Fortinet 120506 2T2R PCIeModule selectable 5GHz+2.4G User Manual WMDQ 177ACN xps

Download:
Mirror Download [FCC.gov]
Document ID	2742396
Application ID	CowwDlpWQUWdZSJ3BsAKfg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	22.51kB (281422 bits)
Date Submitted	2015-09-10 00:00:00
Date Available	2015-09-10 00:00:00
Creation Date	2017-09-15 11:27:32
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-09-15 11:27:32
Document Title	User Manual_WMDQ-177ACN.xps
Document Creator	Adobe Acrobat 11.0.12

WMDQ-177ACN
2T2R PCIeModule
802.11b/g/n/ac/n/a
User Manual
Version 1.0
Gemtek Technology Co., Ltd.
www.gemtek.com.tw
No.15-1 Zhonghua Road, HsinChu
Industrial Park, HuKou Hsiang,
HsinChu Hsien,Taiwan, R.O.C.
Introduction
WMDQ-177ACN is a 5Ghz +2.4G dual Band selectable 2T2R PCIe mini
Card Module based on the Qualcomm QCA9892 solution which features
improved transmission power and sensitivity by Gemtek.
Using the QCA9892 external FEM, it is the ideal cost effective solution for
platform integration.
With enhanced technologies such as advanced power management and
receiver boost, it makes the WMDQ-177ACN the ideal 5Ghz+2.4G 2T2R
module.
Hardware
General Information
Model name
Chipset
Interface
Operating Voltage
Antenna Connectors
PCB Dimensions
Temperature Range
Security
Data rates
Specification
WMDQ-177ACN
Qualcomm QCA9892
PCI Express 1.1
DC 3.3V
2 x I-PEX connectors
30mmX 50.8mm
0 to 40 °C (Operating),
-30 to 70 °C (Storage)
WEP,TKIP,AES and WAPI hardware encryption
802.11b:1, 2, 5.5, 11Mbps
802.11g:6, 9, 12, 18, 24, 36, 48, 54Mbps
802.11n:
 20MHz channel:
 1Nss: 65Mbps @ 800GI, 72.2Mbps @ 400GI
(Max.)
 2Nss: 130Mbps @ 800GI, 144.4Mbps @ 400GI
(Max.)
 40MHz channel:
 1Nss: 135Mbps @ 800GI, 150Mbps @ 400GI
(Max.)
 2Nss: 270Mbps @ 800GI, 300Mbps @ 400GI
(Max.)
802.11a: 6, 9, 12, 18, 24, 36, 48, 54Mbps
802.11n:
 20MHz channel:
 1Nss: 65Mbps @ 800GI, 72.2Mbps @ 400GI
(Max.)
 2Nss: 130Mbps @ 800GI, 144.4Mbps @ 400GI
(Max.)
 40MHz channel:
 1Nss: 135Mbps @ 800GI, 150Mbps @ 400GI
(Max.)
 2Nss: 270Mbps @ 800GI, 300Mbps @ 400GI
(Max.)
802.11ac:
 20MHz channel:
 1Nss: 78Mbps @ 800GI, 86.7Mbps @ 400GI
(Max.)
 2Nss: 156Mbps @ 800GI, 173.3Mbps @ 400GI
(Max.)
 40MHz channel:
 1Nss: 180Mbps @ 800GI, 200Mbps @ 400GI
(Max.)
 2Nss: 360Mbps @ 800GI, 400Mbps @ 400GI
(Max.)

