Frigidaire FEX831CS0 User Manual LAUNDRY CENTER Manuals And Guides L0304056

FRIGIDAIRE Laundry Centers Manual L0304056 FRIGIDAIRE Laundry Centers Owner's Manual, FRIGIDAIRE Laundry Centers installation guides

User Manual: Frigidaire FEX831CS0 FEX831CS0 FRIGIDAIRE LAUNDRY CENTER - Manuals and Guides View the owners manual for your FRIGIDAIRE LAUNDRY CENTER #FEX831CS0. Home:Laundry & Garment Care Parts:Frigidaire Parts:Frigidaire LAUNDRY CENTER Manual

Open the PDF directly: View PDF .
Page Count: 8

Installation

Instructions

Full Size Laundry Center

Gas & Electric

Before beginning installation, carefully read these instructions. This will simplify the installation

and ensure the laundry center is installed correctly and safely. Leave these instructions near the

laundry center after installation for future reference.

NOTE: The electrical service to the laundry center must conform with local codes and ordinances

and the latest edition of the National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian

Electrical Code, CSA C22.1

NOTE: The gas service to the laundry center must conform with local codes and ordinances and

the latest edition of the National Fuel Gas Code ANSI Z223.1/NFPA 54, or in Canada, the Canadian

Natural Gas and Propane Installation Code, CSA B149. 1.

NOTE: The laundry center is designed under ANSI Z21.5.1 or ANSI/UL 2158- CAN/CSA C22.2

(latest edition) for HOME USE only. This laundry center is not recommended for commercial

applications such as restaurants or beauty salons, etc.

For your safety the information in

this manual must be followed to minimize the risk

of fire or explosion or to prevent property damage,

personal injury or loss of life.

- Do not store or use gasoline or other flammable

vapors and liquid in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

e Do not try to light any appliance.

t Do not touch any electrical switch; do not use

any phone in your building.

e Clear the room, building or area of all

occupants.

e Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

e If you cannot reach your gas supplier, call the

fire department.

Installation and service must be preformed by a

qualified installer, service agency or the gas

supplier.

Contents

SUBJECT PAGE

Pre-lnstallation Requirements

Electrical Requirements

Water Supply Requirements

Drain Requirements

Exhaust System Requirements

Gas Supply Requirements

Location

Mobile Home Installation

Rough-In Dimensions

Unpacking

Electrical Installation

Grounding Requirements

3 & 4-Wire Connections

Installation

Replacement Parts

Printed in U,S,A. P/N131661700 (O11O)

PRE-INSTALLATION REQUIREMENTS

Tools and Materials Required for Installation:

1. Phillips head screwdriver.

2. Channel-lock adjustable pliers.

3. Carpenter's level.

4. Flat or straight blade screwdriven

5. Duct tape.

6. Rigid or flexible metal 4 inch (10.16 cm) duct.

7. Vent hood.

8. Pipe thread sealer (Gas).

9. Ratchet with 3/8 inch (0.96 cm) socket.

ELECTRICAL REQUIREMENTS

ELECTRICLaundry Center

Circuit- Individual 30 amp branch circuit fused with 30 amp

minimum time delay fuses or circuit breakers.

POWER SUPPLY- 3-wire or 4-wire, 240 volt, single phase, 60

Hz, Alternating Current.

POWER SUPPLYCORD KIT-The laundry center MUST employ

a 3-condutor power supply cord NEMA 10-30 type SRDTrated

at 240 volt AC minimum, 30 amp, with 3 open end spade lug

connectors with upturned ends or closed loop connector OR a

4-condutor power supply cord NEMA 14-30 type SRDTor ST

(as required) rated at 240 volt AC minimum, 30 amp, with 4

open end spade lug connectors with upturned ends or closed

loop connectors and marked for usewith clothes dryers. If being

installed in a manufactured (mobile) home, the laundrycenter

MUST employ a 4-condutor power supply cord NEMA 14- 30

type SRDTor ST (as required) rated at 240 volt AC minimum,

30 amp, with 4 open end spade lug connectors with upturned

ends or closed loop connectors and marked for use with clothes

dryers. See ELECTRICAL CONNECTIONS. (Canada - 4-wire

power supply cord is installed on laundry center.)

OUTLET RECEPTACLE- NEMA 10-30R (3-wire) receptacle or

NEMA 14- 30R (4-wire) receptacle to be located so the power

supply cord is accessible when the laundry center is in an

installed position.

