Fujitsu Ftp 628 Series Users Manual P128 139
FTP-628MCL001/002/003/004 ftp-628mcl001_002_003_004 Datasheet - Fujitsu United States
2015-01-25
: Fujitsu Fujitsu-Ftp-628-Series-Users-Manual-218996 fujitsu-ftp-628-series-users-manual-218996 fujitsu pdf
Open the PDF directly: View PDF 
.
Page Count: 12
1
NOT FOR NEW
DESIGN
FTP-628 Series
■OVERVIEW
The FTP-628 MCL Series is ultra compact high speed, battery
driven thermal printer, printing on 2-inch wide paper (58mm).
Paper can be easily set by an original platen release mecha-
nism.
The FTP-628 MCL series can be used for a variety of
applications, such as portable terminals, POS, ticket issuing
terminals, label printers, banking terminals, and measurement
and medical equipment.
■HIGHLIGHTS
• Ultra compact
Height 15.5 mm, width 69.9 mm, depth 35.7 mm
• High speed printing
It can print at 60 mm/s (480 dotlines/s) maximum by using
Fujitsu's unique head drive control.
• High resolution printing / Kanji supported
8 dots/mm of resolution printing is possible.
• Easy paper setting
Our unique platen release mechanism allows a
wide paper route even if the printer is ultra-compact, so
paper can be easily inserted. Auto loading is also available
on the MCL001 and MCL003 models.
• Two types of paper routes
Front and bottom paper feed.
• Easy mounting
Head, motor, sensor and other component wiring are unified
to one flexible cable, and the mechanism can be secured by
one hook and two screws at two locations, making mounting
easy.
BATTERY DRIVE, 2” HIGH SPEED THERMAL PRINTER
2
FTP-628MCL Series
NOT FOR NEW
DESIGN
■PART NUMBERS
■ SPECIFICATIONS
Part number FTP-628MCL001/002/003/004
Printing method Thermal-line dot method
Dot structure 384 dots/line
Dot pitch (Horizontal) 0.125 mm (8 dots/mm)—Dot density
Dot pitch (Vertical) 0.125 mm (8 dots/mm)—Line feed pitch
Effective printing area 48 mm
Number of columns ANK 32 columns/line (maximum 12x 24 dot font)
Paper width 58 mm+0
Paper thickness 60 to 80 µ m (some paper in this range may not be used because of
paper characteristics
Printing Speed Maximum 60mm/sec. (480 dot line/sec.)
Alphanumeric, katakana: 159 types
International and special characters: 195 types
JIS Kanji level 1, level 2, non-Kanji
(supported only by FTP-628DSL102): about 6800 types
12 × 24 dots, (1.5 × 3.0 mm), 32 columns: alphanumeric, katakana
24 × 24 dots, (3.0 × 3.0 mm), 16 columns: alphanumeric, katakana, Kanji
8 × 16 dots, (1.0 × 2.0 mm), 48 columns: alphanumeric, katakana
16 × 16 dots, (2.0 × 2.0 mm), 24 columns: alphanumeric, katakana, Kanji
SpecificationsItem
Character types
Character, dimensions (H×W), number of
columns
metIrebmuNtraP
msinahcemretnirP
hctiwsnoitcetednepodaehtuohtiwnoitresnirepaptnorf(100LCM826-PTF hctiwsnoitcetednepodaehtuohtiwnoitresnirepapmottob(200LCM826-PTF )bonkdnahctiwsnoitcetednepodaehhtiwnoitresnirepaptnorf(300LCM826-PTF )hctiwsnoitcetednepodaehhtiwnoitresnirepapmottob(400LCM826-PTF
gnivirdrofISL101UC826-PTF
ecafretnI
draoB
ylnoKNA )elbaliavateyton(100LSD826-PTF
ijnaK
detroppus ijnaKdnayromemhsalfhtiwscinortneC/laireslasrevinU201LSD826-PTF
-1
3
FTP-628MCL Series
NOT FOR NEW
DESIGN
■ SPECIFICATIONS
metInoitacificepS
ecafretnI scinortneC/C232SRotsmrofnoC
rewoP
ylppus
daehtnirproF :oitartnirp(A)3.1(97.0,tnerrucegarevaCDV5.8-2.4
eulavkaepehtsi)().ces/mm06:deepstnirp,%5.21
rotomrettucdnaretnirproFmumixamA1,CDV5.8-2.4
cigolroFmumixamA5.0,%5±CDV5
snoisnemiD
msinahcemretnirPnwoddaeh)HxDxW(mm5.51x3.43x6.96
