FreeWave Technologies PRW1001EC 802.11an PCIe Module User Manual My

Download:
Mirror Download [FCC.gov]
Document ID	2097350
Application ID	37PY2yKCN1H2M/7+l84lvw==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	44.81kB (560169 bits)
Date Submitted	2013-10-21 00:00:00
Date Available	2014-04-19 00:00:00
Creation Date	2017-10-25 11:58:07
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-25 11:58:07
Document Title	My Document
Document Creator	Microsoft® Word 2010
Document Author:	hnix

FreeWave W5800-01 RF Module
Guide
Part Number: LFC0003AA
Revision: A
Last Updated: 08/20/213
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 26 cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or transmitter.
OEM Integration Conditions
This device is intended only for OEM integrators under the following conditions:
1.
2.
3.
The antenna must be installed such that 20 cm is maintained between the antenna and users, and
The antenna must be installed such that 26 cm is maintained between the dish antenna and users
The transmitter module may not be co-located with any other transmitter or antenna
As long as the above are met, further transmitter test will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements required with this module
installed
IMPORTANT! In the event that these conditions cannot be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC authorization is no longer considered valid and
the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
List of certificated antennas
Model
Type
5150~5.850MHz
MPE Distance
Y5815
Yagi
15 dBi
20 cm
ZDAQJ5800-12
Omni
12 dBi
20 cm
P250-5.8
Panel
14.4 dBi
20 cm
ZDAGP5800-24-12
Dish
24 dBi
26 cm
Dipole
7 dBi
20 cm
98618UNXX000
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 26 cm may
be maintained between the antenna and users.
The final end product must be labeled in a visible area with the following:
Contains FCC ID: KNYPRW1001EC .
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this
RF module in the user manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
1.
2.
This device may not cause interference, and
This device must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
1.
2.
l'appareil ne doit pas produire de brouillage, et
('utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Caution: (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for
harmful interference to co-channel mobile satellite systems;
Avertissement: (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une
utilisatio à l’i t ieu afi de dui e les is ues de ouillage p judi ia le au s st es de satellites o iles utilisa t
les mêmes canaux;
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 26 cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 26 cm de distance entre la source de
rayonnement et votre corps.
OEM Integration Conditions
This device is intended only for OEM integrators under the following conditions:
1.
The transmitter module may not be co-located with any other transmitter or antenna.
As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements required with this module
installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes:
1.
Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 1 condition ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires.
Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de
conformité supplémentaires requis pour ce module installé.
IMPORTANT: In the event that these conditions cannot be met (for example certain laptop configurations or colocation with another transmitter), then the Canada authorization is no longer considered valid and the
IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible
for re-evaluating the end product (including the transmitter) and obtaining a separate Canada
authorization.
IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations
d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du
Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans
ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur)
et l'obtention d'une autorisation distincte au Canada.
End Product Labeling
The fi al e d p odu t ust e la eled i a isi le a ea ith the follo i g: Co tai s IC:2329B-PRW1001EC .
Plaque signalétique du produit final
Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:
"Contient des IC: 2329B-PRW1001EC".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this
RF odule i the use ’s a ual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer
ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme
indiqué dans ce manuel.
This radio transmitter (identify the device by certification number, or model number if Category II) has been approved
by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required
antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 2329B-PRW1001EC) a été approuvé par Industrie Canada pour fonctionner avec les
types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type
d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont
strictement interdits pour l'exploitation de l'émetteur.
FreeWave Technologies, Inc.
5395 Pearl Parkway, Suite 100
Boulder, CO 80301 USA
303.381.9200
www.FreeWave.com
Introduction
This do u e t des i es the appli a ilit of use ope atio of F eeWa e’s W5800-01 RF module to keep
compliance with regulatory requirements.
Host System
This odule is i te ded to e used o l
regulated voltage to the module.
ith F eeWa e’s s ste
p odu ts. F eeWa e’s s ste
ust suppl
Antenna Usage
This odule a o l e used ith the t pe of a te as app o ed to e used ith F eeWa e’s s ste . The
use of a higher gain or a different type of antenna than the antennas approved ith F eeWa e’s FCC
submission requires new FCC approval.
The antennas used with this module may only be collocated and placed as identified on the FCC grant.
Certificated Antennas
Model
Type
5150~5.850MHz
Y5815
Yagi
15 dBi
ZDAQJ5800-12
Omni
12 dBi
P250-5.8
Panel
14.4 dBi
ZDAGP5800-24-12
Dish
24 dBi
Dipole
7 dBi
98618UNXX000
Module Label
The host system containing this module must either:

Make the module label visible so the FCC ID is visible in the installation

Label the end system product with the FCC ID and IC ID of the module
Professional Installation Instructions
1. Installation personnel
This product is designed for specific applications and needs to be installed by qualified personnel who
have RF and related rule knowledge. The general user shall not attempt to install or change settings.
2. Installation location
The product shall be installed at a location where the radiating antenna can be kept 26 cm from nearby
persons in normal operation condition to meet regulatory RF exposure requirement.
3. External antenna
Use only the antennas that have been approved by the applicant. A non-approved antenna(s) may
produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC
limit and is prohibited.
4. Installation procedure
This module ust e p ofessio all i stalled ithi F eeWa e’s host s ste . This module uses a
standard PCI express electrical and data interface. The host in which this module is integrated provides a
stable 3.3 VDC power to this module through a regulator circuit. This module when plugged into the
host system doesn’t require any additional power supply and uses the host’s power supply. Plugging
other type of power supply that does ’t meet the specification will damage the module.
5. Install Position and Output Power
Carefully select the installation position and make sure that the final output power does not exceed the
limit set force in relevant rules. The violation of the rule could lead to serious federal penalty.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract
Author                          : hnix
Create Date                     : 2013:10:01 18:09:03-06:00
Modify Date                     : 2013:10:02 13:44:33+08:00
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : hnix
Title                           : My Document
Creator Tool                    : Microsoft® Word 2010
Metadata Date                   : 2013:10:02 13:44:33+08:00
Producer                        : Microsoft® Word 2010
Document ID                     : uuid:923d6f1d-b3d6-4df6-bd16-0299fd85d406
Instance ID                     : uuid:1391a903-869d-4f75-aca4-90efb577885a
Page Count                      : 7

EXIF Metadata provided by EXIF.tools