FreeWave Technologies PRW0010WP 2 Megapixel Wireless Bullet Camera User Manual My

FreeWave Technologies Inc. 2 Megapixel Wireless Bullet Camera My

Users Manual_rev.pdf

Part Number: LUM0078AARevision: Apr-2016WavePro™ WPV10-100™CameraUser Manual
Page 2 of 32 LUM0078AA Rev Apr-2016This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.Safety InformationThe products described in this manual can fail in a variety of modes due to misuse, age, or malfunction. Systemswith these products must be designed to prevent personal injury and property damage during product operationand in the event of product failure.WarrantyFreeWave Technologies, Inc. warrants the FreeWave® WPV10-100™ Camera (Product) against defects inmaterials and manufacturing for a period of one year from the date of shipment, depending on model number. Inthe event of a Product failure due to materials or workmanship, FreeWave® will, at its discretion, repair orreplace the Product. For evaluation of Warranty coverage, return the Product to FreeWave® upon receiving aReturn Material Authorization (RMA).In no event will FreeWave Technologies, Inc., its suppliers, or its licensors be liable for any damages arising fromthe use of or inability to use this Product. This includes business interruption, loss of business information, orother loss which may arise from the use of this Product.Warranty Policy will not apply in the following circumstances:1. If Product repair, adjustments, or parts replacements are required due to accident, neglect, or unduephysical, electrical, or electromagnetic stress.2. If Product is used outside of FreeWave® specifications as stated in the Product's data sheet.3. If Product has been modified, repaired, or altered by Customer unless FreeWave® specifically authorizedsuch alterations in each instance in writing.WPV10-100™ Return Material Authorization (RMA) Policy and ProceduresThis policy describes the responsibilities and procedures of the Customer and FreeWave when a WPV10-100™Product return is required.When a request for a WPV10-100™ Product replacement has been verified by FreeWave’s Customer Support,FreeWave’s policy for processing the device returned due to a fault is to replace the device with a new orrefurbished device upon receipt of the reported faulty product.FreeWave's RMA policy is subject to change without notice.In-Warranty Replacement Procedure1. Customer contacts FreeWave Customer Support to report the non-functioning WPV10-100™ Product .2. FreeWave Customer Support:a. Verifies that a Product replacement is the appropriate action.b. Issues a FreeWave RMA number.3. The Customer pays the shipping costs to return the WPV10-100™ Product to FreeWave.4. FreeWave sends a new or refurbished WPV10-100™ Product to the Customer.Important!: Any visual or external damage noted on a returned Product may void the warranty.This will be communicated back to the customer and a Purchase Order (PO) will be requested from thecustomer for Product replacement.FreeWave Technologies, Inc.5395 Pearl Parkway, Suite 100Boulder, CO 80301303.381.9200Toll Free: 1.866.923.6168Fax: 303.786.9948Copyright © 2016 by FreeWave Technologies, Inc.All rights reserved. www.freewave.com
WavePro™ WPV10-100™: User ManualExport NotificationFreeWave Technologies, Inc. products may be subject to control by the Export Administration Regulations(EAR) and/or the International Traffic in Arms Regulations (ITAR). Export, re-export, or transfer of theseproducts without required authorization from the U.S. Department of Commerce, Bureau of Industry andSecurity, or the U.S. Department of State, Directorate of Defense Trade Controls, as applicable, isprohibited. Any party exporting, re-exporting, or transferring FreeWave products is responsible forobtaining all necessary U.S. government authorizations required to ensure compliance with these and otherapplicable U.S. laws. Consult with your legal counsel for further guidance.FCC NotificationsThis device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) Thisdevice may not cause harmful interference and 2) this device must accept any interference received, includinginterference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference ina residential installation. This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one of the following measures:lReorient or relocate the receiving antenna.lIncrease the separation between the equipment and receiver.lConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.lConsult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliancecould void the user's authority to operate this equipment.