draobecafretnImm42x99x131
)msinahceM(thgieW )bonktuohtiw(g35yletamixorppA
efildaeH
ruorednu(tod/seslupnoillim001:ecnatsiseresluP
)snoitidnocdradnats mk05ecnatsidgnilevartrepap:ecnatsisernoisarbA
)sselro%52:oitartnirp(
gnitarepO
tnemnorivne
erutarepmetgnitarepO ,egnarecnarussaytisnedgnitnirp(C˚04+otC˚5+
)C˚04+otC˚0taelbissopsinoitarepo
ytidimuhgnitarepO)noitasnednocon(HR%58ot02
erutarepmetegarotS)dedulcnitonrepap(C˚06+otC˚02-
ytidimuhegarotS)noitasnednocon(HR%59-5
noitceteD
noitcnuf
erutarepmetdaeH
noitceted
rotsimrehtybdetceteD
noitcetedkram/tuorepaP)sledomlla(retpurretni-otohpybdetceteD
noitcetedpudaeH)ylno400,300(hctiws-orcimybdetceteD
repapevitisneslamrehtdednemmoceR
)repaPnoppiN(4E-SK05FT:repapevitisneshgiH
-)repaPnoppiN(E-SK06FT:repapdradnatS
4010P020-PTF/100UP020-PTF
-)repaPijO(R051DP
1070P020-PTF
:repapegarotsefilmuideM
-)repaPnoppiN(1F-SK06FT
2010P020-PTF
)repaPijO(R071DP
)repaPihsibustiM(1-BBV022P
)repaPijO(H3-CB56HP
:repapegarotsefilgnoL
)repaPijO(N-R061DP
)repaPihsibustiM(532-PFA
4
FTP-628MCL Series
NOT FOR NEW
DESIGN
■FUNCTION
metImetI
.1noitcnuftnirptseT.8noitcetedytilamronbarettuC
.2noitcetedtuorepaP.9noitcnufgnivasrewoprotoM
.3noitceteddneraenrepaP.01noitcnufnoitcetedkraM
.4noitcetedpudaeH.11noitcetedytilamronbanoitarepoUCM
.5 ytilamronbaerutarepmetdaehlamrehT
noitceted .21noitcetorpecneuqesFFO/NOrewoP
.6noitcetedesuftuo-wolB.31noitcetorptnerruc-revorotoM
.7noitcetedytilamronbaegatlovdaeH.41remiterawdraH
■DIMENSIONS
1. Printer mechanism
Unit: mm
Platen Open
Platen Close
Paper Insertion
Platen Open
Platen Close
Paper Insertions
Center of Paper
Center of Paper
when open
when close)
15.5
Note: 1. Dimensions are nominal value (tolerance ±5 unless otherwise specified).
2. Platen unit (lever, platen, etc) moves by approximately 0.7mm toward paper insertion direction when platen is
open.
5
FTP-628MCL Series
NOT FOR NEW
DESIGN
2. Interface board
Unit: mm
130.8
83.8
55.9
6.4
5.1
88.9
78.7
39.4
5.1
30.591.4
120.7
5.1
39.4
4 - ø 3.6±0.1
CN1
CN6*
CN8**CN7CN3
CN2
Part mounting side
Part solder side
* CN6 not used
** CN8 used for paper near end detection
17.0
5.0
1.6
6
FTP-628MCL Series
NOT FOR NEW
DESIGN
■PRINTER CONNECTOR (FLEXIBLE PT BOARD) PIN ARRAYS
Control circuit side connector: 52030-3010 Molex or equivalent product (Reference CN3)
No. Signal I/O Contents No. Signal I/O Contents
1 PHK — Photo interrupter (cathode) 2 VSEN I
Power supply for paper sensor
3 PHE O Photo interrupter (emitter) 4VH I
Head driving power supply
5VH I
Head driving power supply
6 GNC —
Ground for head
7 GND —
Ground for head
8 DIN I
Data input
9 LAT I Data latch 10 CLK I
Clock
11 STB6 I Enable 6 12 STB5 I
Enable 5
13 STB4 I Enable 4 14 VDD I
Logic Power supply
15 STB3 I Enable 3 16 STB 2 I
Enable 2
17 STB1 I Enable 1 18 TH O
Thermistor
19 TH O Thermistor 20 GND —
Ground for head
21 GND —
Ground for head
22 VH I
Head driving power supply
23 VH I
Head driving power supply
24 N.C. —
Open terminal
25 SW1 I Head open switch* 26 SW2 O Head open switch*
27 MT/B I Stepping motor coil 28 MT/B I Stepping motor coil
excitation signal B excitation signal B
29 MT/A I Stepping motor coil 30 MT/A I Stepping motor coil
excitation signal A excitation signal A
* on MCL003 and MCL004 models
7
FTP-628MCL Series
NOT FOR NEW
DESIGN
No. Signal I/O Contents No. Signal I/O Contents
1 PRSTB I Data strobe 2 PRSTB-RET —
Connected to logic GND
3 PRDT0 I Data 0 4 PRDT0-RET —