T x channel width
support
Standard/Compliance
RF Spec
Frequency Range
Radio Stream
Transmit Power
(Per Radio Stream)
Tolerance ( +/- 2dBm)
Receive Sensitivity
Tolerance ( +/- 2dBm)
80MHz channel:
 1Nss: 390Mbps @ 800GI, 433.3Mbps @ 400GI
(Max.)
 2Nss: 780Mbps @ 800GI, 866.7Mbps @ 400GI
(Max.)
20MHz / 40MHz /80MHz
IEEE 802.11b/g/n/ac
2.4G,5G
2T2R
802.11b 1Mbps 19 dBm
802.11g 6Mbps:18 dBm
802.11n HT-20 MCS0 :18 dBm
802.11n HT-40 MCS0 :12 dBm
802.11a 6Mbps: 19 dBm
802.11n HT20 MCS0: 18dBm
802.11n HT40 MCS0: 18dBm
802.11ac VHT20 MCS0: 18dBm
802.11ac VHT40 MCS0: 18dBm
802.11ac VHT80 MCS0: 12dBm
CCK 1Mbps :-90 dbm
OFDM 6Mbps -94dbm
OFDM 54M -80dbm
HT20 MCS0 : -94dbm
HT20 MCS7 :-78dbm
HT40 MCS0 : -90dbm
HT40 MCS7 : -76dbm
802.11a:
6Mbps: -94dbm
54M: -80dbm
802.11n HT20/HT40 @5G:
HT20 MCS0: -94dbm
HT20 MCS7: -76dbm
HT40 MCS0: -90dbm
HT40 MCS7: -76dbm
802.11ac VHT20/VHT40/VHT80:
VHT20 MCS0: -94dbm
VHT20 MCS8: -74dbm
VHT40 MCS0: -90dbm
VHT40 MCS9: -70dbm
VHT80 MCS0: -88dbm
VHT80 MCS9: -66dbm
Dimension : 50mm* 30mm (Full size)
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Country Code selection feature to be disabled for products marketed to the US/CANADA.
Operation of this device is restricted to indoor use only
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
and
2) The transmitter module may not be co-located with any other transmitter or antenna,
3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for
2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to
the end-user regarding to Regulatory Domain change.
As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed
IMPORTANT NOTE
In the event that these conditions can not be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC authorization is no longer considered valid and the
FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such
that 20 cm may be maintained between the antenna and users. The final end product must be labeled
in a visible area with the following: “Contains FCC ID: TVE-120506”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install
or remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
6
Industry Canada statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes:
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
This radio transmitter (IC: 7280B-120506) has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain
indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 7280B-120506) a été approuvé par Industrie Canada
pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain
est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur.
Antenna Model
C210-510579-A
Type
Connector
2.4G Gain
5G Gain
Dipole
R-SMA
2.8 dBi
3 dBi
Caution:
the device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
Avertissement:
les dispositifs fonctionnant dans la bande de 5150 à 5250MHz sont réservés
uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme Canada limites d'exposition aux radiations dans un environnement non
contrôlé. Cet équipement doit être installé et utilisé à distance minimum de 20cm entre le radiateur et
votre corps.
This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 1 condition above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes:
1) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 1 condition ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront
pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final
pour toutes exigences de conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or
co-location with another transmitter), then the Canada authorization is no longer considered valid and
the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and obtaining a separate
Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations
d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada
n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces
circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et
l'obtention d'une autorisation distincte au Canada.
End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains IC:7280B-120506”.
Plaque signalétique du produit final
Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC:
7280B-120506".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install
or remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la
façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui
intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et
avertissements comme indiqué dans ce manuel.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract
Create Date                     : 2015:09:07 11:18:57+08:00
Creator                         : Adobe Acrobat 11.0.12
Modify Date                     : 2015:09:07 11:20:21+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2015:09:07 11:20:21+08:00
Format                          : application/pdf
Title                           : User Manual_WMDQ-177ACN.xps
Document ID                     : uuid:e3a6cca6-ca29-49c2-9a12-d5c723b7fbf3
Instance ID                     : uuid:142cb3da-31c3-4340-96bf-3cac0ab13ba6
Creator Tool                    : Adobe XPS2PDF Lib
Producer                        : Adobe Acrobat 11.0.12 XPS Conversion Plug-in
Page Count                      : 10

EXIF Metadata provided by EXIF.tools