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.The content of this guide covers FreeWave Technologies, Inc. models sold under FCC ID: KNYPRW0010WP.All models sold under the FCC ID(s) listed above must be installed professionally. Any changes or modificationsnot expressly approved by the party responsible for compliance could void the user's authority to operate thisequipment.This radio must not be co-located or operating in conjunction with any other antenna or radio. Operations in the5.15-5.25GHz band are restricted to indoor usage only.FCC Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Thisequipment should be installed and operated with minimum distance 20 cm between the radiator & your body.Power SourceInput voltage for the above models is 12V / 1A.Important!: Input power shall be derived from a single Class 2 power source.IC NotificationsThis device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following twoconditions: (1) this device may not cause interference, and (2) this device must accept any interference, includinginterference that may cause undesired operation of the device.Ce dispositif est conforme à la norme CNR-247 d'Industrie Canada applicable aux appareils radio exempts delicence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire deLUM0078AA Rev Apr-2016 Page 3 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
Page 4 of 32 LUM0078AA Rev Apr-2016This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptiblede provoquer un fonctionnement indésirable..IC Radiation Exposure StatementThis equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. Thisequipment should be installed and operated with minimum distance 20 cm between the radiator and your body.Professional Installation Instruction1. InstallationThis product is designed for specific application and needs to be installed by a qualified personal whohas RF and related rule knowledge. The general user shall not attempt to install or change the setting.2. Installation LocationThe product shall be installed at a location where the radiating antenna can be kept 20 cm from nearbyperson in normal operation condition to meet regulatory RF exposure requirement.3. External AntennaUse only the antennas which have been approved by the applicant. The non-approved antenna(s) mayproduce unwanted spurious or excessive RF transmitting power which may lead to the violation of IC limitand is prohibited.4. Installation ProcedurePlease refer to user’s manual for the detail.5. WarningPlease carefully select the installation position and make sure that the final output power does notexceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty.Instructions d'installation Professionnelle1. InstallationCe produit est destine a un usage specifique et doit etre installe par un personnel qualifie maitrisant lesradiofrequences et les regles s'y rapportant. L'installation et les reglages ne doivent pas etre modifies parl'utilisateur final.2. Emplacement d'installationEn usage normal, afin de respecter les exigences reglementaires concernant l'exposition auxradiofrequences, ce produit doit etre installe de facon a respecter une distance de 20 cm entre l'antenneemettrice et les personnes.3. Antenn externe.Utiliser uniiquement les antennes approuvees par le fabricant. L'utilisation d'autres antennes peutconduire a un niveau de rayonnement essentiel ou non essentiel depassant les niveaux limites definispar IC, ce qui est interdit.4. Procedure d'installationConsulter le manuel d'utilisation.5. AvertissementChoisir avec soin la position d'installation et s'assurer que la puissance de sortie ne depasse pas leslimites en vigueur. La violation de cette regle peut conduire a de serieuses penalites federales.Detachable Antenna UsageThis radio transmitter (IC: 2329B-PRW0010WP / Model: WPV10) has been approved by Industry Canada tooperate with the antenna type listed below with maximum permissible gain indicated. Antenna types notincluded in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited foruse with this device.