POWER SUPPLY CORD -The gas laundry center is equipped

with a 120 volt 3-wire power cord.

NOTE: Do not under

any circumstances

remove grounding

prong from plug.

\Grounding Prong

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed within 42 inches

(106.68 cm) of your laundry center's water inlet. The faucets

MUST be 3/4 inch (1.9 cm) garden hose type so inlet hoses can

be connected. Water pressure MUST be between 10 and 120

pounds per square inch (maximum unbalance pressure, hot vs.

cold, 10 psi). Your water department can advise you of your

water pressure. The hot water temperature should be about

140 degrees E

DRAIN REQUIREMENTS

1. Drain capable of eliminating 17 gals. per minute.

2. A standpipe diameter of 1-1/4 inches (3.18 cm) minimum.

3. The standpipe height above the floor should be:

Minimum height: 33 inches (83.82 cm)

Maximum height: 96 inches (244 cm)

96"Max.

(244 cm)

-"T"-

33" Min. __L

NEMA 10-30R NEMA 14-30R

IGAS Laundry Center I

CIRCUIT -individual15 amp branch circuit fused with a 15 amp

maximum time delay fuse or circuit breaker.

NOTE:For installations requiring a longer drain hose, have a

qualified technician install a longer hose PIN131461201,

available from an authorized parts distributor. For drain

systems in the floor, install a siphon break kit, available

from your local hardware store.

POWER SUPPLY -3 wire, 120 volt single phase, 60 Hz,

Alternating Current,

EXHAUST SYSTEM REQUIREMENTS

Use only 4inch (10.16 cm) diameter (minimum) rigid or flexible

metal duct and approved vent hood which has a swing-out

damper(s) that opens when the dryer is in operation. When the

dryer stops, the damper(s) automatically closes to prevent drafts

and the entrance of insects and rodents. To avoid restricting the

outlet, maintain a minimum of 12 inches (38.5 cm) clearance

between the vent hood and the ground or any other obstruction.

The following are specific requirements

for proper and safe operation of your laundry center,

Failure to follow these instructions can create excessive

drying times and fire hazards.

Do not use plastic flexible duct to exhaust

the dryer, Excessivelint can build up inside the exhaust system

and create a fire hazard and restrict air flow, Restricted air flow

will increase drying times. If your present system is made up of

plastic duct or metal foil duct, replace it with a rigid or flexible

metal duct, Ensure the present duct is free of any lint

prior to installing laundry center dryer duct.

If the dryer is not exhausted outdoors, some

fine lint will be expelled into the laundry area, An accumulation

of lint in any area of the home can create a health and fire

hazard. The dryer exhaust system MUST be exhausted to

the outside of the dwelling!

Do allow combustible materials

not (for

example: clothing,draperies/curtains, paper) to come in contact

with the exhaust system, The dryer MUST NOT be exhausted

into a chimney, a wall, a ceiling, or any concealed space of a

building which can accumulate lint, resulting in a fire hazard.

Do not exceed the length of duct pipe or

number of elbows allowed in the" EXHAUST DUCT LENGTHS"

chart. Lint can accumulate in the system, plugging the system

and creating a fire hazard, as well as increasing drying times.

Do not screen the exhaust ends of the vent

system, nor use any screws or rivets to assemble the exhaust

swstem, Lint can become caught in the screen, on the screws

or rivets, clogging the exhaust system and creating a fire hazard

as well as increasing drying times. Use an approved vent hood

to terminate the duct outdoors, and seal all joints with duct

tape. All male duct pipe fittings MUST be installed downstream

with the flow of air.

Explosion hazard. Do not install the laundry

center where gasoline or other flammables are kept or stored,if

the laundry center is installed in a garage, it must be a minimum

of 18 inches (45.7 cm) above the floor. Failure to do so can

result in death, explosion, fire or burns.

The exhaust system back pressureMUST not exceed 0,6 inches

(1.52 cm) of water column, measured with an inclined

manometer at the point the exhaust connects to the dryer,

The exhaust system should be inspected and cleaned a

minimum of every two years with normal usage. The more the

dryer is used, the more often you should check the exhaust

system and vent hood for proper operation.

The maximum length ofthe exhaust system depends upon

the type of duct used, number of elbows and type of exhaust

hood,

The maximum length for both rigid and flexible duct is shown

in the chart below.

EXHAUST DUCT LENGTHS

EXHAUST HOOD TYPE

Tums 25"

Louvered (6

MAXIMUM LENGTH OF 4-INCH (10.2 CM)

DIAMETER RIGID METAL DUCT

56 tt (1707 m) 42 [t (128 m)

46 tt (1402 m) 36 tt (1097 m)

34 tt (1036 m) 28 [t (853 m)

32 ft (975 m) 18 ft (548 m)

MAXIMUM LENGTH OF 4-INCH (10.2 CM)

DIAMETER FLEXIBLE METAL DUCT

0 30 ft (914 m) 22 ft (67 m)

1 22 ft {67 m) 14tt (427 m)

2 16 tt (488 m) 10 tt (305 m)

3 10 tt (30S m) S tt (15 m)

The laundry center may be exhausted four (4) ways with

rear flush installation:

1Straight back

2. Down (8 inch [20.32 cm[ length of 4 inch [10.16 cm]

rigid duct and 1 elbow down)

3. Left (8 inch [20.32 cm] length of 4 inch [10.16 cm]

rigid duct, 1 elbow down and 1 elbow left)

4. Right (8 inch [20,32 cm] length of 4 inch [10,16 cm]

rigid duct, 1 elbow down and 1 elbow right)

Toexhaust up, add an 11 inch (27,94 cm) length of standard

4 inch (10,16 cm) diameter duct and a 90° elbow. The unit

will be positioned about 4Y, inches (11.43 cm) away from

the wall (flush to wall exhausting may be done by going

below the dryer then sideways).

An exhaust hood positioned to line up with the dryer exhaust

can be installed directly through the outside wall, ]o exhaust

to the side or down, add an 8 inch (20.32 cm) length of

standard 4 inch (10,16 cm) diameter duct and a 90° elbow,

GAS SUPPLY REQUIREMENTS

1. Installation MUST conform with local codes, or in the

absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1 (latest edition) or in Canada, the

current AN/CGA B149.

2. The gas supply line should be of 1/2 inch (1.27 cm) pipe,

3. If codes allow, flexible metal tubing may be used to connect

your dryer to the gas supply line. The tubing MUST be

constructed of stainless steel or plastic-coated brass.

4. The gas supply line MUST have an individual shutoff valve.

5. A 1/8 inch (0,32 cm) N. R T. plugged tapping, accessible

for test gage connection, MUST be installed immediately

upstream of the gas supply connection to the dryer.

6. The dryer and its individual shutoff valve MUST be

disconnected from the gas supply piping system during

any pressure testing of the gas supply piping system at

test pressures equal to or less than 1/2 psig (3.45 kPa).

7. The dryer MUST be isolated from the gas supply piping

system by closing its individual manual shutoff valve during

any pressure testing of the gas supply piping system at

test pressures equal to or less than 1/2 psig (3.45 kPa).

LOCATION OF YOUR LAUNDRY CENTER

DO NOT INSTALL YOUR LAUNDRY CENTER:

1, In an area exposed to dripping water or outside weather

conditions.

2, In an area where it will come in contact with curtains or

drapes.

3, On carpet, Floor MUST be solid with a maximum slope of 1

inch (2,54 cm).

INSTALLATION IN RECESSOR CLOSET

1, A laundry center installed in a bedroom, bathroom, recess

or closet, MUST be exhausted outdoors,

2, No other fuel burning appliance shall be installed in the

same closet as the Gas laundry center.

3, Your laundry center needs the space around it for proper

ventilation,

DO NOT INSTALLYOUR LAUNDRY CENTERIN A CLOSET

WITH A SOLID DOOR.

4, A minimum of 120 square inches (774,2 square cm) of

opening, equally divided at the top and bottom of the door,

is required. Air openings are required to be unobstructed

when a door is installed. A Iouvered door with equivalent

air openings for the full length of the door is acceptable,

5, The following illustrations show minimum clearance

dimensions and air openings for proper operation in a recess

or closet installation.

0_N

MOBILE HOME INSTALLATION

1. Dryer MUST be exhausted outside (outdoors, not

beneath the mobile home) using metal ducting that

will not support combustion, Metal ducting must be 4

inches (10,16 cm) in diameter with no obstructions,

Rigid metal duct is preferred.

2, If dryer is exhausted through the floor and area beneath

the mobile home is enclosed, the exhaust system MUST

terminate outside the enclosure with the termination

securely fastened to the mobile home structure.

