Frigidaire GLTF1670AS0 User Manual WASHER Manuals And Guides L0410185
FRIGIDAIRE Residential Washers Manual L0410185 FRIGIDAIRE Residential Washers Owner's Manual, FRIGIDAIRE Residential Washers installation guides
User Manual: Frigidaire GLTF1670AS0 GLTF1670AS0 FRIGIDAIRE WASHER - Manuals and Guides View the owners manual for your FRIGIDAIRE WASHER #GLTF1670AS0. Home:Laundry & Garment Care Parts:Frigidaire Parts:Frigidaire WASHER Manual
Open the PDF directly: View PDF 
.
Page Count: 5
| Download | |
| Open PDF In Browser | View PDF |
i ( ( Installation Instructions Full Size Tumble Action Washers Before beginning installation, carefully read these instructions• This will simplify the installation and ensure the washer is installed correctly and safely. Leave these instructions near the washer after installation for future reference. NOTE: The electrical service to the washer must conform with local codes and ordinances and the latest edition of the National Electrical Code, ANSIINFPA 70 or in Canada, CSA C22.1 Canadian Electrical Code Part 1. Contents For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or loss of life. - Do not store or use gasoline or other flammable vapors and liquid in the vicinity of this or any other appliance. - WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Clear the room, building or area of all occupants. • Immediately call your gas supplier from a neighbor's phone. Follow the gas suppliers instructions. SUBJECT PAGE Pre-lnstallation Requirements Electrical Requirements Grounding Requirements Water Supply Requirements Drain Requirements Rough-In Dimensions LocationOf Your Washer Unpacking Installation Replacement Parts 2 2 2 2 2 3 4 4 5 5 • If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency or the gas supplier. Printed in U.S.A. PIN 131997600 (0010) PRE-INSTALLATION 1. 2. 3, 4. 5. 6. 7, REQUIREMENTS in accordancewith all local codes and ordinances or inthe absence of local codes, withthe National Electrical Codes, ANSI/NFPA 70 (latest edition). If in doubt, call a licensed electrician. DONOT cut off or alter the groundingprong on the power supply cord. In situations where a two-slot receptacle is present, it is the owner's responsibility to have a licensed electrician replace it with a properly grounded three prong grounding type receptacle. Tools Required for Installation: 1/4 in. nut driver 3/8 in. socket with ratchet. 3/8 in. open end wrench. 7/16 in. socketwith ratchet. 9/16 in. open end wrench. Channel-lock adjustable pliers. Carpenter's level. ELECTRICAL WATER REQUIREMENTS CIRCUIT - Individual,properly polarized and grounded 15 amp. branch circuit fused with 15 amp, time delay fuse or circuit breaker• POWER SUPPLY- 2 wire,with ground, 120 volt,single phase, 60 Hz, Alternating Current. OUTLET RECEPTACLE - Properlygrounded 3-prong receptacle to be located so the power supply cord is accessiblewhen the washer is in an installed position. SUPPLY REQUIREMENTS Hot and cold water faucets MUST be installedwithin 42 inches (107 cm) of your washer's water inlet. The faucets MUST be 3/4 inch (1.9 cm) garden hose type so inlet hoses can be connected. Water pressure MUST be between 10 and 120 pounds per square inch (maximum unbalance pressure, hot vs. cold, 10 psi.) Your water department can advise you of your water pressure.The hot water temperature shouldbe about 140 degrees F (60 degrees C). DRAIN 1. 2. REQUIREMENTS Drain capable of eliminating 17 gals (64.3 L) per minute. A standpipe diameter of 1-1/4 in. (3.18 cm) minimum. 3. The standpipe heightabove thefloor shouldbe: Minimum height: 24 in. (61 cm) Maximum height: 96 in. (244 cm) --,9 o GROUNDING 96 in. (244 cm) Max. REQUIREMENTS Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is propedy grounded. 24 in. (61 cm) Min. 1. The washer MUST be grounded. In the event of malfunctionor breakdown, groundingwillreduce the risk of electrical shock by a path of least resistance for electrical current. NOTE: 2. Since your washer is equipped with a power supply cord having an equipment-grounding conductorand a groundingplug, the plug MUST be plugged into an appropriate, copper wired receptacle that is properlyinstalledand grounded Drain hose attached to the washer can reach a 58 in. (147 cm) high standpipe. For higher standpipe use hose PIN 131461201, available from an authorized parts distributor. If drain is less than 24 in. (61 cm), install a siphon break kit, available at your local hardware store. ROUGH-IN DIMENSIONS 26% 17 (43.2) i 2 (5,1) .< |_ 24 3/4 _' -- (67.9) 60 _, (I52.4)-- (7.3) 2% I (2.54_ (62.9) ] I F o I ] m 36 i (91.5) (3.81) ii__ I I \ , 'i_ Cord Power 331,_ _ (65) Water Under Counter 31% (80.3) 34% (87.9) _______ ]nlete BACK SIDE L 1 _ m J R inch(cm) RollerWheels AdjustableLegs UNDER COUNTER INSTALLATION If an under counter* installationis desired, the washer MUST have a top sheet kit installed, PIN 131445600. Kit is available from an authorized parts distributor. *Custom sized countertop is required. ,__ 60 ___ (43.2) 263.4 (152.4) 24% (62.9) <------(67.9) / (2.54) 43% 0 (110.7) ] I ! m BAc SIDE inch (cm) AdjustableLegs RollerWheels 3 1 LOCATION OF YOUR WASHER DO NOT INSTALL YOUR WASHER: 1. In an area exposed to dripping water or outside weather conditions. The ambient temperature should never be below 60 degrees F (15.6 degrees C) for proper washer operation. 2. In an area where it will come in contact with curtains or drapes. 3. In an area (garage or garage-type building)where gasoline of other flammables are kept or stored (includingautomobiles). 4. On carpet. Floor MUST be solidwith a maximum slope of 1/2 in. per foot (1.27 cm per 30.5 cm). To ensure vibration or movement does not occur, reinforcement of the floor may be necessary. 3. 4. Remove the styrofoam base. Carefully return the washer to an upright position and remove the carton. 