WavePro™ WPV10-100™: User ManualLe présent émetteur radio (IC: 2329B-PRW0010WP / Model: WPV10) a été approuvé par Industrie Canada pourfonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les typesd'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictementinterdits pour l'exploitation de l'émetteur.Approved Antenna(s) ListTypeGain (dBi)Connector2400MHz2450MHz2500MHzDipole 1.53 1.51 1.68 RSMAEurope – EU Declaration of ConformityThis device complies with the essential requirements of the R & TTE Directive 1999/5/EC. The following testmethods have been applied in order to prove presumption of conformity with the essential requirements of the R& TTE Directive 1999/5/EC:lEN60950-1 /A12:2011+A2:2013 - Safety of Information Technology EquipmentlEN50385:2002 - Product standard to demonstrate the compliance of radio base stations and fixedterminal stations for wireless telecommunication systems with the basic restrictions or the referencelevels related to human exposure to radio frequency electromagnetic fields (110MHz - 40GHz) - Generalpublic.lEN 300 328 V1.9.1:2015 - Electromagnetic compatibility and Radio spectrum Matters (ERM); WidebandTransmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and usingspread spectrum modulation techniques; Harmonized EN covering essential requirements under article3.2 of the R & TTE DirectivelEN 301 489-1 V1.9.2:2011 - Electromagnetic compatibility and Radio Spectrum Matters (ERM);ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Commontechnical requirementslEN 301 489-17 V2.2.1:2012 - Electromagnetic compatibility and Radio spectrum Matters (ERM);ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specificconditions for 2.4GHz wideband transmission systems and 5GHz high performance RLAN equipmentIn Italy the end-user should apply for a license at the national spectrum authorities in order to obtainauthorization to use the device for setting up outdoor radio links and/or for supplying public access totelecommunications and/or network services.This device may not be used for setting up outdoor radio links in France and in some areas the RF output powermay be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.Language DescriptionČesky[Czech]FreeWave Technologies, Inc. tímto prohlašuje, že tento WPV10-100™ je ve shodě sezákladními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.Dansk[Danish]Undertegnede FreeWave Technologies, Inc. erklærer herved, at følgende udstyrWPV10-100™ overholder de væsentlige krav og øvrige relevante krav i direktiv1999/5/EF.Deutsch[German]Hiermit erklärt FreeWave Technologies, Inc., dass sich das Gerät WPV10-100™ inÜbereinstimmung mit den grundlegenden Anforderungen und den übrigeneinschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.LUM0078AA Rev Apr-2016 Page 5 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
Page 6 of 32 LUM0078AA Rev Apr-2016This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.Language DescriptionEesti[Estonian]Käesolevaga kinnitab FreeWave Technologies, Inc. seadme WPV10-100™ vastavustdirektiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teisteleasjakohastele sätetele.English Hereby, FreeWave Technologies, Inc., declares that this WPV10-100™ is in compliancewith the essential requirements and other relevant provisions of Directive 1999/5/EC.Español[Spanish]Por medio de la presente FreeWave Technologies, Inc. declara que el WPV10-100™cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables oexigibles de 1999/5/CE.Ελληνική[Greek]ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ FreeWave Technologies, Inc. ΔΗΛΩΝΕΙ ΟΤΙ WPV10-100™ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.Français[French]Par la présente FreeWave Technologies, Inc. déclare que l'appareil WPV10-100™ estconforme aux exigences essentielles et aux autres dispositions pertinentes de ladirective 1999/5/CE.Italiano[Italian]Con la presente FreeWave Technologies, Inc. dichiara che questo WPV10-100™ èconforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva1999/5/CE.Latviski[Latvian]Ar šo FreeWave Technologies, Inc. / izgatavotāja nosaukums] deklarē, ka WPV10-100™atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiemnoteikumiem.Lietuvių[Lithuanian]Šiuo FreeWave Technologies, Inc. deklaruoja, kad šis WPV10-100™ atitinka esminiusreikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.Nederlands[Dutch]Hierbij verklaart FreeWave Technologies, Inc. dat het toestel WPV10-100™ inovereenstemming is met de essentiële eisen en de andere relevante bepalingen vanrichtlijn 1999/5/EG.Malti[Maltese]Hawnhekk, FreeWave Technologies, Inc., jiddikjara li dan WPV10-100™ jikkonformamal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva1999/5/EC.Magyar[Hungarian]Alulírott, FreeWave Technologies, Inc. nyilatkozom, hogy a WPV10-100™ megfelel avonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.Polski[Polish]Niniejszym FreeWave Technologies, Inc. oświadcza, że WPV10-100™ jest zgodny zzasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy1999/5/EC.Português[Portuguese]FreeWave Technologies, Inc. declara que este WPV10-100™ está conforme com osrequisitos essenciais e outras disposições da Directiva 1999/5/CE.Slovensko[Slovenian]FreeWave Technologies, Inc. izjavlja, da je ta WPV10-100™ v skladu z bistvenimizahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.Slovensky[Slovak]FreeWave Technologies, Inc. týmto vyhlasuje, že WPV10-100™ spĺňa základnépožiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.Suomi[Finnish]FreeWave Technologies, Inc. vakuuttaa täten että WPV10-100™ tyyppinen laite ondirektiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojenmukainen.Svenska[Swedish]Härmed intygar FreeWave Technologies, Inc. att denna WPV10-100™ står Iöverensstämmelse med de väsentliga egenskapskrav och övriga relevantabestämmelser som framgår av direktiv 1999/5/EG.
