Fujitsu FTR F3 (5A 1 Form C) Cc
User Manual: Fujitsu FTR-F3 (5A 1 form C) Datasheet - Fujitsu United States
Open the PDF directly: View PDF 
.
Page Count: 7
| Download | |
| Open PDF In Browser | View PDF |
POWER RELAY 1 POLE - 5A Change Over Relay FTR-F3 Series ■■ FEATURES • High density mounting • • • • • Height: 15mm Mounting space: 164mm2 High insulation Insulation distance: 7mm between coil and contacts (conforms to IEC 60065) Dielectric strength: 4KV Surge strength: 10KV Cadmium free contact for eco-program Safety standards UL, CSA, VDE Plastic sealed relay, RTIII RoHS compliant Please see page 6 for more information ■■ Part Numbers [Example] FTR-F3 C A 012 E (a) (b) (c) (d) (e) (a) Relay type FTR-F3 : FTR-F3 series (b) Contact configuration C : 1 form C (c) Coil type (power) A : 360mW (d) Coil rated voltage (e) Contact material 012 : 5..... 24VDC Coil rating table at page 3 E : AgNi Actual marking does not carry the type name: "FTR" E.g.: Ordering code: FTR-F3CA012E Actual marking: F3CA012E 1 FTR-F3 Series ■■ Specifications Item FTR-F3 Contact Configuration data Construction 1 form C Single Material AgNi Resistance Max. 100mOhm Contact rating 5A, 250VAC, 30VDC Max. carrying current 277VAC, 30VDC Max. switching power 1,250VA, 150W *1 Rated power (20 C) o Operating temperature range Initial at 1A, 6VDC Resistive 5A Max. switching voltage Min. switching load Coil Remarks / conditions 10 mA, 5VDC 360mW -40ºC ~ +70ºC (at rated voltage) No frost Timing data Operate Max. 10ms without bounce Release Max. 10ms without bounce Life Mechanical Insulation Min. 2 x 10⁶ operations Electrical (resistive) Min. 100 x 103 operations (3A, 250VAC/30VDC) Min. 50 x 10³ operations (5A, 250VAC/30VDC) Insulation resistance Min. 1000MΩ at 500VDC Dielectric strength Open contacts 750VAC (50/60Hz), 1 minute Coil contact 4000VAC (50/60Hz), 1 minute Surge strength Coil to contacts Other 7mm Creepage 7mm Voltage 250V Pollution 2 Material group III Vibration resis- Misoperation tance Endurance Shock resistance Sealing : 10Hz ~ 55Hz ~ 10Hz single amplitude 0.75mm 10Hz ~ 55Hz ~ 10Hz single amplitude 0.75mm Misoperation ≥1us Min. 100m/s² (11 ± 1ms) Endurance Min. 1,000m/s² (6 ± 1ms) Dimensions / weight *1 10,000V / 1.2 x 50μs standard wave Clearance EN61810-1, VDE0435 At rated load 7.0 x 23.4 x 15.0 mm / approx. 6g Plastic sealed RTIII Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions 2 FTR-F3 Series ■■ Coil Data Coil code Rated Coil Voltage Coil Resistance +/-10% Must Operate Voltage* Must Release Voltage* (VDC) (Ω) (VDC) (VDC) 005 5 69 3.75 0.5 006 6 100 4.5 0.6 009 9 225 6.75 0.9 012 12 400 9 1.2 018 18 900 13.5 1.8 024 24 1,600 18 2.4 Rated Power (mW) 360 Note: All values in the table are valid at 20oC and zero contact current, unless otherwise specified. * : Specified operated values are valid for pulse wave voltage. Note: Please use at rated coil voltage. Please refer to characteristic data and set up adequate voltage in case of use at over voltage. ■■ Safety Standards Type Compliance Contact rating UL UL 508 Flammability: UL 94-V-0 (plastics) File No. E63614 5A, 30 VDC / 250VAC (resistive) 3A, 30 VDC / 250 VAC (resistive) CSA C22.2 No. 14 File No. LR 40304 VDE IEC/EN61810-1 EN60065 clause 14.6.1 5A, 250 VAC, cosφ=1 5A, 30 VDC L/R=0ms 3A, 250 VAC, cosφ=1 3A, 30 VDC L/R=0ms CQC GB15092.1 / GB/T21811.1 17002164382, 04001010925 5A 250VAC / 30VDC 3 FTR-F3 Series ■■ Characteristic Data (Reference) * Characteristic data is not guaranteed value but measured values of samples from production line. Operating Range Coil Temperature Rise FTR-F3C Nominal voltage multiplying factor 80 Coil Temperature Rise(°C) FTR-F3C 2.0 70 60 50 5A 40 30 0A 20 1.8 0A 1.6 5A 1.4 1.2 1.0 ltage te vo era st op Mu 0.8 (hot coil) il) ool co age (c te volt era ust op M 10 5 Switching Current (A) 90 0 0.1 0.2 0.3 0.4 0 0.5 10 20 30 40 50 60 70 80 DC resistive 1 AC resistive 0.5 0.1 10 90 100 110 20 50 Life Curve 500 1000 100 100 FTR-F3CA012E n=100 FTR-F3CA012E n=100 N.O.contact 125VAC resistive 250VAC/30VDC resistive 200 Distribution of Contact Resistance (N.C.) Distribution of Contact Resistance (N.O.) 1000 100 Contact Voltage (V) Ambient Temperature(° C) Coil Power (W) 500 2 0.2 0.6 0 80 N.C.contact 80 200 50 250VAC cos=φ0.4 20 10 60 Distribution (%) 100 Distribution (%) Service Life (X103 operations) Maximum Switching Power 10 2.2 100 40 5 60 40 20 20 2 0 0 1 2 3 4 5 0 6 Contact Current (A) 0 40 20 10 20 30 40 60 70 0 20 80 90 Nominal Voltage Multiplying Factor (%) 100 60 80 100 Distribution of Release Time 100 FTR-F3CA012E n=100 Operate time FTR-F3CA012E n=100 個 Release time 80 60 40 0 40 Contact Resistance (mΩ) 60 40 20 20 0 0 100 Distribution (%) Distribution (%) Distribution (%) 80 80 60 0 60 Distribution of Operation Time 100 FTR-F3CA012E n=100 Operate voltage Release voltage 80 40 Contact Resistance (mΩ) Distribution of Operation & Release Voltage 100 20 0.0 2.0 4.0 6.0 Time (ms) 8.0 10.0 0 0.0 2.0 4.0 6.0 8.0 10.0 Time (ms) 4 FTR-F3 Series ■■ Dimensions • Dimensions Changeover contact type 7 +0.2 3.3 15 +0.3 23.4 +0.2 2.7 8.8 5 5 4.7 * Dimensions of the terminals do not include thickness of pre-solder. • Schematics (BOTTOM VIEW) 1 NC 5 2 COM 3 NO 6 • PC Board Mounting Hole Layout (BOTTOM VIEW) (23.4) 2.7 8.8 5 5 5 -φ1.1 (1.25) 4.7 (7) (1.32) ( ): Reference value Unit: mm * Tolerance of PC board mounting hole layout : ±0.1 unless otherwise specified. 5 FTR-F3 Series GENERAL INFORMATION 1. ROHS Compliance • All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including amendments. • Use of Cadmium in electrical contacts is exempted as per Annex III of the RoHS directive 2011/65/EU. • Please consider expiry date of exemption. Relays with Cadmium containing contacts are not to be used for new designs. All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/downloads/MICRO/fcai/relays/lead-free-letter.pdf Characteristic data is not guaranteed values, but measured values of samples from production line. • 2. Recommended lead free solder condition • Recommended solder for assembly: Sn-3.0Ag-0.5Cu. Flow Solder Condition: Pre-Heating: maximum 120˚C within 90 sec. Soldering: dip within 5 sec. at 255˚C ± 5˚C solder bath Relay must be cooled by air immediately after soldering Solder by Soldering Iron: Soldering Iron: Temperature: Duration: 30-60W maximum 350-360˚C maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity • Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers • Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 6 FTR-F3 Series Fujitsu Components International Headquarter Offices Japan FUJITSU COMPONENT LIMITED Shinagawa Seaside Park Tower 19F, 12-4, Higashi-shinagawa 4-chome, Shinagawa-ku, Tokyo,140-0002, Japan Tel: (81-3) 3450-1682 Fax: (81-3) 3474-2385 Email: fcl-contact@cs.jp.fujitsu.com Web: www.fujitsu.com/jp/fcl/ Asia Pacific FUJITSU COMPONENTS ASIA, LTD. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components North and South America FUJITSU COMPONENTS AMERICA, INC 2290 North First Street, Suite 212 San Jose, CA 95131, USA Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: us.fujitsu.com/components China FUJITSU ELECTRONIC COMPONENTS (SHANGHAI) CO., LTD. Unit 4306, InterContinental Center 100 Yu Tong Road, Shanghai 200070, China Tel: (86-21) 3253 0998 Fax: (86-21) 3253 0997 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components Europe FUJITSU COMPONENTS EUROPE B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fujitsu.com/uk/components Hong Kong FUJITSU COMPONENTS HONG KONG CO., LTD Unit 506, Inter-Continental Plaza No.94 Granville Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: (852) 2881-8495 Tex: (852) 2894-9512 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components/ Korea FUJITSU COMPONENTS KOREA LIMITED Alpha Tower #403, 645 Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, 13524 Korea Tel: (82) 31-708-7108 Fax: (82) 31-709-7108 Email: fcal@sg.fujitsu.com www.fujitsu.com/sg/products/devices/components/ ©2017 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. September 26th, 2017 7
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Create Date : 2017:09:26 08:15:54+02:00 Creator : Adobe InDesign CC 2017 (Windows) Modify Date : 2017:09:26 15:55:31+09:00 Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2017:09:26 15:55:31+09:00 Creator Tool : Adobe InDesign CC 2017 (Windows) Instance ID : uuid:85c95477-6ef6-4f6e-8cb1-50e7892454fe Original Document ID : xmp.did:f2b12054-75ff-6348-9852-45bc1cd7ebb5 Document ID : xmp.id:ee71a687-1452-b541-bc83-ae463816546c Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:ed614295-8237-1d4b-b98e-2959cdca6418 Derived From Document ID : xmp.did:ed614295-8237-1d4b-b98e-2959cdca6418 Derived From Original Document ID: xmp.did:f2b12054-75ff-6348-9852-45bc1cd7ebb5 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2017 (Windows) History Changed : / History When : 2017:09:26 08:15:54+02:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 7EXIF Metadata provided by EXIF.tools