5. Carefullymove the washer to within4 feet (122cm) of the final location. 6. Remove the following from the back side of the washer: 4 bolts, 4 yellow plastic spacers, 3 metal "P" clamps. 7. Remove the service panel from the front of the washer. 8. Remove the 4 nutsand 6 large washers that attach the 2 yellow shipping braces to the drum and the base. Lift up on the drum and remove the braces (a yellow ribbon surrounds the items to be removed).These braces mustbe removedto allow the power supply cord to be released from the shippingring. 9. Remove the large styrofoam block located under the drum. Lift up on the drum, tilt the base of the foam block inwards toward the rear of the washer until free, then pull it out. 10. Remove and discard the yellow ribbon and label from the front of the washer. MINIMUM INSTALLATION CLEARANCES When installed in alcove or closet: Sides, Rear = 0 in. (0 crn) Top = 0 in. (0 cm) Front Console Model Top = 15 in. (38.1 cm) Rear Console Model When installed in closet: Front = 1 in. (2.54 cm) Closet door ventilationrequired: 2 Iouvered openings each 60 irf (387 cmZ),3 in. (7.6 cm) from top and bottom of door. UNPACKING 1. 2. Cut the shippingcartonalong the dotted line along the base of the unit. While in the cartoncarefully lay the washer on its back side. 11. From the rear of the washer, carefully pull out the power supply cord through the hole in the backsheet. 12. Replace the service panel and screws. (_ (_ , BOLT SPACER NOTE: Ifthe washer is to be transported at a later date, the shippingsupporthardware must be reinstalled to prevent shipping damage. Retain the hardware in the plastic bag provided. "P" CLAMP 4 INSTALLATION I. 2. 3, 4. 5. 6. 7. Run some water from the hot and cold faucets to flush the water lines and remove particles that might clog up the water valve screens. Remove the inlet hoses and rubber washers from the plastic bag and install the rubber washers in each end of the inlet hoses. (90" elbow end) Carefully connect the inlet hose marked "HOT" to the outside "H"outlet of the water valve. Tighten by hand, then tighten another 2/3 turn with pliers, Carefully connect the other inlet hose to the inside "C" outlet of the water valve. Tighten by hand, then tighten another 2/3 turn with pliers. Do not crossthread or over-tighten these connections, Connect the inlet hose ends to the HOT and COLD water faucets tighfiy by hand, then tighten another 2/3 turnwith pliers. Turn the water on and check for leaks. NOTE: Use only new hoses. Carefully move the washer to its final location. Rollers on the rear of the washer allow for easy movement in undercounter installations. Gently lift up on the front of the washer and slide back. NOTE: Lifting up more than 1/8" will engage the rear legs. Do not use the dispenser drawer or door to liftwasher. With the washer in its final position, place a level on top of the washer (if an undercounter installation, no rocking of the washer should exist). Adjust the front leveling legs up or down to ensure the washer is resting solid.Turn the lock nuts on each leg up towards the base of the washer and snug with a wrench. NOTE: Keep the leg extension at a minimum to prevent excessive vibration. The farther out the legs are extended the more the washer will vibrate. The washer is designed to operate resting on its rear rollers. If the floor is not level or is damaged, the rear leveling legs may have to be extended. For undercounter installations, rear leg adjustment is accessible through the front service panel. Form a U shape on the end of the drain hose with the hose pointed toward the drain. Place in a laundry tub Cable Tie or standpipe and secure with the cable tie provided in the enclosure package. NOTE: If the drain hose is placed in a standpipe without forming a U shape, a siphoning action could occur. There must be an air gap around the drain hose. A snug hose fit can also cause a siphoning action. 8. Plug the power cord into a grounded outlet. NOTE: Check to ensure the power is off at a circuit breaker/fuse box before plugging the power cord into an outlet. 9. Turn on the power at a circuit breaker/fuse box. 10.Read the Operating Instructions and Owner's Guide provided with the washer. They contain valuable and helpful information that will save you time and money. 11.Run the washer through a complete cycle. Check for water leaks and proper operation. 12. If your washer does not operate, please review the "Avoid Service Checklist" in your Owner's Guide before calling for service. 13. Place these instructions in a location near the washer for future reference. NOTE: A wiring diagram is located inside the washer on the service panel, REPLACEMENT PARTS If replacements parts are needed for your washer, contact the sourcewhere you purchased yourwasher or cell 1-800-944-9044 for the Frigidaire Company Authorized Parts Distributor nearest you. Destroy the carton and plastic bags afterthe washer is unpacked.Children might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Place all matedals in a garbage container or make materials inaccessible to children. I&l_ll, R_q_qvm r l'=vw-'l_='n=_'==='l The instructionsin this manual and all other literature includedwiththis washer are not meant to cover every possible condition and situationthat may occur. Good safe practice and caution MUST be appliedwhen installing,operatingand maintainingany appliance. Maximum benefits and enjoyment are achieved I when all the Safety and Operating instructions are understood and practiced as a routine with your laundering tasks. I
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 5 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Fri Apr 20 14:59:16 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools