Fujitsu P128 139 FTP 624DSL113

User Manual: Fujitsu FTP-624DSL113 Datasheet - Fujitsu United States

Open the PDF directly: View PDF PDF.
Page Count: 7

INTERFACE BOARDS FOR FTP-604 Series
FTP-624DSL113
No. Signal I/O Contents No. Signal I/O Contents
1 PRSTB I Data strobe 2 PRSTB-RET
Connected to logic GND
3 PRDT0 I Data 0 4 PRDT0-RET
Connected to logic GND
5 PRDT1 I Data 1 6 PRDT1-RET
Connected to logic GND
7 PRDT2 I Data 2 8 PRDT2-RET
Connected to logic GND
9 PRDT3 I Data 3 10 PRDT3-RET
Connected to logic GND
11 PRDT4 I Data 4 12 PRDT4-RET
Connected to logic GND
13 PRDT5 I Data 5 14 PRDT5-RET
Connected to logic GND
15 PRDT6 I Data 6 16 PRDT6-RET
Connected to logic GND
17 PRDT7 I Data 7 18 PRDT7-RET
Connected to logic GND
19 ACKNLG O Data input acknowledge 20 ACKNLG-RET
Connected to logic GND
21 BUSY O Busy 22 BUSY-RET
Connected to logic GND
23 RINF2 O Printer status 2 24 INPRM-RET
Connected to logic GND
25 SLCTIN I Printer select 26 INPRM I Reset
27 RINF1 O Printer status 1 28 RINF3 O Printer status 3
29 ATF I Paper feed request 30 GND Logic GND
Notes: • Symbol “——” means a negative logic signal.
• “–RET” signal is a return signal of the twisted pair cable.
• “I” or “O” means a signal direction from the interface board side.
(2) Connector pin assignment
INTERFACE
(3) Connector pin number (4) Data input signal timing
FCN-605Q030-G/M (Fujitsu Components)
No.1
No.2No.30
PRDT0~7
PRSTB
BUSY
ACKNLG
t1 t3
t2
t4
t5
Data set time
PRSTB pulse width
Data hold time
PRSTB to BUSY= “H”
ACKNLG pulse time
:t10.5 µsec
:t20.5 µsec
:t30.5 µsec
:t40.5 µsec
:t5 5.0 µsec
1. Centronics standard
(1) Connector (CN3)
Connector part number : FCN-605Q030-G/M (Fujitsu Components)
Mating connector part number : FCN-607B030-G/B (Fujitsu Components) or equivalent
1
2
FTP-624DSL113
2. RS-232C
(1) Connector (CN9)
Connector part number : B9B-PH-K-S (J.S.T.)
Mating connector part number : PHR-9 (J.S.T.) or equivalent
(2) Connector pin assignment
Notes:
• Symbol “——” means a negative logic signal.
• “I” or “O” means a signal direction from the interface board side.
(3) Connector pin numbers
91
CN9
CN3
(4) Printer status signals
.oNlangiSO/I.oNstnetnoC.oNlangiSO/I.oNstnetnoC
1GF- dnuorgemarF2DRI atadevieceR
3DTO atadnoissimsnarT4RTDO ydaerlanimretataD
5DNG- dnuorglangiS6RSDI ydaertesataD
7NITCLSI tcelesretnirP8MRPNIIteseR
9TFAI tseuqerdeefrepaP
sutatsrorrE1FNIR2FNIR3FNIR
.1tuorepaPwoLhgiHwoL
.2dneraenrepaPhgiHhgiHwoL
.3pudaeHhgiHwoLwoL
.4ytilamronbaerutarepmetdaeHhgiHwoLhgiH
.5ytilamronbaegatlovdaeHwoLhgiHhgiH
.6ytilamronbaerawdraHhgiHhgiHhgiH
.7ytilamronbanoitcetedkraMwoLwoLwoL
.8lamroNwoLwoLhgiH
3
FTP-624DSL113
No. Signal I/O Contents No. Signal I/O Contents
1 MT/B O Stepping motor coil excitation 2 MT/B O Stepping motor coil excitation
3 MT/A O Stepping motor coil excitation 4 MT/A O Stepping motor coil excitation
3. Connector for stepping motor drive (CN4)
Part number : B4B-PH-K-S (J.S.T)
No. Signal I/O Contents No. Signal I/O Contents
1 5VH Power for thermal head/motor 2 5VH Power for thermal head/motor
3 5VH Power for thermal head/motor 4 GND(5VH) Thermal head/motor GND
5 GND(5VH) Thermal head/motor GND 6 GND(5VH) Thermal head/motor GND
No. Signal I/O Contents No. Signal I/O Contents
1 +5V Power for logic IC 2 GND(+5V) Logic GND
CONNECTOR PIN ASSIGNMENT
1. Connector for logic power supply (CN1)
Part number : B2B-VH (J.S.T)
Mating connector : VHP-2 (J.S.T) or equivalent
2. Connector for thermal head and motor power supply (CN2)
Part number : B6B-XH-A-WHITE (J.S.T)
Mating connector : XHP-6 (J.S.T) or equivalent
4. Connector for sensor (CN5)
Part number : B5B-PH-K-S (J.S.T)
No. Signal I/O Contents No. Signal I/O Contents
1 +5V Power for detector 2 PES I Paper out detect signal
3 GND (+5V) Logic GND 4 +5V Power for detector
5 HUP I Head-up detect signal
5. Connector for cutter drive (CN6)
Part number : B6B-EH (J.S.T)
.oNlangiSO/IstnetnoC.oNlangiSO/IstnetnoC
1IWSI rettucrofylppusrewoP rotcetednoitisopemoh 2DNG- dnuorgcigoL
3+MO )+(evirdrotomrettuC4+MO )+(evirdrotomrettuC