Connected to logic GND
5 PRDT1 I Data 1 6 PRDT1-RET —
Connected to logic GND
7 PRDT2 I Data 2 8 PRDT2-RET —
Connected to logic GND
9 PRDT3 I Data 3 10 PRDT3-RET —
Connected to logic GND
11 PRDT4 I Data 4 12 PRDT4-RET —
Connected to logic GND
13 PRDT5 I Data 5 14 PRDT5-RET —
Connected to logic GND
15 PRDT6 I Data 6 16 PRDT6-RET —
Connected to logic GND
17 PRDT7 I Data 7 18 PRDT7-RET —
Connected to logic GND
19 ACKNLG O Data input acknowledge 20 ACKNLG-RET —
Connected to logic GND
21 BUSY O Busy 22 BUSY-RET —
Connected to logic GND
23 RINF2 O Printer status 2 24 INPRM-RET —
Connected to logic GND
25 SLCTIN I Printer select 26 INPRM I Reset
27 RINF1 O Printer status 1 28 RINF3 O Printer status 3
29 ATF I Paper feed request 30 GND — Logic GND
Notes:
• Symbol “——” means a negative logic signal.
• “–RET” signal is a return signal of the twisted pair cable.
• “I” or “O” means a signal direction from the interface board side.
(3) Connector pin number (4) Data input signal timing
FCN-605Q030-G/M (Fujitsu Components)
(2) Connector pin assignment
■INTERFACE
1. Centronics interface
(1) Connector (CN2)
Connector part number : FCN-605Q030-G/M (Fujitsu Components) or equivalent
Mating connector part number : FCN-607B030-G/B (Fujitsu Components) or equivalent
No.1
No.2
No.30
PRDT0~7
PRSTB
BUSY
ACKNLG
t1 t3
t2
t4
t5
Data set time
PRSTB pulse width
Data hold time
PRSTB to BUSY= “H”
ACKNLG pulse time
:t1≥0.5 µsec
:t2≥0.5 µsec
:t3≥0.5 µsec
:t4≤0.5 µsec
:t5≈ 5.0 µsec
8
FTP-628MCL Series
NOT FOR NEW
DESIGN
2. RS-232C
(1) Connector (CN7)
Connector part number : B10B-PH-K-S (J.S.T.) or equivalent
Mating connector part number : PHR-10 (J.S.T.) or equivalent
(2) Connector pin assignment
Notes:
• Symbol “——” means a negative logic signal.
• “I” or “O” means a signal direction from the interface board side.
(5) Printer status signals
sutatsrorrE1FNIR2FNIR3FNIR
.1tuorepaPwoLhgiHwoL
.2dneraenrepaPhgiHhgiHwoL
.3pudaeHhgiHwoLwoL
.4ytilamronbaerutarepmetdaeHhgiHwoLhgiH
.5ytilamronbaegatlovdaeHwoLhgiHhgiH
.6ytilamronbaerawdraHhgiHhgiHhgiH
.7ytilamronbanoitcetedkraMwoLwoLwoL
.8lamroNwoLwoLhgiH
.oNlangiSO/I.oNstnetnoC.oNlangiSO/I.oNstnetnoC
1GF- dnuorgemarF2DRI atadevieceR
3DTO atadnoissimsnarT4RTDO ydaerlanimretataD
5DNG- dnuorglangiS6RSDI ydaertesataD
7NITCLSI tcelesretnirP8MRPNIIteseR
9FTAI tseuqerdeefrepaP01DWPI noitallecnacnwodrewoP
langis
9
FTP-628MCL Series
NOT FOR NEW
DESIGN
■CONNECTOR PIN ASSIGNMENT
1. Connector for power supply (CN1)
Part number : B6P-VH (J.S.T) or equivalent (board side)
Mating Connector : VHR-6N
2. Connector for printer mechanism connection (CN3)
Part number : 52030-3010 (made by Molex) or equivalent (board side)
.oNlangiSO/I.oNstnetnoC.oNlangiSO/I.oNstnetnoC
15V+- cigolrofylppusrewoP2DNG-dnuorG
3DNG-dnuorG4DNG-dnuorG
5HV+- rotomdaehrofylppusrewoP6HV+- rotomdaehrofylppusrewoP
No. Signal I/O Contents No. Signal I/O Contents
1 PHK — Photo interrupter (cathode) 2 VSEN O
Power supply for paper senor
3 PHE I Photo interrupter (emitter) 4VH O
Head driving power supply
5VH O
Head driving power supply
6 GNC —
Ground for head
7 GND —
Ground for head
8 DIN O
Data input
9 LAT O Data latch 10 CLK O
Clock
11 STB6 O Enable 6 12 STB5 O
Enable 5
13 STB4 O Enable 4 14 VDD O
Logic Power supply
15 STB3 O Enable 3 16 STB 2 O
Enable 2
17 STB1 O Enable 1 18 TH I
Thermistor
19 TH I Thermistor 20 GND —
Ground for head
21 GND —
Ground for head
22 VH O
Head driving power supply
23 VH O
