Fujitsu P128 139 FTP 624DSL113
User Manual: Fujitsu FTP-624DSL113 Datasheet - Fujitsu United States
Open the PDF directly: View PDF .
Page Count: 7
Download | |
Open PDF In Browser | View PDF |
INTERFACE BOARDS FOR FTP-604 Series FTP-624DSL113 ■ INTERFACE 1. Centronics standard (1) Connector (CN3) Connector part number : FCN-605Q030-G/M (Fujitsu Components) Mating connector part number : FCN-607B030-G/B (Fujitsu Components) or equivalent (2) Connector pin assignment No. Signal I/O Contents No. Signal I/O Contents 1 PRSTB I Data strobe 2 PRSTB-RET — Connected to logic GND 3 PRDT0 I Data 0 4 PRDT0-RET — Connected to logic GND 5 PRDT1 I Data 1 6 PRDT1-RET — Connected to logic GND 7 PRDT2 I Data 2 8 PRDT2-RET — Connected to logic GND 9 PRDT3 I Data 3 10 PRDT3-RET — Connected to logic GND 11 PRDT4 I Data 4 12 PRDT4-RET — Connected to logic GND 13 PRDT5 I Data 5 14 PRDT5-RET — Connected to logic GND 15 PRDT6 I Data 6 16 PRDT6-RET — Connected to logic GND 17 PRDT7 I Data 7 18 PRDT7-RET — Connected to logic GND 19 ACKNLG O Data input acknowledge 20 ACKNLG-RET — Connected to logic GND 21 BUSY O Busy 22 BUSY-RET — Connected to logic GND 23 RINF2 O Printer status 2 24 INPRM-RET — Connected to logic GND 25 SLCTIN I Printer select 26 INPRM I Reset 27 RINF1 O Printer status 1 28 RINF3 O Printer status 3 29 ATF I Paper feed request 30 GND — Logic GND Notes: • Symbol “——” means a negative logic signal. • “–RET” signal is a return signal of the twisted pair cable. • “I” or “O” means a signal direction from the interface board side. (3) Connector pin number (4) Data input signal timing FCN-605Q030-G/M (Fujitsu Components) PRDT0~7 t1 No.1 t3 PRSTB t2 BUSY t4 No.30 No.2 ACKNLG t5 Data set time PRSTB pulse width Data hold time PRSTB to BUSY= “H” ACKNLG pulse time 1 :t1≥0.5 µsec :t2≥0.5 µsec :t3≥0.5 µsec :t4≤0.5 µsec :t5≈ 5.0 µsec FTP-624DSL113 (4) Printer status signals Error status RINF1 RINF2 RINF3 1. Paper out Low High Low 2. Paper near end High High Low 3. Head up High Low Low 4. Head temperature abnormality High Low High 5. Head voltage abnormality Low High High 6. Hardware abnormality High High High 7. Mark detection abnormality Low Low Low 8. Normal Low Low High 2. RS-232C (1) Connector (CN9) Connector part number : B9B-PH-K-S (J.S.T.) Mating connector part number : PHR-9 (J.S.T.) or equivalent (2) Connector pin assignment No. Signal I/O Contents No. No. Signal I/O Contents No. 1 FG - Frame ground 2 RD I Receive data 3 TD O Transmission data 4 DTR O Data terminal ready 5 GND - Signal ground 6 DSR I Data set ready 7 SLCTIN I Printer select 8 INPRM I Reset 9 AFT I Paper feed request Notes: • Symbol “——” means a negative logic signal. • “I” or “O” means a signal direction from the interface board side. (3) Connector pin numbers CN9 CN3 9 1 2 FTP-624DSL113 ■ CONNECTOR PIN ASSIGNMENT 1. Connector for logic power supply (CN1) Part number Mating connector No. 1 Signal : B2B-VH (J.S.T) : VHP-2 (J.S.T) or equivalent I/O Contents +5V Power for logic IC No. 2 Signal GND(+5V) I/O — Contents Logic GND 2. Connector for thermal head and motor power supply (CN2) Part number Mating connector No. Signal : B6B-XH-A-WHITE (J.S.T) : XHP-6 (J.S.T) or equivalent I/O 1 5VH 3 5VH 5 GND(5VH) — — Contents No. Signal I/O Contents Power for thermal head/motor 2 5VH Power for thermal head/motor Power for thermal head/motor 4 GND(5VH) — Thermal head/motor GND Thermal head/motor GND 6 GND(5VH) — Thermal head/motor GND 3. Connector for stepping motor drive (CN4) Part number No. Signal : B4B-PH-K-S (J.S.T) I/O Contents No. Signal I/O Contents 1 MT/B O Stepping motor coil excitation 2 MT/B O Stepping motor coil excitation 3 MT/A O Stepping motor coil excitation 4 MT/A O Stepping motor coil excitation 4. Connector for sensor (CN5) Part number No. Signal 1 +5V 3 5 : B5B-PH-K-S (J.S.T) I/O Contents — No. Signal I/O Power for detector 2 PES I GND (+5V) — Logic GND 4 +5V — HUP Head-up detect signal I Contents Paper out detect signal Power for detector 5. Connector for cutter drive (CN6) Part number : B6B-EH (J.S.T) No. Signal I/O Contents No. Signal I/O Contents 1 SWI I Power supply for cutter home position detector 2 GND - Logic ground 3 M+ O Cutter motor drive (+) 4 M+ O Cutter motor drive (+) 5 M- O Cutter motor