WavePro™ WPV10-100™: User ManualGNU License NotificationSome of the software in the firmware is licensed under the GNU General Public License and other Open Sourceand Free Software licenses. You can obtain corresponding source by contacting FreeWave and requesting thesource on CD.Restricted RightsAny product names mentioned in this manual may be trademarks or registered trademarks of their respectivecompanies and are hereby acknowledged.This manual is only for use by purchasers and other authorized users of FreeWave products.No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical,or for any purpose without the express written permission of FreeWave Technologies, Inc. FreeWave reservesthe right to make changes to this manual without notice. FreeWave assumes no responsibility or liability for theuse of this manual or the infringement of any copyright or other proprietary right.WPV10-100™ Product SafetyWPV10-100™ Conditions of Safe UselProvision shall be made to prevent the rated voltage from being exceeded by the transient disturbancesof more than 140% of the peak rated voltage.lThe shall be mounted with a minimum IP54 ingress protection rating (as defined in EN-60529).lThe WPV10-100™ CANNOT be used in an environment greater than pollution degree 2.LUM0078AA Rev Apr-2016 Page 7 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
Page 8 of 32 LUM0078AA Rev Apr-2016This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
WavePro™ WPV10-100™: User ManualTable Of ContentsPreface 101. WPV10-100™ Camera Overview 121.1 System Requirements 131.2 WPV10-100™ Camera Included Accessories 131.3 User-supplied Equipment 141.4 WPV10-100™ Camera Hardware Layout 142. WPV10-100™ Camera Installation and Setup 152.1 Connect to the WPV10-100™ Camera 162.2 Setup the Computer IP Address Configuration 182.3 Access the WPV10-100™ Camera 22Appendix A: WPV10-100™ Camera Technical Specifications 28Appendix B: WPV10-100™ Camera LEDs 31LUM0078AA Rev Apr-2016 Page 9 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
WavePro™ WPV10-100™: User ManualPrefaceWhere to Find Additional InformationWPV10-100™ Quick Start GuideUse the WP201™ website, WavePro™ Downloads, to download the latest version of the QuickStart Guide.Contacting FreeWave Technical SupportFor up-to-date troubleshooting information, check the Support page at www.freewave.com.FreeWave provides technical support Monday through Friday, 8:00 AM to 5:00 PM MountainTime (GMT -7).lCall toll-free at 1.866.923.6168.lIn Colorado, call 303.381.9200.lContact us through e-mail at moreinfo@freewave.com.Printing this DocumentThis document is set to print double-sided with a front cover and a back cover. Viewing thisdocument online with a PDF viewer, may show pages intentionally left blank to accommodate thedouble-sided printing.LUM0078AA Rev Apr-2016 Page 10 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
PrefacePage 11 of 32 LUM0078AA Rev Apr-2016This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.Document StylesThis document uses these styles:lFreeWave applications appear as: FreeWave.lParameter setting text appears as: [Page=radioSettings]lFile names appear as: configuration.cfg.lFile paths appear as: C:\Program Files (x86)\FreeWave Technologies.lUser-entered text appears as: xxxxxxxxx.l3rd-party names appear as: Notepad®.Caution: Indicates a situation that MAY cause damage to personnel, the radio, data, ornetwork.Example: Provides example information of the related text.FreeWave Recommends: Identifies FreeWave recommendation information.Important!: Provides semi-cautionary information relevant to the text or procedure.Note: Emphasis of specific information relevant to the text or procedure.Provides time saving or informative suggestions about using the product.Warning! Indicates a situation that WILL cause damage to personnel, the radio, data, ornetwork.Documentation FeedbackSend comments or questions about this document's content to techpubs@freewave.com. In thee-mail, include the title of the document or the document's part number and revision letter (foundin the footer).