Head driving power supply
24 N.C. —
Open terminal
25 SW1 O Head open switch* 26 SW2 I Head open switch*
27 MT/B O Stepping motor coil 28 MT/B O Stepping motor coil
excitation signal B excitation signal B
29 MT/A O Stepping motor coil 30 MT/A O Stepping motor coil
excitation signal A excitation signal A
* on MCL003 and MCL004 models
10
FTP-628MCL Series
NOT FOR NEW
DESIGN
■OPTIONS
emaNrebmuNtraP)mm(htgneL
elbaCecafretnI
dnadraobneewteb(
)tnempiuqe
)2NC(scinortneCroF102Y144-PTF005
)7NC(C232SRroF103Y826-PTF005
)1NC(elbacylppusrewoP104Y226-PTF003
deriuqerfi)8NC(rosnesrepapdneraeN
11
FTP-628MCL Series
NOT FOR NEW
DESIGN
Command Contents
HT Moves print position to the next tab.
LF Line feed.
FF Feeds forms (new page).
DC 2 Power down.
ECS RS Sets reverse printing.
ESC US Resets reverse printing.
ESC ! + n Sets print mode.
ESC %+n Download character set specification//cancellation.
ESC &+y+c1+c2+x+d1~dNDownload character definition.
ESC *+m+n1+n2+d1~dNSets bit image mode.
ESC ?+n External registration character deletion.
ESC 2 Sets 1/6 inch line feed length.
ESC 3+n Sets the line feed length.
ESC @ Printer initialization.
ESC A+n Sets the space between the line.
ESC C+n Sets the page length by character line.
ESC D+d1~dN+NUL Sets the tab position.
ESC J+n Feeds paper in forward direction and prints.
ESC K+n Reverse paper feed.
ESC R+n Selects international character.
ESC c+1+n Sets internal processing (including auto paper loading).
ESC d+n Printing and n-line feeding.
ESC e+n Prints and reverse feeds n-lines.
ECS s+n Sets printing speed.
ECS t+n Character code table selection.
ESC {+n Sets/resets upside down printing.
FS !+n Kanji printing mode collective specification.
FS & Kanji printing mode specification.
FS . Kanji printing mode cancellation.
FS 9+n Sets the detection functions.
■COMMANDS
12
FTP-628MCL Series
NOT FOR NEW
DESIGN
Command Contents
FS W+n Kanji double height and width mode specification/cancellation.
GS < Line feeds to the next mark.
GS A+m+n Sets the line feed length after mark detection.
GS E+n Sets print quality.
GS V+n+m Paper cutting (for pending cutter models only).
GS e+n+m Sets bar code width.
GS h+n Sets bar code height.
GS k+m+n+d1~dNSelects bar code type and prints.
GS w+n Sets bar code width magnification.
FS *+m+n1+n2+d1~dNHigh speed collective image printing specified.
GS &+m+x+y1+y2+d1~dNRegistration of image data.
GS '+m+n Prints registered image data.
FS E+n Correction of impressed energy.
ESC V+n Right Rotation 90° specification / cancellation.
GS a+n Sets and cancels status transmission. (Serial Mode)
FS r+n Parameter transmission. (Serial Mode)
ESC EM+n Setting the amount of the feeding at automatic paper load.
ECS X+n+m Setting the turning time of the motor excitation.
ESC DEL+n Deletes recorded contents in flash memory.
FS C+n Kanji code system selection.
Commands continued
© 2003 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 04/03/2003
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: promothq@ft.ed.fujitsu.com
Web: www.fcl.fujitsu.com
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: marcom@fcai.fujitsu.com
Web: www.fcai.fujitsu.com
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: info@fceu.fujitsu.com
Web: www.fceu.fujitsu.com
Asia Pacific
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (65) 6273-3021
Email: fcal@fcal.fujitsu.com
www.fcal.fujitsu.com
Fujitsu Components
International
Headquarter
Offices