drive (-) 6 M- O Cutter motor drive (-) 3 FTP-624DSL113 6. Connector for FTP-624 thermal head drive (CN8) Part number Mating connector No. Signal I/O : B16B-PH-K-S (J.S.T) : PHR-16 (J.S.T) or equivalent Contents No. Signal I/O Contents 1 5VH O Power for thermal head 2 GND — Logic/head GND 3 GND — Logic/head GND 4 ENB0 O Print enable 0 5 ENB1 O Print enable 1 6 ENB2 O Print enable 2 7 ENB3 O Print enable 3 8 TMP I Temperature detection signal 9 ENB4 O Print enable 4 10 LAT O Print data latch signal 11 ENB5 O Print enable 5 12 5V O Power for logic 13 HCLK O Data transmission clock 14 HD O Print data output signal 15 GND — Logic/head GND 16 5VH O Power for head Notes: Symbol “——” means a negative logic signal. “I” or “O” means a signal direction from the interface board side. 7. Connector for paper near end detection (CN10) Part number Mating connector No. Signal I/O : B2B-PH-K-S (J.S.T) : PHR-2 (J.S.T.) Contents 1 +5V — Power supply for detector 2 NES I Paper near end detection CN11: Not used 4 FTP-624DSL113 ■ COMMANDS Command Contents HT Moves print position to the next tab. LF Line feed. FF Feeds forms (new page). DC 2 Power down. ECS RS Sets reverse printing. ESC US Resets reverse printing. ESC ! + n Sets print mode. ESC %+n Download character set specification//cancellation. ESC &+y+c1+c2+x+d1~dN Download character definition. ESC *+m+n1+n2+d1~dN Sets bit image mode. ESC ?+n External registration character deletion. ESC 2 Sets 1/6 inch line feed length. ESC 3+n Sets the line feed length. ESC @ Printer initialization. ESC A+n Sets the space between the line. ESC C+n Sets the page length by character line. ESC D+d1~dN+NUL Sets the tab position. ESC J+n Feeds paper in forward direction and prints. ESC K+n Reverse paper feed. ESC R+n Selects international character. ESC c+1+n Sets internal processing. ESC d+n Printing and n-line feeding. ESC e+n Prints and reverse feeds n-lines. ECS s+n Sets printing speed. ECS t+n Character code table selection. ESC {+n Sets/resets upside down printing. FS !+n Kanji printing mode collective specification. FS & Kanji printing mode specification. FS . Kanji printing mode cancellation. FS 9+n Sets the detection functions. 5 FTP-624DSL113 Commands continued Command Contents FS C+n Kanji code system selection. FS W+n Kanji double height and width mode specification/cancellation. GS < Line feeds to the next mark. GS A+m+n Sets the line feed length after mark detection. GS E+n Sets print quality. GS V+n+m Paper cutting. GS e+n+m Sets bar code width. GS h+n Sets bar code height. GS k+m+n+d1~dN Selects bar code type and prints. GS w+n Sets bar code width magnification. FS *+m+n1+n2+d1~dN High speed collective image printing specified. GS &+m+x+y1+y2+d1~dN Registration of image data. GS '+m+n Prints registered image data. FS E+n Correction of impressed energy. ESC V+n Right Rotation 90° specification / cancellation. GS a+n Sets and cancels status transmission. (Serial Mode) FS r+n Parameter transmission. (Serial Mode) ESC EM+n Setting the amount of the feeding at automatic paper feed. ESC X+n+m Setting the turning time of the motor excitation. ■ OPTIONS 1. Cable (With FTP-624MCL303/304) Name Part Number Cable length Thermal head connection cable (CN8) 624MCL FTP-624Y001 170mm (6.7 in.) Interface cable (CN3) Centronics FTP-441Y201 500mm(19.7 in.) Interface cable (CN9) Serial FTP-624Y301 300mm (11.8 in.) Power cable (CN1) (CN2) Logic FTP-624Y401 300mm (11.8 in.) Head, motor FTP-624Y601 300mm (11.8 in.) 6 FTP-624DSL113 Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fceu.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: marcom@fcai.fujitsu.com Web: www.fcai.fujitsu.com Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #04-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com www.fcal.fujitsu.com © 2002 Fujitsu Components America, Inc. All company and product names are trademarks or registered trademarks of their respective owners. Rev. 06/2002 7
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.1 Linearized : No Page Count : 7 Create Date : 2005:04:20 17:33:09 Producer : Acrobat Distiller 3.0 for Power Macintosh Subject : p128-139 Creator : Adobe PageMaker 6.5 Title : p128-139 Author :EXIF Metadata provided by EXIF.tools