Furuno USA 9ZWRTR100 Transceiver for Radar model FAR-1518/1528 User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2768686
Application ID	wtHJdyLoTxrWJSol/koVcg==
Document Description	Installation Manual Part 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	243.28kB (3041021 bits)
Date Submitted	2015-09-30 00:00:00
Date Available	2016-03-28 00:00:00
Creation Date	2015-09-14 17:40:06
Producing Software	Acrobat Distiller 10.1.14 (Windows)
Document Lastmod	2015-09-14 17:42:34
Document Title	untitled
Document Creator	FrameMaker 11.0.2

2. WIRING
10. Connect the coaxial cable to the TNC connector (local supply).
Pass the coaxial cable behind the plate
(pointed by arrow) and the clamp
(circumscribed with a dashed circle).
11. Set the transceiver module to the antenna unit. Connect plugs P821, P801, P802,
P822 and the TNC connector. Push the transceiver module in until it stops, and
then tighten fixing bolts. Be sure to push in the transceiver unit until it stops.
Failure to do so may cause microwave leakage.
12. Fasten the shield wire to the wing nut on the transceiver module.
13. Confirm that all screws are tightened and all wirings are properly made. Confirm
that waterproofing gasket, bolts and tapping holes of antenna unit are coated with
silicone grease. Close the antenna unit cover.
2-5
2. WIRING
2.3
How to Connect the Signal Cable for FAR-1513,
FAR-1523
In order to minimize the chance of picking up electrical interference, avoid where possible routing the signal cable near other onboard electrical equipment. Also, avoid running the cable in parallel with power cables.
How to fabricate the signal cable
Fabricate the signal cable as follows:
1. Remove shrink tubing from the signal cable.
2. Remove vinyl sheath approx. 50 mm.
3. Wrap vinyl tape at the end of the vinyl sheath.
Sheath
Remove shrink tubing.
Cut sheath approx. 50 mm.
50
Braided shield
Vinyl tape
2-6
2. WIRING
How to connect the signal cable
1. Open the antenna cover by loosening four bolts, and then fix the stay.
Cable entry
RTB board cover
2. Unfasten the cable gland assembly (gasket, flat washer).
3. Pass the signal cable with connector through the bottom of the antenna unit chassis. Pass the cable through the gland assembly as shown below.
Fixing bolt
4-M4x16
Gasket support
Gasket
Flat washer
Cable entrance
entry
4. Fasten the gasket support with four bolts. Using one of the four bolts, fasten the
crimp-on lug to the shield wire.
5. Fasten the crimp-on lug on the shield to one of the fixing bolts of the cable gland
assembly.
Signal cable
Fasten shield to screw.
Gasket
6. Unfasten four screws to remove the RTB board cover.
2-7
2. WIRING
7. Connect the plugs of the signal cable to the RTB board.
RTB board
J820
J823
J824
J821
8. Reattach the RTB board cover.
9. Attach three EMI cores to the signal cable at the locations shown below.
EMI Core RFC-13 (2 pcs) EMI Core RFC-H13 (1 pc)
2-8
2. WIRING
10. Fasten the signal cable with the cable clamp as follows.
a) Dismount the cable clamping plate and remove the cable clamp and gasket.
Remove gasket.
Cable clamping plate
Remove clamp.
b) Run the signal cable as shown below.
2-9
2. WIRING
c) Fasten the signal cable with the cable clamp as shown below.
Cable clamp
RTB board cover
Top view
11. Release the stay and close the cover. Loosely fasten the fixing bolts; you will have
to make some adjustments inside after completion of wiring.
Note: When closing the cover, set the gaskets to the grooves in the bottom chassis,
then tighten the fixing bolts.
Bottom
chassis
Groove
Gasket
Fixing bolt
Torque : 9.8 Âą0.1 Nm
2-10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2015:09:14 17:40:06+09:00
Creator                         : FrameMaker 11.0.2
Modify Date                     : 2015:09:14 17:42:34+09:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2015:09:14 17:42:34+09:00
Creator Tool                    : FrameMaker 11.0.2
Format                          : application/pdf
Title                           : untitled
Document ID                     : uuid:2afe691a-33c2-4124-a2f7-fb40be8e188a
Instance ID                     : uuid:7579479b-a0de-4237-aef6-6467c58aa171
Producer                        : Acrobat Distiller 10.1.14 (Windows)
Page Count                      : 6

EXIF Metadata provided by EXIF.tools