: Mount in a place the SCK Xwire SmartGateway will
receive a signal.
7.
Re-mount the SCK-enabled Controller back into the appliance and verify the LED sequence on the SmartAdapter
indicator is correct by referring to the charts on page 6.
The SCK-enabled Controller is now ready to be used as an
SCK Xwire wireless device.
© 2008 SCK Direct, Inc.
229-51316 Rev F
www.MySCK.com
Xwire
TM
Direct, Inc.
Light Bars and Status LED
The SCK Xwire status indicator consists of three colors (Green, Red and
Orange) to visually indicate transmission strength and operating status to
the operator.
See the charts below for details.
SIGNAL STRENGTH INDICATORS (LIGHT BARS)
How Do I Know if It’s Working?
STRONG
Under normal operating conditions, the status LED will be solid
All light bars are lit RED.
green and all or some of the signal strength LEDs (light bars) will
GOOD
be lit depending on signal strength. In most cases, you’ll see the
At least two light bars are lit RED.
green status LED lit solid while the signal strength light bars
change from time to time.
WEAK
Only one light bar is lit RED.
NONE
No light bars are lit RED.
STATUS LED CHART
LED Color LED Blink Rate
Description
ORANGE
2 sec ON,
2 sec OFF
Device cannot communicate with the SCK device
after already connecting to
the wireless network.
ORANGE
Very Fast
Device is initializing.
GREEN
Solid On
Device has found a
SmartGateway and is now
connected to the network.
GREEN
Very Fast
Device is waiting for a
reply for data sent to
another device.
© 2008 SCK Direct, Inc.
229-51316 Rev F
www.MySCK.com
installation guide
TROUBLESHOOTING / LED CODES
LED Action
Description
Solution
1.
Verify that all enabled controls are set to a
different SCK address.
All LEDs blink in two
short bursts followed
by one second of off
time.
The device is connected to a wireless network but not to an SCK-enabled control.
1.
2.
3.
4.
Make sure device is SCK compatible.
Make sure communication port is connected.
Check SCK wiring.
Install it on a known working appliance.
All LEDs blink on and
off simultaneously
every 500ms.
All LEDs strobe.
Device has detected a multiple SCK address
conflict and is waiting for resolution (currently participating as address 30)
Device is searching for a SmartGateway.
1.
2.
3.
Status LED flashes
green/orange continuously.
The radio on the SmartGateway has been
turned OFF.
1.
Orange LED blinks ON Device is attempting to resolve an SCK
for 2 seconds, then
address conflict by changing to address 30,
OFF for 2 seconds.
but there is already another device on the
SCK network using address 30.
Device cannot communicate with the radio.
Verify the SmartGateway is turned ON.
Install the Xwire device closer to the
SmartGateway.
A SmartRepeater may need to be added to
extend the range. Contact your SCK Sales
Representative.
Contact your local Helpdesk, or SCK
Support at 1-866-840-4271
1.
Verify that all enabled controls are set to a
different SCK address.
1.
2.
Try cycling power to the unit OFF, then ON.
Contact SCK Support.
THE FOLLOWING IS INCLUDED FOR REFERENCE ONLY AND SHOULD BE PERFORMED ONLY BY
AN SCK CERTIFIED TECHNICIAN.
Changing the Default PAN ID
1)
With the device powered ON, press the PAN ID button
and note the LED pattern that is illuminated. This
pattern indicates the default PAN ID.
2)
Press the PAN ID button to change to the next available
PAN ID. The PAN ID button must be pressed within 2seconds of a previous button press or the device will
timeout and return to its previous mode).
3)
The last selection before the timeout occurs will be the
selected PAN ID. If a PAN ID selection differs from the
previous selection, the Xwire device will remove itself
from its current network, reconfigure, and join/start the
network with the new PAN ID.
(Personal Area Network Identification)
The factory default PAN ID is 1. Should your SCK Xwire
device experience interference that prevents it from working
properly, the network PAN ID may be overridden and selected
manually:
Locating the PAN ID Button on
the Xwire Devices
Xwire SmartBezel -- PAN ID button is located in the
rear of the unit in the slot immediately below the
mounting screw location
NOTE: If the PAN ID button is not pressed within 10-seconds, the unit will begin scanning for an available
network and you must wait for the scanning sequence to
complete before the PAN ID button is enabled.
Xwire Universal SmartAdapter -- PAN ID button is
located on the back of the unit in the access way
labeled Channel
Xwire Wireless SmartGateway -- PAN ID button is
located on the right-hand side of the unit in the open
access way
© 2008 SCK Direct, Inc.
4)
229-51316 Rev F
You must set the PAN ID on all Xwire devices to the same
PAN ID to allow the devices to communicate properly.
www.MySCK.com
Troubleshooting
Should you experience problems installing your SCK Xwire products, or any aspect of your SCK Direct, Inc. services, please contact
the SCK HelpDesk toll-free at 1.866.840.4271.
Optional SCK System Components
SCK has a variety of optional accessories to help you complete
your kitchen automation:
SCK Kitchen Advisor Information Server
SCK Remote Input Device
SCK KSM Kitchen Status Monitor
SCK-Enabled Appliance Controllers
SCK Wireless (XwireTM) Appliance Interface
SCK Wireless (XwireTM) Temperature/Door SmartSensorTM
SCK Wireless (XwireTM) SmartGateway
SCK Wired Backbone
For additional information on any of these accessories, or to
request Technical Specification Sheets, please contact your SCK
Representative or contact SCK Customer Support toll-free at
1-866-840-4271 (Monday-Friday, 8:00 a.m. to 5:00 p.m. EST).
WARRANTY
SCK Direct, Inc. warrants all new Xwire hardware for 1 year from the
date of purchase. SCK Direct, Inc. warrants all other items for a period of 90 days unless otherwise stated at the time of purchase.
Thank You for Choosing
SCK Direct, Inc!
This document contains confidential information. The dissemination, publication, copying, or duplication of this document or the
software described herein without prior written authorization is
strictly prohibited.
Specifications subject to change without notice.
(FAST.)® is a registered trademark of Food Automation - Service
Techniques, Inc.
Smart Commercial Kitchen and SCK are registered trademarks of
Technology Licensing Corporation.
SCK Direct, Inc. products are covered under U.S. and foreign
patents, plus patents pending.
Direct, Inc.
SCK Direct, Inc.
905 Honeyspot Road
Stratford, CT 06615 USA
+1 203.377.4174 voice
+1 203.377.8187 fax
1.866.840.4271 toll-free sales & helpdesk
www.MySCK.com; info@mysck.com
229-51316 Rev. F
© 2008 SCK Direct, Inc.
Printed in the USA
19SEP2008

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 8
Create Date                     : 2008:09:19 09:34:32
Creator                         : QuarkXPress(R) 7.3
Producer                        : QuarkXPress(R) 7.3
Modify Date                     : 2008:09:19 09:34:32
X Press Private                 : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%MarksAllSeparations: true.%%EndComments
Title                           : Letter Size
EXIF Metadata provided by EXIF.tools
FCC ID Filing: UJ7-XWIRE-GATEWAY

Navigation menu