Fujitsu FTR F3 (10A 1 Form C) 10a Cc
User Manual: Fujitsu FTR-F3 (10A 1 form C) Datasheet - Fujitsu United States
Open the PDF directly: View PDF 
.
Page Count: 5
1
FTR-K1 SERIES
n FEATURES
l Low prole and space saving
- Height: 15mm
- Mounting space: 164mm2
l High insulation
- Insulation distance: 7mm between coil and contacts
- Dielectric strength: 4,000VAC between coil and contacts
- Surge strength: 10,000V between coil and contacts
l Plastic materials
- UL94 ame class V-0
l Cadmium free relay
l Lead free relay
l Plastic sealed type
l RoHS compliant
Please see page 4 for more information
POWER RELAY
1 POLE - 10A changeover relay
FTR-F3 Series
n PARTNUMBER INFORMATION
FTR-F3 C A 012 E - HC
[Example] (a) (b) (c) (d) (e) (f)
Preliminary New relay, production not started,
engineering samples available
Actual marking does not carry the type name : "FTR"
E.g.: Ordering code: FTR-F3CA012E Actual marking: F3CA012E
(a) Relay type FTR-F3 : FTR-F3-Series
(b) Contact conguration C : 1 form C
(c) Coil type (power) A : 360mW
(d) Coil rated voltage 012 : 5.....24 VDC
Coil rating table at page 3
(e) Contact material E : Ag Alloy
(f) Enclosure HC
HK
: Flux proof type
: Sealed type
2
FTR-K1 SERIES
n SPECIFICATION
* Minimum switching loads mentioned above are reference values. Please perform the conrmation test with actual load before production since
reference values may vary according to switching frequencies, environmental conditions and expected reliability levels.
Item FTR-F3
FTR-F3CA( )E-HC FTR-F3CA( )E-HK
Contact Data Conguration 1 form C (SPDT)
Construction Single
Material Ag Alloy
Resistance (initial) Max. 100mOhm at 1A, 6VDC
Contact rating (resistive) 10A, 250VAC
Max. carrying current 10A
Max. switching voltage 277VAC
Max. switching power 2,500VAC
Min. switching load * 100 mA, 5VDC
Life Mechanical Min. 20 x 106 operations
Electrical (at rated load) Make: 50 x 103 operations
Break: 10 x 103 operations
Make: 10 x 103 operations
Break: 6 x 103 operations
Coil Data Rated power (20 °C) 360mW
Operating temperature range -40 °C to +85 °C (no frost)
Timing Data Operate (at nominal voltage) Max. 10ms (without bounce)
Release (at nominal voltage) Max. 10ms (without bounce)
Insulation Resistance (initial) Min. 1,000MOhm at 500VDC
Dielectric strength Open contacts 750VAC (50/60Hz) 1min
Contacts to coil 4,000VAC (50/60Hz) 1min
Surge strength Contacts to coil 10,000V / 1.2 x 50µs standard wave
Other Vibration resistance Misoperation 10 to 55Hz double amplitude 1.5mm
Endurance 10 to 55Hz double amplitude 1.5mm
Shock Misoperation Min. 100m/s2 (11±1ms)
Endurance Min. 1,000m/s2 (6±1ms)
Weight Approximately 6g
Enclosure Flux proof Plastic sealed
FTR-F3 SERIES
Preliminary
3
FTR-K1 SERIES
n COIL RATING
Coil
Code
Rated Coil
Voltage
(VDC)
Coil Resistance
+/- 10%
(Ohm)
Must Operate
Voltage
(VDC) *
Must Release
Voltage
(VDC) *
005 5 69 3.75 0.5
006 6 100 4.5 0.6
009 9225 6.75 0.9
012 12 400 91.2
018 18 900 13.5 1.8
024 24 1,600 18 2.4
Note: All values in the tables are valid for 20°C and zero contact current.
* Specied operate values are valid for pulse wave voltage.
FTR-F3 SERIES
Type Contact rating
FTR-F3CA( )E-HC FTR-F3CA( )E-HK
UL Flammability: UL 94-V0 (plastics)
10A, 250VAC (resistive) 10A, 250VAC (resistive)
CSA
VDE
n SAFETY STANDARDS (Plan)
Preliminary
n DIMENSIONS
Unit: mm
l Schematics
(BOTTOM VIEW)
l PC board mounting
hole layout
(BOTTOM VIEW)
l Dimensions
4
FTR-K1 SERIES
FTR-F3 SERIES
1. General Information
l All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including
amendments.
l Cadmium as used in electrical contacts is exempted from the RoHS directives.
As per Annex III of directive 2011/65/EU.
l All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at:
http://www.fujitsu.com/downloads/MICRO/fcai/relays/lead-free-letter.pdf
l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified.
This material has been verified to be compatible with PbSn assembly process.
2. Recommended Lead Free Solder Condition
l Recommended solder Sn-3.0Ag-0.5Cu.
RoHS Compliance and Lead Free Information
3. Moisture Sensitivity
l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated.
4. Tin Whiskers
l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length
whisker was found by our in house test.
We highly recommend that you conrm your actual solder conditions
Preliminary
Flow Solder Condition:
Pre-heating: maximum 120˚C
within 90 sec.
Soldering: dip within 5 sec. at
255˚C ± 5˚C solder bath
Relay must be cooled by air immediately
after soldering
Solder by Soldering Iron:
Soldering Iron 30-60W
Temperature: maximum 350-360˚C
Duration: maximum 3 sec.
5
FTR-K1 SERIES
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: promothq@ft.ed.fujitsu.com
Web: www.fcl.fujitsu.com
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: components@us.fujitsu.com
Web: http://us.fujitsu.com/components
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: info@fceu.fujitsu.com
Web: emea.fujitsu.com/components/
Asia Pacic
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#01-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (65) 6273-3021
Email: fcal@fcal.fujitsu.com
Web: http://www.fujitsu.com/sg/services/micro/components/
Fujitsu Components International Headquarter Ofces
©2014 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners.
The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general
information purposes.
The use of the contents, data and information provided in this datasheet is at the users’ own risk.
Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive,
complete and up to date.
Fujitsu Components Europe B.V. and afliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its
employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related
graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof.
Nor do Fujitsu Components Europe B.V. and afliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability
for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or tness for particular use,
with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness,
usefulness, availability and completeness thereof. Rev. June 26, 2014
FTR-F3 SERIES
Preliminary