5-MO )-(evirdrotomrettuC6-MO )-(evirdrotomrettuC
4
FTP-624DSL113
CN11: Not used
6. Connector for FTP-624 thermal head drive (CN8)
Part number : B16B-PH-K-S (J.S.T)
Mating connector : PHR-16 (J.S.T) or equivalent
Notes: Symbol “——” means a negative logic signal.
“I” or “O” means a signal direction from the interface board side.
No. Signal I/O Contents No. Signal I/O Contents
1 5VH O Power for thermal head 2 GND Logic/head GND
3 GND Logic/head GND 4 ENB0 O Print enable 0
5 ENB1 O Print enable 1 6 ENB2 O Print enable 2
7 ENB3 O Print enable 3 8 TMP I Temperature detection signal
9 ENB4 O Print enable 4 10 LAT O Print data latch signal
11 ENB5 O Print enable 5 12 5V O Power for logic
13 HCLK O Data transmission clock 14 HD O Print data output signal
15 GND Logic/head GND 16 5VH O Power for head
7. Connector for paper near end detection (CN10)
Part number : B2B-PH-K-S (J.S.T)
Mating connector : PHR-2 (J.S.T.)
No. Signal I/O Contents
1 +5V Power supply for detector
2 NES I Paper near end detection
5
FTP-624DSL113
Command Contents
HT Moves print position to the next tab.
LF Line feed.
FF Feeds forms (new page).
DC 2 Power down.
ECS RS Sets reverse printing.
ESC US Resets reverse printing.
ESC ! + n Sets print mode.
ESC %+n Download character set specification//cancellation.
ESC &+y+c1+c2+x+d1~dNDownload character definition.
ESC *+m+n1+n2+d1~dNSets bit image mode.
ESC ?+n External registration character deletion.
ESC 2 Sets 1/6 inch line feed length.
ESC 3+n Sets the line feed length.
ESC @ Printer initialization.
ESC A+n Sets the space between the line.
ESC C+n Sets the page length by character line.
ESC D+d1~dN+NUL Sets the tab position.
ESC J+n Feeds paper in forward direction and prints.
ESC K+n Reverse paper feed.
ESC R+n Selects international character.
ESC c+1+n Sets internal processing.
ESC d+n Printing and n-line feeding.
ESC e+n Prints and reverse feeds n-lines.
ECS s+n Sets printing speed.
ECS t+n Character code table selection.
ESC {+n Sets/resets upside down printing.
FS !+n Kanji printing mode collective specification.
FS & Kanji printing mode specification.
FS . Kanji printing mode cancellation.
FS 9+n Sets the detection functions.
COMMANDS
6
FTP-624DSL113
Command Contents
FS W+n Kanji double height and width mode specification/cancellation.
GS < Line feeds to the next mark.
GS A+m+n Sets the line feed length after mark detection.
GS E+n Sets print quality.
GS V+n+m Paper cutting.
GS e+n+m Sets bar code width.
GS h+n Sets bar code height.
GS k+m+n+d1~dNSelects bar code type and prints.
GS w+n Sets bar code width magnification.
FS *+m+n1+n2+d1~dNHigh speed collective image printing specified.
GS &+m+x+y1+y2+d1~dNRegistration of image data.
GS '+m+n Prints registered image data.
FS E+n Correction of impressed energy.
ESC V+n Right Rotation 90° specification / cancellation.
GS a+n Sets and cancels status transmission. (Serial Mode)
FS r+n Parameter transmission. (Serial Mode)
ESC EM+n Setting the amount of the feeding at automatic paper feed.
ESC X+n+m Setting the turning time of the motor excitation.
FS C+n Kanji code system selection.
Commands continued
OPTIONS
1. Cable (With FTP-624MCL303/304)
emaNrebmuNtraPhtgnelelbaC
)8NC(elbacnoitcennocdaehlamrehTLCM426100Y426-PTF).ni7.6(mm071
)3NC(elbacecafretnIscinortneC102Y144-PTF).ni7.91(mm005
)9NC(elbacecafretnIlaireS103Y426-PTF).ni8.11(mm003
)1NC(elbacrewoP
)2NC(
cigoL104Y426-PTF).ni8.11(mm003
rotom,daeH106Y426-PTF).ni8.11(mm003
7
FTP-624DSL113
© 2002 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 06/2002
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: promothq@ft.ed.fujitsu.com
Web: www.fcl.fujitsu.com
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: marcom@fcai.fujitsu.com
Web: www.fcai.fujitsu.com
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: info@fceu.fujitsu.com
Web: www.fceu.fujitsu.com
Asia Pacific
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (65) 6273-3021
Email: fcal@fcal.fujitsu.com
www.fcal.fujitsu.com
Fujitsu Components
International
Headquarter
Offices

Navigation menu