3, Referto page 3 for other important venting requirements.

4, When installing a gas dryer into a mobile home, a

provision must be made for outside make up air This

provision is to be not lessthan twice the area of the

dryer exhaust outlet.

5, Installation MUST conform to current Manufactured

Home Construction & Safety Standard (which is a

Federal Regulation Title 24 CFR-Part32-80) or when

such standard isnot applicable, with American National

Standard for Mobile Homes. In Canada, the CSA Z240

is applicable,

The laundry center is designed under

ANSI Z 21.5.1 for HOME USE only.

Closet Door

ROUGH-IN DIMENSIONS

75 Y_IN

(19177 CM)

54 5/16 IN

(13795 CM)

43 IN

(10922 CM)

ELECTRICAL

CONNECTION O

WATER iNLETS _fO

(REAR)

I_ DRAIN OUTLET

f (REAR)

\__ 3Y_IN

(9 52 CM)

hJ hJ

27 IN

(68 58CM)

GASSUPPLY

PiPE(REAR)

5Y41N l

_1333 CM)

43 IN

_( (1O922 eM)

104417_41NM)

29 7/16 iN

(7477 CM)

361/16iN

(9160 CM)

u u

I1_ 30 13/16 IN

(7826 CM)

Return laundry center to al, up, ,N, ,L position,

2YzlN

4t_ (6 35 CM)

1 7/8 iN

It-- (476 CM)

4 13/16 iN

(12 22 CM)

11 7/16 IN

(295 CM)

UNPACKING

1, Using the four shipping carton corner posts (two on each

side), carefully lay the laundry center on its left side and

remove foam shipping base.

2, Using ratchet with 3/8 inch (0,96 cm) socket, remove

mechanism shipping bolt and plastic spacer block from

center of base.

NOTE: If the laundry center is to be transported at a

later date, the tub blocking pad, shipping bolt, and

plastic spacer block should be retained.

PLASTICSPA(

4, Remove:

(a) roam tub blocking pad,

(b) roam shipping blocks from rear of unit.

(d) foam dryer support pads.

(e) inlet hoses.

(f) enclosure package,

5, From the back of the washer, remove the wire shipping

clips securing the drain hose and power cord (if equipped).

Plastic clamps secure the drain hose to the right side of the

washer backsheet, These clamps form a standpipe to

prevent water syphoning. DO NOT REMOVE THESE

CLAMPS.

6, Carefully move the laundry center to within 4 feet (1,22 m)

of the final location to begin the installation,

MECHANI!

SHIPPING

BOLT

G CARTON CORNER POSTS

FOAM

SHIPPING

PAD

:)OWER CORD

(IFEQUIPPED)

DSE

ELECTRICAL INSTALLATION

ALL ELECTRICLaundry Centers

he following are specific requirements

fe electrical installation of your laundry

center. Failure to follow these instructions can create

electrical shock and/or afire

hazard

_T'_ L_;f-_tlt_ll_B This appliance MUST beproperly

grounded. Electrical shock can result if the laundry center is

not properly grounded, Follow the instructions in this manual

for proper grounding.

_Do not use an extension cord with this

laundry center. Some extension cords are not designed to

withstand the amounts of electrical current this laundry center

utilizes and can melt, creating electrical shock and/or fire

hazard, Locate the laundry center within reach of the receptacle

for the length power cord to be purchased, allowing some

slack in the cord. Refer to the pre-installation requirements in

this manual for the proper power cord to be purchased.

_A U,L. approved strain relief must be

installed onto power cord, If the strain relief is not attached,

the cord can be pulled out of the laundry center and can be cut

by any movement of the cord, resulting in electrical shock,

Do not use an aluminum wired receptacle

with a copper Wired power cord and plug (or vice versa). A

chemical reaction occurs between copper and aluminum and

can causeelectrical shorts, The proper wiring and receptacle

is a copper wired power cord with a copper wired

receptacle OR aluminum wired power cord with an

aluminum wired receptacle,

NOTE: Laundry centers operating on a 208 volt power supply

will have longer drying times than laundry centers operating

on a 240 volt power supply.

GROUNDING REQUIREMENTS

Non-Canadian ELECTRICLaundry Center

_ Improper connection of the equipment

grounding conductor can result in a risk of electrical shock.

Check with a licensed electrician if you are in doubt as to

whether the appliance is properly grounded.