WavePro™ WPV10-100™: User Manual1. WPV10-100™ Camera OverviewThank you for purchasing the WavePro™WPV10-100™ Camera.The FreeWave WPV10-100™ is a 2-Megapixel Day & Night wireless Bullet Network Camerawhich adds monitoring and surveillance capabilities to a variety of network environments. With abuilt-in removable mechanical IR-cut filter, it helps users keep an eye on what matters and getnotified by what just happened on demand allowing remote 24/7 monitoring.The WPV10-100™ features:lMegapixel HD with High speed H.264 encoding ensures high quality image recording.lLED Infrared Night Vision (to a maximum of 82 feet (25 meters)) with Automatic ActivationSystem to deliver 24/7 non-stop monitoring.lWireless 802.11b/g/n Network Compliant with optimum Wi-Fi performance.lSupports:lTwo simultaneous stream recording with high speed H.264 encoding.lPush Message and Play Back on smart devices triggered by motion.NoteslFeatures and specifications are subject to change without notice.lTrademarks and registered trademarks are the property of their respective owners.LUM0078AA Rev Apr-2016 Page 12 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
1. WPV10-100™ Camera OverviewPage 13 of 32 LUM0078AA Rev Apr-2016This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.1.1 System RequirementsThese are the system requirements needed to configure the WPV10-100™:lComputer with:lan Ethernet interface or wireless network capabilitylWindows® 7 or greater.lBroadband Internet Service (Cable or DSL Modem)lWeb browser (i.e., Internet Explorer®, Firefox®, Safari®, Chrome®, Opera®).1.2 WPV10-100™ Camera Included AccessoriesThe WPV10-100™ package contains these items:WPV10-100™ Included AccessoriesQty Description Image Letter1WPV10-100™ Quick Start Guide1WPV10-100™ Camera A1 2.4GHz, 2dBi, Omni-directional, detachable Antenna B1 Power Adapter C1 Screw Set Kit D1 RJ-45 cable EFigure 1: WPV10-100™ Included Accessories
WavePro™ WPV10-100™: User Manual1.3 User-supplied EquipmentlComputer with:lWindows®7or greaterlan Ethernet portlInternet browser (Chrome®, Firefox®, Internet Explorer®, Opera®, Safari®)lCAT5e / CAT6 Ethernet cablelMedium Phillips-head screwdriverlHammer (for wall installation)lDrill with 8mm diameter drill bit (for wall installation)1.4 WPV10-100™ Camera Hardware LayoutThis image identifies the hardware layout of the WPV10-100™:Figure 2: WPV10-100™ Camera Hardware LayoutNote: See WPV10-100™ Camera Included Accessories (on page 13).LUM0078AA Rev Apr-2016 Page 14 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
WavePro™ WPV10-100™: User Manual2. WPV10-100™ Camera Installation and SetupThis section provides procedure information about installation and initial setup of the WPV10-100™.lConnect to the WPV10-100™ Camera (on page 16)lSetup the Computer IP Address Configuration (on page 18)lAccess the WPV10-100™ Camera (on page 22)LUM0078AA Rev Apr-2016 Page 15 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
2. WPV10-100™ Camera Installation and SetupPage 16 of 32 LUM0078AA Rev Apr-2016This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.2.1 Connect to the WPV10-100™ Camera1. Screw the antenna onto the WPV10-100™.Figure 3: Antenna on the WPV10-100™2. Connect the camera to the computer using the Ethernet cable.3. Connect the supplied power cable from the camera to a power outlet.
WavePro™ WPV10-100™: User ManualFigure 4: WPV10-100™ Connect to Power Outlet and ComputerLUM0078AA Rev Apr-2016 Page 17 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
2. WPV10-100™ Camera Installation and SetupPage 18 of 32 LUM0078AA Rev Apr-2016This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.2.2 Setup the Computer IP Address ConfigurationNote: The images in this example procedure are for (missing or bad snippet).1. On the computer, click the Windows®Start button and select Control Panel.2. View the Control Panel window by Category and click Network and Internet > ViewNetwork Status and Tasks.3. Click the Change Adapter Settings link.Figure 5: Change Adapter Settings Link4. Double-click the Local Area Connection link.Figure 6: Local Area Connection LinkThe Local Area Connection Status dialog box opens.