For a grounded, cord-connected laundry center:

1, The laundry center MUST be grounded, In the event of

malfunction or breakdown, grounding will reduce the risk

of electrical shock by a path of least resistance for electrical

current.

2, If your laundry center is equipped with a power supply cord

having an equipment-grounding conductor and a grounding

plug, the plug MUST be plugged into an appropriate, copper

wired receptacle that is properly installed and grounded in

accordance with all local codes and ordinances. If in doubt,

call a licensed electrician,

For a permanently connected laundry center:

The laundry center MUST be connected to a grounded metal,

permanent wiring system;oran equipment grounding conductor

MUST be run with the circuit conductors and connected to the

equipment-grounding terminal or lead on the appliance,

Canadian ELECTRICLaundry Center

_lmproper connection of the equipment

grounding conductor can result in a risk of electrical shock.

Check with a licensed electrician if you are in doubt as to

whether the appliance is properly grounded,

For a grounded cord connected laundry center:

1, The laundry center MUST be grounded, In the event of

malfunction or breakdown, grounding will reduce the risk

of electrical shock by providing a path of least resistance

for the electrical current,

2, Since your laundry center is equipped with a power supply

cord having an equipment-grounding conductor and a

grounding plug, the plug MUST be plugged into an

appropriate outlet that is properly installed and grounded

in accordance with all codes and ordinances, If in doubt,

call a licensed electrician

ALL GAS Laundry Centers

1, The laundry center, when installed, MUST be electrically

grounded in accordance with local codes, or in the absence

of local codes, with the National Electrical Codes, ANSI/

NFPA(latest edition) or in Canada, CSA C22.1 Canadian

Electrical Code Part 1,

2. The laundry center is equipped with a three-prong (grounding)

plug for your protection against shock hazard and should

be plugged directly into a properly grounded three-prong

receptacle, Do not cut or remove the grounding prong from

the plug,

ELECTRICAL CONNECTIONS

FOR A 3-WIRE SYSTEM

IELECTRICLaundry Center

1, Remove the screw securing the

terminal block access cover to the

rear panel and remove cover.

2, Install a U.L approved strain relief

connector in the entry hole on the

back panel.

3, Insert a NEMA 10-30 Type SRDI,

Ui. approved power cord

through the strain relief,

4, Attach the power cord neutral (central wire) conductor to

the silver colored center terminal on the terminal block,

Tighten the screw securely.

6, Attach the white (neutral) wire from the power cord and the

green ground wire from the appliance harness to the silver-

colored center terminal on the terminal block. Tighten the

screw securely.

Green Ground

Screw /Silver Terminal

Conductor

(Cord) Terminal Block

Green Ground

Wire "White

_Black

7, Attach the red and black wires from the power cord to the

outer brass-colored terminals on the terminal block. Tighten

both screws securely.

8, Tighten the screws securing the cord restraint firmly against

the power cord,

9, Reinstall the terminal block access coven

5,Attach the remaining two power cord outer conductors to

the outer brasscolored terminals on the terminal block,Tighten

both screw securely,

&Tighten the screws securing the cord restraint against

the power cord,

7, Reinstall the terminal accesscover

ELECTRICAL CONNECTIONS

FOR A 4-WIRE SYSTEM

IELECTRICLaundry Center

1, Remove the screw securing the

terminal block accesscover to the

rear panel and remove cover.

2, Install a U.L approved strain relief

connector in the entry hole on the

back panel,

3, Remove the green neutral ground wire

from the green ground screw located above the termial

block,

4, Insert a NEMA 14-30 Type STor SRDT,U,L, approved power

cord through the strain relief,

5, Attach the green power cord ground wire to the cabinet

with the green ground screw

INSTALLATION

1, Run some water from the hot and cold faucets to flush the

water lines and remove particles that might clog up the

water valve screens.

2, Check inlet hoses to ensure the rubber washers are installed

in each end,

3, Carefully connect the inlet hoses to the water valve (on the

left side of the washer cabinet), tic hten by hand, then tighten

another 2/3 turn with pliers,

_DO NOT CROSS THREAD OR OVERTIGHTEN

THESECONNECTIONS.

4, Determine which water faucet is the HOT water faucet and

carefully connect the bottom inlet hose to the HOT water

faucet, tighten by hand, then tighten another 2/3 turn with

pliers, Carefully connect the top inlet hose to the COLD

water faucet, tighten by hand, then tighten another 2/3 turn

with pliers.