WavePro™ WPV10-100™: User ManualFigure 7: Local Area Connection Status dialog box5. Click Properties.The Local Area Connection Properties dialog box opens.6. Select the Internet Protocol Version 4 (TCP/IPv4) option.LUM0078AA Rev Apr-2016 Page 19 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
2. WPV10-100™ Camera Installation and SetupPage 20 of 32 LUM0078AA Rev Apr-2016This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.Figure 8: Local Area Connection Properties dialog box7. Click Properties.The Internet Protocol Version 4 (TCP/IPv4) Properties dialog box opens.8. Make a note of the current settings (to reverse this procedure later).9. Select the Use the following IP address option button.10. In the IP Address text box, enter an IP Address that is in the same subnet range but aDIFFERENT IP Address than the WPV10-100™ AND different than the computer IPAddress.Note: The default WPV10-100™ Camera IP Address is 192.168.1.200. The default subnetmask is 255.255.255.0.Example: Enter an IP Address from 192.168.1.1 to 192.168.1.254 (but NOT 192.168.1.200)and the Subnet Mask to 255.255.255.0.
WavePro™ WPV10-100™: User ManualFigure 9: Local Area Connection Properties dialog boxNote: An IP Address is NOT required in the Default Gateway text box.11. Click OK to save the changes and close the dialog box.12. Click Close twice to close the Local Area Connection Properties and Local AreaConnection Status dialog boxes.LUM0078AA Rev Apr-2016 Page 21 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
2. WPV10-100™ Camera Installation and SetupPage 22 of 32 LUM0078AA Rev Apr-2016This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.2.3 Access the WPV10-100™ Camera1. On the computer connected to the WPV10-100™, open a web browser.2. In the address bar of the browser, enter the default WPV10-100™ IP Address:192.168.1.200.Figure 10: Entered IP Address3. Press <Enter>.The Login window opens.Figure 11: WPV10-100™ Login window4. Enter the default Username and Password (admin for both) and click Login.Note: When accessing the WPV10-100™ the first time, the WebCMS download windowopens.
WavePro™ WPV10-100™: User ManualFigure 12: WebCMS Download window5. Click the Download WebCMS button.The Opening webCMS_n.n.n.n.exe dialog box opens.Figure 13: Opening webCMS_n.n.n.n.exe dialog box6. Click Save File.The Enter name of file to save to dialog box opens.LUM0078AA Rev Apr-2016 Page 23 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
2. WPV10-100™ Camera Installation and SetupPage 24 of 32 LUM0078AA Rev Apr-2016This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.Figure 14: Enter name of file to save to dialog box7. Click Save.The Enter name of file to save to dialog box closes.8. Open the location where the webCMS_n.n.n.n.exe file was saved.Figure 15: Designated folder in Windows®Explorer9. Select and double-click the webCMS_n.n.n.n.exe.The User Account Control message opens.
WavePro™ WPV10-100™: User ManualFigure 16: User Account Control message10. Click Yes.Note: If the browser is still open, a WebCMSLive message appears.Figure 17: WebCMSLive message11. Close any open browsers and repeat Steps 9 and 10.The WebCMSLive Setup: Installing window opens showing the installation process hasstarted.When installation is completed, the WebCMSLive Setup message appears.Note: The installation and setup happens very quickly. The software is installed here:C:\Program Files (x86)\WebCMS.LUM0078AA Rev Apr-2016 Page 25 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
2. WPV10-100™ Camera Installation and SetupPage 26 of 32 LUM0078AA Rev Apr-2016This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.Figure 18: WebCMSLive Setup message12. Click OK to close the messages.13. Open a web browser.14. In the address bar of the browser, enter the default WPV10-100™ IP Address:192.168.1.200.Figure 19: Entered IP Address15. Press <Enter>.The Login window opens.Figure 20: WPV10-100™ Login window16. Enter the default Username and Password (admin for both) and click Login.17. Press <Enter>.
WavePro™ WPV10-100™: User ManualThe WPV10-100™Camera Home Page opens showing a live-action stream to thecomputer.Figure 21: WPV10-100™ Camera Home PageNote: See the Window Components for detailed information about the options in the window.Note: : If a gray color is visible in the viewer, it is because the camera has detected insufficientof light in the room and enabled night vision mode automatically. Point the camera to a brighterarea, to see it switched to normal color mode.Try a few places to see how the switch from normal color mode to night vision works.LUM0078AA Rev Apr-2016 Page 27 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
WavePro™ WPV10-100™: User ManualAppendix A: WPV10-100™ CameraTechnical SpecificationsSpecifications may change at any time without notice. For the most up-to-date specificationsinformation, see the product's data sheet available at www.freewave.com.WPV10-100™ Camera Technical SpecificationsSpecification DescriptionCameraImage Sensor 1/2.7”, 1920x1080 pixel, Progressive Scan CMOSLENs Fixed Focal, f=2.8mm / F1.8F.O.V. 120°Day / Night Removable IR-cut filterMinimum Illumination lColor (IR-off): 0.1Lux / F1.8lB/W (IR-On): 0 Lux / F1.8IR Illuminator 12 IR LEDs with a maximum of 25m rangeShutter Time 1/2 sec. to 1/10,000 secVideoCompression H.264 / MJPEG / MPEG4Frame Rates A maximum of 30fps at 1920x1080Image Settings lImage SizelQualitylBit RatelBrightnesslContrastlSaturationLUM0078AA Rev Apr-2016 Page 28 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
Appendix A: WPV10-100™ Camera Technical SpecificationsPage 29 of 32 LUM0078AA Rev Apr-2016This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.WPV10-100™ Camera Technical SpecificationsSpecification DescriptionlFlip and MirrorlAGC / AWB / AESlDay / Night, Manual or Auto ModelText Caption OverlaylSharpnesslExposurelTime StampWeb Browser lChrome®lFirefox®lInternet Explorer®lOpera®lSafari®View Clients Live viewing for a maximum of 2 clients.Alarm and Event / RecordingEvent Trigger lMotion or Audio-In DetectionlPre-alarm and post-alarm (5 sec)Event Notification Email / Push-NotificationEvent Actions lSchedule RecordinglFile upload to SAMBA / FTPNetworkingNetwork 10/100 Mbps Ethernet, RJ-45PoE 802.3af Class2Security lAdmin / User Account Level, Password ProtectedlWEP / WPA / WPA2-PSKProtocoll3GPPlDDNSlDHCPlDNSlFTPlHTTPlIPv4lNFS / Samba clientlNTPlPPPoElQoS / DSCPlRTPlRTSPlSMTPlTCPlUDPlUPnPExternal Antenna Gain 1.68dBiRF Connector Reverse SMA plugWireless Interface IEEE 802.11b/g/nPower
WavePro™ WPV10-100™: User ManualWPV10-100™ Camera Technical SpecificationsSpecification DescriptionPower Requirements lPower Supply: 12VDC, 1.0A (power from adapter)lPoE: 54VDC, 0.6A, 802.3afPower Consumption 8WEnvironmentalOperating Temperature -20°C to 50°C-4°F to 122°FHumidity Up to 100%, CondensingDimensions Length (including bracket): 9.25 inches (23.5cm)Diameter of Bracket: 3.0 inches (7.62cm)Diameter of Camera: 1.75 inches (4.45cm)Weight 7 lbs3.2kgInterface Cable lRJ-45 1 x 10/100BASE-T(802.3af PoE)lDC Jack (12V / 1A)lReset ButtonCompliance StandardsRadio Approvals l47 CFR Part 15lIC RSS-247lCEMaterial Compliance lRoHSlIP66 EnclosureLUM0078AA Rev Apr-2016 Page 30 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.
WavePro™ WPV10-100™: User ManualAppendix B: WPV10-100™ Camera LEDsThese are the WPV10-100™ LEDs:WPV10-100™ Camera LEDsFunction Button LEDWPS 1~5 sec Green – Blink (RJ45)Reset 6~10 sec Orange – Solid (RJ45)Reset to Default 10 sec or above Orange – Blink (RJ45)LUM0078AA Rev Apr-2016 Page 31 of 32This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned byFreeWave. This document cannot be reproduced in whole or in part by any means without written permission fromFreeWave Technologies, Inc.

Navigation menu