DO NOT CROSS THREAD OR OVERTIGHTEN

ECTIONS. Turn the water on and check for leaks

at both connections,

5, Carefully move the laundry center to its final location,

6, ]o ensure the laundry center is level and solid on all four

legs, tilt the laundry center forward so the rear legs are

off the ground. Gently set the laundry center back down to

allow the rear legsto self adjust. Placea level on top of the

washer Check it side to side, then front to back. Screw the

front leveling legs up or down to ensure the laundry center

is resting solid on all four legs (no rocking of the laundry

center should exist).

NOTE: Keep the leg extension at a minimum to prevent

excessive vibration.

7,GASCONNECTION(Gas laundry centers only)

a. Remove the shipping cap from gas pipe at the rear of the

dryer,

NOTE: DO NOT connect the laundry center to LR gas service

without converting the gas valve. An LR conversion kit (P/

N 5303937053) must be installed by a qualified gas

technician.

b. Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or approved

pipe from the gas supply line to the 3/8 inch (0.96 cm) pipe

located on the back of the dryer, Use a 1/2 inch (1.27 cm) to

3/8 inch (0.96 cm) reducer for the connection. Apply an

approved thread sealerthat isresistant to the corrosive action

of liquefied gases on all pipe connections.

c. Open the shutoff valve in the gas supply line.

d. Test all connections by brushing on a soapy water solution.

NEVERTEST FORGAS LEAKSWITH AN OPEN FLAME.

8. Form a " U " shape on the end of the drain hose with the

hose pointed toward the drain. Place the formed end in a

laundry tub or astandpipe and securewith acable tie provided

in the enclosure package, WATER WILL SYPHON FROM

THE WASHER IF THE ABOVE INSTRUCTIONS ARE NOT

FOLLOWED,

9. Remove the two (2) screws securing the dryer front access

panel to the dryer cabinet. Lift the panel until the tabs can

be disengaged from the cabinet, Remove the panel and set

aside,

Access

anel

Screws

10. Connect the exhaust duct to outside duct work, Use duct

tape to seal all joints,

11. Plug the power cord into a grounded outlet,

NOTE: Check to ensure the power is off at acircuit breaker/

ruse box before plugging the power cord into an outlet,

12.T_ at a circuit breaker/fuse box.

Before operating the dryer, make sure

the dryer area _sclear and free from combustible materials,

gasoline, and other flammable vapors, Also see that nothing

(such as boxes, clothing, etc.) obstructs the flow of

combustion and ventilation air,

13. Reinstall the dryer front access panel.

14. Run the washer and dryer though a cycle, Check for proper

operation.

NOTE: On gas dryers, before the burner will light, it is

necessary for the gas line to be bled of air, If the

burner does not light within 45 seconds the first time

the dryer is turned on, the safety switch will shut

the burner off. If this happens, turn the timer to

"OFF" and wait 5 minutes before making another

attempt to light,

15. If your laundry center does not operate, please review the

"Avoid Service Checklist" located in your Owner's Guide

before calling for service.

16, Placethese instructions in a location near the laundry center

for future reference.

NOTE: A wiring diagram is located behind the dryer front

access panel. REPLACEMENT PARTS

If replacement parts are needed for your laundry center, contact

the source where you purchased your laundry center.

I!!_IKI_,!_I Destroy the carton, plastic bags, and metal

band after the laundry center is unpacked. Children might use

them for play Cartons covered with rugs, bedspreads, or plastic

sheets can become airtight chambers causing suffocation. Place

all materials in a garbage container or make materials

inaccessible to children,

_ Label all wires prior to disconnection when

servicing controls. Wiring errors can cause improper and

dangerous operation, Verify proper operation after servicing.

[he instructions in this manual and all other

this laundry center are not meant to

cover every possible condition and situation that may occur.

Good safe practice and caution MUST be applied when

installing, operating and maintaining any appliance.

Maximum benefits and enjoyment are achieved when all

the Safety and Operating instructions are understood and

practiced as a routine with your laundry tasks,

Frigidaire FEX831CS0 User Manual LAUNDRY CENTER Manuals And Guides L0304056

FRIGIDAIRE Laundry Centers Manual L0304056 FRIGIDAIRE Laundry Centers Owner's Manual, FRIGIDAIRE Laundry Centers installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation